Honeywell Virtuos 1D User Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Barcode Reader
  5. Virtuos 1D
  6. User manual
Honeywell Virtuos 1D User Manual

Honeywell Virtuos 1D User Manual

Scanner for aerpos & aermonitor
Hide thumbs
Table of Contents

Quick Links

www.virtuos.cz
hotline: +420 493 544 400
1D/2D Scanner for AerPOS & AerMonitor
User Guide
Ver 1.0
Table of Contents
loading

Related Manuals for Honeywell Virtuos 1D

Summary of Contents for Honeywell Virtuos 1D

  • Page 1 www.virtuos.cz hotline: +420 493 544 400 [email protected] 1D/2D Scanner for AerPOS & AerMonitor User Guide Ver 1.0...
  • Page 2 Scanner is located on right side. To have 1 screw M3×6 on PP series and AP series Front Angle: 80° Right Angle: 5° Rear Angle: 60° Left Angle: 5°...
  • Page 3 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.

  • Page 4: Table Of Contents

    Table of Contents Contact Customer Support Product Service and Repair ....................vii Limited Warranty ......................... vii Send Feedback ........................vii Chapter 1 - Getting Started Introduction ........................1-1 About This Manual ......................1-1 Unpacking Your Device ..................... 1-1 OEM Scan Engine Models ....................1-1 Connecting the Development Scan Engine to the PC ............
  • Page 5 RS232 Modifiers ......................2-16 RS232 Baud Rate ..................... 2-16 RS232 Word Length: Data Bits, Stop Bits, and Parity ..........2-17 RS232 Receiver Time-Out ..................2-18 RS232 Handshaking ....................2-18 RS232 Timeout ......................2-19 XON/XOFF ....................... 2-19 ACK/NAK ........................2-20 RS232 Stop Mode ..................... 2-20 Scanner to Bioptic Communication .................
  • Page 6 Poor Quality Codes ......................3-11 Poor Quality 1D Codes ..................... 3-11 Poor Quality PDF Codes ................... 3-11 Hands Free Time-Out ......................3-12 Reread Delay ........................3-12 User-Specified Reread Delay ..................3-12 2D Reread Delay ......................3-13 Illumination Lights ......................3-13 Aimer Delay ........................3-14 User-Specified Aimer Delay ..................
  • Page 7 Data Formatter ........................5-9 Primary/Alternate Data Formats ..................5-10 Chapter 6 - Symbologies All Symbologies ........................ 6-1 Message Length Description ..................... 6-1 Codabar ..........................6-2 Codabar Concatenation ....................6-3 Code 39 ..........................6-4 Code 32 Pharmaceutical (PARAF) ................6-5 Full ASCII ........................6-6 Code 39 Code Page ....................
  • Page 8 Data Matrix ........................6-37 Data Matrix Code Page ..................... 6-37 MaxiCode ........................6-38 Aztec Code ........................6-39 Aztec Code Page ...................... 6-39 Chinese Sensible (Han Xin) Code ................... 6-40 Postal Codes - 2D ......................6-41 Single 2D Postal Codes: ................... 6-41 Combination 2D Postal Codes: .................
  • Page 9 Troubleshooting ......................10-1 Appendix A - Reference Charts Symbology Charts .......................A-1 Linear Symbologies .......................A-1 2D Symbologies......................A-3 Postal Symbologies .......................A-3 ASCII Conversion Chart (Code Page 1252)................A-3 Lower ASCII Reference Table.....................A-4 ISO 2022/ISO 646 Character Replacements ..............A-8 Keyboard Key References....................A-10 Sample Symbols Programming Chart...

  • Page 10: Contact Customer Support

    Support. Contact your service center to obtain a Return Material Authorization number (RMA #) before you return the product. To obtain warranty or non-warranty service, return your product to Honeywell (postage paid) with a copy of the dated pur- chase record.Limited Warranty...
  • Page 11 viii...

  • Page 12: Chapter 1 - Getting Started

    This User’s Guide provides demonstration, installation, and programming instructions for the N36XX scan engine. Honeywell’s bar code scan engines are factory programmed for the most common terminal and communications settings. If you need to change these setting, programming is accomplished by scanning the bar codes in this guide.

  • Page 13: Connecting The Development Scan Engine To The Pc

    Connecting the Development Scan Engine to the PC The development OEM scan engine can connect to a PC for evaluation. Connecting with USB Note: The N3680XX-XX-USB scan engine will only communicate USB through the 10 pin modular connector. 1. Turn off power to the terminal/computer. 2.

  • Page 14: Connecting With Rs232 Serial Port

    Connecting with RS232 Serial Port 1. If using an RS-232 connection, connect the serial interface cable to the interface board and to the matching port on the back of the computer. 2. Connect the power supply connector to the serial interface cable. Plug in the power supply. 3.
  • Page 15 5. Verify the scan engine operation by scanning a bar code from the Sample Symbols in the back of this manual. The scan engine beeps once when a bar code is successfully decoded. To connect an scan engine to your host system, refer to the N36XX Integration Manual. 1 - 4...

  • Page 16: Reading Techniques

    Honeywell scan engines are programmed by scanning menu bar codes or by sending serial commands to the scan engine. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Contact your Honeywell OEM representative for more information.

  • Page 17: Resetting The Custom Defaults

    you want the beeper volume set to High, just scan the Set Custom Defaults bar code, then scan the Beeper Volume High menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be updated.

  • Page 18: Chapter 2 - Programming The Interface

    Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scan engine set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. RS232 Serial Port The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal.

  • Page 19: Usb Serial

    Scan the following code to program the scan engine to emulate a regular RS232-based COM Port. If you are using a Mic- rosoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scan engine as a USB CDC class device and automatically use a class driver.

  • Page 20: Keyboard Country Layout

    Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language. As a general rule, the following characters are supported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~ Keyboard Countries * United States Albania...
  • Page 21 Keyboard Countries (Continued) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands)
  • Page 22 Keyboard Countries (Continued) Estonia Faroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) 2 - 11...
  • Page 23 Keyboard Countries (Continued) Kazakh Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy Japan ASCII...
  • Page 25 Keyboard Countries (Continued) Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) Norway 2 - 10...
  • Page 26 Keyboard Countries (Continued) Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) Serbia (Cyrillic) Serbia (Latin) 2 - 11...
  • Page 27 Keyboard Countries (Continued) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar Turkey F 2 - 12...

  • Page 28: Keyboard Style

    Keyboard Countries (Continued) Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United Stated (Dvorak right) United States (International) Uzbek (Cyrillic) Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Keyboard Style settings.

  • Page 29: Keyboard Conversion

    Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards). Shift Lock Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off.

  • Page 30: Control Character Output

    Control Character Output This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page 1252) on page A-3.

  • Page 31: Rs232 Modifiers

    * Turbo Mode Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off Numeric Keypad Mode On * Numeric Keypad Mode Off Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters.

  • Page 32: Rs232 Word Length: Data Bits, Stop Bits, And Parity

    2400 4800 9600 19200 38400 57,600 * 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.

  • Page 33: Rs232 Receiver Time-Out

    7 Data, 2 Stop, Parity Even 7 Data, 2 Stop Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires.

  • Page 34: Rs232 Timeout

    Flow Control with Timeout: The scan engine asserts RTS when it has data to send and waits for a delay (see RS232 Timeout on page 2-19) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the device transmit buffer is cleared and scanning may resume.

  • Page 35: Ack/Nak

    Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scan engines and bioptic scanners. Note: The scan engine’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.

  • Page 36: Scanner-Bioptic Ack/Nak Mode

    Scanner-Bioptic ACK/NAK Mode Bioptic ACK/Nak On must be scanned so the scan engine will wait for an ACK or NAK from a bioptic scanner after each packet is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response. Default = Bioptic ACK/NAK Off.
  • Page 37 2 - 22...

  • Page 38: Chapter 3 - Input/Output Settings

    Input/Output Settings Power Up Beeper The scan engine can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner. Power Up Beeper Off - Scanner * Power Up Beeper On - Scanner...

  • Page 39: Good Read And Error Indicators

    Good Read and Error Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = Beeper - Good Read On. Beeper - Good Read Off * Beeper - Good Read On Beeper Volume –...

  • Page 40: Beeper Pitch - Error

    High (4200 Hz) Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scan engine emits when there is a bad read or error. Default = Razz. * Razz (250 Hz) Medium (3250 Hz) High (4200 Hz) Beeper Duration –...

  • Page 41: Number Of Beeps - Good Read

    Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read.

  • Page 42: Manual Trigger Mode

    Manual Trigger Mode When in manual trigger mode, the scanner scans until a bar code is read, or until the trigger is released. Manual Trigger - Normal LED Illumination - Manual Trigger If you wish to set the illumination LED brightness, scan one of the bar codes below. This sets the LED illumination for the scan engine when the trigger is pressed.

  • Page 43: End Character Activation After Good Read

    End Character Activation After Good Read After a bar code is successfully detected and read from the scanner, the illumination can be programmed either to remain on and scanning, or to turn off. When End Character Activation After Good Read is enabled, the illumination turns off and stops scanning after a good read.

  • Page 44: Deactivation Character

    Deactivation Character This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion Chart (Code Page 1252), page A-3, find the hex value that represents the character you want to use to terminate scanning. Scan the following bar code, then use the Programming Chart inside the back cover of this manual to read the alphanu-...

  • Page 45: Idle Illumination - Presentation Mode

    Idle Illumination - Presentation Mode Scan one of the bar codes below to set the LED illumination for the scanner when it is in an idle state in Presentation Mode. Default = High. Note: If you use one of the lower Idle Illumination settings, and there is not enough ambient light, the scanner may have difficulty detecting when a bar code is presented to it.
  • Page 46 100% Note: A bar code needs only to be touched by the centering window in order to be read. It does not need to pass completely through the centering window. 3 - 9...

  • Page 47: Codegate

    Scan Presentation Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual.

  • Page 48: Mobile Phone Read Mode

    CodeGate On Out-of-Stand Mobile Phone Read Mode When this mode is selected, your scanner is optimized to read bar codes from mobile phone or other LED displays. However, the speed of scanning printed bar codes may be slightly lower when this mode is enabled. Hand Held Scanning - Mobile Phone Presentation Scanning -...

  • Page 49: Hands Free Time-Out

    * Poor Quality PDF Reading Off Hands Free Time-Out The Scan Stand and Presentation Modes are referred to as “hands free” modes. If the scanner’s trigger is pulled when using a hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual trig- ger mode by setting the Hands Free Time-Out.

  • Page 50: 2D Reread Delay

    2D Reread Delay Sometimes 2D bar codes can take longer to read than other bar codes. If you wish to set a separate Reread Delay for 2D bar codes, scan one of the programming codes that follows. 2D Reread Delay Off indicates that the time set for Reread Delay used for both 1D and 2D bar codes.

  • Page 51: Aimer Delay

    Aimer Delay The aimer delay allows a delay time for the operator to aim the scan engine before the picture is taken. Use these codes to set the time between when the trigger is pulled and when the picture is taken. During the delay time, the aiming light will appear, but the LEDs won’t turn on until the delay time is over.

  • Page 52: Centering

    Centering Use Centering to narrow the scan engine’s field of view to make sure that when the scanner is hand-held, it reads only those bar codes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the desired codes are read.

  • Page 53: Output Sequence Overview

    Top of Centering Window Bottom of Centering Window Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scan engine to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the Default Sequence symbol programs the scan engine to the Universal values, shown below.
  • Page 54 Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example. A - Code 39 B - Code 128 C - Code 93...

  • Page 55: Output Sequence Editor

    termination string for third code Output Sequence Editor Enter Sequence Default Sequence Partial Sequence If an output sequence operation is terminated before all your output sequence criteria are met, the bar code data acquired to that point is a “partial sequence.” Scan Discard Partial Sequence to discard partial sequences when the output sequence operation is terminated before completion.

  • Page 56: Multiple Symbols

    Multiple Symbols When this programming selection is turned On, it allows you to read multiple symbols with a single pull of the scanner’s trigger. If you press and hold the trigger, aiming the scanner at a series of symbols, it reads unique symbols once, beeping (if turned on) for each read.

  • Page 57: Working Orientation

    * Video Reverse Off Working Orientation Some bar codes are direction-sensitive. For example, KIX codes can misread when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner. Default = Upright.

  • Page 58: Chapter 4 - Data Editing

    Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.

  • Page 59: To Clear One Or All Prefixes Or Suffixes

    Example: Add a Tab Suffix to All Symbologies Step 1. Scan Add Suffix. Step 2. Scan 9, 9 from the Programming Chart inside the back cover of this manual to apply this suffix to all symbologies. Step 3. Scan 0, 9 from the Programming Chart inside the back cover of this manual.

  • Page 60: Function Code Transmit

    Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scan engine transmits the func- tion code to the terminal. Charts of these function codes are provided in ASCII Conversion Chart (Code Page 1252) starting on page...

  • Page 61: Interfunction Delay

    Next, scan the Character to Trigger Delay bar code, then the 2-digit hex value for the ASCII character that will trigger the delay ASCII Conversion Chart (Code Page 1252), beginning on page A-3. Delay Length Character to Trigger Delay To remove this delay, scan the Delay Length bar code, and set the number of delays to 0. Scan the Save bar code using Programming Chart inside the back cover of this manual.

  • Page 62: Chapter 5 - Data Formatting

    Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scan engine’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.

  • Page 63: Other Programming Selections

    Step 5. Length Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length from the Programming Chart inside the back cover of this manual. For example, 50 characters is entered as 0050. Note: 9999 indicates all lengths.

  • Page 64: Terminal Id Table

    Terminal ID Table Terminal Model(s) Terminal ID PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop Serial RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) Keyboard PS2 compatibles AT compatibles Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your input data string.
  • Page 65 F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 1234567890 ABCDEFGHIJ Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,”...

  • Page 66: Move Commands

    Move Commands Move the cursor forward a number of characters F5 Move the cursor ahead “nn” characters from current cursor position. Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead. F5 Example: Move the cursor forward and send the data Move the cursor forward 3 characters, then send the rest of the bar code data from the bar code above.

  • Page 67: Search Commands

    Search Commands Search forward for a character F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F8xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.

  • Page 68: Miscellaneous Commands

    Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command.
  • Page 69 The data is output as: 1234 5678 Stop replacing characters E5 Terminates character replacement. Syntax = E5. Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position.

  • Page 70: Data Formatter

    Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation.a Data Formatter When Data Formatter is turned Off, the bar code data is output to the host as read, including prefixes and suffixes.

  • Page 71: Primary/Alternate Data Formats

    Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the bar codes below. Primary Data Format Data Format 1 Data Format 2...

  • Page 72: All Symbologies

    Symbologies This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) • Matrix 2 of 5 •...

  • Page 73: Codabar

    EXAMPLE: Decode only those bar codes with a count of 15 characters. Min. length = 15Max. length = 15 For a value other than the minimum and maximum message length defaults, scan the bar codes included in the explanation of the symbology, then scan the digit value of the message length and Save bar codes on the Programming Chart inside the back...

  • Page 74: Codabar Concatenation

    Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D”...

  • Page 75: Code 39

    Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Code 39 Check Character...

  • Page 76: Code 32 Pharmaceutical (Paraf)

    Code 39 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 0-48. Minimum Default = 0, Maximum Default = 48. Minimum Message Length Maximum Message Length Code 39 Append This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to...

  • Page 77: Full Ascii

    Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.

  • Page 78: Interleaved 2 Of 5

    Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.

  • Page 79: Nec 2 Of 5

    Maximum Message Length NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.
  • Page 80 NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93...

  • Page 81: Code 93 Code Page

    Code 93 Append This function allows the scanner to append the data from several Code 93 bar codes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 93 bar codes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data.

  • Page 82: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)

    Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information.

  • Page 83: Straight 2 Of 5 Iata (Two-Bar Start/Stop)

    Straight 2 of 5 IATA (two-bar start/stop) Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information.

  • Page 84: Matrix 2 Of 5

    Matrix 2 of 5 Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information.

  • Page 85: Code 11

    Code 11 Code 11 On/Off * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit * Two Check Digits Code 11 Message Length Scan the bar codes below to change the message length.

  • Page 86: Code 128

    Code 128 Code 128 On/Off * On ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood informa- tion in a uniform manner. The use of ISBT formats requires a paid license. The ISBT 128 Application Specification describes 1) the critical data elements for labeling blood products, 2) the current recommendation to use Code 128 due to its high degree of security and its space-efficient design, 3) a variation of Code 128 that supports concatenation of neigh- boring symbols, and 4) the standard layout for bar codes on a blood product label.

  • Page 87: Code 128 Code Page

    Code 128 Append This function allows the scanner to append the data from several Code 128 bar codes together before transmitting them to the host computer. When the scanner encounters a Code 128 bar code with the append trigger character(s), it buffers Code 128 bar codes until it reads a Code 128 bar code that does not have the append trigger.

  • Page 88: Gs1-128

    GS1-128 GS1-128 On/Off * On GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80. Minimum Message Length Maximum Message Length UPC-A...
  • Page 89 UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it.

  • Page 90: Upc-A/Ean-13 With Extended Coupon Code

    UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 6-18. Default = Not Required. Required * Not Required UPC-A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda.

  • Page 91: Coupon Gs1 Databar Output

    Coupon GS1 DataBar Output If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1 DataBar code. Scan the GS1 Output On code below to scan and output only the GS1 DataBar code data. Default = GS1 Out- put Off.
  • Page 92 UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Required * Not Required UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space.

  • Page 93: Upc-E1

    UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off UPC-E1 Most U.P.C.

  • Page 94: Ean/Jan-13

    EAN/JAN-13 EAN/JAN-13 On/Off * On Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A. UPC-A Converted to EAN-13 * Do not Convert UPC-A EAN/JAN-13 Check Digit...
  • Page 95 EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-13 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda.

  • Page 96: Isbn Translate

    ISBN Translate When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off. * Off EAN/JAN-8 EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
  • Page 97 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda.

  • Page 98: Msi

    MSI On/Off * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
  • Page 99 Validate Type 11 then Type 10 Character and Transmit Disable MSI Check Characters MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length 6 - 28...

  • Page 100: Gs1 Databar Omnidirectional

    GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On 6 - 29...

  • Page 101: Gs1 Databar Expanded

    GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information.

  • Page 102: Codablock F

    Codablock A Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600. Minimum Message Length Maximum Message Length Codablock F ...

  • Page 103: Pdf417

    PDF417 < Default All PDF417 Settings > PDF417 On/Off * On PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750. Minimum Message Length Maximum Message Length MacroPDF417...

  • Page 104: Micropdf417

    MicroPDF417 < Default All MicroPDF417 Settings > MicroPDF417 On/Off * Off MicroPDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366. Minimum Message Length Maximum Message Length GS1 Composite Codes...

  • Page 105: Upc/Ean Version

    UPC/EAN Version Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols that have a U.P.C. or an EAN linear compo- nent. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Ver- sion Off.

  • Page 106: Tcif Linked Code 39 (Tlc39)

    GS1 DataBar Emulation GS1 Code Expansion Off EAN8 to EAN13 Conversion * GS1 Emulation Off TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar code readers are capable of reading the Code 39 linear component.

  • Page 107: Qr Code Page

    QR Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089. Minimum Message Length Maximum Message Length QR Code Append This function allows the scanner to append the data from several QR Code bar codes together before transmitting them to...

  • Page 108: Data Matrix

    Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116. Minimum Message Length Maximum Message Length Data Matrix Append...

  • Page 109: Maxicode

    codes were created (see ISO 2022/ISO 646 Character Replacements on page A-8), and scan the value and the Save bar code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.

  • Page 110: Aztec Code

    Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Aztec Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832. Minimum Message Length Maximum Message Length Aztec Append...

  • Page 111: Chinese Sensible (Han Xin) Code

    codes were created (see ISO 2022/ISO 646 Character Replacements on page A-8), and scan the value and the Save bar code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.

  • Page 112: Postal Codes - 2D

    Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed. Only one 2D postal code selection can be active at a time. If you scan a second 2D postal code selection, the first selection is overwritten. Default = 2D Postal Codes Off.

  • Page 113: Combination 2D Postal Codes

    Postnet On Also see Postnet Check Digit, page 6-44. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British Post On Intelligent Mail Bar Code and Postnet with B and B’ Fields On Postnet and Postal-4i On Postnet and Intelligent Mail Bar Code On...
  • Page 114 Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and Intelligent Mail Bar Code On Planet Code, Postnet, and Postal-4i On Planet Code, Postnet, and Intelligent Mail Bar Code On Planet Code, Postal-4i, and Intelligent Mail Bar Code On Postnet,...
  • Page 115 Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet On Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet with B and B’ Fields On Planet Code Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default = Don’t Transmit.

  • Page 116: Postal Codes - Linear

    Combination C and N Tables causes the field to be interpreted using either the C or N Tables. * Bar Output Numeric N Table Alphanumeric C Table Combination C and N Tables Postal Codes - Linear The following lists linear postal codes. Any combination of linear postal code selections can be active at a time. China Post (Hong Kong 2 of 5) ...

  • Page 117: Korea Post

    Maximum Message Length Korea Post Korea Post * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for addi- tional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Korea Post Check Digit...

  • Page 118: Chapter 7 - Imaging Commands

    Imaging Commands The scan engine is like a digital camera in the way it captures, manipulates, and transfers images. The following commands allow you to alter the way the scan engine performs these functions. Note: If you are using the scan engine in a stand, you must set the In-Stand Sensor Mode to Off in order to take images (see Presentation Centering on page 3-8).
  • Page 119 1B Sounds a beep when the image is captured. T - Wait for Trigger Waits for a hardware button push before taking the image. This is only available when using Photo Style (1P). 0T Takes image immediately (default) 1T Waits for a button push, then takes the image L - LED State Determines if the LEDs should be on or off, and when.

  • Page 120: Image Ship - Imgshp

    W - Target White Value Sets the target for the median grayscale value in the captured image. For capturing close-up images of high contrast docu- ments, a lower setting, such as 75, is recommended. Higher settings result in longer exposure times and brighter images, but if the setting is too high, the image may be overexposed.
  • Page 121 Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with IMGSNP Modifiers (page 7-1). 0A Infinity filter off (default) 1A Infinity filter on Example of Infinity Filter off (0A) Example of Infinity Filter on (1A) from approximately 12 feet from approximately 12 feet (3.66m)
  • Page 122 E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen fil- ter can be entered from 1 to 24.
  • Page 123 1iy Invert around the Y axis (flips picture left to right) Example of image not Example of image Example of image inverted: with Invert Image set to with Invert Image set 1ix: to 1iy: IF- Noise Reduction Used to reduce the salt and pepper noise in an image. 0if No salt and pepper noise reduction (default) 1if Salt and pepper noise reduction Example of Noise Reduction Off (0if):...
  • Page 124 IR - Image Rotate 0ir Image as snapped (rightside up) (default) 1ir Rotate image 90 degrees to the right 2ir Rotate image 180 degrees (upside down) 3ir Rotate image 90 degrees to the left Example of Image Rotate set to 2ir: Example of Image Rotate set to 0ir: Example of Image Rotate set to 1ir: Example of Image Rotate set to 3ir:...
  • Page 125 nL The left edge of the shipped image corresponds to column n of the image in memory. Range: 000 - 843. (Default = 0) nR The right edge of the shipped image corresponds to column n - 1 of the image in memory. Range: 000 - 843. (Default = all columns) nT The top edge of the shipped image corresponds to row n of the image in memory.
  • Page 126 3S ship every 3rd pixel, both horizontally and vertically Example of Pixel Ship set to 1S: Example of Pixel Example of Pixel Ship set to 2S: Ship set to 3S: U - Document Image Filter Allows you to input parameters to sharpen the edges and smooth the area between the edges of text in an image. This filter should be used with gamma correction (see page 7-7), with the scan engine in a stand, and the image captured using the...
  • Page 127 1W Ship histogram Image used for histogram: Histogram of image at left: 7 - 10...

  • Page 128: Chapter 8 - Utilities

    Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.

  • Page 129: Test Menu

    Note: EZConfig-Scanning requires .NET software. If .NET is not installed on your PC, you will be prompted to install it during the EZConfig-Scanning installation. 1. Access the Honeywell web site at www.honeywellaidc.com 2. Click on the Products tab. Under Software, select Device Management.

  • Page 130: Resetting The Factory Defaults

    7. Using Explorer, go to the c:\windows\temp file. 8. Double click on the Setup.exe file. Follow the screen prompts to install the EZConfig-Scanning program. 9. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfig- Scanning and select EZConfig for your browser.
  • Page 131 8 - 4...

  • Page 132: Chapter 9 - Serial Programming Commands

    IMPORTANT: The scan engine’s flash has a limited number of write cycles. When sending commands fre- quently Honeywell recommends using the volatile ( exclamation point) memory as often as possible.

  • Page 133: Responses

    :Name: Field Usage (Optional) This command returns the query information from the scan engine. Tag Field Usage When a query is used in place of a Tag field, the query applies to the entire set of commands available for the particular storage table indicated by the Storage field of the command.

  • Page 134: Trigger Commands

    CK20[ACK], CCT1[ACK], MIN2[ACK], MAX60[ACK], DFT[ACK]. This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; the Check Character (CK2) is set to 0, or Not Required; concatenation (CCT) is set to 1, or Enabled;...

  • Page 135: Menu Commands

    ACK/NAK Mode On USBACK1 ACK/NAK Mode Off* USBACK0 Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Bioptic Aux Port PAPMAG NCR Bioptic Aux Port PAPNCR Wincor Nixdorf Terminal PAPWNX Wincor Nixdorf Beetle...
  • Page 136 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Denmark KBDCTY8 Dutch (Netherlands) KBDCTY11 Estonia KBDCTY41 Faroese KBDCTY83 Finland KBDCTY2 France KBDCTY3 Gaelic KBDCTY84 Germany KBDCTY4 Greek KBDCTY17 Greek (220 Latin) KBDCTY64 Greek (220) KBDCTY61 Greek (319 Latin) KBDCTY65 Greek (319) KBDCTY62...
  • Page 137 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry KBDCTY21 2-11 Serbia (Cyrillic) KBDCTY37 2-11 Serbia (Latin) KBDCTY36 2-11 Slovakia KBDCTY22 2-12 Slovakia (QWERTY) KBDCTY49 2-12 Slovakia (QWERTZ) KBDCTY48 2-12 Slovenia KBDCTY31 2-12 Spain KBDCTY10 2-12 Spanish variation KBDCTY51 2-12...
  • Page 138 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Turbo Mode On KBDTMD1 2-15 *Numeric Keypad Off KBDNPS0 2-16 Numeric Keypad On KBDNPS1 2-16 *Auto Direct Connect Off KBDADC0 2-16 Auto Direct Connect On KBDADC1 2-16 Baud Rate 300 BPS 232BAD0...
  • Page 139 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Input/Output Selections Power Up Beeper Power Up Beeper Off - Scanner BEPPWR0 *Power Up Beeper On - Scanner BEPPWR1 Beep on BEL Character Beep on BEL On BELBEP1 *Beep on BEL Off BELBEP0...
  • Page 140 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry HSTDEN1 Deactivation Character *14 [DC4] HSTDCH Serial Trigger Mode Read Time-Out TRGSTO#### (0 - 300,000 ms) *30,000 Presentation Mode Presentation Mode PAPPST Idle Illumination PWRIDL0 PWRIDL50 Presentation Sensitivity Range 0-20 (*1) TRGPMS Presentation Centering...
  • Page 141 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Centering Window Centering On DECWIN1 3-15 *Centering Off DECWIN0 3-15 Top of Centering Window (*40%) DECTOP### 3-16 Bottom of Centering Window (*60%) DECBOT### 3-16 Output Sequence Editor Enter Sequence SEQBLK 3-18...
  • Page 142 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Data Formatter Data Formatter Off DFM_EN0 *Data Formatter On, DFM_EN1 Not Required, Keep Prefix/Suffix Data Format Required, DFM_EN2 Keep Prefix/Suffix Data Formatter On, DFM_EN3 Not Required, Drop Prefix/Suffix Data Format Required, DFM_EN4 Drop Prefix/Suffix...
  • Page 143 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Code 39 Append *Off C39APP0 C39APP1 Code 32 Pharmaceutical (PARAF) *Off C39B320 C39B321 Code 39 Full ASCII *Off C39ASC0 C39ASC1 Code 39 Code Page C39DCP Interleaved 2 of 5 Default All Interleaved I25DFT 2 of 5 Settings...
  • Page 144 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Straight 2 of 5 IATA Default All Straight 2 of 5 IATA A25DFT 6-12 Settings *Off A25ENA0 6-12 A25ENA1 6-12 Straight 2 of 5 IATA Message Length Minimum (1 - 48) *4 A25MIN## 6-12...
  • Page 145 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry UPC-A 2 Digit Addenda *Off UPAAD20 6-18 UPAAD21 6-18 UPC-A 5 Digit Addenda *Off UPAAD50 6-18 UPAAD51 6-18 UPC-A Addenda Required *Not Required UPAARQ0 6-19 Required UPAARQ1 6-19 UPC-A Addenda UPAADS0...
  • Page 146 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry EAN/JAN-13 2 Digit Addenda 2 Digit Addenda On E13AD21 6-24 *2 Digit Addenda Off E13AD20 6-24 5 Digit Addenda On E13AD51 6-24 *5 Digit Addenda Off E13AD50 6-24 EAN/JAN-13 Addenda Required *Not Required...
  • Page 147 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry GS1 DataBar Limited Default All GS1 DataBar Limited Settings RSLDFT 6-29 RSLENA0 6-29 RSLENA1 6-29 GS1 DataBar Expanded Default All GS1 DataBar RSEDFT 6-30 Expanded Settings RSEENA0 6-30 RSEENA1 6-30...
  • Page 148 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry GS1 Emulation GS1-128 Emulation EANEMU1 6-34 GS1 DataBar Emulation EANEMU2 6-35 GS1 Code Expansion Off EANEMU3 6-35 EAN8 to EAN13 Conversion EANEMU4 6-35 *GS1 Emulation Off EANEMU0 6-35 TCIF Linked Code 39 T39ENA1...
  • Page 149 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Single 2D Postal Codes Australian Post On POSTAL1 6-41 British Post On POSTAL7 6-41 Canadian Post On POSTAL30 6-41 Intelligent Mail Bar Code On POSTAL10 6-41 Japanese Post On POSTAL3 6-41 KIX Post On...
  • Page 150 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Postnet Check Digit Transmit NETCKX1 6-44 *Don’t Transmit NETCKX0 6-44 Australian Post Interpretation Bar Output AUSINT0 6-45 Numeric N Table AUSINT1 6-45 Alphanumeric C Table AUSINT2 6-45 Combination N and C Tables AUSINT3 6-45...
  • Page 151 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry *Compensation Off IMGCOR0 Compensation On IMGCOR1 *Pixel Depth - 8 bits/pixel (grayscale) IMGBPP8 Pixel Depth - 1 bit/pixel (B&W) IMGBPP1 *Don’t Sharpen Edges IMGEDG0 Sharpen Edges (0-23) IMGEDG## *File Format - JPEG IMGFMT6...
  • Page 152 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Ship Histogram IMGHST1 Utilities Add Code I.D. Prefix to All Symbologies (Temporary) PRECA2,BK2995C80! Show Decoder Revision REV_DR Show Scan Driver Revision REV_SD Show Software Revision REVINF Show Data Format DFMBK3? Test Menu TSTMNU1...
  • Page 153 9 - 22...

  • Page 154: Chapter 10 - Maintenance And Troubleshooting

    Inspecting Cords and Connectors Inspect the scan engine’s interface cable and connector for wear or other signs of damage. A badly worn cable or damaged connector may interfere with scan engine operation. Contact your Honeywell distributor for information about cable replace- ment.
  • Page 155 10 - 2...

  • Page 156: Symbology Charts

    Refer to Data Editing beginning on page 4-1 and Data Formatting beginning on page 5-1 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...
  • Page 157 Honeywell Possible modifiers Symbology UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity A - 2...

  • Page 158: 2D Symbologies

    2D Symbologies Honeywell Possible modifiers Symbology All Symbologies Aztec Code 0-9, A-C Chinese Sensible Code (Han Xin Code) Codablock A 0, 1, 4, 5, 6 Codablock F 0, 1, 4, 5, 6 Code 49 0, 1, 2, 4 Data Matrix...

  • Page 159: Lower Ascii Reference Table

    U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings. Non-printable ASCII control Keyboard Control + ASCII (CTRL+X) Mode characters Windows Mode Control + X Mode On (KBDCAS2) Control + X Mode Off (KBDCAS0) Char CTRL + X CTRL + X function Reserved CTRL+ @...
  • Page 160 Printable Characters (Continued) Character Character Character & < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ € Ç 0x48 up arrow ↓ ü 0x50 down arrow → ‚ é 0x4B right arrow ← ƒ â...
  • Page 161 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code ” ö 0x3F • ò 0x40 – û 0x41 — ù 0x42 ˜ ÿ 0x43 ™ Ö 0x44 š Ü 0x57 › ¢ 0x58 œ £ Numeric Keypad + 0x4E ¥...
  • Page 162 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code ╚ È ╔ É ╩ Ê ╦ Ë ╠ Ì ═ Í ╬ Î ╧ Ï ╨ Ð ╤ Ñ ╥ Ò ╙ Ó ╘ Ô ╒ Õ ╓...

  • Page 163: Iso 2022/Iso 646 Character Replacements

    (standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
  • Page 164 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ¥ ⎯ ¥ ⎯ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...

  • Page 165: Keyboard Key References

    Keyboard Key References 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 4B 50 55 5A 5F 64 69 5B 60 65 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 1F 20 21 22 23 24 25 26 27 28 29 2B...

  • Page 166: Sample Symbols

    Sample Symbols UPC-A 0 123456 7890 Interleaved 2 of 5 1234567890 EAN-13 9 780330 290951 Code 128 Code 128 Code 39 Codabar BC321 A13579B Code 93 123456-9$ Straight 2 of 5 Industrial 123456 Matrix 2 of 5 RSS-14 6543210 (01)00123456789012...
  • Page 167 Sample Symbols PDF417 Car Registration Postnet QR Code Zip Code Data Matrix Numbers Test Symbol Aztec MaxiCode Package Label Micro PDF417 Test Message Test Message...

  • Page 168: Programming Chart

    Programming Chart...
  • Page 169 Programming Chart Save Discard Reset If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.

This manual is also suitable for:

Virtuos 2d

Table of Contents