Honeywell 5834-4 Series Installation And Setup Manual

GENERAL INFORMATION

The 5834-4 key transmitter is a portable wireless transmitter for use only with wireless alarm systems that support 5800 Series receivers

(ex. VISTA series, LYNX PLUS, LYNX Touch).

• Buttons are typically used for arming and disarming, but can be

programmed for any appropriate zone response.

• A button must be pressed and held until the LED begins to flash

to activate a button function. This press and hold feature

minimizes the possibility of accidental transmissions.

• The factory-installed replaceable lithium battery provides power

for up to five (5) years.

For complete details on how to program the transmitter at the control panel, see the control unit's Installation Instructions. When

programming, note the following:

• Each 5834-4 transmitter has two unique serial numbers assigned

during manufacture.

• Each button on the unit also has a distinct "loop" number (refer to the

Loop Number diagram at right) that you must program into the control

panel during installation.

• Assign each button to an individual zone and designate the Input Type

as "BR" (Button Type).

• When prompted for the serial number, press and release the

appropriate button(s) twice, or, manually enter the serial number at the

keypad.

NOTE: Serial #2 is one (1) digit higher than serial #1, which is printed

on the rear of the transmitter.

USING HIGH-SECURITY MODE

If used with LYNXR Series controls earlier than Revision

13.1, Standard Mode must be selected.

To use High Security mode, first select High Security mode, then activate

it. Activation syncs the keyfob with the security system.

1. Select High Security mode:

Mode

Simultaneously hold down for 5 secs...

High-Security

A - C - D (LED flashes Red when transmitting)

Standard

B - C - D (LED flashes Green when transmitting)

2. Activate High Security Mode: Put the security system into Go/No Go

Mode, then press the appropriate set of buttons as follows:

Serial Number Simultaneously hold down until beeps sound...

1

A - B - C buttons (system beeps twice to confirm)

2

A - B - D buttons (system beeps twice to confirm)

ASSIGNING A WIRELESS KEY TO A USER

• On most control panels, if the wireless key is assigned to arm and disarm the system, you must assign it to a user in order for it to

operate. This is accomplished through User Code programming at the control panel. See the control panel's Installation and Setup

Guide for specific instructions on programming User Codes.

The table below summarizes the procedures.

• If programming arming and disarming functions on both serial numbers, each serial number must be assigned to a separate user.

On Vista 32/40/50/50P/100 and up

You must assign a user to the button in order for it to operate.

To assign a user number to the Arm/Disarm button:

1. Enter [4-digit User Code] + [8] + [User No.] + [new User Code].

2. Answer Yes or No to the "Open/Close Report ?" question.

3. Answer Yes to the "RF Button ?" question.

4. Enter the zone number assigned to the button.

5. Keypad display shows summary of user information.

6. Test all functions for proper operation.

I

NSTALLATION AND SETUP GUIDE

Wireless Key Transmitter

• The 5834-4 transmitter provides up to eight (8) functions and has

an optional high security (encrypted) mode that sends rolling-

code encrypted messaging to the RF receiver.

High Security Mode Note: If used in high security mode, must

be used with a receiver or control that supports high security

mode. i.e., 5881EN, 5883, 6150RF, or 6160RF receiver or

LYNXR Series control panel (Rev 13.1 or higher).

Loop Numbers for the 5834-4 Keyfob Buttons

A

SERIAL #1

LOOP 3

SERIAL #2

LOOP 3

C

SERIAL #1

LOOP 4

NOTE

1.

SERIAL #1 FUNCTIONS ACTIVATE WHEN THE RESPECTIVE

BUTTON IS HELD DOWN UNTIL THE LED FLASHES.

2.

SERIAL #2 FUNCTIONS ACTIVATE WHEN THE TWO RESPECTIVE

SERIAL #2 BUTTONS ARE PRESSED AT THE SAME TIME AND

HELD DOWN UNTIL THE LED FLASHES.

Using a Button: To activate a programmed function,

press and hold the appropriate key(s) until the LED

begins to flash.

On Vista-20P/15P/10P/Vista-21iP and variants

You must assign a user to the button in order for it to operate, and

must enter a sequence of keystrokes as described below.

NOTE: There is a two-second timeout for keystroke commands on

Vista P series panels, therefore you must enter the keystrokes as

quickly as possible.

1. Enter [4-digit Master Code] + [8] + [User Number] +

[# 4] + [two digit zone number] assigned to the fob.

2. Test all functions for proper operation.

5834-4 Series

SERIAL #2

LOOP 1

B

SERIAL #1

LOOP 2

SERIAL #2

LOOP 4

SERIAL #2

LOOP 2

D

SERIAL #1

LOOP 1

5834-008-V1