Quick Links
Operating Notes
Power Supply
This dome camera can operate on 24 VAC or 12 VDC.
Operating Conditions
Avoid:
•
Viewing bright objects (for example, light fixtures) for extended
periods
•
Operating or storing the unit in the following locations.
•
Extremely humid, dusty, hot/cold environments (where the
operating temperature is outside the recommended range of
14°F to 122°F [-10°C to +50°C])
•
Close to sources of powerful electromagnetic radiation, such
as radio or TV transmitters
•
Close to fluorescent lamps or objects reflecting light
•
Under unstable light sources (may cause flickering)
Warnings (where applicable to your locale)
Installation and servicing should be performed only by qualified and experienced technicians
to conform to all local codes and to maintain your warranty.
WARNING!
The use of CSA Certified/UL Listed Class 2 power adapters is required to
ensure compliance with electrical safety standards.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product
(applicable in the European Union and other European countries with separate collection
systems). This product should be disposed of, at the end of its useful life, as per applicable local
laws, regulations, and procedures.
Product Dimensions
3.37" (85.5 mm)
4.9" (124.6 mm)
∅ 3.97"
3.0" (76.2 mm)
(101 mm)
4.9" (124.6 mm)
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits for a
Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
•
Consult the dealer or a radio/TV technician for help.
Caution
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer's Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the essential
protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23
EEC, conforming to the requirements of standards EN 55022 for emissions.
Contact Information
1.68"
(42.8 mm)
© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without
written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all
respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use
thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication
may be issued to incorporate such changes.
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
Document 800-00789 – Rev C – 07/08
3 Inch Dome Camera
Quick Install Guide
1
Preparation
2
Camera Mounting
3
Camera Adjustment
4
Installation Completion
Contents
Fully assembled camera
Mounting template
1
P
e r
p
r a
t a
o i
n
2
C
a
m
e
a r
M
o
u
1. Remove the dome cover
4S Electrical Junction Box
a.
Gently turn the dome cover counter-
clockwise to unlock, then pull free of
Electrical box (not
the housing.
supplied)
b.
Gently pull the inner liner free of the
two notches in the housing.
c.
Set the dome and liner aside.
Adapter plate
(optional)
After mounting
and adjusting
Base
the camera, attach the dome
cover:
a.
Attach the inner liner to the base until
the liner clicks into place.
b.
Align the dome cover with the three
dome tabs on the unit.
c.
Turn the dome gently clockwise until it
locks into place.
2. Connect the wiring
Surface Mount
24 VAC/12 VDC power connector
Adapter plate
(optional)
Video output connector
a.
Connect the video output
connector.
Skirt
b.
Connect the 24 VAC/12 VDC power
connector.
3. Prepare the mounting surface (surface or flush mount)
a.
Mark the holes.
b.
Insert screw anchors into
holes.
Hardware kit
This guide
Document 800-00789 – Rev C – 07/08
t n
n i
g
3
C
a
m
e
a r
A
d
u j
t s
m
e
t n
a.
Turn the Axis ring in the desired
direction, then retighten.
a.
Adapter plate (optional). Secure to
b.
Turn the Zoom lever slightly
electrical box using appropriate screws
counter-clockwise to loosen.
(not supplied).
ring
Axis
Then rotate around the lens for
b.
Secure camera base to ceiling or wall.
the desired image view.
c.
Turn the Focus lever counter-
clockwise to loosen. Rotate to
adjust for the best picture
quality.
Zoom
d.
Retighten the Zoom and Focus
Focus
lever
lever
making adjustments.
levers to lock them after
Do not turn the lens more than 360°.
the levers and axis ring.
Do not use excessive force to loosen
Optional Camera Settings
Monitor out
Flush Mount
DIP switches
Mode setting
1 2 3 4 5 6 7 8
Note
Please use the supplied DC Iris and Line Lock adjustment tool to adjust picture
brightness and phase adjustment.
Picture Brightness
Use the LEVEL screw to compensate for the iris level. L (low) darkens t
picture. H (high) brightens the picture.
Phase Adjustment
Use the V Phase Adjustment Pot to adjust the phase difference betwe e
cameras. Make sure Switch 4 is ON to activate the Line lock function ( A
operation only).
a.
Adapter plate (optional for ceiling tile).
DIP Switches
Switch Function
Secure using appropriate screws (not
1
BLC (Backlight Compensation). ON = camera automatically
supplied).
adjusts the exposure. OFF = factory default.
Surface mount: Secure skirt to ceiling or wall
2
AGC (Automatic Gain Control). ON = camera adjusts for low
using _______ screws supplied.
light conditions. ON = factory default.
b.
Secure camera base with ______________
3
DC/AES Mode. Leave in ON position only.
screws, supplied.
4
LL (Line Lock). Set the camera synchronization to internal or
Line lock (only available with 24 VAC). ON= factory default.
Related Manuals for Honeywell 3 inch dome camera
Summary of Contents for Honeywell 3 inch dome camera
-
Page 1: Operating Notes
Make sure Switch 4 is ON to activate the Line lock function ( A operation only). © 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without Adapter plate (optional for ceiling tile). -
Page 2: Optional Camera Settings
Preparation Camera Mounting Camera Adjustment 1. Remove the Dome Cover 4S Electrical Junction Box Gently turn the dome cover counter- clockwise to unlock, then pull free of Electrical box the housing. If required, loosen the Secure the adapter plate to the (not supplied) security screw first.