Related Manuals for GE IC754PBSS01
Summary of Contents for GE IC754PBSS01
- Page 1 QuickPanel* View Communication Module Hardware User’s Guide PROFIBUS Slave Adapter IC754PBSS01 April 2010 GFK-2291B...
- Page 2 Features may be described herein which are not present in all hardware and software systems. GE Intelligent Platforms as- sumes no obligation of notice to holders of this document with respect to changes subse- quently made.
- Page 3 Contact Information If you purchased this product through an Authorized Channel Partner, please contact the seller directly. General Contact Information Online technical support and Global Care http://www.ge-ip.com/support Additional information http://www.ge-ip.com/ Solution Provider [email protected] Technical Support If you have technical problems that cannot be resolved with the information in this guide, please contact us by telephone or email, or on the web at www.ge-ip.com/support...
- Page 4 Contact Information Europe, the Middle East, and Africa Online Technical Support www.ge-ip.com/support Phone +800-1-433-2682 EMEA Direct Dial +352-26-722-780 (if toll free 800 option is unavail- able or if dialing from a mobile telephone) Technical Support Email [email protected] Customer Care Email [email protected]...
- Page 5 The PROFIBUS Slave has been tested and found to meet or exceed the requirements of U.S. (47 CFR 15), Canadian (ICES-003), Australian (AS/NZS 3548) and European (EN55011) regulations for Class A digital devices when installed in accordance with guide- lines noted in this manual. Note: This device complies with Part 15 of the FCC rules.
- Page 6 Installation Installing a Communication Module Warning: Always use anti-static precautions when ac- cessing the mating connector or the interior of the unit. Disconnect the DC input power terminal block connec- tor from your QuickPanel View unit before connecting the Communication Module to the unit. Note: The 6”...
- Page 7 Installation Open the back cover. Attach the Communication Module to the unit by plug- ging the module into the mating connectors on the back of the unit. Caution: Be sure to properly align pins in the dual connector upon insertion to avoid damage to the card or the QuickPanel View unit.
- Page 8 Features Overview The PROFIBUS module is shown below. PROFIBUS Slave Adapter GFK-2291B...
-
Page 9: Profibus-Dp Connector
Features PROFIBUS-DP Connector 9-Pin in D-sub Signal Description (female) B-Line Positive RxD/TxD Request to send GND Bus Isolated ground +5V Bus Isolated +5V A-Line Negative RxD/TxD Case Shield GFK-2291B PROFIBUS Slave Adapter... - Page 10 Features Node Address Switches Before configuring the AnyBus-S PROFIBUS-DP module the node address has to be set. This is done with two rotary switches on the module, this enables address settings from 1-99 in decimal format. Looking at the front of the module, the leftmost switch is used for the ten setting and the rightmost switch is used for the setting of the integers.
- Page 11 Features LEDs Four LEDs are located on the PROFIBUS Slave module. These LEDs indicate the module status and the fieldbus status. Not used Ready (on line) Diagnostics Off line LED no. Indication Description GFK-2291B PROFIBUS Slave Adapter...
- Page 12 Features LED. Indication Description Not used Not Used Ready Green Indicates that the module is On-Line on the fieldbus. Green - Module is On-Line and data exchange is possible. Turned Off - Module is not On-Line Off line Indicates that the module is Off-Line on the fieldbus. Red - Module is Off-Line and no data exchange is possible.
- Page 13 Features LED. Indication Description Diagnostics Fieldbus Diagnostics Indicates certain faults on the Fieldbus side. Flashing Red 1 Hz - Error in configuration: IN and/or OUT length set during initialization of the module is not equal to the length set during configu- ration of the network.
-
Page 14: Specifications
Specifications Specifications Network: PROFIBUS Specification version: Vol. 1: 2.0, Protocol Vol. 2: 2.0 Configuration test version: A-12 Data Rate All baud rates from 9600 bps to 12 Mbps with auto baud rate detection Termination Termination required at the end of the net- work cable.