Page 1 MANUAL DE INSTALAÇÃO E DE FUNCIONAMENTO INSTALLATION AND OPERATION MANUAL INSTALLATIONS- OG BETJENINGSVEJLEDNING MANUAL DE INSTALACIÓN Y FUNCIONAMIENTO INSTALLATIE- EN BEDIENINGSHANDLEIDING INSTALLATIONS- UND BETRIEBSHANDBUCH INSTALLATION- OCH DRIFTHANDBOK MANUEL D’INSTALLATION ET DE FONCTIONNEMENT MANUALE D’INSTALLAZIONE E D’USO ΕΓΧΕΙΡΙΔΙΟ ΕΓΚΑΤΑΣΤΑΣΗΣ ΚΑΙ ΛΕΙΤΟΥΡΓΙΑΣ NETWORK / MODBUS GATEWAYS HC-A(8/16/64)MB / HC-A64NET...
Page 3 Specifikationerna i den här handboken kan ändras utan föregående meddelande för att Hitachi ska kunna leverera de senaste innovationerna till kunderna. Vi på Hitachi gör allt vi kan för att se till att alla specifikationer stämmer, men vi har ingen kontroll över tryckfel och kan därför inte hållas ansvariga för den typen av fel.
Page 4 C A U T I O N This product shall not be mixed with general house waste at the end of its life and it shall be retired according to the appropriated local or national regulations in a environmentally correct way. Due to the refrigerant, oil and other components contained in Air Conditioner, its dismantling must be done by a professio- nal installer according to the applicable regulations.
Page 5 DANGER – Hazards or unsafe practices which COULD result in severe personal injuries or death. PELIGRO – Riesgos o prácticas poco seguras que PODRÍAN producir lesiones personales e incluso la muerte. GEFAHR – Gefährliche oder unsichere Anwendung, die zu schweren Körperverletzungen oder zum Tod führen kann. DANGER –...
Page 6: Table Of Contents
INDEX ÍNDICE 1 PRODUCT GUIDE 1 GUIA DO PRODUTO 2 NEW PRODUCT GENERAL DATA 2 DADOS GERAIS DO PRODUTO NOVO 3 INSTALLATION 3 INSTALAÇÃO 4 ELECTRICAL WIRING 4 LIGAÇÕES ELÉTRICAS 5 OPERATION 5 FUNCIONAMENTO 6 NET CONFIGURATION KIT 6 JOGO DE CONFIGURAÇÃO DA REDE ÍNDICE INDEKS 1 GUÍA DEL PRODUCTO...
Page 7: Product Guide
Interface Controller Control Dash separation H-LINK II Compatible Maxim Number of Controllable Units (8/16/64) MB: Modbus gateway NET: Gateway for CSNET Manager 1.2 MODELS DESCRIPTION HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 ACCESSORY LIST DESCRIPTION Net configuration kit PMML0351A rev.4 - 04/2020...
Page 8: New Product General Data
Max. 100 m according IEEE 802.3 H-LINK Item Specifications HC-A(16/64)MB: SET FREE, UTOPIA, CENTRIFUGAL and HEATING systems Communication with HC-A8MB and HC-A64NET: SET FREE, UTOPIA and CENTRIFUGAL systems Communication line Twisted pair shielded cable, non-polarity Communication system Half-duplex Communication method Asynchronous...
Page 9: Installation
INSTALLATION 3 INSTALLATION 3.1 SAFETY SUMMARY D A N G E R • Read carefully this manual before performing the installation work. • Do not install this device in places accessible to the general public. Install it in electrical enclosures, which are only accessible by the usage of a tool and also provide protection to eventual electromagnetic disturbances. • Do not connect power supply before the device installation is correctly done. Always disconnect power supply from the device before any maintenance or servicing action. C A U T I O N • This appliance must be used only by adult and capable people, having received the technical information or instructions to handle properly and safely this appliance. • This is a Class A product. In a domestic environment this product may cause radio interferences in which case the user may be required to take adequate measures. • Children should be supervised to ensure that they do not play with the appliance. • Check to ensure that the field supplied electrical components (mains power switches, circuit breakers, wires, connectors and wire terminals) have been properly selected according to the electrical data indicated on this document and they comply with national and local codes. If it is necessary, contact with your local authority in regards to standards, rules, regulations, etc. • Do not install Network / Modbus gateways in places: - where any vapor, oil or other dispersed liquids could affect the device.
Page 10  HC-A(8/16/64)MB: Modbus TCP  HC-A64NET : TCP/IP RS485  Modbus RTU for HC-A(8/16/64)MB Not available for HC-A64NET H-LINK Communication bus with Hitachi  units  Operation led indicator Rail DIN 35 mm for assembly inside the  electrical box 3.5 INSTALLATION SPACE...
Page 11 INSTALLATION 3.6 INSTALLATION PROCEDURE D A N G E R • Do not install this device in places accessible to the general pub- • Any unit that is not connected or is not under power when turning on lic. Install it in enclosures or other places which are accessible Network / Modbus gateways, will not be recognized and will have to only by the usage of a tool. be configured later. • Do not connect power supply before the device installation is - Before power supply and turning on the Network / Modbus correctly done. Always disconnect power supply from the device gateways, you must ensure that: before any maintenance or servicing action ¡ 1. All circuits to be connected are correctly applied. ¡ 2. All H-Link connections have been set up. ¡ 3. Modbus connection has been properly done. C A U T I O N •...
Page 12 INSTALLATION Configuration through Ethernet port 1 Connect the Network device to a computer by a ethernet cable (field supplied or available with either the Net Configuration Kit or the CSNET MANAGER) 2 Input the following parameters: • IP Address: 192.168.0.4 •...
Page 13 INSTALLATION “Network information” When the network device is integrated to the LAN / Modbus net by Ethernet, configure the following parameters: • IP Address: Allow to modify the IP of the Network device port (“192.168.0.4” by default). • Mask: Ask to your IT technician for the proper value (“255.255.255.0” by default). •...
Page 14: Electrical Wiring
SW1-2: Not used (keep always “ON”) N O T E (*)No applicable to HC-A64NET. 5 OPERATION 5.1 COMPATIBILITY These devices are not compatible with any of the following Hitachi controllers: - Centralised remote controls - Building air conditioning controls(*) - Other Hitachi BMS Gateways (LONWORKS, BACNET, KNX, FIDELIO) - Other Hitachi MODBUS Gateways - Other units of the same model N O T E (*)HC-A64NET is compatible with CSNET Manager.
Page 15 OPERATION 5.2 INDOOR UNITS 5.2.1 Available data for HC-A(8/16/64)MB Offset (1) Description Values Read/Write 0: No exist Exist Read 1: Exist System address 0~63 Read Unit address 0: Stop On/Off setting order Read/Write 1: Run 0: Cool 1: Dry Mode setting order 2: Fan Read/Write 3: Heat...
Page 16 OPERATION Offset (1) Description Values Read/Write 0: OFF 1: Thermo OFF Unit operation condition Read 2: Thermo ON 3: Alarm (Not used) (Not used) (Not used) Ambient temperature (2) -63ºC ~ 63ºC Read Remote control switch temperature -63ºC ~ 63ºC Read (only when available in the unit) (2) b0: 0 Master/1Slave...
Page 17 OPERATION 5.2.2 Available Data for HC-A(16/64)MB Availability Offset Description Values Read/Write 0: No exist Exist Read 1: Exist System address H-LINK 1: 0~15 Read Unit address H-LINK 2: 0~63 Type 0: Indoor Unit Read 0: Stop On/Off setting order Read/Write 1: Run 0: Cool 1: Dry...
Page 18 OPERATION Availability Offset Description Values Read/Write Temperature setting with 0.5°C inter- ºC x10 (19.5ºC read as Read vals status 195) Heating temperature setting for AUTO ºC Read Cool/Heat status Heating Temperature setting for AUTO ºC x 10 (19.5ºC read Read Cool/heat with 0.5°C intervals status as 195) Cooling Temperature setting for AUTO...
Page 19 OPERATION Availability Offset Description Values Read/Write Control Circuit 1: Water heating Fix 0~80 Read/Write Setting Temp Control Circuit 1: Water cooling Fix 0~80 Read/Write Setting Temp 0: ECO Control Circuit 1: Eco mode Read/Write 1: Comfort Control Circuit 1: Heat ECO Offset 1~10 Read/Write Temperature...
Page 20 OPERATION Availability Offset Description Values Read/Write Control AntiLegionella Setting Tem- 0~80 Read/Write perature 0: No Control Block menu Read/Write 1: Block (user cannot access the menu) 0: Normal Operation Control Yutaki Forced OFF Read/Write 1: Forced OFF 0: Normal Operation Space Heating Heater Forced OFF Read/Write 1: Heater Forced OFF...
Page 21 OPERATION Availability Offset Description Values Read/Write Status Circuit 2: Water heating Fix 0~80 Read Setting Temp Status Circuit 2: Water cooling Fix 0~80 Read Setting Temp 0: ECO Status Circuit 2: Eco mode Read 1: Comfort Status Circuit 1: Heat ECO Offset 1~10 Read Temperature...
Page 22 OPERATION Availability Offset Description Values Read/Write b0: Zone 1 Heating Available b1: Zone 2 Heating Available b2: Zone 1 Cooling Available b3: Zone 2 Cooling Available b4: DHWT Available b5: SWP Available System Configuration b6: Room thermostat Read available Zone 1 b7: Room thermostat available Zone 2 b8: Wireless Setting C1...
Page 23 OPERATION Availability Offset Description Values Read/Write Ta2: Second Ambient Temperature -80~100 Read (inst) Ta2av: Second Ambient Temperature -80~100 (avg) O2: Water outlet Temp 2 (Two2) -80~100 Read O3: Water outlet Temp 3 (Two3) -80~100 Read Tg: Gas Temperature (THMg) -80~100 Read Tl: Liquid Temperature (THMl) -80~100...
Page 24 OPERATION Availability Offset Description Values Read/Write R134 Stop Code Read 179~ Reserved YCC - Enabled Units Read YCC - Working Units Read YCC - Required Units Read N O T E • Register address is calculated as: 5000+(Modbus_Id*200)+offset • Modbus_Id as configured by configuration software • For VRF / Package units, only the relevant data are available (heating units registers will not give any value). The situation is the same for heating units (registers related to air/air units will not give any value). • Availability: PAC: VRF and package units.
Page 25 OPERATION Offset Description Values Read/Write 0: Not possible Power Control Possible Read 1: Possible N O T E • Register address is calculated as: 5000+(Modbus_Id*200)+offset • Modbus_Id as configured by configuration software 5.4 OPTIONAL FUNCTIONS Some optional functions of the indoor units have been added so that they can be managed from the BMS. Offset Description Values...
Page 26: Net Configuration Kit
Shut down the device power supply and restore it after 5 s. If LED2 is still flickering contact to LED2 is flickering Abnormal operation the Hitachi customer service 6 NET CONFIGURATION KIT This accessory provides all the necessary cables for Hitachi installers when commissioning a Modbus installation. Components List: USB cable Ethernet crossed cable USB Pen drive Memory The USB Pen Drive Memory includes a software tool for Modbus communication check when commissioning.
Page 27: Guía Del Producto
Guión de separación Compatible con H-LINK II Número máximo de unidades controlables (8/16/64) MB: gateway Modbus NET: gateway para CSNET Manager 1.2 MODELOS DESCRIPCIÓN HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 LISTA DE ACCESORIOS DESCRIPCIÓN Kit de configuración de la red PMML0351A rev.4 - 04/2020...
Page 28: Datos Generales Del Nuevo Producto
H-LINK Elemento Especificaciones HC-A(16/64)MB: sistemas SET FREE, UTOPIA, CENTRIFUGAL y sistemas de CALEFACCIÓN Comunicación con HC-A8MB y HC-A64NET: sistemas SET FREE, UTOPIA y CENTRIFUGAL Línea de comunicación Cable de par trenzado blindado, no polarizado Sistema de comunicaciones Semidúplex Método de comunicación Asíncrono...
Page 29: Instalación
INSTALACIÓN 3 INSTALACIÓN 3.1 RESUMEN DE SEGURIDAD P E L I G R O • Lea atentamente este manual antes de realizar cualquier trabajo de instalación. • No instale este dispositivo en lugares a los que pueda acceder el público general. Instálelo en armarios eléctricos accesibles solo me- diante el uso de una herramienta y protéjalo frente a eventuales perturbaciones electromagnéticas. • Asegúrese de haber instalado correctamente el dispositivo antes de conectar la alimentación eléctrica. Desconecte siempre la aliment- ación eléctrica antes de realizar cualquier trabajo de mantenimiento en el dispositivo. P R E C A U C I Ó N • Este dispositivo debe ser utilizado únicamente por un adulto o por una persona responsable que haya recibido formación o instrucciones técnicas de cómo manipularlo de forma adecuada y segura. • Este es un producto de Clase A. En un ambiente doméstico, este dispositivo puede provocar interferencias de radio, en cuyo caso el usuario deberá tomar las medidas adecuadas. • Es preciso vigilar a los niños para que no jueguen con el dispositivo. •...
Page 30 RS485  Modbus RTU para HC-A(8/16/64)MB No disponible para HC-A64NET Bus de comunicaciones H-LINK con  unidades Hitachi  Led indicador de funcionamiento Rail DIN 35 mm para montaje en el interior  de la caja eléctrica 3.5 ESPACIO DE INSTALACIÓN Para que el dispositivo funcione correctamente mantenga libre la zona sombreada.
Page 31 INSTALACIÓN 3.6 PROCEDIMIENTO DE INSTALACIÓN P E L I G R O • No instale este dispositivo en lugares a los que pueda acceder el • Cualquier unidad no conectada o que no reciba alimentación cuando público general. Instálelo en lugares cerrados a los que solo se arranque las gateways de red / Modbus no será reconocida y deberá pueda acceder con llave. configurarse posteriormente. • Asegúrese de haber instalado correctamente el dispositivo an- - Antes de alimentar y arrancar las gateways de red / Modbus, tes de conectar la alimentación eléctrica. Desconecte siempre la asegúrese de que: alimentación eléctrica antes de realizar cualquier trabajo de man- ¡ 1. Todos los circuitos están correctamente conectados. tenimiento o reparación en el dispositivo. ¡ 2. Se han realizado todas las conexiones H-Link. ¡ 3. Se ha conectado correctamente el Modbus. P R E C A U C I Ó...
Page 32 INSTALACIÓN Configuración a través de un puerto Ethernet 1 Conecte el dispositivo de red a un ordenador mediante el cable ethernet (suministrado por el instalador o disponible con el kit de configuración de red o bien con el CSNET MANAGER) 2 Introduzca los siguientes parámetros: •...
Page 33 INSTALACIÓN “Información de red” Si el dispositivo de red está integrado en una red LAN / Modbus a través de Ethernet, configure los siguientes parámetros: • Dirección IP: permite modificar la IP del puerto del dispositivo de red (“192.168.0.4” de forma predeterminada). •...
Page 34: Cableado Eléctrico
SW1-2: No se utiliza (mantener siempre en "ON") N O TA (*) No aplica para el HC-A64NET. 5 FUNCIONAMIENTO 5.1 COMPATIBILIDAD Estos dispositivos no son compatibles con ninguno de los siguientes controladores de Hitachi: - Mandos a distancia centralizados - Controles del aire acondicionado de edificios (*) - Otros gateways BMS de Hitachi (LONWORKS, BACNET, KNX, FIDELIO) - Otros gateways MODBUS de Hitachi - Otras unidades del mismo modelo N O TA (*) El HC-A64NET es compatible con CSNET Manager.
Page 35 FUNCIONAMIENTO 5.2 UNIDADES INTERIORES 5.2.1 Datos disponibles para HC-A(8/16/64)MB Offset (1) Nombre Descripción Valores Lectura/escritura 0: No existe EXIST Existe Lectura 1: Existe SYSTEM_ADDRESS Dirección del sistema 0~63 Lectura UNIT_ADDRESS Dirección de la unidad 0: Paro SET_ONOFF Orden de ajuste de marcha/paro Lectura/escritura 1: Marcha 0: Frío...
Page 36 FUNCIONAMIENTO Offset (1) Nombre Descripción Valores Lectura/escritura (no se utiliza) (no se utiliza) (no se utiliza) (no se utiliza) AMBIENT Temperatura ambiente (2) -63ºC ~ 63ºC Lectura TEMPERATURE Temperatura del mando a distancia (solo si está RCS_TEM -63ºC ~ 63ºC Lectura disponible en la unidad) (2) b0: 0 Maestro / 1 Esclavo...
Page 37 FUNCIONAMIENTO 5.2.2 Datos disponibles para HC-A(16/64)MB Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador 0: No exist Existe Lectura 1: Exist Dirección del sistema H-LINK 1: 0~15 Lectura Dirección de la unidad H-LINK 2: 0~63 Type 0: Indoor Unit Lectura 0: Stop Orden de ajuste de marcha/paro Lectura/escritura 1: Run...
Page 38 FUNCIONAMIENTO Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador 0: Low 1: Medium Estado del ventilador 2: High Lectura 3: High2 4: Auto ºC (set according to the unit Estado de la temperatura de ajuste Lectura working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as 195) Lectura intervals status...
Page 39 FUNCIONAMIENTO Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador 0: Stop Control de unidad Marcha/Paro Lectura/escritura 1: Run 0: Cool Control de unidad de modo Lectura/escritura 1: Heat 0: Stop Control de circuito 1 de Marcha/Paro Lectura/escritura 1: Run 0: No 1: Points Control de calor.
Page 40 FUNCIONAMIENTO Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador Control Circuit 2: Cool ECO Offset 1~10 Lectura/escritura Temperature Control Circuit 2: External MBS/KNX 0: Not Available Lectura/escritura Thermostat Available 1: Available Control Zone 2: Thermostat Setting 0~65535 Lectura/escritura Control Zone 2: Room Ambient -32667~32667 Lectura/escritura Temperature...
Page 41 FUNCIONAMIENTO Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador Status Circuit 1: Water cooling Fix 0~80 Lectura Setting Temp 0: ECO Estado del circuito 1: modo ECO Lectura 1: Comfort Estado de circuito 1: temperatura de 1~10 Lectura compensación ECO de calefacción Status Circuit 1: Cool ECO Offset 1~10 Lectura...
Page 42 FUNCIONAMIENTO Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador 0: Standard Estado modo de demanda de ACS Lectura 1: High demand Status DHW Temperature -80~100 Lectura 0: Stop Estado piscina Marcha/Paro Lectura 1: Run Status Swim. Pool Setting 0~80 Lectura Temperature Status Swim. Pool Temperature -80~100 Lectura 0: Stop...
Page 43 FUNCIONAMIENTO Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador 0: OFF 1: Cool Demand –OFF 2: Cool Thermo-OFF 3: Cool Thermo-ON 4: Heat Demand-OFF 5: Heat Thermo-OFF Estado de operación Lectura 6: Heat Thermo-ON 7: DHW-OFF 8: DHW-ON 9: SWP-OFF 10: SWP-ON 11: Alarm Tº...
Page 44 FUNCIONAMIENTO Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador 0: Yutaki S 1: Yutaki SC 2: Yutaki S80 Modelo de unidad 3: Yutaki M Lectura 4: Yutaki SC Lite (New) 5: Yutampo (New) 6: YCC (New) Th: Water Temp Setting (Ttwo) -80~100 Lectura Caudal de agua Water Flow [0.1m3/h]...
Page 45 FUNCIONAMIENTO Disponibilidad Offset Descripción Valores Lectura/escritura Adaptador YCC - Required Units Lectura N O T E • Register address is calculated as: 5000+(Modbus_Id*200)+offset • Modbus_Id as configured by configuration software • For VRF / Package units, only the relevant data are available (heating units registers will not give any value). The situation is the same for heating units (registers related to air/air units will not give any value). • Availability: PAC: VRF and package units. RAC: Domestic units connected to the H-link via PSC-6RAD or SPX-RAMHLK ATW: Air to water units.
Page 46 FUNCIONAMIENTO 5.3 UNIDADES EXTERIORES Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Descripción Valores Lectura/escritura Temperatura del aire exterior -63 °C ~ 63 °C Lectura Compressor Discharge Temperature...
Page 47 FUNCIONAMIENTO 5.4 FUNCIONES OPCIONALES Some optional functions of the indoor units have been added so that they can be managed from the BMS. Offset Descripción Valores Lectura/escritura b1 (Heating temperature compensation) Lectura/escritura b2 (Circulation function at heating Thermo-OFF) Lectura/escritura b4 (Change of filter cleaning period) Lectura/escritura c5 (Static pressure selection) Lectura/escritura...
Page 48: Kit De Configuración De La Red
Hitachi. 6 KIT DE CONFIGURACIÓN DE LA RED Este accesorio proporciona al instalador de Hitachi todos los cables necesarios para poner en marcha la instalación del Modbus. Lista de componentes:...
Page 49: Produktübersicht
PRODUKTÜBERSICHT 1 PRODUKTÜBERSICHT 1.1 KLASSIFIZIERUNG DER GERÄTE Interface Fernbedienungssteuerung Armaturenbrett-Trennung H-LINK II Kompatibel Maximale Anzahl der steuerbaren Geräte (8/16/64) MB: Modbus-Gateway NET: Gateway für CSNET-Manager 1.2 MODELLE BESCHREIBUNG HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 ZUBEHÖR-LISTE BESCHREIBUNG Netzkonfigurationsset PMML0351A rev.4 - 04/2020...
Page 50: Allgemeine Daten Des Neuen Produkts
Länge Max. 100 m gemäß IEEE 802.3 H-LINK Element Spezifikationen HC-A(16/64)MB: SET FREE-, UTOPIA-, CENTRIFUGAL- und HEATING-Systeme Kommunikation mit HC-A8MB und HC-A64NET: SET FREE-, UTOPIA- und CENTRIFUGAL-Systeme Kommunikationsleitung Abgeschirmtes Torsionskabel, ohne Polarität Kommunikationssystem Halbduplex Kommunikationsmethode Asynchron Übertragungsgeschwindigkeit 9600 Bauds Kabellänge...
Page 51: Installation
INSTALLATION 3 INSTALLATION 3.1 SICHERHEITSÜBERSICHT G E FA H R • Lesen Sie dieses Handbuch vor der Installation sorgfältig durch. • Achten Sie darauf, dass Kinder nicht mit dem Gerät spielen. • Dieses Gerät darf nicht öffentlich zugänglich sein. Montieren • Vergewissern Sie sich, dass die vor Ort beschafften elektrischen Sie es bitte in einem Schaltschrank, der nur mithilfe von einem Komponenten (Netzschalter, Stromkreisunterbrecher, Kabel, Stecker Werkzeug geöffnet werden kann und außerdem Schutz bei elek- und Kabelanschlüsse) gemäß den angegebenen elektrischen Daten...
Page 52  RS485  Modbus RTU für HC-A(8/16/64)MB Nicht verfügbar für HC-A64NET H-LINK-Kommunikationsbus mit  Hitachi-Geräten  LED-Betriebsanzeige Schiene DIN 35 mm für den  Zusammenbau innerhalb des Schaltkastens 3.5 INSTALLATIONSRAUM Halten Sie den grauen Bereich für den korrekten Betrieb des Geräts frei.
Page 53 INSTALLATION 3.6 INSTALLATIONSSCHRITTE G E FA H R • Dieses Gerät muss an Orten installiert werden, die für die Öffen- • Geräte, die beim Einschalten der Netzwerk-/Modbus-Gateways nicht tlichkeit unzugänglich sind. Installieren Sie es in Gehäusen oder angeschlossen oder mit Strom versorgt sind, werden nicht erkannt und an anderen Stellen, die nur mit einem Werkzeug zugänglich sind. müssen später konfiguriert werden. • Erst nach der korrekten Geräteinstallation die Stromversorgung - Bevor Sie die Stromversorgung und die Netzwerk-/ Modbus- anschließen. Trennen Sie vor allen Wartungs- und Instandset- Gateways einschalten, müssen Sie sicher stellen, dass: zungsarbeiten das Stromversorgungskabel vom Gerät. ¡ 1. Alle anzuschließenden Kreisläufe sind korrekt verbunden. ¡ 2. Alle H-Link-Verbindungen wurden eingerichtet. ¡ 3. Der Modbus-Anschluss wurde korrekt ausgeführt. V O R S I C H T •...
Page 54 INSTALLATION Konfiguration über Ethernet-Port 1 Schließen Sie das Netzwerkgerät mit dem Ethernet-Kabel an den Computer an (Feld geliefert oder zur Verfügung mit dem Netzkonfigurationsset oder auch mit dem CSNET MANAGER) 2 Eingabe der folgenden Parameter: • IP-Adresse: 192.168.0.4 • Port: Modbus Gateway/ HC-A64NET 3 Drücken Sie das Schaltfeld am Bildschirm...
Page 55 INSTALLATION “Netzwerk-Information” Wenn das Netzwerkgerät über Ethernet in LAN/Modbus integriert ist, konfigurieren Sie folgende Parameter: • IP-Adresse: Ermöglichen Sie die Modifizierung der IP des Netzwerkgeräte-Ports (standardmäßig “192.168.0.4). • Maske: Fragen Sie Ihren IT-Techniker nach dem entsprechenden Wert. (standardmäßig “255.255.255.0”). • Gateway: LAN-Gateway-Adresse (standardmäßig “192.168.0.1”).
Page 56: Kabelanschluss
SW1-2: Nicht verwendet (immer auf “ON” stellen) H I N W E I S (*) Nicht anwendbar bei HC-A64NET. 5 BETRIEB 5.1 KOMPATIBILITÄT Diese Geräte sind mit keiner der folgenden Hitachi-steuerungen kompatibel: - Zentralisierte Fernbedienungen - Steuerungen zur Klimatisierung von Gebäuden (*) - Andere Hitachi-BMS-Gateways (LONWORKS, BACNET, KNX, FIDELIO) - Andere Hitachi-MODBUS-Gateways - Andere Einheiten des gleichen Modells H I N W E I S (*) HC-A64NET ist mit dem CSNET Manager kompatibel.
Page 57 BETRIEB 5.2 INNENEINHEITEN 5.2.1 Verfügbare daten für HC-A(8/16/64)MB Offset (1) Name Beschreibung Werte Lesen/Schreiben 0: Existiert nicht EXIST Existiert Lesen 1: Existiert SYSTEM_ADDRESS Systemadresse UNIT_ 0~63 Lesen Geräteadresse ADDRESS 0: Aus Ein/Aus- SET_ONOFF Lesen/Schreiben Einstellbefehl 1: Ein 0: Kühlen 1: Entfeuchten SET_MODE Befehl Betriebsarteinstellung 2: Lüfter...
Page 58 BETRIEB Offset (1) Name Beschreibung Werte Lesen/Schreiben Expansions-ventilöffnung des VALVE_OPEN 0~100 (Nicht verwendet) Innengeräts 0: OFF 1: Thermo OFF OPER_CONDITION Gerätebetriebszustand Lesen 2: Thermo ON 3: Alarm (Nicht (Nicht verwendet) (Nicht verwendet) (Nicht verwendet) verwendet) AMBIENT Umgebungstemperatur (2) -63ºC ~ 63ºC Lesen TEMPERATURE Fernbedienungs-...
Page 59 BETRIEB 5.2.3 Verfügbare daten für HC-A(16/64)MB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- 0: No exist Existiert Lesen 1: Exist Systemadresse H-LINK 1: 0~15 Lesen Geräteadresse H-LINK 2: 0~63 Type 0: Indoor Unit Lesen 0: Stop Ein/Aus-Einstellbefehl Lesen/Schreiben 1: Run 0: Cool 1: Dry Befehl Betriebsarteinstellung 2: Fan...
Page 60 BETRIEB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- 0: Low 1: Medium Lüfter-Status 2: High Lesen 3: High2 4: Auto ºC (set according to the Temperatureinstellungsstatus Lesen unit working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as Lesen intervals status 195) Heating temperature setting for AUTO ºC...
Page 61 BETRIEB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- b0: Input 1 open/close b1: Input 2 open/close b2: Enabled/Disabled CN3 Configuration status Lesen (Indicates if the unit has CN3 enabled with any function) 38~49 Reserviert 0: Stop Steuergerät Start/Stopp Lesen/Schreiben 1: Run 0: Cool Steuergeräte-Modus Lesen/Schreiben...
Page 62 BETRIEB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- Control Circuit 2: Water cooling Fix 0~80 Lesen/Schreiben Setting Temp 0: ECO Control Circuit 2: Eco mode Lesen/Schreiben 1: Comfort Control Circuit 2: Heat ECO Offset 1~10 Lesen/Schreiben Temperature Control Circuit 2: Cool ECO Offset 1~10 Lesen/Schreiben Temperature...
Page 63 BETRIEB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- 0: No 1: Points Status Heat. OTC 1 Lesen 2: Gradient 3: Fix 0: No Status Cool. OTC 1 1: Points Lesen 2: Fix Status Circuit 1: Water heating Fix 0~80 Lesen Setting Temp Status Circuit 1: Water cooling Fix 0~80 Lesen...
Page 64 BETRIEB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- Status Circuit 2: Wireless Setting 50~350 (5,0~35,0) Lesen Temperature Status Circuit 2: Wireless Room 0~1000 (0,0~100,0) Lesen temperature 0: Stop Wärmewasserspeicherstatus Start/ Lesen Stopp 1: Run Wärmewasserspeicherstatus 0~80 Lesen Einstelltemperatur 0: Disable Status DHW Boost Lesen 1: Enable Reserviert...
Page 65 BETRIEB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- b0: Zone 1 Heating Available b1: Zone 2 Heating Available b2: Zone 1 Cooling Available b3: Zone 2 Cooling Available b4: DHWT Available b5: SWP Available Systemkonfiguration b6: Room thermostat Lesen available Zone 1 b7: Room thermostat available Zone 2 b8: Wireless Setting C1...
Page 66 BETRIEB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- LCD-Software Lesen Geräteleistung Lesen Unit Power Consumption Lesen 0~100 Nur für YUTAKI S Water Outler HP (TwoHP) Lesen & S Combi Ta1av: Outdoor Unit Ambient Average -80~100 Lesen Temperature Ta2: Second Ambient Temperature -80~100 Lesen (inst)
Page 67 BETRIEB Verfügbarkeit Offset Beschreibung Werte Lesen/Schreiben RAC- 0: Alarm Alarmnummer Lesen XXX: Alarm number R134a Abgastemperatur Lesen R134a Ansaugtemperatur Lesen R134a Ausströmdruck Lesen R134a Ansaugdruck Lesen R134a Kompressorfrequenz Lesen R134a Innen-Expansionsventilöffnung Lesen R134a Wert des Kompressorstroms Lesen R134a Wiederholungscode Lesen R134 Te SH Lesen R134 Secondary Current...
Page 68 BETRIEB 5.3 AUSSENGERÄTE Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Beschreibung Werte Lesen/Schreiben Außenlufttemperatur -63ºC ~ 63ºC Lesen Compressor Discharge Temperature 0 ~ 200 ºC...
Page 69 BETRIEB 5.4 OPTIONALE FUNKTIONEN Some optional functions of the indoor units have been added so that they can be managed from the BMS. Offset Beschreibung Werte Lesen/Schreiben b1 (Heating temperature compensation) Lesen/Schreiben b2 (Circulation function at heating Thermo-OFF) Lesen/Schreiben b4 (Change of filter cleaning period) Lesen/Schreiben c5 (Static pressure selection) Lesen/Schreiben...
Page 70: Netzkonfigurationsset
Schalten Sie die Stromversorgung des Geräts ab und stellen Sie sie nach 5 s wieder her. LED2 flackert Anormaler Betrieb Wenn LED2 noch immer flackert, setzen Sie sich mit dem Hitachi-Kundendienst in Verbindung. 6 NETZKONFIGURATIONSSET Dieses Zubehör bietet alle notwendigen Kabel für Hitachi-Installateure, wenn eine Modbus-Installation in Betrieb genommen wird. Teileliste: USB-Kabel Gekreuztes Ethernet-Kabel USB-Pen-Drive-Memory Die USB-Pen-Drive-Memory enthält ein Software-Tool für die Prüfung der Modbus-Kommunikation bei der Inbetriebnahme.
Page 71: Guide Du Produit
Tiret de séparation Compatible H-LINK II Nombre maximum d'unités contrôlables (8/16/64) MB : gateway Modbus NET : gateway pour CSNET Manager 1.2 MODÈLES DESCRIPTION HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 LISTE D'ACCESSOIRES DESCRIPTION Kit de configuration réseau PMML0351A rev.4 - 04/2020...
Page 72: Caractéristiques Générales De Nouveau Produit
H-LINK Élément Spécifications HC-A(16/64)MB: systèmes FREE SET, UTOPIA, CENTRIFUGAL et HEATING Communication avec HC-A8MB et HC-A64NET: systèmes SET FREE, UTOPIA et CENTRIFUGAL Ligne de communication Câble blindé à paire torsadée, sans polarité Système de communication Semi-duplex Méthode de communication...
Page 73: Installation
INSTALLATION 3 INSTALLATION 3.1 CONSIGNES DE SÉCURITÉ D A N G E R • Veuillez lire ce manuel soigneusement avant de réaliser les • Les enfants doivent être surveillés pour s'assurer qu'ils ne jouent pas travaux d'installation. avec l'appareil. • N’installez pas ce système dans des endroits accessibles au • Assurez-vous que les composants électriques fournis sur site (inter- grand public. Installez-le dans des coffrets électriques, unique- rupteurs d'alimentation principale, disjoncteurs, câbles, connecteurs ment accessibles à l’aide d’un outil et protégez-le contre de po-...
Page 74  RS485  Modbus RTU pour HC-A(8/16/64)MB Non disponible pour HC-A64NET Bus de communication H-LINK avec  unités Hitachi  LED d'indication de fonctionnement Rail DIN 35 mm pour montage dans coffret  électrique 3.5 ESPACE D'INSTALLATION Maintenez la zone grise libre pour le bon fonctionnement du dispositif.
Page 75 INSTALLATION 3.6 PROCÉDURE D’INSTALLATION D A N G E R • N'installez pas ce dispositif dans des endroits accessibles au • Toute unité non connectée ou non alimentée au moment du démar- grand public. Installez-le dans un coffret ou un lieu uniquement rage des gateways Réseau / Modbus ne sera pas reconnue et devra accessible à l'aide d'un outil. être configurée ultérieurement. • Ne connectez pas la source d’alimentation avant d'avoir cor- - Avant d'activer la source d’alimentation et d'allumer les gateways rectement terminé l'installation. Déconnectez toujours la source Réseau / Modbus , vous devez vous assurer que :...
Page 76 INSTALLATION Configuration via port Ethernet 1 Connectez le dispositif de réseau à un ordinateur via un câble Ethernet (fourni sur site ou disponible avec le kit de configuration réseau ou avec le CSNET MANAGER) 2 Saisissez les paramètres suivants : •...
Page 77 INSTALLATION « Informations de réseau » • Quand le dispositif de réseau est intégré à la LAN / au Modbus via Ethernet, configurez les paramètres suivants : • Adresse IP : permettez de modifier l’IP du port du dispositif de réseau («192.168.0.4» par défaut). •...
Page 78: Câblage Électrique
SW1-2 : non utilisé (toujours sur « ON ») R E M A R Q U E (*) Non applicable pour HC-A64NET. 5 FONCTIONNEMENT 5.1 COMPATIBILITÉ Ces dispositifs ne sont compatibles avec aucun des contrôleurs Hitachi ci-dessous : - Télécommandes centralisés - Contrôles de conditionnement d’air de bâtiment (*1) - Autres gateways BMS Hitachi (LONWORKS, BACNET, KNX, FIDELIO) - Autres gateways MODBUS Hitachi - Autres unités du même modèle R E M A R Q U E (*) HC-A64NET est compatible avec CSNET Manager.
Page 79 FONCTIONNEMENT 5.2 UNITÉS INTÉRIEURES 5.2.1 Données disponibles pour HC-A(8/16/64)MB Offset Description Valeurs Lecture/Écriture 0 : n’existe pas EXIST Existe Lecture 1 : existe SYSTEM_ADDRESS Adresse du système 0~63 Lecture UNIT_ADDRESS Adresse de l'unité 0 : arrêt Réglage SET_ONOFF Lecture/Écriture marche/arrêt 1 : marche 0 : froid 1 : déshumidification...
Page 80 FONCTIONNEMENT Offset Description Valeurs Lecture/Écriture 0 : OFF 1 : Thermo-OFF OPER_CONDITION Conditions de fonctionnement de l'unité Lecture 2 : Thermo-ON 3 : Alarme (Non utilisé) (Non utilisé) (Non utilisé) (Non utilisé) AMBIENT Température ambiante (2) -63ºC ~ 63ºC Lecture TEMPERATURE Télécommande change la temp.
Page 81 FONCTIONNEMENT 5.2.2 Données disponibles pour HC-A(16/64)MB Disponibilité Offset Description Valeurs Lecture/Écriture 0: No exist Existe Lecture 1: Exist Adresse du système H-LINK 1: 0~15 Lecture Adresse de l'unité H-LINK 2: 0~63 Type 0: Indoor Unit Lecture 0: Stop Réglage marche/arrêt Lecture/Écriture 1: Run 0: Cool...
Page 82 FONCTIONNEMENT Disponibilité Offset Description Valeurs Lecture/Écriture 0: Low 1: Medium État du ventilateur 2: High Lecture 3: High2 4: Auto ºC (set according to the État de la température de consigne Lecture unit working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as Lecture intervals status 195)
Page 83 FONCTIONNEMENT Disponibilité Offset Description Valeurs Lecture/Écriture b0: Input 1 open/close b1: Input 2 open/close b2: Enabled/Disabled CN3 Configuration status Lecture (Indicates if the unit has CN3 enabled with any function) 38~49 Réservées 0: Stop Contrôle d'unité Marche/Arrêt Lecture/Écriture 1: Run 0: Cool Contrôle d'unité...
Page 84 FONCTIONNEMENT Disponibilité Offset Description Valeurs Lecture/Écriture Control Circuit 2: Water cooling Fix 0~80 Lecture/Écriture Setting Temp 0: ECO Control Circuit 2: Eco mode Lecture/Écriture 1: Comfort Control Circuit 2: Heat ECO Offset 1~10 Lecture/Écriture Temperature Control Circuit 2: Cool ECO Offset 1~10 Lecture/Écriture Temperature...
Page 85 FONCTIONNEMENT Disponibilité Offset Description Valeurs Lecture/Écriture 0: No 1: Points Status Heat. OTC 1 Lecture 2: Gradient 3: Fix 0: No Status Cool. OTC 1 1: Points Lecture 2: Fix Status Circuit 1: Water heating Fix 0~80 Lecture Setting Temp Status Circuit 1: Water cooling Fix 0~80 Lecture...
Page 86 FONCTIONNEMENT Disponibilité Offset Description Valeurs Lecture/Écriture Status Circuit 2: Wireless Setting 50~350 (5,0~35,0) Lecture Temperature Status Circuit 2: Wireless Room 0~1000 (0,0~100,0) Lecture temperature 0: Stop État ballon ECS Marche/Arrêt Lecture 1: Run État température consigne ballon ECS 0~80 Lecture 0: Disable Status DHW Boost Lecture...
Page 87 FONCTIONNEMENT Disponibilité Offset Description Valeurs Lecture/Écriture b0: Zone 1 Heating Available b1: Zone 2 Heating Available b2: Zone 1 Cooling Available b3: Zone 2 Cooling Available b4: DHWT Available b5: SWP Available Configuration système b6: Room thermostat Lecture available Zone 1 b7: Room thermostat available Zone 2 b8: Wireless Setting C1...
Page 88 FONCTIONNEMENT Disponibilité Offset Description Valeurs Lecture/Écriture Logiciel de LCD Lecture Puissance de l’unité Lecture Unit Power Consumption Lecture 0~100 uniquement pour Water Outler HP (TwoHP) Lecture YUTAKI S et S Combi Ta1av: Outdoor Unit Ambient Average -80~100 Lecture Temperature Ta2: Second Ambient Temperature -80~100 Lecture (inst)
Page 89 FONCTIONNEMENT Disponibilité Offset Description Valeurs Lecture/Écriture 0: Alarm Numéro d'alarme Lecture XXX: Alarm number Température de refoulement R134a Lecture Température d'aspiration R134a Lecture Pression de refoulement R134a Lecture Pression d'aspiration R134a Lecture Fréquence de compresseur R134a Lecture Ouverture de la soupape de sécurité Lecture intérieur R134a Valeur actuelle du compresseur R134a...
Page 90 FONCTIONNEMENT 5.2.3 Unités extérieures Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Description Valeurs Lecture/Écriture Température de l'air extérieur -63 °C à...
Page 91 5.4 DÉPANNAGE CODE D'ALARME DESCRIPTION CONTRE-MESURE Fonctionnement Éteignez la source d'alimentation du dispositif et rétablissez-la après 5 s. Si la LED2 continue La LED2 clignote anormal de clignoter, contactez le service clientèle d'Hitachi PMML0351A rev.4 - 04/2020...
Page 92: Kit De Configuration Réseau
KIT DE CONFIGURATION RÉSEAU 6 KIT DE CONFIGURATION RÉSEAU Cet accessoire fournit tous les câbles nécessaires pour les installateurs d'Hitachi lors de la mise en service d'une installation Modbus. Liste des composants : Câble USB Câble Ethernet croisé Clé USB La clé...
Page 93: Guida Dei Prodotti
Controllo del dispositivo di controllo di interfaccia Trattino Compatibile con H-LINK II Numero massimo di unità controllabili (8/16/64) MB: Gateway modbus NET: Gateway gestore CSNET 1.2 MODELLI DESCRIZIONE HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 ELENCO DEGLI ACCESSORI DESCRIZIONE Kit configurazione rete PMML0351A rev.4 - 04/2020...
Page 94: Specifiche Generali Del Nuovo Prodotto
Max. 100 m in conformità a IEEE 802.3 H-LINK Elemento Specifiche HC-A(16/64)MB: SET FREE, UTOPIA, CENTRIFUGAL e sistemi di RISCALDAMENTO Comunicazione con HC-A8MB e HC-A64NET: SET FREE, UTOPIA e CENTRIFUGAL Linea di comunicazione Doppino ritorto schermato, senza polarità Sistema di comunicazione Semiduplex Metodo di comunicazione Asincrono Velocità...
Page 95: Installazione
INSTALLAZIONE 3 INSTALLAZIONE 3.1 PRECAUZIONI PER LA SICUREZZA P E R I C O L O • Leggere attentamente il presente manuale prima di eseguire • Mantenere i bambini fuori dalla portata dei dispositivi elettrici. l'installazione. • Accertarsi che i componenti elettrici non in dotazione (interruttori di • Non installare questo dispositivo in un luogo accessibile al pub- alimentazione, interruttori di circuito, cavi, connettori e morsetti) siano blico. Installarlo in involucri per dispositivi elettrici, che siano...
Page 96 Cavo RS485  Modbus RTU per HC-A(8/16/64)MB Non disponibile per HC-A64NET Bus di comunicazione H-LINK con  le unità Hitachi  Indicatore LED di funzionamento Guida DIN 35mm per i collegamenti  all'interno del quadro elettrico 3.5 SPAZIO DI INSTALLAZIONE Mantenere libera l'aria grigia per il corretto funzionamento del dispositivo.
Page 97 INSTALLAZIONE 3.6 PROCEDURA DI INSTALLAZIONE P E R I C O L O • Non installare questa unità in luoghi accessibili al pubblico. In- • Le unità non collegate o che non si trovano sotto tensione nel mo- stallare l'unità all'interno di contenitori o in altri luoghi accessibili mento in cui vengono attivati i gateway Rete / Modbus, non verranno solo attraverso l'utilizzo di uno strumento.
Page 98 INSTALLAZIONE Configurazione attraverso la porta Ethernet 1 Collegare il dispositivo di rete ad un computer attraverso un cavo ethernet (non in dotazione, ma fornito con il kit di configurazione di rete o anche con il CSNET MANAGER) 2 Inserire i seguenti parametri: •...
Page 99 INSTALLAZIONE “Informazioni di rete” Quando il dispositivo di rete è integrato alla rete LAN / Modbus attraverso un cavo Ethernet, configurare i seguenti parametri: • Indirizzo IP: Permettere la modifica dell’IP del dispositivo di rete (“192.168.0.4” di default). • Maschera: Chiedere al proprio tecnico informatico il valore corretto (“255.255.255.0” di default). •...
Page 100: Collegamento Dello Schema Elettrico
SW1 Configurazione SW1-2: Non usato (lasciare sempre “ON”) N O TA (*) Non applicabile al HC-A64NET. 5 FUNZIONAMENTO 5.1 COMPATIBILITÀ Questi dispositivi non sono compatibili con nessuno dei seguenti controller Hitachi: - Controlli remoti centralizzati - Controlli di aria condizionata per edifici (*) - Altri Gateway BMS Hitachi (LONWORKS, BACNET, KNX, FIDELIO) - Altri Gateway MODBUS Hitachi - Altre unità dello stesso modello N O TA (*) HC-A64NET è compatibile con il CSNET MANAGER.
Page 101 FUNZIONAMENTO 5.2 UNITÀ INTERNE 5.2.1 Dati disponibili per HC-A(8/16/64)MB Offset (1) Nome Descrizione Valori Lettura/Scrittura 0: Non esiste EXIST Esiste Lettura 1: Esiste Indirizzo SYSTEM_ADDRESS sistema 0~63 Lettura UNIT_ADDRESS Indirizzo unità 0: Arresto SET_ONOFF Ordine di impostazione avvio/arresto Lettura/Scrittura 1: Avvio 0: Freddo 1: Deumidificazione SET_MODE...
Page 102 FUNZIONAMENTO Offset (1) Nome Descrizione Valori Lettura/Scrittura (Leggere STOP_CAUSE Causa dell’arresto del compressore manuale di Lettura servizio dell'unità) Apertura (non VALVE_OPEN 0~100 della valvola di espansione dell'unità interna utilizzato) 0: OFF 1: Thermo OFF OPER_CONDITION Condizione funzionamento unità Lettura 2: Thermo ON 3: Allarme (non utilizzato) (non utilizzato)
Page 103 FUNZIONAMENTO 5.2.2 Dati disponibili per HC-A(16/64)MB Disponibilità Offset Descrizione Valori Lettura/Scrittura 0: No exist Esiste Lettura 1: Esiste Indirizzo del sistema H-LINK 1: 0~15 Lettura Indirizzo dell'unità H-LINK 2: 0~63 Type 0: Indoor Unit Lettura 0: Arresto Ordine di impostazione avvio/arresto Lettura/Scrittura 1: Avvio 0: Freddo...
Page 104 FUNZIONAMENTO Disponibilità Offset Descrizione Valori Lettura/Scrittura 0: Basso 1: Medio Stato della ventola 2: Alto Lettura 3: High2 4: Auto Stato della temperatura di ºC (set according to the Lettura impostazione unit working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as Lettura intervals status 195)
Page 105 FUNZIONAMENTO Disponibilità Offset Descrizione Valori Lettura/Scrittura b0: Input 1 open/close b1: Input 2 open/close b2: Enabled/Disabled CN3 Configuration status Lettura (Indicates if the unit has CN3 enabled with any function) 38~49 Riservata 0: Arresto Controllo dell'unità Avvio/Arresto Lettura/Scrittura 1: Avvio 0: Freddo Controllo dell'unità...
Page 106 FUNZIONAMENTO Disponibilità Offset Descrizione Valori Lettura/Scrittura Control Circuit 2: Water heating Fix 0~80 Lettura/Scrittura Setting Temp Control Circuit 2: Water cooling Fix 0~80 Lettura/Scrittura Setting Temp 0: ECO Control Circuit 2: Eco mode Lettura/Scrittura 1: Comfort Control Circuit 2: Heat ECO Offset 1~10 Lettura/Scrittura Temperature...
Page 107 FUNZIONAMENTO Disponibilità Offset Descrizione Valori Lettura/Scrittura 0: Arresto Stato del circuito 1 Avvio/Arresto Lettura 1: Avvio 0: No 1: Points Status Heat. OTC 1 Lettura 2: Gradient 3: Fix 0: No Status Cool. OTC 1 1: Points Lettura 2: Fix Status Circuit 1: Water heating Fix 0~80 Lettura...
Page 108 FUNZIONAMENTO Disponibilità Offset Descrizione Valori Lettura/Scrittura Status Circuit 1: Cool ECO Offset 1~10 Lettura Temperature Status Zone 2: Thermostat Setting 50~350 (5,0~35,0) Lettura Status Zone 2: Ambient Temperature 0~1000 (0,0~100,0) Lettura Status Circuit 2: Wireless Setting 50~350 (5,0~35,0) Lettura Temperature Status Circuit 2: Wireless Room 0~1000 (0,0~100,0) Lettura...
Page 109 FUNZIONAMENTO Disponibilità Offset Descrizione Valori Lettura/Scrittura b0: Zone 1 Heating Available b1: Zone 2 Heating Available b2: Zone 1 Cooling Available b3: Zone 2 Cooling Available b4: DHWT Available b5: SWP Available Configurazione sistema b6: Room thermostat Lettura available Zone 1 b7: Room thermostat available Zone 2 b8: Wireless Setting C1...
Page 110 FUNZIONAMENTO Disponibilità Offset Descrizione Valori Lettura/Scrittura Software LCD Lettura Taglia Unità Lettura Unit Power Consumption Lettura 0~100 solo per unità Water Outler HP (TwoHP) Lettura YUTAKI S e S Combi Ta1av: Outdoor Unit Ambient Average -80~100 Lettura Temperature Ta2: Second Ambient Temperature -80~100 Lettura (inst)
Page 111 FUNZIONAMENTO Disponibilità Offset Descrizione Valori Lettura/Scrittura 0: Alarm Numero di allarme: Lettura XXX: Alarm number Temperatura di scarico R134a Lettura Temperatura di aspirazione R134a Lettura Pressione di scarico R134a Lettura Pressione di aspirazione R134a Lettura Frequenza del compressore R134a Lettura Apertura della valvola di espansione Lettura interna R134a...
Page 112 FUNZIONAMENTO 5.3 UNITÀ ESTERNE Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Descrizione Valori Lettura/Scrittura Temperatura dell'aria esterna da -63ºC a 63ºC Lettura Compressor Discharge Temperature...
Page 113 5.6 RISOLUZIONE DEI PROBLEMI CODICE ALLARME DESCRIZIONE CONTROMISURA Funzionamento Scollegare l'alimentazione elettrica del dispositivo e ripristinarla dopo 5 s. Se il LED2 è ancora LED2 lampeggiante anomalo lampeggiante contattare l'assistenza clienti Hitachi PMML0351A rev.4 - 04/2020...
Page 114: Kit Configurazione Rete
KIT CONFIGURAZIONE RETE 6 KIT CONFIGURAZIONE RETE Questo accessorio fornisce tutti i cavi necessari agli installatori di Hitachi al momento della messa in esercizio di una installazione Modbus. Elenco dei componenti: Cavo USB Cavo Ethernet incrociato Memoria pen drive USB La memoria pen drive USB include uno strumento software per la verifica delle comunicazioni Modbus durante la messa in esercizio.
Page 115: Guia Do Produto
Separação com travessão Compatível com H-LINK II Número máximo de unidades controláveis (8/16/64) MB: Gateway Modbus NET: Gateway para CSNET Manager 1.2 NOVOS DESCRIÇÃO HC-A8MB HC-A64MB HC-A64NET 1.3 LISTA DOS ACESSÓRIOS DESCRIÇÃO Jogo de configuração da rede PMML0351A rev.4 - 04/2020...
Page 116: Dados Gerais Do Produto Novo
H-LINK Item Especificações HC-A (16/64) MB: SET FREE, UTOPIA, CENTRIFUGAL e AQUECIMENTO Comunicação com HC-A8MB e HC-A64NET: SET FREE, UTOPIA e CENTRIFUGAL Linha de comunicação Cabo de par torcido blindado, sem polaridade Sistema de comunicação Half-duplex Método de comunicação Assíncrona...
Page 117: Instalação
INSTALAÇÃO 3 INSTALAÇÃO 3.1 RESUMO DA SEGURANÇA P E R I G O • Leia cuidadosamente este manual antes de executar o trabalho • As crianças devem ser vigiadas para garantir que não tocam no eq- de instalação. uipamento. • Não instale este dispositivo em locais acessíveis ao público em • Certifique-se de que os componentes elétricos fornecidos no local (in- geral. Faça a instalação em armários elétricos, acessíveis apenas terruptores de alimentação da rede, disjuntores, cabos, conectores e mediante a utilização de uma ferramenta, e instale também pro- terminais de cabos) foram selecionados corretamente de acordo com teção contra eventuais distúrbios eletromagnéticos. os dados elétricos indicados neste documento e de que cumprem as regulamentações locais e nacionais. Se for necessário, consulte •...
Page 118  RS485  Modbus RTU para HC-A(8/16/64)MB Não disponível para HC-A64NET Bus de comunicação H-LINK com  unidades Hitachi  Indicador LED de funcionamento Calha DIN 35 mm para montagem no  interior da caixa elétrica 3.5 ESPAÇO DE INSTALAÇÃO Mantenha livre a zona cinzenta para um funcionamento correto do dispositivo.
Page 119 INSTALAÇÃO 3.6 PROCEDIMENTO DE INSTALAÇÃO P E R I G O • Não instale este dispositivo em locais acessíveis ao público em • Ao ligar os gateways de rede/Modbus, qualquer unidade que não es- geral. Instale-o em recintos ou outros locais acessíveis unica- teja ligada não será reconhecida e terá que ser configurada posteri- mente mediante a utilização de uma ferramenta. ormente. • Não ligue a fonte de alimentação antes de uma instalação cor- - Antes de ligar a alimentação elétrica dos gateways de rede / reta do dispositivo. Desligue sempre a fonte de alimentação do Modbus, deve certificar-se de que: dispositivo antes de qualquer ação de manutenção ou reparação.
Page 120 INSTALAÇÃO Configuração através de porta Ethernet 1 Ligue o dispositivo de rede a um computador através de um cabo Ethernet (não fornecido, mas disponível com o jogo de configuração da rede ou também com o CSNET MANAGER) 2 Introduza os seguintes parâmetros: •...
Page 121 INSTALAÇÃO “Informação de Rede” Quando o dispositivo de rede estiver integrado na rede LAN / Modbus por Ethernet, configure os seguintes parâmetros: • Endereço IP: permite modificar o IP da porta do dispositivo de rede (“192.168.0.4” por defeito). • Mask: Pergunte ao seu técnico informático o valor correto (“255.255.255.0” por defeito). •...
Page 122: Ligações Elétricas
Configuração SW1-2: Sem utilização (manter sempre “ON”) N O TA (*) Não aplicável a HC-A64NET. 5 FUNCIONAMENTO 5.1 COMPATIBILIDADE Estes dispositivos não são compatíveis com nenhum dos seguintes controladores Hitachi: - Controlos remotos centralizados - Controlos de ar condicionado de edifícios (*) - Outros gateways BMS da Hitachi (LONWORKS, BACNET, KNX, FIDELIO) - Outros gateways MODBUS da Hitachi - Outras unidades do mesmo modelo N O TA (*) HC-A64NET é compatível com CSNET Manager.
Page 123 FUNCIONAMENTO 5.2 UNIDADES INTERIORES 5.2.1 Dados disponíveis para HC-A(8/16/64)MB Offset (1) Nome Descrição Valores Leitura/Gravação 0: Não existe EXIST Existe Leitura 1: Existe SYSTEM_ADDRESS Endereço de sistema 0~63 Leitura UNIT_ADDRESS Endereço de unidade 0: Desligar Ordem de SET_ONOFF Leitura/Gravação ajuste Lig./Des. 1: Ligar 0: Frio 1: Desumidificação...
Page 124 FUNCIONAMENTO Offset (1) Nome Descrição Valores Leitura/Gravação Abertura da (não VALVE_OPEN 0~100 válvula de expansão da unidade interior utilizado) 0: OFF 1: Thermo OFF OPER_CONDITION Condição de funcionamento da unidade Leitura 2: Thermo ON 3: Alarme (não utilizado) (não utilizado) (não utilizado) (não utilizado) AMBIENT...
Page 125 FUNCIONAMENTO 5.2.2 Dados disponíveis para HC-A(16/64)MB Availability Offset Descrição Valores Leitura/Gravação 0: No exist Existe Leitura 1: Exist Endereço de sistema H-LINK 1: 0~15 Leitura Endereço de unidade H-LINK 2: 0~63 Tipo 0: Indoor Unit Leitura 0: Stop Ordem de ajuste On/Off Leitura/Gravação 1: Run 0: Cool...
Page 126 FUNCIONAMENTO Availability Offset Descrição Valores Leitura/Gravação 0: Low 1: Medium Estado do ventilador 2: High Leitura 3: High2 4: Auto ºC (set according to the Estado de ajuste da temperatura Leitura unit working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as Leitura intervals status 195)
Page 127 FUNCIONAMENTO Availability Offset Descrição Valores Leitura/Gravação 38~49 Reservado 0: Stop Controlo de unidade Ligar/Parar Leitura/Gravação 1: Run 0: Cool Controlo de unidade de modo Leitura/Gravação 1: Heat 0: Stop Controlo de circuito 1 Ligar/Parar Leitura/Gravação 1: Run 0: No 1: Points Control Heat.
Page 128 FUNCIONAMENTO Availability Offset Descrição Valores Leitura/Gravação Control Circuit 2: Cool ECO Offset 1~10 Leitura/Gravação Temperature Control Circuit 2: External MBS/KNX 0: Not Available Leitura/Gravação Thermostat Available 1: Available Control Zone 2: Thermostat Setting 0~65535 Leitura/Gravação Control Zone 2: Room Ambient -32667~32667 Leitura/Gravação Temperature...
Page 129 FUNCIONAMENTO Availability Offset Descrição Valores Leitura/Gravação 0: No Status Cool. OTC 1 1: Points Leitura 2: Fix Status Circuit 1: Water heating Fix 0~80 Leitura Setting Temp Status Circuit 1: Water cooling Fix 0~80 Leitura Setting Temp 0: ECO Estado Circuito 1: Modo ECO Leitura 1: Comfort Estado Circuito 1: temperatura de...
Page 130 FUNCIONAMENTO Availability Offset Descrição Valores Leitura/Gravação 0: Stop Estado de depósito de DHW Ligar/ Leitura Parar 1: Run Estado de temperatura de ajuste para 0~80 Leitura depósito de DHW 0: Disable Status DHW Boost Leitura 1: Enable Reservado 0: Standard Estado do modo de consumo de DHW Leitura 1: High demand...
Page 131 FUNCIONAMENTO Availability Offset Descrição Valores Leitura/Gravação b0: Zone 1 Heating Available b1: Zone 2 Heating Available b2: Zone 1 Cooling Available b3: Zone 2 Cooling Available b4: DHWT Available b5: SWP Available Configuração do sistema b6: Room thermostat Leitura available Zone 1 b7: Room thermostat available Zone 2 b8: Wireless Setting C1...
Page 132 FUNCIONAMENTO Availability Offset Descrição Valores Leitura/Gravação Software LCD Leitura Potência da unidade Leitura Unit Power Consumption Leitura 0~100 Apenas para Water Outler HP (TwoHP) Leitura YUTAKI S e S Combi Ta1av: Outdoor Unit Ambient Average -80~100 Leitura Temperature Ta2: Second Ambient Temperature -80~100 Leitura (inst)
Page 133 FUNCIONAMENTO Availability Offset Descrição Valores Leitura/Gravação 0: Alarm Número de alarme Leitura XXX: Alarm number Temperatura de descarga R134a Leitura Temperatura de aspiração R134a Leitura Pressão de descarga R134a Leitura Pressão de aspiração R134a Leitura Frequência do compressor R134a Leitura Abertura da válvula de expansão Leitura interior R134a...
Page 134 FUNCIONAMENTO 5.3 UNIDADES EXTERIORES Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Descrição Valores Leitura/Gravação Temperatura do ar exterior -63ºC ~ 63ºC Leitura Compressor Discharge Temperature...
Page 135 FUNCIONAMENTO 5.4 FUNÇÕES OPCIONAIS Some optional functions of the indoor units have been added so that they can be managed from the BMS. Offset Descrição Valores Leitura/Gravação b1 (Heating temperature compensation) Leitura/Gravação b2 (Circulation function at heating Thermo-OFF) Leitura/Gravação b4 (Change of filter cleaning period) Leitura/Gravação c5 (Static pressure selection) Leitura/Gravação...
Page 136: Jogo De Configuração Da Rede
Se o LED2 continuar a piscar, contacte o serviço de apoio ao cliente da Hitachi 6 JOGO DE CONFIGURAÇÃO DA REDE Este acessório proporciona todos os cabos necessários para os instaladores Hitachi quando realizam uma instalação de Modbus. Lista de componentes:...
Page 137: Produktvejledning
1.1 KLASSIFIKATIONER AF ENHEDER Kontrol af grænseflade til styreenhed Mellemrum H-LINK II kompatibel Maksimalt antal styrbare enheder (8/16/64) MB: Modbus gateway NET: Gateway til CSNET Manager 1.2 MODELLER BESKRIVELSE HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 LISTE MED TILBEHØRS BESKRIVELSE Netkonfigurationssæt PMML0351A rev.4 - 04/2020...
Page 138: Generelle Data Om Det Nye Produkt
Maks. 100 m i henhold til IEEE 802.3 H-LINK Element Specifikationer HC-A(16/64)MB: SET FREE, UTOPIA, CENTRIFUGAL og HEATING-systemer Kommunikation med HC-A8MB og HC-A64NET: INDSTIL GRATIS, UTOPIA og CENTRIFUGAL-systemer Kommunikationslinje Afskærmet parsnoet kabel, ikke polær Kommunikationssystem Halv dupleks Kommunikationsmetode Asynkron...
Page 139: Montering
MONTERING 3 MONTERING 3.1 OVERSIGT OVER SIKKERHED FA R E • Læs denne vejledning grundigt før udførelse af monteringsarbe- • Børn bør holdes under opsyn, så de ikke leger med apparatet. jdet. • Kontrollér, at de elektriske komponenter, der leveres på stedet, • Denne anordning må ikke monteres på steder, som er offentligt (hovedkontakter, kredsløbsafbrydere, ledninger, forbindelsesstik, og tilgængelige. Monter den i stedet inden i et el-skab, som kun kan ledningsklemmer) er valgt ud fra de angivne elektriske data, der er åbnes ved hjælp af et stykke værktøj, og som beskytter imod angivet i dette dokument, samt at de overholder nationale og lokale eventuelle elektromagnetiske forstyrrelser. regler. Om nødvendigt, skal du kontakte de lokale myndigheder ve- drørende standarder, regler, bestemmelser osv. • Tilslut ikke strømforsyning, før installationen af enheden er ud- ført korrekt. Afbryd altid strømforsyningen til enheden, inden al •...
Page 140 RS485   Modbus RTU til HC-A(8/16/64)MB Ikke disponibel til HC-A64NET H-LINK Kommunicationsbus med  Hitachi-enhder  LED-indikator for drift DIN-skinne 35 mm til samling inden i  elboksen 3.5 MONTERINGSAFSTAND Hold det grå område frit for at sikre, at enheden fungerer korrekt.
Page 141 MONTERING 3.6 FREMGANGSMÅDE FOR MONTERING FA R E • Montér ikke denne enhed på steder, hvor den er offentligt • Alle enheder, der ikke er tilsluttet eller ikke har strømtilførsel, når Net- tilgængeligt. Montér den i et aflukke eller andre steder, som kun work / Modbus slås til, vil ikke blive registreret og skal konfigureres kan tilgås ved hjælp af et stykke værktøj. senere. • Tilslut ikke strømforsyning, før installationen af enheden er ud- - Inden strømforsyningen tilsluttes og der tændes for Network / ført korrekt. Afbryd altid strømforsyningen til enheden, inden al Modbus gateways, skal du sikre dig, at:...
Page 142 MONTERING Konfiguration via Ethernet-port 1 Slut netværkskablet til en computer via et Ethernet-kabel (felt leveret eller tilgængelige med i netkonfigurationssættet eller med i CSNET MANAGER). 2 Indtast følgende parametre: • IP-adresse: 192.168.0.4 • Port: Modbus Gateway/ HC-A64NET 3 Tryk på -knappen på...
Page 143 MONTERING “Netværksinformation” Når netværksenheden er blevet integreret i LAN/Modbus-nettet via Ethernet, skal følgende parametre konfigureres: • IP-adresse: Tillad ændring af IP til enhedsport til netværket (“192.168.0.4” som standard). • Maske: Bed din IT-tekniker om en behørig værdi (“255.255.255.0” som standard). •...
Page 144: Elektrisk Ledningsføring
SW1-2: Ikke i brug (skal altid stå på “ON”) B E M Æ R K (*) Ikke til HC-A64NET. 5 DRIFT 5.1 KOMPATIBILITET Disse apparater er ikke kompatible med nogen af de følgende Hitachi styreenheder: - Centraliseret fjernbetjeninger - Aircondition styringer til bygninger (*) - Andre Hitachi BMS Gateways (LONWORKS, BACNET, KNX, FIDELIO) - Andre Hitachi MODBUS Gateways - Andre enheder af samme model B E M Æ...
Page 145 DRIFT 5.2 INDRE ENHEDER 5.2.1 Tilgængelige data for HC-A(8/16/64)MB Offset (1) Navn Beskrivelse Værdier Læs/Skriv 0: Eksisterer ikke EXIST Eksisterer Læs 1: Eksisterer SYSTEM_ADDRESS Systemadresse 0~63 Læs UNIT_ADDRESS Enhedsadresse 0: Stop On-/Off- SET_ONOFF Læs/Skriv indstillingens rækkefølge 1: On 0: Afkøling 1: Tørring Funktions- SET_MODE...
Page 146 DRIFT Offset (1) Navn Beskrivelse Værdier Læs/Skriv Årsag til STOP_CAUSE (Læs service-vejledningen) Læs kompressorstop Indendørsenhed (Ikke VALVE_OPEN 0~100 ekspansionsventilåbning anvendt) 0: OFF 1: Thermo OFF OPER_CONDITION Enhedens driftstilstand Læs 2: Thermo ON 3: Alarm (Ikke anvendt) (Ikke anvendt) (Ikke anvendt) (Ikke anvendt) AMBIENT Omgivelsestemperatur (2)
Page 147 DRIFT 5.2.2 Tilgængelige data for HC-A(16/64)MB Availability Offset Beskrivelse Værdier Læs/Skriv RAC- 0: No exist Eksisterer Læs 1: Exist Systemadresse H-LINK 1: 0~15 Læs Enhedsadresse H-LINK 2: 0~63 Type 0: Indoor Unit Læs 0: Stop On-/Off-indstillingens rækkefølge Læs/Skriv 1: Run 0: Cool 1: Dry Funktionsindstillingens rækkefølge...
Page 148 DRIFT Availability Offset Beskrivelse Værdier Læs/Skriv RAC- 0: Low 1: Medium Ventilator status 2: High Læs 3: High2 4: Auto ºC (set according to the Setting temperature status Læs unit working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as Læs intervals status 195)
Page 149 DRIFT Availability Offset Beskrivelse Værdier Læs/Skriv RAC- 0: Stop Run/stop-kontrolenhed Læs/Skriv 1: Run 0: Cool Styreenheds driftsmåde Læs/Skriv 1: Heat 0: Stop Styrekreds 1 Run/stop Læs/Skriv 1: Run 0: No 1: Points Control Heat. OTC Zone 1 Læs/Skriv 2: Gradient 3: Fix 0: No Control Cool.
Page 150 DRIFT Availability Offset Beskrivelse Værdier Læs/Skriv RAC- Control Circuit 2: Cool ECO Offset 1~10 Læs/Skriv Temperature Control Circuit 2: External MBS/KNX 0: Not Available Læs/Skriv Thermostat Available 1: Available Control Zone 2: Thermostat Setting 0~65535 Læs/Skriv Control Zone 2: Room Ambient -32667~32667 Læs/Skriv Temperature...
Page 151 DRIFT Availability Offset Beskrivelse Værdier Læs/Skriv RAC- 0: No Status Cool. OTC 1 1: Points Læs 2: Fix Status Circuit 1: Water heating Fix 0~80 Læs Setting Temp Status Circuit 1: Water cooling Fix 0~80 Læs Setting Temp 0: ECO Status kredsløb 1: ECO driftsmåde Læs 1: Comfort...
Page 152 DRIFT Availability Offset Beskrivelse Værdier Læs/Skriv RAC- 0: Stop Status DHW-beholders run/stop Læs 1: Run Status DHW-beholders 0~80 Læs indstillingstemperatur 0: Disable Status DHW Boost Læs 1: Enable Reserveret 0: Standard Status driftsmåden DHW efterspørgsel Læs 1: High demand Status DHW Temperature -80~100 Læs 0: Stop...
Page 153 DRIFT Availability Offset Beskrivelse Værdier Læs/Skriv RAC- b0: Zone 1 Heating Available b1: Zone 2 Heating Available b2: Zone 1 Cooling Available b3: Zone 2 Cooling Available b4: DHWT Available b5: SWP Available System konfiguration b6: Room thermostat Læs available Zone 1 b7: Room thermostat available Zone 2 b8: Wireless Setting C1...
Page 154 DRIFT Availability Offset Beskrivelse Værdier Læs/Skriv RAC- Software LCD Læs Enhedens kapacitet Læs Unit Power Consumption Læs 0~100 kun YUTAKI S & Water Outler HP (TwoHP) Læs S Combi Ta1av: Outdoor Unit Ambient Average -80~100 Læs Temperature Ta2: Second Ambient Temperature -80~100 Læs (inst)
Page 155 DRIFT Availability Offset Beskrivelse Værdier Læs/Skriv RAC- 0: Alarm Alarmnummer Læs XXX: Alarm number Udladningstemperatur R134a Læs Sugetemperatur R134a Læs R134a udladningstryk Læs R134a sugetryk Læs Kompressorfrekvens R134a Læs Indendørs ekspansionsventilåbning Læs R134a Kompressor nuværende værdi R134a Læs Genforsøgskode R134a Læs R134 Te SH Læs...
Page 156 DRIFT 5.3 UDENDØRSENHEDER Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Beskrivelse Værdier Læs/Skriv Outdoor Air Temperature -63ºC ~ 63ºC Læs Compressor Discharge Temperature...
Page 157 5.6 FEJLFINDING ALARMKODE BESKRIVELSE MODFORANSTALTNINGER Afbryd strømforsyningen til enheden og gentilslut den efter 5 sek. Hvis LED2 stadig blinker LED2 blinker Unormal drift bedes du kontakte Hitachi kundeservice. PMML0351A rev.4 - 04/2020...
Page 158: Netkonfigurationssæt
NETKONFIGURATIONSSÆT 6 NETKONFIGURATIONSSÆT Dette tilbehør indeholder alle de nødvendige kabler til Hitachi installatører under idriftsættelse af en Modbus installation. Liste over komponenter: USB-kabel Krydset ethernetkabel USB-stik USB-hukommelsesstikket indeholder et softwareværktøj til kontrol af Modbus kommunikation under idriftsættelse. USB-kablet skal kun bruges mens apparatet konfigureres (netværksparametre) Ethernet-kablet er til hurtig forbindelse med en bærbar computer ved kontrol af Modbus kommunikation.
Page 159: Productgids
1 PRODUCTGIDS 1.1 CLASSIFICATIE VAN DE UNIT Regeling interfacecontroller Scheidingsteken H-LINK II-compatibel Max. aantal regelbare units (8/16/64) MB: Modus-gateway NET: Gateway voor CSNET Manager 1.2 MODELLEN BESCHRIJVING HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 LIJST VAN ACCESSOIRE BESCHRIJVING Netconfiguratiekit PMML0351A rev.4 - 04/2020...
Page 160: Algemene Gegevens Nieuw Product
Lengte Max. 100 m conform IEEE 802.3 H-LINK Item Specificaties HC-A(16/64)MB: SET FREE-, UTOPIA-, CENTRIFUGAL- en HEATING-systemen Communicatie met HC-A8MB en HC-A64NET: SET FREE-, UTOPIA- en CENTRIFUGAL-systemen Communicatieleiding Afgeschermde gevlochten kabel, geen polariteit Communicatiesysteem Half-duplex Communicatiemethode Asynchroon Transmissiesnelheid 9600 Bauds Kabellengte Max.
Page 161: Installatie
INSTALLATIE 3 INSTALLATIE 3.1 VEILIGHEIDSSAMENVATTING G E VA A R • Lees deze handleiding zorgvuldig door voordat u aan de instal- • Kinderen moeten onder toezicht staan om te voorkomen dat ze spelen latiewerken begint. met het apparaat. • Installeer dit apparaat niet op plaatsen die openbaar toegankelijk • Controleer of de niet-meegeleverde elektrische onderdelen (hoofd- zijn. Installeer het in aansluitkasten die alleen met behulp van een schakelaars, zekeringautomaten, draden, aansluitingen en klemmen) werktuig kunnen worden geopend en bescherming bieden tegen voldoen aan de elektrische specificaties beschreven in dit hoofdstuk mogelijk elektromagnetische interferenties. en voldoen aan de nationale en locale regulatie. Neem indien nodig contact op met de plaatselijke autoriteiten voor informatie over nor- •...
Page 162  RS485  Modus RTU voor HC-A(8/16/64)MB Niet beschikbaar voor HC-A64NET H-LINK-communicatiebus  met Hitachi-units  Aan/uit-indicator Rail DIN 35 mm voor montage in de  elektrische box 3.5 INSTALLATIERUIMTE Houd de grijze ruimte vrij, voor een correcte werking van het apparaat.
Page 163 INSTALLATIE 3.6 INSTALLATIEPROCEDURE G E VA A R • Installeer de unit niet op een openbaar toegankelijke plek. Instal- • Elke unit die niet is aangesloten of die geen stroom krijgt wanneer u leer hem in een afgesloten ruimte of op een plek die alleen toe- de netwerk-/Modbus-gateways inschakelt, wordt niet herkend en moet gankelijk is met behulp van een werktuig. later alsnog worden geconfigureerd. • Sluit de spanning niet aan voordat de installatie is voltooid. - Voordat u de voeding inschakelt op de network-/Modbus- Schakel altijd eerste de voeding uit voordat u onderhouds- of gateways, dient u te controleren of: reparatiewerken uitvoert.
Page 164 INSTALLATIE Configuratie via Ethernet-poort 1 Sluit het netwerkapparaat aan op een computer met behulp van een Ethernet-kabel (niet meegeleverd, maar beschikbaar in het netconfiguratiekit of in het CSNET MANAGER) 2 Voer de volgende parameters in: • IP-adres: 192.168.0.4 • Poort: Modbus Gateway/ HC-A64NET 3 Druk op de -knop in het scherm.
Page 165 INSTALLATIE “Netwerkgegevens” Wanneer het netwerkapparaat op het LAN/Modbus-netwerk is aangesloten via Ethernet, configureer dan de volgende parameters: • IP-adres: Hiermee kunt u het IP-adres van het netwerkapparaat aanpassen (standaardinstelling “192.168.0.4”). • Mask: vraag uw IT-technicus om de correcte waarde (standaardinstelling “255.255.255.0”). •...
Page 166: Elektrische Bedrading
SW1-2: Niet gebruikt (altijd op “ON”) O P M E R K I N G (*) Niet van toepassing op HC-A64NET. 5 BEDRIJF 5.1 COMPATIBILITEIT Deze apparaten zijn niet compatibel met de volgende Hitachi-controllers: - Gecentraliseerd externe bediening - Klimaatbediening voor gebouwen (*) - Andere Hitachi BMS-gateways (LONWORKS, BACNET, KNX, FIDELIO) - Andere Hitachi MODBUS-gateways - Andere eenheden van hetzelfde model O P M E R K I N G (*) HC-A64NET is compatibel met CSNET Manager.
Page 167 BEDRIJF 5.2 BINNENUNITS 5.2.1 Beschikbare gegevens voor HC-A(8/16/64)MB Offset (1) Name Beschrijving Waarden Lezen/Schrijven 0: Bestaat niet EXIST Bestaat Lezen 1: Bestaat SYSTEM_ADDRESS Systeemadres 0~63 Lezen UNIT_ Unitadres ADDRESS 0: Stoppen Aan/uit- SET_ONOFF Lezen/Schrijven instellingsvolgorde 1: Aan 0: Koelen 1: Ontvochtigen Volgorde SET_MODE 2: Ventilator...
Page 168 BEDRIJF Offset (1) Name Beschrijving Waarden Lezen/Schrijven Oorzaak van stoppen (Raadpleeg STOP_CAUSE Lezen compressor onderhoudshandleiding van unit) Opening VALVE_OPEN 0~100 (Niet gebruikt) expansieklep binnenunit 0: OFF 1: Thermo OFF OPER_CONDITION Bedrijfscondities Lezen 2: Thermo ON 3: Alarm (Niet gebruikt) (Niet gebruikt) (Niet gebruikt) (Niet gebruikt) AMBIENT...
Page 169 BEDRIJF 5.2.2 Beschikbare gegevens voor HC-A(16/64)MB Availability Offset Beschrijving Waarden Lezen/Schrijven 0: No exist Bestaat Lezen 1: Exist Systeemadres H-LINK 1: 0~15 Lezen Unitadres H-LINK 2: 0~63 Type 0: Indoor Unit Lezen 0: Stop Aan/uit-instellingsvolgorde Lezen/Schrijven 1: Run 0: Cool 1: Dry Volgorde modusinstelling 2: Fan...
Page 170 BEDRIJF Availability Offset Beschrijving Waarden Lezen/Schrijven 0: Low 1: Medium Status ventilator 2: High Lezen 3: High2 4: Auto ºC (set according to the Status ingestelde temperatuur Lezen unit working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as Lezen intervals status 195)
Page 171 BEDRIJF Availability Offset Beschrijving Waarden Lezen/Schrijven 38~49 Voorbehouden 0: Stop Regeling starten/stoppen van unit Lezen/Schrijven 1: Run 0: Cool Regeling besturingsmodus Lezen/Schrijven 1: Verwarming 0: Stop Regeling starten/stoppen circuit 1 Lezen/Schrijven 1: Run 0: No 1: Points Control Heat. OTC Zone 1 Lezen/Schrijven 2: Gradient 3: Fix...
Page 172 BEDRIJF Availability Offset Beschrijving Waarden Lezen/Schrijven Control Circuit 2: Cool ECO Offset 1~10 Lezen/Schrijven Temperature Control Circuit 2: External MBS/KNX 0: Not Available Lezen/Schrijven Thermostat Available 1: Available Control Zone 2: Thermostat Setting 0~65535 Lezen/Schrijven Control Zone 2: Room Ambient -32667~32667 Lezen/Schrijven Temperature...
Page 173 BEDRIJF Availability Offset Beschrijving Waarden Lezen/Schrijven 0: No Status Cool. OTC 1 1: Points Lezen 2: Fix Status Circuit 1: Water heating Fix 0~80 Lezen Setting Temp Status Circuit 1: Water cooling Fix 0~80 Lezen Setting Temp 0: ECO Status circuit 1: ECO-modus Lezen 1: Comfort Status circuit 1: Verwarming ECO...
Page 174 BEDRIJF Availability Offset Beschrijving Waarden Lezen/Schrijven 0: Stop Status starten/stoppen van Lezen warmwaterketel 1: Run Status ingestelde temperatuur 0~80 Lezen warmwaterketel 0: Disable Status DHW Boost Lezen 1: Enable Voorbehouden 0: Standard Status vraagmodus warm tapwater Lezen 1: High demand Status DHW Temperature -80~100 Lezen...
Page 175 BEDRIJF Availability Offset Beschrijving Waarden Lezen/Schrijven b0: Zone 1 Heating Available b1: Zone 2 Heating Available b2: Zone 1 Cooling Available b3: Zone 2 Cooling Available b4: DHWT Available b5: SWP Available Systeemconfiguratie b6: Room thermostat Lezen available Zone 1 b7: Room thermostat available Zone 2 b8: Wireless Setting C1...
Page 176 BEDRIJF Availability Offset Beschrijving Waarden Lezen/Schrijven Software LCD Lezen Capaciteit van unit Lezen Unit Power Consumption Lezen 0~100 Alleen voor Water Outler HP (TwoHP) Lezen YUTAKI S & S-Combi Ta1av: Outdoor Unit Ambient Average -80~100 Lezen Temperature Ta2: Second Ambient Temperature -80~100 Lezen (inst)
Page 177 BEDRIJF Availability Offset Beschrijving Waarden Lezen/Schrijven 0: Alarm Alarmnummer Lezen XXX: Alarm number Uitlaattemperatuur R134a Lezen Aanzuigtemperatuur R134a Lezen Uitlaatdruk R134a Lezen Aanzuigdruk R134a Lezen Compressorfrequentie R134a Lezen Opening expansieventiel binnenunit Lezen R134a Spanningswaarde compressor R134a Lezen Code opnieuw proberen R134a Lezen R134 Te SH Lezen...
Page 178 BEDRIJF 5.3 BUITENUNITS Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Beschrijving Waarden Lezen/Schrijven Outdoor Air Temperature -63ºC ~ 63ºC Lezen Compressor Discharge Temperature...
Page 179 ALARMCODE BESCHRIJVING OPLOSSING Schakel de netvoeding naar het apparaat uit en schakelt hem na 5 seconden opnieuw in. LED2 knippert Abnormale werking Als LED2 nog altijd knippert, neem dan contact op met de klantenservice van Hitachi. PMML0351A rev.4 - 04/2020...
Page 180: Netconfiguratiekit
NETCONFIGURATIEKIT 6 NETCONFIGURATIEKIT Dit accessoire biedt Hitachi-installateurs alle nodige kabels voor het inbedrijfstellen van een Modbus-installatie. Lijst van onderdelen: USB-kabel Gekruiste Ethernet-kabel USB-geheugenstick De USB-geheugenstick bevat een software voor het controleren van de communicatie tijdens de inbedrijfstelling. De USB-kabel is alleen nodig voor het configureren van het apparaat (netwerkparameters).
Page 181: Produktguide
1 PRODUKTGUIDE 1.1 KLASSIFICERING AV ENHETER Kontrollenhet för gränssnitt Bindestreck H-LINK II-kompatibel Max antal styrbara enheter (8/16/64) MB: Modbus-gateway NET: Gateway för CSNET Manager 1.2 MODELLER BESKRIVNING HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 TILLBEHÖRSLISTA BESKRIVNING Kit för nätkonfigurering PMML0351A rev.4 - 04/2020...
Page 182: Allmän Data För Ny Produkt
Längd Max. 100 m enligt IEEE 802.3 H-LINK Objekt Specifikationer HC-A(16/64)MB: SET FREE, UTOPIA, CENTRIFUGAL and HEATING systems Kommunikation med HC-A8MB och HC-A64NET: SET FREE, UTOPIA och CENTRIFUGAL-system Kommunikationslinje Tvinnad skärmad parkabel, ingen polaritet. Kommunikationssystem Halv-duplex Kommunikationsmetod Asynkron Överföringshastighet 9 600 båd...
Page 183: Installation
INSTALLATION 3 INSTALLATION 3.1 SÄKERHETSSAMMANFATTNING FA R A • Läs denna handbok noggrant innan du påbörjar installationen. • Håll uppsikt över barn och låt dem inte leka med installationen. • Installera inte enheten på en platser där den är tillgänglig för • Se till att alla ej-medföljande elektriska komponenter (huvudströmbry- allmänheten. Installera den i en elektrisk inhängnad där den en- tare, kretsbrytare, kablar, kontakter och kabelanslutningar) har valts dast kan kommas åt med verktyg och som ger skydd mot even- enligt de elektriska uppgifter som angetts i det här dokumentet och tuella elektromagnetiska störningar.
Page 184 RS485   Modbus RTU för HC-A(8/16/64)MB Inte tillgänglig för HC-A64NET H-LINK, kommunikationsbus med  Hitachi-enheter  Lysdiodindikator för drift Rail DIN 35 mm för montering innanför  kopplingslådan 3.5 INSTALLATIONSPLATS Lämna det gråa området fritt för korrekt användning av enheten.
Page 185 INSTALLATION 3.6 INSTALLATIONSPROCEDUR FA R A • Installera inte enheten på platser där allmänheten kan komma åt • Enheter som inte är anslutna till eller inte har någon strömtillförsel när den. Installera den i ett slutet område eller dylikt där den endast Nätverk-/Modbus-gateways slås på, identifieras inte och måste kon- kan kommas åt med ett verktyg. figureras senare. • Anslut inte strömförsörjningen förrän installationen av enheten - Innan du strömsätter och startar Nätverks -/ Modbus-gateways, är korrekt utförd. Koppla alltid från enhetens spänningsmatnin- måste du se till att: gen innan något underhåll eller servicearbete utförs.
Page 186 INSTALLATION Konfigurering via Ethernet-port 1 Anslut nätverkenheten till en dator via en Ethernet-kabel (medföljer inte, men tillgänglig via kitet för nätkonfigurering eller CSNET MANAGER) 2 Mata in följande parametrar: • IP-adress: 192.168.0.4 • Port: Modbus Gateway/ HC-A64NET 3 Tryck på -knappen på...
Page 187 INSTALLATION “Nätverkskonfiguration”-tabell När nätverksenheten är integrerad i LAN/Modbusnätet via Ethernet, ska du konfigurera följande parametrar: • IP-adress: Tillåter dig ändra IP-adressen på nätverksenhetens port (“192.168.0.4” som standard). • Mask: Använd 255.255.255.0 som standard eller be din IT-tekniker om korrekt värde (“255.255.255.0” som standard). •...
Page 188: Elektriska Ledningar
(lämna alltid på "ON") O B S ! (*) Gäller inte för HC-A64NET. 5 DRIFT 5.1 KOMPATIBILITET Dessa enheter är inte kompatibla med någon av HITACHIs följande styrenheter: - Centrala fjärrkontroller - Luftkonditioneringskontroller för byggnader (*) - Andra Hitachi BMS Gateways (LONWORKS, BACNET, KNX, FIDELIO) - Andra Hitachi MODBUS Gateways - Andra enheter av samma modell O B S ! (*) HC-A64NET är kompatibelt med CSNET Manager. PMML0351A rev.4 - 04/2020...
Page 189 DRIFT 5.2 INNEHÅLL 5.2.1 Tillgängliga datauppgifter för HC-A(8/16/64)MB Offset (1) Benämning Beskrivning Värden Läs/skriv 0: Finns ej EXIST Finns Läs 1: Finns SYSTEM_ADDRESS Systemadress 0~63 Läs UNIT_ Enhetsadress ADDRESS 0: Stopp SET_ONOFF På/av-inställningsordning Läs/skriv 1: Kör 0: Svalt 1: Torrt SET_MODE Kommandon för inställningsläge 2: Fläkt...
Page 190 DRIFT Offset (1) Benämning Beskrivning Värden Läs/skriv Inomhus- enhetens VALVE_OPEN 0~100 (Används ej) öppning av expansionsventil 0: OFF 1: Thermo OFF OPER_CONDITION Enhetens driftsvillkor Läs 2: Thermo ON 3: Larm (Används ej) (Används ej) (Används ej) (Används ej) AMBIENT TEMPERATURE Omgivningstemperatur (2) -63ºC ~ 63ºC Läs...
Page 191 DRIFT 5.2.2 Tillgängliga data HC-A(16/64)MB Availability Offset Beskrivning Värden Läs/skriv 0: No exist Finns Läs 1: Exist Systemadress H-LINK 1: 0~15 Läs Enhetsadress H-LINK 2: 0~63 0: Indoor Unit Läs 0: Stop På/av-inställningsordning Läs/skriv 1: Run 0: Cool 1: Dry Kommandon för inställningsläge 2: Fan Läs/skriv...
Page 192 DRIFT Availability Offset Beskrivning Värden Läs/skriv 0: Low 1: Medium Fäktstatus 2: High Läs 3: High2 4: Auto ºC (set according to the Status för temperaturinställning Läs unit working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as Läs intervals status 195) Heating temperature setting for AUTO...
Page 193 DRIFT Availability Offset Beskrivning Värden Läs/skriv 38~49 Reserverad 0: Stop Styrenhet start/stopp Läs/skriv 1: Run 0: Cool Styrenhet läge Läs/skriv 1: Heat 0: Stop Kontrollkrets 1 start/stopp Läs/skriv 1: Run 0: No 1: Points Control Heat. OTC Zone 1 Läs/skriv 2: Gradient 3: Fix 0: No...
Page 194 DRIFT Availability Offset Beskrivning Värden Läs/skriv Control Circuit 2: Cool ECO Offset 1~10 Läs/skriv Temperature Control Circuit 2: External MBS/KNX 0: Not Available Läs/skriv Thermostat Available 1: Available Control Zone 2: Thermostat Setting 0~65535 Läs/skriv Control Zone 2: Room Ambient -32667~32667 Läs/skriv Temperature...
Page 195 DRIFT Availability Offset Beskrivning Värden Läs/skriv Status Circuit 1: Water heating Fix 0~80 Läs Setting Temp Status Circuit 1: Water cooling Fix 0~80 Läs Setting Temp 0: ECO Status Circuit 1: Eco mode Läs 1: Comfort Status Circuit 1: Heat ECO Offset 1~10 Läs Temperature...
Page 196 DRIFT Availability Offset Beskrivning Värden Läs/skriv 0: Disable Status DHW Boost Läs 1: Enable Reserverad 0: Standard Status DHW-behovsläge Läs 1: High demand Status DHW Temperature -80~100 Läs 0: Stop Status pool kör/stopp Läs 1: Run Status Swim. Pool Setting 0~80 Läs Temperature...
Page 197 DRIFT Availability Offset Beskrivning Värden Läs/skriv 0: OFF 1: Cool Demand –OFF 2: Cool Thermo-OFF 3: Cool Thermo-ON 4: Heat Demand-OFF 5: Heat Thermo-OFF Driftstatus Läs 6: Heat Thermo-ON 7: DHW-OFF 8: DHW-ON 9: SWP-OFF 10: SWP-ON 11: Alarm Outdoor Ambient Tº -80~100 Läs (Outdoor ambient temperature)
Page 198 DRIFT Availability Offset Beskrivning Värden Läs/skriv 0: Yutaki S 1: Yutaki SC 2: Yutaki S80 Enhetsmodell. 3: Yutaki M Läs 4: Yutaki SC Lite (New) 5: Yutampo (New) 6: YCC (New) Th: Water Temp Setting (Ttwo) -80~100 Läs Vattenflöde Water Flow [0.1m3/h] Läs Pump Speed 0~100...
Page 199 DRIFT Availability Offset Beskrivning Värden Läs/skriv YCC - Required Units Läs N O T E • Register address is calculated as: 5000+(Modbus_Id*200)+offset • Modbus_Id as configured by configuration software • For VRF / Package units, only the relevant data are available (heating units registers will not give any value). The situation is the same for heating units (registers related to air/air units will not give any value). • Availability: PAC: VRF and package units. RAC: Domestic units connected to the H-link via PSC-6RAD or SPX-RAMHLK ATW: Air to water units.
Page 200 DRIFT 5.3 UTOMHUSENHETER Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Beskrivning Värden Läs/skriv Outdoor Air Temperature -63ºC ~ 63ºC Läs Compressor Discharge Temperature...
Page 201 DRIFT 5.4 VALFRIA FUNKTIONER Some optional functions of the indoor units have been added so that they can be managed from the BMS. Offset Beskrivning Värden Läs/skriv b1 (Heating temperature compensation) Läs/skriv b2 (Circulation function at heating Thermo-OFF) Läs/skriv b4 (Change of filter cleaning period) Läs/skriv c5 (Static pressure selection) Läs/skriv...
Page 202: Kit För Nätkonfigurering
Slå av enhetens ström och återanslut den igen efter 5 sekunder. Om LED2 fortfarande blinkar LED2 blinkar Onormal drift bör du kontakta HITACHIs kundservice. 6 KIT FÖR NÄTKONFIGURERING Detta tillbehör tillhandahåller alla de kablar som Hitachi-installatörer behöver för driftsättning av en Modbus-installation. Komponentlista: USB -kabel Korsad Ethernet-kabel USB-minne I USB-minnet ingår ett mjukvaruverktyg som bör kontrolleras vid driftsättning av Modbus-kommunikation.
Page 203: Οδηγοσ Προϊοντοσ
Έλεγχος ελεγκτή διασύνδεσης Διαχωρισμός με παύλα Συμβατότητα με H-LINK II Μέγιστος αριθμός μονάδων που ελέγχονται (8/16/64) MB: Modbus gateway NET: Gateway για CSNET Manager 1.2 ΜΟΝΤΈΛΑ ΠΈΡΙΓΡΑΦΗ HC-A8MB HC-A16MB HC-A64MB HC-A64NET 1.3 ΛΙΣΤΑ ΑΞΈΣΟΥΑΡ ΠΈΡΙΓΡΑΦΗ Κιτ διαμόρφωσης δικτύου PMML0351A rev.4 - 04/2020...
Page 204: Γενικα Δεδομενα Νεου Προϊοντοσ
Μεγ. 100 m κατά IEEE 802.3 H-LINK Στοιχείο Προδιαγραφές HC-A(16/64)MB: SET FREE, UTOPIA, CENTRIFUGAL ΚΑΙ ΘΕΡΜΑΝΣΗ συστήματα Επικοινωνία με HC-A8MB και HC-A64NET: SET FREE, UTOPIA και CENTRIFUGAL συστήματα Γραμμή επικοινωνίας Θωρακισμένο καλώδιο συνεστραμμένου ζεύγους, χωρίς πολικότητα Σύστημα επικοινωνίας Ημι-αμφίδρομη Μέθοδος επικοινωνίας Ασύγχρονη...
Page 205: Εγκατασταση
ΕΓΚΑΤΆΣΤΑΣΗ 3 ΈΓΚΑΤΑΣΤΑΣΗ 3.1 ΣΥΝΟΨΗ ΑΣΦΑΛΈΙΑΣ Κ Ι Ν ΔΥ Ν Ο Σ • Διαβάστε αυτό το εγχειρίδιο προσεκτικά, προτού εκτελέσετε την • Τα παιδιά θα πρέπει να επιτηρούνται και να μην παίζουν με τη συσκευή. εγκατάσταση. • Βεβαιωθείτε ότι τα μη παρεχόμενα ηλεκτρικά εξαρτήματα (κύριοι • Μην εγκαθιστάτε αυτήν τη συσκευή σε χώρους όπου έχει διακόπτες τροφοδοσίας, διακόπτες κυκλώματος, καλώδια, συνδέσεις πρόσβαση το ευρύ κοινό. Εγκαταστήστε την σε ηλεκτρικά...
Page 206  RS485  Modbus RTU για HC-A(8/16/64)MB Μη διαθέσιμο για HC-A64NET H-LINK - Δίαυλος επικοινωνίας με  μονάδες Hitachi  Λυχνία ένδειξης λειτουργίας Οδηγός DIN 35 mm για συναρμολόγηση  μέσα στο ηλεκτρικό κουτί 3.5 ΧΩΡΟΣ ΈΓΚΑΤΑΣΤΑΣΗΣ Διατηρήστε καθαρή την γκρι περιοχή για τη σωστή λειτουργία της συσκευής.
Page 207 ΕΓΚΑΤΆΣΤΑΣΗ 3.6 ΔΙΑΔΙΚΑΣΙΑ ΈΓΚΑΤΑΣΤΑΣΗΣ Κ Ι Ν ΔΥ Ν Ο Σ • Μην εγκαθιστάτε αυτή τη συσκευή σε χώρους στους οποίους έχει • Εάν κάποια μονάδα δεν είναι συνδεδεμένη ή δεν έχει τροφοδοσία πρόσβαση το ευρύ κοινό. Εγκαταστήστε την με περιφράγματα ή ρεύματος όταν ενεργοποιήσετε το Network / Modbus gateways, η σε χώρους στους οποίους η πρόσβαση γίνεται μόνο με τη χρήση μονάδα δεν θα αναγνωριστεί και θα πρέπει να ρυθμιστεί αργότερα. ενός εργαλείου. - Πριν από την τροφοδοσία ρεύματος και την ενεργοποίηση των • Μην συνδέετε την τροφοδοσία ρεύματος προτού ολοκληρωθεί...
Page 208 ΕΓΚΑΤΆΣΤΑΣΗ Διαμόρφωση μέσω θύρας Ethernet 1 Συνδέστε τη συσκευή δικτύου σε ένα υπολογιστή με ένα καλώδιο ethernet (τομέα που παρέχονται ή διατίθενται με το κιτ διαμόρφωση δικτύου ή το CSNET MANAGER) 2 Είσοδος των παρακάτω παραμέτρων: • Διεύθυνση IP: 192.168.0.4 •...
Page 209 ΕΓΚΑΤΆΣΤΑΣΗ “Πληροφορίες δικτύου” Όταν η συσκευή δικτύου ενσωματώνεται στο δίκτυο LAN / Modbus μέσω Ethernet, ρυθμίστε τις παρακάτω παραμέτρους: • Διεύθυνση IP: Επιτρέψτε την τροποποίηση του IP της θύρας για τη συσκευή δικτύου (“192.168.0.4” από προεπιλογή). • Mask: Ρωτήστε τον τεχνικό υπολογιστών για τη κατάλληλη τιμή (“255.255.255.0” από προεπιλογή). •...
Page 210: Ηλεκτρικη Καλωδιωση
χρησιμοποιείται (πάντα να διατηρείται “ON”) Σ Η Μ Έ Ι Ω Σ Η (*) Δεν ισχύει για το HC-A64NET. 5 ΛΈΙΤΟΥΡΓΙΑ 5.1 ΣΥΜΒΑΤΟΤΗΤΑ Αυτές οι συσκευές δεν είναι συμβατές με κανέναν από τους παρακάτω ελεγκτές Hitachi: - Κεντρικό χειριστήρια - Χειριστήρια κλιματισμού για κτίρια (*) - Άλλα Hitachi BMS Gateways (LONWORKS, BACNET, KNX, FIDELIO) - Άλλα Hitachi MODBUS Gateways - Άλλες μονάδες του ίδιου μοντέλου...
Page 211 ΛΕΙΤΟΥΡΓΊΑ 5.2 ΈΣΩΤΈΡΙΚΈΣ ΜΟΝΑΔΈΣ 5.2.1 Διαθέσιμα δεδομένα HC-A (8/16/64)MB Offset (1) Όνομα Περιγραφή Τιμές Ανάγνωση/Έγγραφή 0: Δεν υπάρχει EXIST Υπάρχει Ανάγνωση 1: Υπάρχει SYSTEM_ADDRESS Διεύθυνση συστήματος 0~63 Ανάγνωση UNIT_ Διεύθυνση μονάδας ADDRESS 0: Διακοπή SET_ONOFF Εντολή ρύθμισης On/Off Ανάγνωση/Εγγραφή 1: Λειτουργία 0: Ψύξη...
Page 212 ΛΕΙΤΟΥΡΓΊΑ Offset (1) Όνομα Περιγραφή Τιμές Ανάγνωση/Έγγραφή (Διαβάστε το εγχειρίδιο STOP_CAUSE Αιτία διακοπής συμπιεστή Ανάγνωση συντήρησης της μονάδας) Άνοιγμα βαλβίδας εκτόνωσης VALVE_OPEN 0~100 Δεν χρησιμ. εσωτερικής μονάδας 0: OFF 1: Thermo OFF OPER_CONDITION Κατάσταση λειτουργίας μονάδας Ανάγνωση 2: Thermo ON 3: Προειδοποίηση...
Page 213 ΛΕΙΤΟΥΡΓΊΑ 5.2.2 Διαθεσιμα δεδομενα για HC-A(16/64)MB Availability Offset Περιγραφή Τιμές Read/Write 0: No exist Exist Read 1: Exist System address H-LINK 1: 0~15 Read Unit address H-LINK 2: 0~63 Τύπος 0: Indoor Unit Read 0: Stop On/Off setting order Read/Write 1: Run 0: Cool 1: Dry...
Page 214 ΛΕΙΤΟΥΡΓΊΑ Availability Offset Περιγραφή Τιμές Read/Write 0: Low 1: Medium Fan status 2: High Read 3: High2 4: Auto ºC (set according to the Setting temperature status Read unit working range) Temperature setting with 0.5°C ºC x10 (19.5ºC read as Read intervals status 195)
Page 215 ΛΕΙΤΟΥΡΓΊΑ Availability Offset Περιγραφή Τιμές Read/Write 0: Stop Control Unit Run/Stop Read/Write 1: Run 0: Cool Control Unit Mode Read/Write 1: Heat 0: Stop Control Circuit 1 Run/Stop Read/Write 1: Run 0: No 1: Points Control Heat. OTC Zone 1 Read/Write 2: Gradient 3: Fix...
Page 216 ΛΕΙΤΟΥΡΓΊΑ Availability Offset Περιγραφή Τιμές Read/Write Control Circuit 2: Cool ECO Offset 1~10 Read/Write Temperature Control Circuit 2: External MBS/KNX 0: Not Available Read/Write Thermostat Available 1: Available Control Zone 2: Thermostat Setting 0~65535 Read/Write Control Zone 2: Room Ambient -32667~32667 Read/Write Temperature...
Page 217 ΛΕΙΤΟΥΡΓΊΑ Availability Offset Περιγραφή Τιμές Read/Write Status Circuit 1: Water heating Fix 0~80 Read Setting Temp Status Circuit 1: Water cooling Fix 0~80 Read Setting Temp 0: ECO Status Circuit 1: Eco mode Read 1: Comfort Κατάσταση κύκλωμα 1: Θερμοκρασία 1~10 Read μετατόπισης...
Page 218 ΛΕΙΤΟΥΡΓΊΑ Availability Offset Περιγραφή Τιμές Read/Write 0: Disable Status DHW Boost Read 1: Enable Reserved 0: Standard Κατάσταση ζήτησης κατάσταση DHW Read 1: High demand Status DHW Temperature -80~100 Read 0: Stop Status Swim.Pool Run/Stop Read 1: Run Status Swim. Pool Setting 0~80 Read Temperature...
Page 219 ΛΕΙΤΟΥΡΓΊΑ Availability Offset Περιγραφή Τιμές Read/Write 0: OFF 1: Cool Demand –OFF 2: Cool Thermo-OFF 3: Cool Thermo-ON 4: Heat Demand-OFF 5: Heat Thermo-OFF Operation State Read 6: Heat Thermo-ON 7: DHW-OFF 8: DHW-ON 9: SWP-OFF 10: SWP-ON 11: Alarm Outdoor Ambient Tº...
Page 220 ΛΕΙΤΟΥΡΓΊΑ Availability Offset Περιγραφή Τιμές Read/Write 0: Yutaki S 1: Yutaki SC 2: Yutaki S80 Unit Model 3: Yutaki M Read 4: Yutaki SC Lite (New) 5: Yutampo (New) 6: YCC (New) Th: Water Temp Setting (Ttwo) -80~100 Read Water Flow Water Flow [0.1m3/h] Read Pump Speed...
Page 221 ΛΕΙΤΟΥΡΓΊΑ Availability Offset Περιγραφή Τιμές Read/Write YCC - Required Units Read N O T E • Register address is calculated as: 5000+(Modbus_Id*200)+offset • Modbus_Id as configured by configuration software • For VRF / Package units, only the relevant data are available (heating units registers will not give any value). The situation is the same for heating units (registers related to air/air units will not give any value). • Availability: PAC: VRF and package units. RAC: Domestic units connected to the H-link via PSC-6RAD or SPX-RAMHLK ATW: Air to water units.
Page 222 ΛΕΙΤΟΥΡΓΊΑ 5.3 ΈΞΩΤΈΡΙΚΈΣ ΜΟΝΑΔΈΣ Some state registers about outdoor unit have been added. Using these registers it is now possible to know the status of the refrigerant cycle. Some control registers have also been added. Offset Περιγραφή Τιμές Read/Write Outdoor Air Temperature -63ºC ~ 63ºC Read Compressor Discharge Temperature...
Page 223 ΛΕΙΤΟΥΡΓΊΑ 5.4 ΠΡΟΑΙΡΈΤΙΚΈΣ ΛΈΙΤΟΥΡΓΙΈΣ Some optional functions of the indoor units have been added so that they can be managed from the BMS. Offset Περιγραφή Τιμές Read/Write b1 (Heating temperature compensation) Read/Write b2 (Circulation function at heating Thermo-OFF) Read/Write b4 (Change of filter cleaning period) Read/Write c5 (Static pressure selection) Read/Write...
Page 224: Κιτ Διαμορφωσησ Δικτυου
δευτερόλεπτα. Αν το LED2 τρεμοπαίζει ακόμα, επικοινωνήστε με την εξυπηρέτηση πελατών λειτουργία της Hitachi. 6 ΚΙΤ ΔΙΑΜΟΡΦΩΣΗΣ ΔΙΚΤΥΟΥ Αυτό το εξάρτημα παρέχει όλα τα απαραίτητα καλώδια για εγκαταστάτες Hitachi όταν θέτουν σε λειτουργία μια εγκατάσταση Modbus. Λίστα εξαρτημάτων: Καλώδιο USB Ανεστραμμένο καλώδιο Ethernet Μνήμη...
Page 226 Johnson Controls-Hitachi Air Conditioning Spain, S.A.U. Ronda Shimizu, 1 - Políg. Ind. Can Torrella 08233 Vacarisses (Barcelona) Spain © Copyright 2020 Johnson Controls-Hitachi Air Conditioning Spain, S.A.U. – All rights reserved. Printed in Spain...

This manual is also suitable for:

Hc-a16mb Hc-a64mb Hc-a64net

Hitachi HC-A8MB Installation And Operation Manual

Available languages

Quick Links

Related Manuals for Hitachi HC-A8MB

Summary of Contents for Hitachi HC-A8MB

This manual is also suitable for:

Table of Contents