Table of Contents
R980 500 366 07/09
Modular Transfer System Belt Grinder
Important Safety Information!
IMPORTANT: This manual must be
reviewed with all equipment operators
as part of your operator training
program!
SAFETY FIRST!
I m p o r t a n t s a f e t y i n f o r m a t i o n i s
contained throughout this manual to
alert you to potentially dangerous situations
and help prevent accidental injury and
property damage.
The safety warning symbol above has been
included to warn you of hazards that can
hurt or kill you and others, and/or cause
serious damage to the equipment and
other property. In addition, the following
safety alert words are used:
DANGER!
Means that you or others will be seriously
or fatally injured if instructions are not
followed.
WARNING!
Means that you or others may be
seriously or fatally injured if instructions
are not followed.
CAUTION!
Means that you or others may be injured
if instructions are not followed.
Material Hazards:
Some components, such as gearboxes,
contain lubricants or other materials that can
represent a potential health hazard if han-
dled, stored, or disposed of improperly.
Please contact Bosch Rexroth for copies
of the Material Safety Data Sheets (MSDS)
for the lubricating oil used in gearboxes and
other potentially hazardous materials.
Review All Safety Information:
Please review the safety information
included on this page and throughout this
manual with all installers, operators, and
maintenance personnel of this equipment.
SAVE THESE INSTRUCTIONS
Please read all assembly, and mainte-
nance instructions carefully before be-
ginning set-up of the components in this
document. Where appropriate, warning
symbols
have been included in this
publication to alert you of potential or
impending danger.
Be sure to read and observe all safety
•
warnings in this document as well as
those attached to the individual mod-
ules. Failure to do so could result in
potential risks to your health and safety
as well as those around you.
•
Covers and guards have been de-
signed to eliminate pinch points and
exposure to moving chains and gears.
DO NOT operate the conveyor or any
of the other components in the system
with the guards removed. Serious
injury may result!
•
All set-up maintenance and repair work
should be performed only by properly
trained, qualified personnel. All opera-
tors must be properly trained in the use
of this equipment.
•
A qualified electrician must make all
electrical connections when wiring the
components installed in the TSplus
system. Be sure to follow all local,
state and federal regulations when
installing electrical devices of any type.
The customer assumes responsibility
for the control system, and must pro-
vide an EMERGENCY-OFF SWITCH
or switches for all workstation opera-
tors to meet all applicable industry and
OSHA requirements. In general, emer-
gency-off switches must be present
at easily accessible locations for all
operators of the installed TSplus
conveyor system.
•
All power supplies must be LOCKED
OUT before beginning maintenance or
repair work of any type on the conveyor
system. Proper LOCK OUT procedures
include the identification of the locked
out power supply with a tag to prevent
the accidental restoration of power.
Employees must be instructed in safety requirements. Refer to Rexroth docu-
ment 3842527147 (2008.02), "Instructing Employees on Safety" for an overview
of the dangers, instructions and references to regulations and standards for em-
ployees who operate, maintain, repair or who work on or near Rexroth conveyor
transport systems. A pdf of this multi-language document can be downloaded at:
BoschRexroth-US.com/BRLCatalogs by clicking on "Manuals and Product Updates"
Bosch Rexroth Corporation
WARNING!
•
TSplus pneumatic components are
designed to operate in a range of 4–6
Bar (58–87 psi). It is the users respon-
sibility to install a filtered, regulated
air supply to limit the pressure to that
recommended by the manufacturer.
Before beginning any maintenance or
repair, bleed off the pressure lines to
all components to prevent unexpected
or accidental movement of a system
component which could result in
personal injury.
•
TSplus drives, returns and conveyor
sections, lift-rotate units and compo-
nents are designed to transport Bo-
sch Rexroth WT2, WT2/A, WT2/A-H
workpiece pallets. Proper usage is
defined as the transport and position-
ing of parts and assemblies via the
workpiece pallet and fixture during the
assembly process. In no instances
should the pallet payload, the down-
ward force applied to the pallet, or
the total load carrying capacity of the
entire system be exceeded. Exceed-
ing published specifications will result
in premature wear or system failure
and may cause damage to the motor,
gearbox, roller chain, seals and other
components.
CAUTION! Do not operate or work
•
near mechanical equipment when
wearing loose clothing. Moving compo-
nents such as roller chain, drive belts,
drive shafts and pallets can snag long
belts, scarves, ties and other loose
fitting garments, pull the worker into
the equipment and cause serious, or in
extreme cases, life threatening injury.
CAUTION! Operators having long hair
•
must wear appropriate head protection
(hair nets, hats, and hair caps) to mini-
mize the risk associated with working
near moving machinery. Hanging hair
can get caught in moving components
such as roller chain, drive belts, drive
shafts and pallets, pull the worker into
the equipment and cause serious, or in
extreme cases, life threatening injury.
WARNING!
3
Table of Contents
