Protected network stations, equipped with mds inet series, entranet, or mercury transceivers (50 pages)
Summary of Contents for GE 0150-0241 ProBridge
Page 1
User Manual 0150-0241 Phillips ProBridge...
Page 2
800-469-1676 (6 A.M. – 5 P.M. PST Monday through Friday) Tech Support 541-740-3589 (all other times) Main 800-343-3358 or 541-754-9133 Fax: Tech Support 541-752-9096 (available 24 hours a day) Main 541-754-7162 Web: www.GE-Security.com 0150-0241B / May 2004 Philips ProBridge 0150-0241B...
1 Philips ProBridge 1.1 Philips ProBridge Description The Kalatel CBR-PB2-PHILIPS is a specific ProBridge unit for interfacing the DVMRe family of digital video multiplex/recorders and providing local keyboard control via a CBR-KB3 or KTD-405 keypad to a Philips AutoDome. Kalatel Components: (1) CBR-PB2-PHILIPS ProBridge.
Connector: 2.1mm female barrel. Center Positive 4310-0008 220VAC Power Supply Power Supply Input Voltage: 220 Volt AC Tolerance: ±10% Frequency: 50 Hz Power Supply Output Voltage: 12 Volt DC Current: 110mA Power: 1.3 Watts Connector: 2.1mm female barrel. Center Positive Philips ProBridge 0150-0241B...
(see the Appendix for RS-485 addressing). Using the provided cable, connect from the ProBridge RCVR/DRVR port to the Philips Data Converter Unit (LTC 8780). See the Philips Data Converter Unit’s (LTC 8780) installation manual for information on connecting the LTC 8780 to the AutoDome.
1.6 Connection Diagrams This drawing depicts one Philips AutoDome connected via an RS485/422 network to a Kalatel DVMReTriplex unit, that provides remote PTZ control over Ethernet via WaveReader software, and a CBR-KB3 or KTD-405 keypad. Philips AutoDome DB9-F LTC 8780...
Check that each device is properly powered. Check that all cables and cable connections are correct. Verify that the Dome addresses and Unit ID are correct. If the interface still does not work correctly contact Technical Support. Philips ProBridge 0150-0241B...
(JP2, JP3, JP4 and JP5). The other set, located at the bottom of the board (P6, twelve pin header) determines specific configuration elements for equipment interfacing. ProBridge Circuit Board Philips ProBridge 0150-0241B...
Page 11
Not Installed P6 Pin 6 Not Installed P6 Pin 7 Not Installed P6 Pin 8 Not Installed P6 Pin 9 Not Installed P6 Pin 10 Not Installed P6 Pin 11 Not Installed P6 Pin 12 Not Installed Philips ProBridge 0150-0241B...
DC jack, positive center. Power Supply Voltage: 12 VDC Current: 110 mA Power: 1.3 W All specifications are subject to change without notice. Kalatel NOTE believes that all specifications are correct, however no liability is assumed for omissions or errors. Philips ProBridge 0150-0241B...
RS-485 data line. Consult the PTZ installation manual for specific instructions on setting these addresses. The CBR-PB2-PHILIPS can be used in conjunction with multiple NOTE Kalatel units, and/or keypads controlling the domes and the Kalatel units.
6.2 Philip AutoDome Addressing The Philips AutoDome can be addressed from 1 to 9998. The CBR-PB2- PHILIPS ProBridge can control camera addresses from 1 to 9998, however the CBR-KB3 keyboard can control cameras from 1 to 1024. WaveReader software can only control cameras from 1 to 8160.
8129 – 8160 Philips AutoDome Addresses are calculated as follows: NOTE Philips AutoDome Address = Camera Address + 32 X (Network Address – 1) Philips Data Converter Unit Switch Setting Set the switches on the LTC8780 as follows: S101: Switches 1, 3, and 4 set to OFF. Switch 2 set to ON.
Start Advanced Menu Mode. 6.5 Preset Operations The Philips AutoDome can store up to 99 preset operations (1-99). With the remote keyboard, the number of presets that can be set up is 32 (1-32). With WaveReader, the number of presets that can be set up is 16 (1-16).
Page 17
Navigate the camera to the desired location, select the desired preset from the drop down list box, then click Set. To send the camera to the desired preset, select the preset from the drop down list box, then click Go To. Philips ProBridge 0150-0241B...
Repaired equipment will be returned via the same method of shipment in which it was received. If a customer requests a faster return shipment, the difference will be charged. For all non-warranty repairs, the customer will be billed for parts, labor, and shipping. Labor will be billed in half-hour increments. Philips ProBridge 0150-0241B...
Page 19
From 1 year to 3 years from purchase, the product must be sent in for repair. Advance replacements will be sent for a fee of $100. If you have questions about this policy, please contact GE Security’s RMA Department at 800-469-1676. Philips ProBridge 0150-0241B...