Related Manuals for Electrolux thermaline ProThermetic PFET electric
Summary of Contents for Electrolux thermaline ProThermetic PFET electric
- Page 1 Tilting braising pan ProThermetic PFET electric Installation and operating manual * 599A1AV01 - 87.8040.01- 2022.11 *Original instructions...
- Page 2 Foreword Read the following instructions, including the warranty terms before installing and using the appliance. Visit our website www.electroluxprofessional.com and open the Support section to: Register your product Get hints & tips of your product, service and repair information The installation, use and maintenance manual (hereinafter Manual) provides the user with information necessary for correct and safe use of the appliance.
-
Page 3: Table Of Contents
Contents A WARNING AND SAFETY INFORMATION....................5 General information ........................5 Personal protection equipment ......................5 General safety ..........................6 ProThermetic general safety ......................6 Protection devices installed on the appliance ..................7 Safety signs to be placed on the appliance or near its area ..............7 Reasonably foreseeable improper use .................... - Page 4 Water filling automatic for “Sprint“ models only .................. 23 NORMAL APPLIANCE USE ........................23 Characteristics of personnel enabled to operate on the appliance ............23 Basic requirements for appliance use....................23 PRODUCT DESCRIPTION ........................23 Use ............................23 Appliance overview ........................23 Control panel ..........................
-
Page 5: Awarning And Safety Information
WARNING AND SAFETY INFORMATION General information To ensure safe use of the appliance and a proper understanding of the manual it is necessary to be familiar with the terms and typographical conventions used in the documentation. The following symbols are used in the manual to indicate and identify the various types of hazards: WARNING Danger for the health and safety of operators. -
Page 6: General Safety
Stage Protective Safety footwear Gloves Glasses Safety helmet garments ○ ● ● — — Scrapping Key: ● PPE REQUIRED ○ PPE AVAILABLE OR TO BE USED IF NECESSARY — PPE NOT REQUIRED During these operations, gloves must be cut-resistant. Failure to use the personal protection equipment by operators, specialized personnel or users can involve exposure to damage to health (depending on the model). -
Page 7: Protection Devices Installed On The Appliance
• In pressure appliances, after cooking with the lid closed, first release the pressure from the cooking chamber and do not open the lid until the pressure is completely exhausted inside the appliance. Protection devices installed on the appliance Guards The appliance has: •... -
Page 8: Transport, Handling And Storage
To preserve these conditions, the areas around the appliance must always be: • kept free of obstacles (e.g. ladders, tools, containers, boxes, etc.); • clean and dry; • well lit. For the Customer's complete information, the residual risks remaining on the appliance are indicated below: such actions are deemed improper and therefore strictly forbidden. -
Page 9: Positioning
• Do not spray water or use water jets, steam cleaner or high pressure cleaner. A.16 Preventive Maintenance In order to ensure the safety and performance of your equipment, it is recommended that service is undertaken by Electrolux Professional authorised engineers every 12 months, in accordance with Electrolux Professional Service Manuals. Please contact your local Electrolux Professional Service Centre for further details. -
Page 10: Bwarranty Terms And Exclusions
– plumbing parts, components or consumable cleaning subject to local terms and conditions. products that are not approved by the manufacturer; Check on Electrolux Professional website the list of authorized customer care. TECHNICAL DATA Data plate position... -
Page 11: How To Interpret The Factory Description
How to interpret the factory description 8 - Configuration (cont'd.) floorstanding, depth 800 mm, height 800 mm The factory description on the data plate has the following meaning: floorstanding, depth 900 mm, height 800 mm standing against the wall, depth 900 mm, height 700 mm standing against the wall, depth 900 mm, height 800 mm... -
Page 12: Dgeneral Information
Manufacturer Electrolux Professional SpA or any other personal protection equipment to be worn by operators, in service centre authorised by Electrolux compliance with regulations in force in the country of use. -
Page 13: Customer Packaging Checks
Customer packaging checks Take care when unpacking and handling of the appliance to not cause any shocks on itself. • The forwarder is responsible for the goods during transport 2. Keep all the documentation contained in the packaging. and delivery. •... -
Page 14: Dimensions
The tanks are normally cemented in the floor. 1200 1200 Freestanding Against the wall E.3.2 Dimensions 60 l 80 l 90 l 100 l 170 l 1200 1400 1200 1600 1600... -
Page 15: Installation And Connection Diagram
Installation and connection diagram Floor mounted appliances 1200 EI = Electrical connection HWI = Hot water connection D = Drain CWI = Cold water connection 60 L 80 L 90 L 1002 1038 1024 1200 1200 1200 1400 1400 1400 1200 1200 1200... - Page 16 Wall mounted appliances 1200 EI = Electrical connection HWI = Hot water connection D = Drain CWI = Cold water connection 60 L 80 L 90 L 1002 1038 1024 1200 1200 1200 1400 1400 1400 1200 1200 1200 100 L 170 L 1600 1600...
-
Page 17: Accessing The Appliance's Internal Components
Accessing the appliance’s internal components INSTALLATION AND ASSEMBLY Introduction • prearrange a device lockable in the open position for the connection to the power supply. WARNING • Do not install the unit in environments where temperatures may fall below 0℃ [32℉] or rise above 40℃ [104℉]. Refer “WARNING SAFETY INFORMATION“. -
Page 18: Installing On Plinth Or Adjustable Feet
Installing on plinth or adjustable feet Polyethylene NOTE! • Outer wrapping If installing on a steel plinth or adjustable feet, • Instructions bag always make sure these are attached to the appliance beforehand. There are no tools for taking the unit down from the transport pallet and Polypropylene putting it in place;... -
Page 19: Wall Installation
Bring the lifting cart as close as possible to the appliance. 2. Carefully turn the unit on shelf A of the truck to the horizontal position and remove the transport pallet. ø10 ø10 Wall installation F.8.1 Preparing the brackets and set up 3. -
Page 20: Sealing
1. First remove the knob, refer to paragraph E.5 Accessing 4. Reassemble the user interface panel and the front panel the appliance’s internal components. by fixing them with screws. Then remove the user interface panel and the front panel by undoing the screws at the bottom. F.10 Sealing 2. -
Page 21: Gelectrical Installation
ELECTRICAL INSTALLATION WARNING The interface for power optimization is in compliance with DIN 18875. Refer “WARNING SAFETY INFORMATION“. Power cable Unless otherwise specified, our appliances are not equipped Mains connection with a power cable. The installer must use a flexible cable having characteristics not lower than the H05RN-F rubber WARNING insulated type. -
Page 22: Mixing Tap
Mixing tap I. Fixing nut J. Gasket Install the mixing tap on the left cover, depending on the model. K. Copper pipes Model 1: Installation: 1. Fasten the clamping collar G with the fixing nut I and gasket below J on the pre-drilled hole of the left cover. 2. -
Page 23: Water Filling Automatic
Water filling automatic • Through the red knob, you can manually run hot water. The automatic water filling system, if available on your model, With hot or cold water filling option: fills up the appliance with a volume of water set by means of •... -
Page 24: Control Panel
4. USB connection Carefully pull out the spray gun handle with the hose and snap it into 5. Main switch (optional) place. Then press the button to clean 6. User interface panel the device with water. To feed the 7. Inspection panel spray gun back you have to pull the 8. -
Page 25: Main Menu
K.3.2 Main menu K.3.3.2 Set the power levels (where available) The appliance allows cooking in different cooking modes, store and recall programs. 1. Touch symbol of the temperature value Manual 2. Touch the symbol of power level on the numeric Data Monitor keypad appearing on the display;... -
Page 26: Drawer Area
NOTE! Insert Program name: To store the phase sequence in a program, tap the symbol and refer to paragraph K.3.5 Addi- ABC abc tional functions. K.3.4 Drawer area The drawer is an expansion located inside several environ- ments of the menu and includes options and functions. The lower drawer contains further settings, accessory man- agement and advanced features. -
Page 27: Programs Mode
K.3.5.5 Multizone function K.3.6 Programs mode With this option the surface of the appliance is divided into two The “Programs Mode“ allows to recall program recipes already separate heating zones, which can be operated separately or stored or to upload/download programs, from or into the together, with two different heating temperatures. -
Page 28: Start A Cooking Cycle
K.3.6.1 Guided cooking programs (if present, depending If the preheating view is on your model) enabled (refer to K.3.9 Set- tings) and available for your They are preset programs that guide you during cooking model, the display shows cycles by means of hints and pop-ups. the following screen: •... -
Page 29: End Cycle
NOTE! If B function is available for your model, enable it scroll buttons referring to K.3.9 Settings paragraph, otherwise: start/end buttons of scrolling 1. Touch the symbol to open the phases menu; Service maintenance 2. Touch the symbol to skip the current phases. This environment is only allowed to an authorized Manual Manual... - Page 30 E. Food safety H. Manual The HACCP feature allows the storage of all the set This setting allows to enable / disable the manual cooking values identifying a cooking process, and their variation, mode and its options: the cavity temperature and, when used, the food core Settings temperature at specific intervals.
-
Page 31: Alarm Messages
Touch screen calibration 2. Place the Ethernet cable inside the cable gland. This setting allows to set the calibration of the screen. • Touch the screen as close as possible to the centre of the red cross; • Repeat until the cross turns green; •... -
Page 32: Drain Tap
9. Set parameter no. 40 according to the "Parameter Setting" K.5.3 Dismounting the drain tap cover document. Settings Appliance parameters ADDR Isolated RS485 port address Minimum: Default: Maximum: 1. Hold the handle of the 2. Turn the handle com- cover and pull it gently to pletely to the right. -
Page 33: Stainless Steel Surfaces
necessary, internally) with products that are more than 90% • Do not let stainless steel parts come into prolonged contact biodegradable. with acids, spices, salts, etc. Even acid fumes which build up from cleaning tiled surfaces can promote corrosion. Use lukewarm water, a neutral detergent/cleaner if necessary, Rinse off work surfaces with fresh water. -
Page 34: Periods Of Non-Use
Periods of non-use Customer Care Service can provide advice on the best maintenance plan to be purchased based on the intensity of If the appliance is not going to be used for some time, take the use and the age of the equipment. following precautions: During service, repair and maintenance work, distractions and •... -
Page 35: Troubleshooting
IMPORTANT The appliance PNC and serial number are essential for identifying the type of appliance and date of manufacture. Troubleshooting Anomaly Possible causes Actions Alarm messages on the touch panel Internal sensor overtemperature Cool food before cooking. EOTS1 EOTS2 Internal sensor overtemperature Cool the appliance before cooking. - Page 38 Electrolux Professional AG Allmendstrasse 28 CH - 6210 Sursee www.electroluxprofessional.com...