Table of Contents
Quick Links
COLOUR
CM81
CM81
CM81
MONITOR
1ETPIus
3ETPIUS
5ETPIUS
,.
'. ,.
USER
lVIAhllJAL
..... I
BEDIENUNGSANLEITUNG...19
MANUAL
DE
USUARIO...35
MANUALE
D'USO...5I
MANUEL
UTIL]SATEUR...67
with Easy Men u !
EasyMenu is the On Screen Display function for easy operation.
0000000
00 00 0.0
\
READ THE INSTRUCTIONS INSIDE CAREFULLY.
KEEP
THIS USER MANUAL FOR FUTURE REFERENCE.
For future reference, record the serial number of your color monitor.
SERIAL
No.
The serial number is located on the rear of the monitor.
This monitor is
ENERGY STAR@
compliant when used with a computer
equipped with VESA DPMS.
The
ENERGY STAR@
emblem does not represent EPA endorsement
of any product or service.
Table of Contents
Related Manuals for Hitachi CM811ETPlus
Summary of Contents for Hitachi CM811ETPlus
- Page 1 ‘. ,. COLOUR MONITOR USER lVIAhllJAL ..I CM81 1ETPIus BEDIENUNGSANLEITUNG...19 CM81 3ETPIUS MANUAL USUARIO...35 MANUALE D’USO...5I CM81 5ETPIUS MANUEL UTIL]SATEUR...67 with Easy Men u ! EasyMenu is the On Screen Display function for easy operation. 0000000 00 00 0.0 READ THE INSTRUCTIONS INSIDE CAREFULLY.
- Page 2 NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGEMENT VGA is a registered trademark of International Business Machines Corporation. VESA is a trademark of a nonprofit organization, Video Electronics Standard Association. is a U.S.
-
Page 3: Plug And Play
FEATURES ......................l cAuTloNs ......................2 lNsTALLATloN ....................6 STANDARD SE~lNGS ..................8 operation ......................9 POWER SAVING SYSTEM ................l6 PLUG & PLAY ....................l6 sPEclFlcATloNs .....................l7 FEATUI?ES The following features are provided by the Colour Monitor Sharpest Focus and Highest Contrast Flat screen CRT with anti-glare, dynamic focus circuit, dark glass, and an INVAR shadow mask gives the sharpest focus and highest contrast to minimize eye fatigue. - Page 4 NEVER REMOVE THE REAR COVER! — The rear cover MUST be removed only by authorized service personnel. This colour monitor contains high voltage components. THE Receptacle SHOULD BE CLOSE To THE MONITOR AND EASILY — ACCESSIBLE INSTALL THE UNIT IN AN SUITABLE ENVIRONMENT DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard.
- Page 5 9 CAUTION for 200- 240V operation only This equipment relies on the protective devices in the building installation for short-circuit and over- current protection. Refer to the following table for the suitable number and location of the protective devices which should be Drovided in the buildina installation. Informative examples of protective...
- Page 6 E FCC (Federal Communications Commission) STATEMENT WARNING WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide —...
-
Page 7: Important For United Kingdom
FOR THE CUSTOMERS IN THE U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment... -
Page 8: Installation
INSTALLATION Install the monitor in the following way, taking care to maintain safety. — Rear Cover REAR VIEW 1. Installation Install the monitor on a horizontal base. 2. Power Cord Connection @ Make sure of using the power cord meeting the safety standard of the country in which you are using the monitor. - Page 9 Use a signal cable with the D-Sub Mini 15-pin Connector. Input 1 Input 2 Pin No. Red Video Red Video Green Video Green Video (Sync. optional) (Sync. optional) Blue Video Blue Video No Pin No Pin I No connection I No connection Red Ground Red Ground Green Ground...
- Page 10 I STANDARD SETTINGS Microprocessor-based preset functions can store 26 sets of geometry settings The following industrial standard settings have including the standard settings. been pre-programmed by the factory. Video Mode Name Horizontal Video (with Resolution and CM811 CM813 CM815 Frequency Mode Vertical Frequency) 31.47 kHz...
-
Page 11: Power On/Off
0000000 — — /’ I Control Switches @* @_E, ,,i_e @9@J9 e–e—m .2,s 00 ..o.—$. .”— Adjust Switch Select Switch Page 10 “DEGAUSSING” Input Switch Page 9-13 “ADJUSTMENT Page 9 “POWER ONIOFF POWER ON/OFF the Power switch, to switch the power ON or OFF. Press When power is ON, the power LED lights. - Page 12 DEGAUSSING — Press the switch “DEGAUSS”, to degauss manually. Use this only when you see colour impurities function on the screen after turning ON the monitor. Remember, the monitor is automatically degaussed during initial power on. Wait for about 10 minutes before repeating the function.
- Page 13 ADJUSTMENT (Continue) Adjust Switch Select Function Switch Item moves the position to the right. Position moves the position to the left. ‘ expands horizontally. Size shrinks horizontally. moves the position up. Position moves the position down. expands vertically. U. Size shrinks vertically.
- Page 14 ADJUSTMENT (Continue) Adjust Switch — Select — Function Item Switch changes the colour to the next mode. ;olour Select :9300K * No.2:6500K No. I NO.3:5000K No.4:USER (if available) changes the colour to the previous ~~~USER (if available) -+ No.3:5000K No.2:6500K 1:9300K the Red stronger.
- Page 15 ADJUSTMENT (Continue) Adjust Switch Select Item Switch Function operates the horizontal moire changing and~ H. Moire circuit. Reduction simultaneously. stops the horizontal moire changing circuit. makes the operation of the horizontal moire changing circuit stronger, makes the operation of the horizontal moire changing circuit weaker.
- Page 16 STORE You can store your settings automatically when the EasyMenu is disappeared Restoring Condition Storing Condition Item Mhen the monitor One setting is allowed for each video mode. H. Position Ietects the same video H.Size You can store maximum 26 sets of geometry node.
-
Page 17: Signal Check
SIGNAL CHECK ........... . To refer to the input signal condition, press any switch CS CONTRf!ST ‘w (Select Switch or Adjust Switch). horizontal ~IOB -tm~~+ :— frequency and vertical frequency will be indicated. a w?IGHTNESS j 50 E14 ~ bR Precision frequency, 2 kHz... - Page 18 POWER SAVING SYSTEM This monitor complies with VESA power saving ENERGY STAR@ — requirements. The power saving system works only when used with VESA — DPMS compliant PC’s and/or graphic controllers. When to switch the power OFF during the monitor is in OFF mode, sometimes LED flashing continues a few seconds.
- Page 19 mm horizontal dot pitch 21 inch picture tube, 0.22 (0.21 mm horizontal mask pitch), Invar shadow mask, Black matrix, Short persistence — phosphors, New Anti-Reflection coat. Video : 0,70 VP-Q, Analogue Input Signal Sync. : Separate H/V, TTL level ‘. Composite H/V, TTL level Sync.
- Page 20 Hitachi, Ltd. Tokyo, Japan International Sales Division THE HITACHI ATAGO BUILDING, No. 15 –12 Nishi Shinbashi, 2 – Chome, Minato – Ku, Tokyo 105-8430, Japan. Tel: 03 35022111 HITACHI EUROPE LTD. HITACHI EUROPE S.A. Dukes Meadow 364, Kifissias Ave. & 1, Delfon Str.