Page 2
1-800-721-2121 or 1-323-721-2121 Office hours are Monday-Friday, 7:30 am - 4:30 pm PST Or email us at [email protected] Thank You for your patronage. Paramount Fitness Corporation 6450 East Bandini Blvd. Los Angeles, CA 90040 IMPORTANT SERIOUS INJURIES TO USERS, BYSTANDERS OR INSTALLERS CAN OCCUR IF THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL ARE NOT FOLLOWED.
ABLE ONTENTS ........................4 AFETY ................ENERAL ARE AND AINTENANCE ................... 8 IMENSIONS AND EIGHT ......................9 REPARATION .................... 10 ARTON ONTENTS .................... 11 ARTON ONTENTS & A NSTALLATION SSEMBLY 1: A ..............12 SSEMBLE THE RAME 2: A .................. 14 SSEMBLE THE 3: A &...
AFETY ACILITY AND AFETY RECAUTIONS 1. Review and understand all of the warning labels affixed to this machine and on the facility safety sign. 2. Be certain that the machine operation is understood before it is used. Refer to the instructional Procedure Label affixed to the machine.
Page 5
AFETY 12d. This equipment is designed for standard olympic size weight plates with a 50mm bore (1.9”). 12e. Do not exceed the maximum weight capacity of the machine. Maximum plate size is 45 lbs. (25 kg.). 13. On Selectorized and Cable equipped machines: 13a.
Page 6
AFETY AINTENANCE AFETY RECAUTIONS 1. Refer to Maintenance Schedule label on the machine as well as this manual for when to perform maintenance. 2. Check the function of your machine DAILY by verifying the following: • Inspect cables and end fittings for any signs of wear. Replace if worn, frayed or damaged with original Paramount replacement components.
Page 7
13. Be sure all hardware is tight before using the machine. Retain these instructions for future reference. If you have any questions, do not hesitate to contact your Paramount dealer or Paramount Fitness Corp. at (800)721-2121 or [email protected].
REPARATION EQUIRED OOLS Ratchet Wrench and Socket: 9/16” Wrenches: 9/16”, 3/4” (or an adjustable crescent wrench). Rubber mallet. Allen wrenches: (included with the machine) Weight Plate Cartons Depending upon your order, this machine can be assembled with either a 170 lb. or 250 lb.
ARTON ONTENTS ITEM UMBER ESCRIPTION FS55-UPR-000X FRAME, UPRIGHT FS55-SHD-100X SHROUD, FRONT FS-SHD-250X SHROUD, REAR FS-GRD-200X GUIDE ROD ASSEMBLY FS-BKT-000 GUIDE ROD BRACKET FS-WSB-000 WEIGHT STACK BASE FS-CAP-000X TOP CAP FS-BKT-001 BRACKET, TOP CAP FS55-PAD-000X PAD, BACK FS54-PAD-100X PAD, SEAT...
ARTON ONTENTS ITEM UMBER ESCRIPTION FS55-MFR-300X MAIN FRAME, SUPPORT FS55-SFR-200X SEAT FRAME FS55-MFR-200X MAIN FRAME, BOTTOM FS55-SFR-100X SEAT FRAME, SEAT FS55-AXL-100X AXLE, PIVOT FS55-ARM-400X RIGHT ARM FS55-ARM-100X LEFT ARM FS55-MFR-100X MAIN FRAME, TOP FS55-AXL-200X CAM, RIGHT ARM FS55-AXL-300X CAM, LEFT ARM FS55-PHS-000X FLOATING PULLEY SET FS-SBR-000X...
Page 12
1: A SSEMBLE THE RAME 1. Assemble frame components as shown. ITEM UMBER ESCRIPTION FS55-UPR-000X UPRIGHT FRAME 2. Tighten all the hardware after the FS55-MFR-300X MAIN FRAME, SUPPORT components have been aligned. FS55-MFR-100X MAIN FRAME, TOP FS55-MFR-200X MAIN FRAME, BOTTOM FS55-SFR-200X SEAT FRAME C 445...
Page 13
1: A SSEMBLE THE RAME 12,7,10,11,9 12,8,11,9 6,10,9 12,13,11,9 12,13,11,9 12,6,10,11,9 X 2 12,6,11,9...
2: A SSEMBLE THE 1. Insert the axle from the top of ITEM UMBER ESCRIPTION the main frame and install the FS55-AXL-100X AXLE, PIVOT cam onto the axle. Align the FS55-AXL-300X CAM, LEFT ARM holes on the cam and the axle FS55-AXL-200X CAM, RIGHT ARM and install the spring roll pin.
Page 16
3: A & B SSEMBLE THE 1. Install the seat pad and back pad as ITEM UMBER ESCRIPTION shown below. FS55-SFR-100X SEAT FRAME, SEAT 2. Tighten all hardware shown below. FS54-PAD-100X PAD, SEAT FS55-PAD-000X PAD, BACK C-446 SCREW, HH, 3/8-16 x 1-1/4” C 749 WASHER, LOCK, 3/8 C 754C...
4: A SSEMBLE THE EIGHT TACK 1. Install selector pin and floating pulley ITEM UMBER ESCRIPTION housing as shown. Leave about 1/4 FS55-PHS-000X FLOATING PULLEY SET inch spacing between the bottom of FS-SFR-000X TOP PLATE/SELECTOR BAR the housing to the top of the nut. Lock FS-SPN-000X SELECTOR PIN the housing in place with the nut as...
5: I NSTALL THE ABLE 1. Route the cable as shown on page ITEM UMBER ESCRIPTION FS55--UPR-022 PULLEY PROTECTOR 2. Install all the pulleys as shown B 900 PULLEY, 4-1/2” DIA below. Lean the guide rods out to FS55-CBL-100X CABLE install the bolts inside the upright C 448 SCREW, HH, 3/8-16 X 1-3/4”...
6: I NSTALL THE RONT HROUD 1. Install the front shroud as shown ITEM UMBER ESCRIPTION below. FS55-SHD-100X SHROUD, FRONT 2. Secure the guide rod by installing the FS-BKT-000 GUIDE ROD BRACKET guide rod brackets. C 445 SCREW, HH 3/8-16, 1” C 754C WASHER, FLAT, 3/8 3.
Page 21
7: I & T NSTALL THE HROUD 1. Assemble the rear shroud as ITEM UMBER ESCRIPTION shown. FS-SHD-250X SHROUD, REAR 2. Operate the machine and make FS-CAP-000X TOP CAP sure that the weight stack clears FS-BKT-001 TOP CAP, BRACKET the shroud. Adjust the position if C 444 SCREW, HH, 3/8-16 X 3/4”...
Page 22
8: I NSTALL THE EIGHT TACK ABEL 1. Select the appropriate weight stack label(s) according to your order. You can install pound labels, kilogram labels, or both. 2. If you ordered a 170 lb. weight stack, use labels: LBL-WSE-01170 (for pounds) LBL-WSM-01170 (for kilograms).
Page 23
ACHINE ABELS The following are the Warning labels required for this FS machine. If any of these labels are missing or become damaged, Paramount will replace them free of charge. Note: these labels are not to scale. WARNING SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT IF THE CABLES AND THEIR ATTACH- MENT COMPONENTS ARE NOT...
ERVICE O W T O B T A I N E R V I C E For warranty service, contact an Authorized Paramount Dealer or a Paramount Customer Service representative at 1-800-721-2121 or 1-323-721-2121. You can also email us at [email protected].
FS B NSTRUCTIONS The machines in this product line were designed and tested to meet the ASTM (American) and EN (European) safety standards for stability (without floor anchors) when the machine is used for it’s intended purpose as designated by the manufacturer. However, Paramount strongly recommends that all equipment be anchored to the floor to prevent movement and increase stability.
AUTHORIZED CORPORATE OFFICER OF PARAMOUNT. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY, FROM STATE TO STATE. CONTACT PARAMOUNT FITNESS CORP., 6450 E. BANDINI BLVD., LOS ANGELES, CALIFORNIA 90040-3185, FOR A LIST OF AUTHORIZED DEALERS OR BEFORE RETURNING ANY DEFECTIVE...
Page 28
Paramount Fitness Corporation 6450 E. Bandini Blvd. Los Angeles, CA 90040-3185 Phone: 1-323-721-2121 Fax: 323-724-2000 1-800-721-2121 www.paramountfitness.com...