Table of Contents
Related Manuals for Hitachi CM2096ME
Summary of Contents for Hitachi CM2096ME
- Page 1 HITACHI COLOR MONITOR CM2096ME USER MANUAL For future references, record the serial number of your display monitor. SERIAL No. The serial number is located on the rear of the monitor. EPA POLLUTION PREVENTER READ THE INSTRUCTION INSIDE CAREFULLY. KEEP THIS USER’S MANUAL FOR FUTURE REFERENCES.
- Page 3 USER MANUAL MANUAL DE USUARIO GEBRUiKSAANWiJZlNG MODE D’EMPLOI Energy Star is a trademark of Environmental Protection Agency. The Energy Star emblem does not represent EPA endorsement of any product or service.
-
Page 4: About Cleaning
The information in this manual is subject to change without notice. Hitachi assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGMENT VGA is a registered trademark of international Business Machines Corporation. APPLE is a registered trademark of Apple Computer, Inc.. - Page 5 CAUTION for 200V operation only in U.S.A. This equipment relies on the protective devices in the building installation for short - circuit and over - current protection. Refer to the following table for the suitable number building and location of the protective devices which should be provided in the installation.
- Page 6 SPECIFICATIONS . , ..........The following features are provided by the Hitachi Color Monitor CM2096M.
-
Page 7: Front View
install the monitor in the following way, taking care to maintain safety. Front Cover L , CRT Surface I Power Switch Control Panel A ‘Tilt & Swivel Base FRONT VIEW ,..-..~..,..-..~..-........... Contrast - Power Store ’ ’ ’ ’ ’ Button Increase Switch Button -... -
Page 8: Installation
1. Installation ) Install the monitor on a horizontal base. INSTALL THE UNIT IN ADEQUATE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is designed to be used in an office or business environment. DO NOTsubject the unit to vibrations, dust, or corrosive gases. -
Page 9: Electrical Connection
Use only the correct voltage power outlet with safety ground connection. 110 - 120 V for USA, Canada, etc. 200 - 240 V for Europe. etc. (This monitor automatically selects the input voltage 110 - 1201200 - 240V.) The receptacle should be close to the monitor and easily accessible. FOR THE CUSTOMERS IN U.K. - Page 10 3. Signal Cable Connection D-Sub Mini 1 S-pin Connector Terminal Shell (connected to Frame Ground) TABLE 1 ) Use an optional signal cable for a VGA-type graphics board. ) Connect the connector to the “D-Sub Mini 15-pin Connector Terminal”, and secure the screws on the connector shell firmly.
- Page 11 4. Power On ) Turn the Power Switch of the monitor (refer to “OPERATION - Power Switch”) on first, then the computer. NOTICE: If the picture doesn’t appear, turn OFF the power switch, make sure of the following, wait at least 30 seconds, and turn it back ON. Make sure the power switch of the computer, power cord connection, signal cable connection, and the input sync.
-
Page 12: Function Of Controls
See the “Control Panel” at front of the monitor. You can adjust the picture position, size, side pincushion, trapezoid, rotation, color balance, brightness and contrast of the monitor with these buttons. If two or more buttons are pressed at the same time, they will be invalid except when mentioned in the following. -
Page 13: To Adjust Contrast
1 Increase / Decrease Button [ +] / [ - ] 0 The [+] / [ - ] button increases/decreases the value of any selected item during adjustment. ) Pressing the [ +] / [ -1 button has different results according to the item selected. For instance, the picture will be shifted right by pressing the [+I button when the horizontal position button [a] is selected. - Page 14 1 Color Button [ :. ] 0 Indicates the color balance selection No. ) When the color button is pressed, the color LED will indicate the color balance Flashing selection No. Flashing once indicates the standard color balance No. 1. twrce indicates the standard color balance No.
- Page 15 ) Press the store button to store your settings, after adjustment. It will be restored, when the same video mode is used. (refer to “Store Button”) Rotation[@l]&[~] a t t h e s a m e t i m e = r-1 [+I .
-
Page 16: The Other Functions
2. THE OTHER FUNCTIONS Automatic Settings When the monitor is powered on and connected to a video source, the unit will automatically adjust the followings. ) Contrast, brightness, rotation, and color balance. ) Geometry (position, size, side pincushion and trapezoid), on the video mode. ) Degaussing. - Page 17 Color Balance Selection F When the color button is pressed, the color LED will show you the current color balance selection No. (Refer to “Color button” section.) ) You have a choice of two standard color balance settings No.1 and No.2. And one user color balance setting No.3 is available if you have already stored your own color adjustment.
-
Page 18: Color Balance Adjustment
Color Adjustment Your own color balance can be set by adjusting each color components of red, green and blue. l Color Selection [ :. 1 84 [EDI/[E3 l/[E!J 1 f3l$!dB, , -,, +, DE-& 0 L--J--’ ) When the color button [ :. I and one of [ a] / [a ] / [ 8 ] buttons are pressed, two LEDs of the button pressed will light. - Page 19 ) When the power switch is turned ON while pressing the [+] button and [ - ] button together, all user settings will be deleted. ) The original standard setting will still remain. The following power saving functions are provided by the Hitachi Color Monitor CM2096M. Built-in Automatic Power Saving An automatic power Saving function operates when no horizontal or vertical sync signal is supplied to the monitor.
- Page 20 : 20 inches diagonal, 0.31 mm (horizontal : 0.27 mm)dot pitch (optional 0.28 mm (horizontal : 0.24mm)) Black matrix, Anti-Reflection coat, Short persistence phosphors. input Signal : 0.7 Vp-p, Analog Video : Separate H, V or Composite H/V Sync. TTL level or Sync. on Green at 0.3 Vp-p Synchronization : 30-82kHz Horizontal...