Page 1 Xenon™ XP 195X Series Area-Imaging Scanners and Bases Scanner Models: 1950g, 1950h, 1952g, 1952h, 1952g-BF, 1952h-BF Base Models: CCB01-010BT, CCB01-010BT-BF, CCB-H-010BT, CCB-H-010BT-BF User Guide...
Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. HII makes no representation or warranties regarding the information provided in this publication.
Page 3: Table Of Contents
TABLE OF CONTENTS Customer Support ........................xvii Technical Assistance ......................xvii Product Service and Repair ..................... xvii Limited Warranty ......................... xvii Chapter 1 - Get Started ..................1 About This Manual......................... 1 Unpack Your Device........................1 Connect the Device........................2 Connect with USB........................
Page 4 CTS/RTS Emulation ......................19 ACK/NAK Mode........................19 ® Verifone Ruby Terminal......................19 ® Gilbarco Terminal........................20 Honeywell Bioptic Aux Port .....................20 ® Datalogic™ Magellan Aux Port....................20 Wincor Nixdorf Terminal ......................21 Wincor Nixdorf Beetle™ Terminal ..................21 Wincor Nixdorf RS232 Mode A....................22 Keyboard Country Layout......................22 Keyboard Wedge Modifiers......................29 ALT Mode ..........................29...
Page 5 Scanner to Bioptic Communication ..................38 Scanner-Bioptic Packet Mode..................38 Scanner-Bioptic ACK/NAK Mode..................39 Scanner-Bioptic ACK/NAK Timeout ................39 Chapter 3 - Cordless System Operation .............41 How the Cordless Charge Base/Access Point Works.............41 Link the Scanner to a Charge Base..................41 Link the Scanner to an Access Point ..................42 Replace a Linked Scanner ......................42 Communication Between the Cordless System and the Host...........................42...
Page 6 Low Power Alert Repeat ......................51 Low Power Alert Beep ......................52 Reset Scanner ..........................52 Scan While in Base Cradle......................52 Base Charge Modes........................53 Page ..............................54 Page Mode ..........................54 Page Pitch ..........................54 Error Indicators..........................55 Beeper Pitch - Base Error....................55 Number of Beeps - Base Error ..................55 Scanner Report..........................56 Scanner Address ..........................56 Base or Access Point Address ....................56...
Page 7 Delete Last Code........................67 Clear All Codes........................67 Transmit Records to Host....................67 Batch Mode Transmit Delay ....................67 Multiple Scanner Operation ....................68 Scanner Name..........................68 Application Work Groups ......................69 Application Work Group Selection..................70 Reset the Factory Defaults: All Application Work Groups ..........70 Reset the Custom Defaults: All Application Work Groups ...........71 Use the Scanner with Bluetooth Devices................71 Bluetooth Secure Simple Pairing (SSP)................71 Bluetooth HID Keyboard Connect...................72...
Page 8 Good Read and Error Indicators ....................82 Beeper – Good Read......................82 Beeper Volume – Good Read ....................83 Beeper Pitch – Good Read ....................83 Vibrate – Good Read......................84 Beeper Pitch – Error ......................84 Beeper Duration – Good Read..................85 LED – Good Read ........................85 Number of Beeps –...
Page 9 Activation Character......................97 End Character Activation After Good Read ..............97 Character Activation Timeout...................98 Character Deactivation......................98 Deactivation Character .......................98 Illumination Lights ........................99 Aimer Delay.............................99 User-Specified Aimer Delay....................100 Aimer Mode ..........................100 Centering............................100 Single Code Centering......................101 Custom Centering ......................101 Preferred Symbology .......................102 High Priority Symbology....................103 Low Priority Symbology ....................103 Preferred Symbology Time-out..................104 Preferred Symbology Default ..................104...
Page 10 Very Low Beeper (Nighttime Mode)................118 Low Beeper (Daytime Mode) ..................119 Quiet Operations - LED and Volume Settings .............. 119 Linking LED Colors and Sound ..................119 Number of LED Flashes ....................120 LED Flash Rate........................120 LED Solid (No Flash)......................121 Page Volume Control ......................
Page 11 Data Format Editor Commands ..................134 Send Commands ........................134 Move Commands........................140 Search Commands......................141 Miscellaneous Commands .....................144 Data Formatter...........................147 Data Format Non-Match Error Tone................148 Primary/Alternate Data Formats ..................149 Single Scan Data Format Change................149 Chapter 8 - Symbologies................151 All Symbologies..........................152 Message Length Description ....................152 Codabar............................152 Code 39 ............................155 Interleaved 2 of 5........................158...
Page 12 ISBN Translate........................185 EAN/JAN-8 ..........................185 MSI..............................187 GS1 DataBar Omnidirectional..................... 189 GS1 DataBar Limited ......................190 GS1 DataBar Expanded ......................190 Trioptic Code..........................191 Codablock A ..........................191 Codablock F ..........................192 Label Code........................... 193 PDF417............................193 MacroPDF417..........................194 MicroPDF417 ..........................
Page 13 Chapter 9 - Imaging Commands ...............215 Single-Use Basis ........................215 Command Syntax........................215 Image Snap - IMGSNP......................216 IMGSNP Modifiers ......................216 Image Ship - IMGSHP ......................219 IMGSHP Modifiers ......................220 Image Size Compatibility....................227 Intelligent Signature Capture - IMGBOX.................228 Signature Capture Optimize ..................228 IMGBOX Modifiers ......................229 RF Default Imaging Device ....................233 Chapter 10 - Utilities ...................235 To Add a Test Code I.D.
Page 14 Chapter 12 - Product Specifications............275 Xenon XP 1950g/1950h Corded Scanner Product Specifications ...... 275 Xenon XP 1952g/1952h Cordless Scanner Product Specifications ....276 Xenon XP 1952g-BF/1952h-BF Scanner Product Specifications ....... 278 CCB01-010BT/CCB01-010BT-BF Charge Base Product Specifications ......................279 CCB-H-010BT/CCB-H-010BT-BF Charge Base Product Specifications ......................
Page 15 Change a Scanner Battery ....................294 Troubleshoot a Corded Scanner..................294 Troubleshoot a Cordless System..................295 Troubleshoot a Base ......................295 Troubleshoot a Cordless Scanner ................295 Chapter A - Reference Charts ..............297 Symbology Charts........................297 Linear Symbologies ......................297 2D Symbologies ........................298 Postal Symbologies ......................299 ASCII Conversion Chart (Code Page 1252) ..............300 Lower ASCII Reference Table....................301 ISO 2022/ISO 646 Character Replacements ..............304 Keyboard Key References.......................307...
Page 16 Xenon XP User Guide...
Page 17: Customer Support
Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain warranty or non-warranty service, return your product to Honeywell (postage paid) with a copy of the dated purchase record. To learn more, go to sps.honeywell.com...
Page 18 xviii Xenon XP User Guide...
Page 19: Chapter 1 - Get Started
Product specifications, dimensions, warranty, and customer support information are also included. Honeywell barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the barcodes in this guide.
Page 20: Connect The Device
Connect the Device Connect with USB A scanner or a cordless base can be connected to the USB port of a computer. 1. Connect the appropriate interface cable to the device first, then to the com- puter. Corded Xenon XP Scanner USB Connection: Note: The power supply must be ordered separately, if needed.
Page 21 CCB-H-010BT/CCB-H-010BT-BF Base USB Connection: 3. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a barcode from the Sample Symbols, beginning on page 309. The unit defaults to a USB PC Keyboard. Refer to page 18 for other USB terminal settings.
Page 22: Connect With Keyboard Wedge
Connect with Keyboard Wedge A scanner or cordless base can be connected between the keyboard and PC as a “keyboard wedge,” where the scanner provides data output that is similar to keyboard entries. The following is an example of a keyboard wedge connection: 1.
Page 23 CCB01-010BT/CCB01-010BT-BF Base Keyboard Wedge Connection: CCB-H-010BT/CCB-H-010BT-BF Base Keyboard Wedge Connection: 4. Turn the terminal/computer power back on. The scanner beeps. 5. Verify the scanner or cordless base operation by scanning a barcode from the Sample Symbols, beginning on page 309. The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard.
Page 24: Connect With Rs232 Serial Port
Connect with RS232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner or cordless base to work properly, you must have the correct cable for your type of terminal/computer. Corded Xenon XP Scanner RS232 Serial Port Connection: Note: The power supply must be ordered separately, if needed.
Page 25 Base vertically, see Mount a CCB-H-010BT/CCB-H-010BT-BF Charge Base page 10. CCB01-010BT/CCB01-010BT-BF Base RS232 Serial Port Connection: CCB-H-010BT/CCB-H-010BT-BF Base RS232 Serial Port Connection: 4. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port. 5.
Page 26: Connect With Rs485
Connect with RS485 A Xenon scanner or cordless base can be connected for an IBM POS terminal interface. 1. Connect the appropriate interface cable to the device, then to the computer. Corded Xenon XP Scanner RS485 Connection: Note: The power supply must be ordered separately, if needed. 2.
Page 27 CCB01-010BT/CCB01-010BT-BF Base RS485 Connection: CCB-H-010BT/CCB-H-010BT-BF Base RS485 Connection: 3. Turn the terminal/computer power back on. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a barcode from the Sample Symbols, beginning on page 309. The scanner beeps once. For further RS485 settings, refer to RS485, page 16.
Page 28: Mount A Ccb01-010Bt/Ccb01-010Bt-Bf Charge Base
Mount a CCB01-010BT/CCB01-010BT-BF Charge Base 2.36 in. 2.8 in. 59.84mm 72.1mm 3.35 in. 8x32 thread 85.09mm x .39 in. (10mm) deep Mount a CCB-H-010BT/CCB-H-010BT-BF Charge Base The CCB-H-010BT/CCB-H-010BT-BF Base can be mounted on either a horizontal or vertical surface. Route the cables through the top, bottom, or sides of the base and secure the cables in the wireways.
Page 29: Horizontal Mount
Unlocked position for Locked position for horizontal mount vertical mount Use 30mm screws, appropriate for the mounting surface material, to mount the base securely. Horizontal Mount ") 43.97mm (1.73 ") 72.97mm (2.87 ") 85.1mm (3.35 ") 72.37mm (2.85 ") 43.97mm (1.73 Xenon XP User Guide...
Page 30: Vertical Mount
Vertical Mount 33.97mm 38.92mm ") ") (1.34 (1.53 15.07mm ") (0.59 ") 15.17mm (0.59 ") 100mm (3.94 ") 115.27mm (4.54 Reading Techniques The Xenon XP scanners have a view finder that projects a bright red aiming beam that corresponds to the scanner’s horizontal field of view. The aiming beam should be centered over the barcode, but it can be positioned in any direction for a good read.
Page 31: Menu Barcode Security Settings
Menu Barcode Security Settings Honeywell scanners are programmed by scanning menu barcodes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Barcode Security settings. Contact the nearest...
Page 32 custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings. Activate Custom Defaults Note: If using a cordless system, scanning this barcode also causes both the scanner and the base or Access Point to perform a reset and become unlinked.
Page 33: Chapter 2 - Program The Interface
CHAPTER PROGRAM THE INTERFACE Introduction This chapter describes how to program your system for the desired interface. Program the Interface - Plug and Play Plug and Play barcodes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
Page 34: Laptop Direct Connect
Laptop Direct Connect For most laptops, scanning the Laptop Direct Connect barcode allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect barcode also programs a carriage return (CR) suffix and turns on Emulate External Keyboard (page 31).
Page 35: Usb Ibm Surepos
IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface Each barcode above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 * 00 0A 0B...
Page 36: Usb Pc Or Macintosh Keyboard
No extra configuration (e.g., baud rate) is necessary. Note: If you scan the USB Serial barcode either with an older Honeywell serial driver, or no driver installed, you may no longer be able to scan barcodes. If this happens, either uninstall the older driver versions and install the latest driver, or delete the specific device entry in Device Manager.
Page 37: Cts/Rts Emulation
CTS/RTS Emulation CTS/RTS Emulation On * CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off ® Verifone Ruby Terminal Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This barcode sets the baud rate to 1200 bps and the data format to 8 data bits, mark parity bit, 1 stop bit.
Page 38: Gilbarco ® Terminal
Gilbarco Settings Honeywell Bioptic Aux Port Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This barcode sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Page 39: Wincor Nixdorf Terminal
Wincor Nixdorf Terminal Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Wincor Nixdorf Terminal Settings Wincor Nixdorf Beetle™...
Page 40: Wincor Nixdorf Rs232 Mode A
Wincor Nixdorf RS232 Mode A Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf RS232 Mode A terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, odd parity, 1 stop bit. The following prefixes are programmed for each symbology: Symbology Prefix...
Page 41 Keyboard Countries (Continued) Belarus Belgium Bosnia Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Xenon XP User Guide...
Page 42 Keyboard Countries (Continued) Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) Estonia Faroese Finland France Gaelic Germany Greek Xenon XP User Guide...
Page 43 Keyboard Countries (Continued) Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Xenon XP User Guide...
Page 44 Keyboard Countries (Continued) Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Xenon XP User Guide...
Page 45 Keyboard Countries (Continued) Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) Serbia (Cyrillic) Xenon XP User Guide...
Page 46 Keyboard Countries (Continued) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar Turkey F Xenon XP User Guide...
Page 47: Keyboard Wedge Modifiers
Keyboard Countries (Continued) Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United States (Dvorak right) United States (International) Uzbek (Cyrillic) Keyboard Wedge Modifiers ALT Mode If your barcode contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode.
Page 48: Keyboard Style
If your keystrokes require the ALT key and 3 or 4 characters, scan the 3 Characters or 4 Characters barcode. The data is then output with the special character(s) for values 00-255. Default = Off. * Off 3 Characters 4 Characters Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock.
Page 49: Keyboard Conversion
Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off. This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).
Page 50: Control Character Output
Convert All Characters to Upper Case Convert All Characters to Lower Case Control Character Output This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D.
Page 51 Default = Control + X Mode Off. Windows Mode Control + X Mode On * Control + X Mode Off DOS Mode Control + X Mode On Windows Mode Prefix/Suffix DOS Mode Control + X Mode On with Windows Mode Prefix/Suffix Supports ALT 3 Digit HEX Mode Turbo Mode: The scanner sends characters to a terminal faster.
Page 52: Rs232 Modifiers
Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off. Automatic Direct Connect Mode On * Automatic Direct Connect Mode Off RS232 Modifiers RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate.
Page 53: Rs232 Word Length: Data Bits, Stop Bits, And Parity
19200 38400 57,600 * 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.
Page 54: Rs232 Receiver Time-Out
7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual or serial trigger resets the time-out.
Page 55: Rs232 Timeout
Flow Control with Timeout: The scanner asserts RTS when it has data to send and waits for a delay (see RS232 Timeout on page 37) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the device transmit buffer is cleared and scanning may resume.
Page 56: Ack/Nak
* ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.
Page 57: Scanner-Bioptic Ack/Nak Mode
Scanner-Bioptic ACK/NAK Mode Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response. Default = Bioptic ACK/NAK Off.
Page 58 Xenon XP User Guide...
Page 59: Chapter 3 - Cordless System Operation
CHAPTER CORDLESS SYSTEM OPERATION How the Cordless Charge Base/Access Point Works A CCB01-010BT/CCB01-010BT-BF or a CCB-H-010BT/CCB-H-010BT-BF cordless charge base or an Access Point provides the link between the cordless scanner and the host system. The base/Access Point contains an interface assembly and an RF communication module.
Page 60: Link The Scanner To An Access Point
Link the Scanner to an Access Point Note: Linking to an Access Point is only supported by Xenon XP 1952 models. Turn on the computer (laptop/desktop). Plug the interface cable into the Access Point first and then into the Page Button appropriate port on the computer.
Page 61: Program The Scanner And Base Or Access Point
When data is scanned, the data is sent to the host system via the base or Access Point. The cordless scanner recognizes data acknowledgment (ACK) from the base or Access Point. If it cannot be determined that the data has been properly sent to the base or Access Point, the scanner issues an error indication.
Page 62: System Conditions
of 328 feet (100m) or 33 feet (10m) between the scanner and base or Access Point, depending on the environment. See Flexible Power Management, page 61, for information about controlling this range. System Conditions The components of the cordless system interact in specific ways as you associate a scanner to a base or Access Point, as you move a scanner out of range, bring a scanner back in range, or swap scanners between two cordless systems.
Page 63: Page Button
Page Button When you press the page button on the base or Access Point, the scanners associated with that base or Access Point will begin beeping (3 short and 1 long beep). If you press the trigger on a scanner that is beeping in response, or press the page button on the base or Access Point a second time, all associated scanners will stop beeping.
Page 64: Temporary Streaming Presentation Timeout
When the scanner is out of the base, the page button works normally. Default = Temporary Streaming Presentation Mode On. * Temporary Streaming Presentation Mode To remove Temporary Streaming Presentation Mode, scan the barcode for Page Mode On page Temporary Streaming Presentation Timeout Set a timeout for the length of time the illumination remains on and searching for barcodes when using Temporary Streaming Presentation Mode.
Page 65: Battery Information For The Xenon Xp 1952G/1952H
Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page xvii for additional information.
Page 66: Instant Charge Pack Information For The Xenon Xp 1952G-Bf/Xenon Xp 1952H-Bf
Caution: A Xenon XP 1952-BF scanner can only be charged by CCB01- 010BT-BF or CCB-H-010BT-BF base. Use of any non- Honeywell power supply may result in damage not covered by the warranty. Power is supplied to the cordless scanner by a rechargeable instant charge pack that is integrated in the scanner handle.
Page 67: Scanner Charge Pack Status
Scanner Charge Pack Status The following charge status feedback is provided by the scanner when the scanner is out of the base and has been idle for 5 seconds. Scanner LED Scanner Beep Charge Level Yellow, 3 sets of flashes No beep less than 15% repeated every 3 seconds...
Page 68: Base Power Communication Indicator
Base Power Communication Indicator To display the power indicator on a base or an Access Point, scan the Base Power Communication Indicator On barcode. To turn off the power indicator, scan the Off barcode. Default = On. * Base Power Communication Indicator On Base Power Communication Indicator Off...
Page 69: Low Power Alert Range
Low Power Alert Range Set the power range that will trigger a low power alert. Default = 10-30%. *Low Power Alert 10-30% Low Power Alert 10-50% Low Power Alert Flash Number You can program the battery-free scanner’s LEDs to flash up to 9 times for the low power alert.
Page 70: Low Power Alert Beep
Interval Between Alerts If you have set the Low Power Alert Repeat (page 51) to more than 1, you can set the length of time, in seconds, between the low power alerts. To set this interval, scan the barcode below and then scan a digit (10-120) barcode from the Programming Chart, beginning on page 311, then Save.
Page 71: Base Charge Modes
to shut down when in the base cradle, scan Shut Down Scanner in Cradle. Default for CCB01-010BT = Scan in Cradle On. Default for CCB-H-010BT = Scan in Cradle Off. Scan in Cradle Off Scan in Cradle On Shut Down Scanner in Cradle Base Charge Modes When the base has both an external power supply (plugged into the auxiliary power port) and a host interface cable, it will draw its power from the external power...
Page 72: Page Mode
* External or Interface Cable Power External Power Only Page Page Mode By default, the page button on the base or Access Point pages the scanners associated with that base or Access Point. If you want the page button on your base or Access Point to be disabled, scan the Page Mode Off barcode, below.
Page 73: Error Indicators
Medium (3250 Hz) High (4200 Hz) Error Indicators Beeper Pitch - Base Error The base can be configured to beep at a particular pitch when an error occurs, such as transmission problems to a host system. The beeper pitch codes modify the pitch (frequency) of the error tone the base emits when there is an error.
Page 74: Scanner Report
Scanner Report Scan the barcode below to generate a report for the connected scanners. The report indicates the port, work group, scanner name, and address. To assign a name to your scanner, refer to Menu Command Syntax, page 239. Scanner Report Scanner Address Scan the barcode below to determine the address of the scanner you are using.
Page 75: Charge And Link Mode
In order to program the base for Charge Only Mode, you must link a scanner to it. Once the scanner is linked to the base, scan the Charge Only Mode barcode. Any subsequent scanners placed in that base will charge without linking to it. The scanner used to program the base remains linked to the base.
Page 76: Unlink The Scanner
Open Link Mode - Single Scanner When newly shipped or defaulted to factory settings, a scanner is not linked to a base or an Access Point. A link is established when the scanner is placed into a base, or an Access Point linking barcode is scanned. When in Open Link Mode, a new link is established when a new scanner is placed in the base, or you scan an Access Point linking barcode.
Page 77: Alarm Sound Type
base and to set the alarm duration, scan the appropriate barcode below and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart, beginning on page 311, then Save. Default = 0 sec (no alarm). Base Alarm Duration Note: The Access Point does not have a base alarm.
Page 78: Scanner Power Time-Out Timer
Scanner Power Time-Out Timer When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner power time-out barcode to change the time-out duration (in seconds). Note: Scanning zero (0) is the equivalent of setting no time-out. If there are no trigger pulls during the timer interval, the scanner goes into power down mode.
Page 79: Flexible Power Management
Flexible Power Management If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn down the power output of the scanner. This reduces the range between the scanner and a base or an Access Point as shown in the following illustration: Scanner 802.11...
Page 80: Xenon Xp 1952G-Bf/1952H-Bf
Access Point once the scanner is back in range or when the records are manually transmitted. Note: Batch Mode is only supported by the Honeywell Charge and Communication Base (CCB) and Honeywell Access Point (AP). Batch mode has limitations when using multiple scanners to one base or Access Point.
Page 81: Batch Mode Beep
the scanner’s buffer space is full, any barcodes scanned generate an error tone. In order to scan barcodes again, the data must be transmitted to the base or Access Point. Once the data is transmitted, it is cleared in the scanner. Persistent Batch Mode is the same as Inventory Batch Mode, except that once the data is transmitted to the base or Access Point, it is retained in the scanner.
Page 82: Batch Mode Quantity
Flash Storage: The scanner writes any untransmitted data to flash memory prior to powering down. The data will still be there when the scanner powers back up. However, the scanner will power down, even with untransmitted data, if it reaches a power down timeout or if the battery or charge pack power is very low.
Page 83 For example, if the Quantity 5 barcode is scanned after the quantity has been set to 1234, then the 1 is dropped, the quantity will be 2345. Example: Add a quantity of 5 for the last item scanned. 1. Scan the item's barcode. 2.
Page 84: Batch Mode Output Order
Quantity Codes (Continued) Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO. * Batch Mode FIFO Batch Mode LIFO Total Records If you wish to output the total number of barcodes scanned when in Batch Mode, scan Total Records.
Page 85: Delete Last Code
Delete Last Code If you want to delete the last barcode scanned when in Batch Mode, scan Delete Last Code. Delete Last Code Clear All Codes If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes.
Page 86: Multiple Scanner Operation
Batch Mode Transmit Delay Medium (500 ms) Batch Mode Transmit Delay Long (1000 ms) Multiple Scanner Operation Note: Multiple Scanner Operation Mode allows you to link up to 3 scanners to one base or Access Point. You cannot join a 4th scanner until you unlink one of the 3 scanners or take a scanner out of range.
Page 87: Application Work Groups
You could assign all the scanners in the retail area to one work group and those in the warehouse to another. Consequently, any desired changes to either the retail or warehouse area would apply to all scanners in that particular work group. Honeywell’s online configuration tool, EZConfig-Scanning (page 236), makes it easy for you to program your system for use with multiple scanners and multiple work groups.
Page 88: Application Work Group Selection
The scanner keeps a copy of the menu settings it is using. Whenever the scanner is connected or reconnected to a base or an Access Point, the scanner is updated with the latest settings from the base or Access Point for its work group. The scanner also receives menu setting changes processed by the base or Access Point.
Page 89: Reset The Custom Defaults: All Application Work Groups
The scanner can be used either with the charge base, an Access Point, or with other Bluetooth devices. Those devices include personal computers, laptops, PDAs, and Honeywell mobility systems devices. Bluetooth Secure Simple Pairing (SSP) Secure Simple Pairing (SSP) allows you to connect simply and securely to other...
Page 90: Bluetooth Hid Keyboard Connect
version 2.1 or higher. When SSP is on, no PIN is required for pairing. Turn SSP off if you are connecting to a Bluetooth device that is not using a compatible Bluetooth version. Default = Bluetooth SSP On. * Bluetooth SSP On Bluetooth SSP Off Bluetooth HID Keyboard Connect Your scanner can be paired with Bluetooth-capable devices, such as personal...
Page 91 Save Xenon XP User Guide...
Page 92: Virtual Keyboard
Virtual Keyboard Once your scanner has been connected directly to an iPad, smart phone, or laptop, you can toggle the virtual keyboard on your device with a quick double pull of the scanner trigger. Bluetooth HID Keyboard Disconnect If your scanner has been connected directly to an iPad, smart phone, or laptop, you must disconnect it in order to once again communicate with the base or Access Point.
Page 93: Pdas/Mobility Systems Devices
PDAs/Mobility Systems Devices You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the barcode below and follow the instructions supplied with your Bluetooth device to locate the scanner, and connect with it. BT Connection - PDA/Mobility Systems Device Change the Scanner’s Bluetooth PIN Code...
Page 94: Maximum Link Attempts
The table below shows the results of the Auto Reconnect On and Off settings: Event Auto Reconnect On Auto Reconnect Off Scanner out of range Relink occurs automatically. If The scanner is relinked by maximum number of link attempts pulling the trigger, or scanning is unsuccessful, then the scanner the Access Point linking must be relinked by either pulling...
Page 95: Relink Time-Out
Relink Time-Out Relink Time-Out controls the idle time between relink attempts. An attempt to link a scanner to a base or an Access Point typically lasts up to 5 seconds. This is the time when the scanner is actually attempting a contact. Relink Time-Out controls the amount of time, in seconds, that elapses between the end of one connection attempt and the start of the next.
Page 96: Host Acknowledgment
saved in batch mode. After one hour, the scanner powers off and batch mode data is lost. Refer to Auto Reconnect Mode, page 75, to review other events that can start the relink process. Example: Auto Reconnect Mode set to 1 Maximum Link Attempts set to 0 Relink Time-Out set to 10 Scanner Power Time-Out Timer set to 1800...
Page 97: Host Ack On/Off
The commands to which the scanner responds are listed on page 80. The [ESC] is a 1B in hex. A typical command string is y [ESC] x, where “y” is the application work group number, “[ESC] x” is the escape command, and the comma is the terminator, which is required.
Page 98: Host Ack Timeout
Host ACK Timeout You can set a timeout for the length of time the scanner waits for a valid escape command when using Host Acknowledgment Mode. Set the length (in seconds) for a timeout by scanning the following barcode, then setting the timeout (from 1-90 seconds) by scanning digits from the Programming Chart, beginning on page 311,...
Page 99: Chapter 4 - Input/Output Settings
CHAPTER INPUT/OUTPUT SETTINGS Power Up Beeper The scanner can be programmed to beep when it’s powered up. If you are using a cordless system, the base can also be programmed to beep when it is powered up. Scan the Off barcode(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner.
Page 100: Beep On Bel Character
Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On barcode below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off. *Beep on BEL Off Beep on BEL On Trigger Click...
Page 101: Beeper Volume - Good Read
Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High for Xenon XP, Low for Xenon XP healthcare scanners. * Low Medium * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read.
Page 102: Vibrate - Good Read
Vibrate – Good Read The scanner vibrates once when a barcode is successfully read, and twice when a programming barcode is successfully read. When a programming barcode is unsuccessful, the scanner emits one long vibration (2 times the Vibrate Duration length).
Page 103: Beeper Duration - Good Read
Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
Page 104: Good Read Delay
to an error. To change the number of error beeps, scan the barcode below and then scan a digit (1-9) barcode from the Programming Chart, beginning on page 311, then Save. Default = 1. Number of Error Beeps/LED Flashes Good Read Delay This sets the minimum amount of time before the scanner can read another barcode.
Page 105: Trigger Modes
Trigger Modes Manual Trigger When in manual trigger mode, the scanner scans until a barcode is read, or until the trigger is released. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode.
Page 106 Trigger Number This sets the number of trigger presses required to activate the Trigger Toggle Mode. 2 Quick Triggers 3 Quick Triggers 4 Quick Triggers Trigger Timing This sets the timing of the trigger presses in order to qualify as a trigger toggle, rather than a regular trigger press.
Page 107: Serial Trigger
Serial Trigger You can activate the scanner either by pressing the trigger, or using a serial trigger command (see Trigger Commands on page 242). You must be in a serial interface mode in order to use serial triggering. Refer to RS232 Serial Port (page 16) or Serial...
Page 108: Triggered Presentation Mode
Triggered Presentation Mode This mode uses light to detect the presence of an object. Default = Ambient and Scanner Light. Ambient Light Only *Ambient and Scanner Light Presentation LED Behavior after Decode When a scanner is in presentation mode, the LED aimer dims 30 seconds after a barcode is decoded.
Page 109 Barcode 1 Barcode 2 90% 100% Note: A barcode needs only to be touched by the centering window in order to be read. It does not need to pass completely through the centering window. Scan Presentation Centering On, then scan one of the following barcodes to change the top, bottom, left, or right of the centering window.
Page 110: In-Stand Sensor Mode
Left of Presentation Centering Window Right of Presentation Centering Window In-Stand Sensor Mode Note: The In-Stand Sensor feature only applies to Xenon XP 1950g, 1950h, 1952g, and 1952h products. It does not apply to the Xenon XP 1952-BF products. This feature senses when the scanner is removed from the stand and tells it to begin manual triggering.
Page 111: Poor Quality Pdf Codes
* Poor Quality 1D Reading Off Poor Quality PDF Codes This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. It is useful when a complete barcode cannot be seen in one image. This setting does not affect 1D barcode reading.
Page 112: Codegate
CodeGate™ When CodeGate is On, the trigger is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding barcodes, but the barcode data is not transmitted until the trigger is pressed. When CodeGate is Off, barcode data is transmitted when it is decoded.
Page 113: Streaming Presentation In-Stand
Streaming Presentation In-Stand This option is available when using In-Stand Sensor Mode, page 92. You may program a specific Streaming Presentation Mode for in-stand scanning, and a Manual Trigger mode for out-of-stand scanning. To do this, you must first scan the preferred Streaming Presentation mode (Normal or Enhanced), then scan the Manual Trigger mode (Normal or Enhanced) you want to use.
Page 114: User-Specified Reread Delay
Extra Long (2000 ms) User-Specified Reread Delay If you want to set your own length for the reread delay, scan the barcode below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 311, then Save. User-Specified Reread Delay 2D Reread Delay Sometimes 2D barcodes can take longer to read than other barcodes.
Page 115: Character Activation
Character Activation You may use a character sent from the host to trigger the scanner to begin scanning. When the activation character is received, the scanner continues scanning until either the Character Activation Timeout (page 98) is reached, the deactivation character is received (see Deactivation Character on page 98), or a barcode is transmitted.
Page 116: Character Activation Timeout
End Character Activation After Good Read Character Activation Timeout You can set a timeout for the length of time the illumination remains on and attempting to decode barcodes when using Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following barcode, then setting the timeout (from 1-300,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 311, then Save.
Page 117: Illumination Lights
Illumination Lights If you want the illumination lights on while reading a barcode, scan the Lights On barcode, below. However, if you want to turn just the lights off, scan the Lights Off barcode. Default = Lights On. Note: This setting does not affect the aimer light. The aiming light can be set using Aimer Mode (page 100).
Page 118: User-Specified Aimer Delay
User-Specified Aimer Delay If you want to set your own length for the duration of the delay, scan the barcode below, then set the time-out by scanning digits (0 - 4,000 ms) from the Programming Chart, beginning on page 311, then Save. Delay Duration Aimer Mode This feature allows you to turn the aimer on and off.
Page 119: Single Code Centering
Single Code Centering Scan Single Code Centering to target the barcode closest to the center of the image. Singling out a barcode in this manner increases scanning accuracy when there are multiple barcodes close together. Single Code Centering Custom Centering Use the following settings to customize your centering window.
Page 120: Preferred Symbology
does not need to pass completely through the centering window. Scan Centering On, then scan one of the following barcodes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits from the Programming Chart, beginning on page 311, then Save.
Page 121: High Priority Symbology
If the time-out period expires before a high priority symbology is read, the scanner will read any barcode in its view (low priority or unspecified). If there is no barcode in the scanner’s view after the time-out period expires, then no data is reported. Note: A low priority symbol must be centered on the aiming pattern to be read.
Page 122: Preferred Symbology Time-Out
Preferred Symbology Time-out Once you have enabled Preferred Symbology and entered the high and low priority symbologies, you must set the time-out period. This is the period of time the scanner will search for a high priority barcode after a low priority barcode has been encountered.
Page 123: Output Sequence Editor Commands
1. If you are using barcodes to create your output sequence, scan Enter Output Sequence on page 108. 2. Code I.D. On the Symbology Charts on page 297, find the symbology to which you want to apply the output sequence format. Make a note of the hex value for that symbology.
Page 124 SEQISU Add suffix to partial output sequences. SEQISE Add separators to partial output sequences. TRGSTO Timeout for partial output sequences. Termination string. SEQ_EN1 Require output sequence on/not required. SEQ_EN2 Require output sequence required. BEPSIN0 Good read beep - each code in sequence. BEPSIN1 Good read click - each code in sequence.
Page 125 9999 code length that must match for PDF417, 9999 = all lengths start character match for PDF417, 4Dh = “M” termination string for third code The whole command line would look like this: SEQBLK62999943FF6A999954FF7299994DFF. SEQDFT;SEQ_EN1;SEQBLK62999943FF6A999954FF7299994DFF. The data is output as: CODE39SMPLTSTMSGCODE128MSGPDF417 Output Sequence Example 2 - Three Symbologies with <>...
Page 126: Enter Output Sequence
termination string for first code code identifier for PDF417 9999 code length that must match for PDF417, 9999 = all lengths start character match for PDF417, 4Dh = “M” termination string for third code But you would add your <> separators for each sequence: SEQSEP99 separator for each sequence, 99 = all symbologies left bracket (<)
Page 127: Partial Sequence
Partial Sequence If an output sequence operation is terminated before all your output sequence criteria are met, the barcode data acquired to that point is a “partial sequence.” You can define how partial sequences are output using the same types of command strings you used to create output sequences.
Page 128 But you would add your <> separators for each sequence: SEQISE99 separator for each sequence, 99 = all symbologies left bracket (<) right bracket (>) And add the carriage return and line feed as a suffix: SEQISU99 separator for suffixes, 99 = all symbologies carriage return line feed And you would add >PARTIAL<...
Page 129 Discard Partial Output Sequence If you want to discard partial sequences when the output sequence operation is terminated before completion, scan Discard Partial Sequence. * Discard Partial Sequence Output Sequence Timeouts You can set a timeout for every code in the output sequence defined by the SEQBLK command.
Page 130 Satisfactory Subset of Full Sequence Timeout Example To specify a subset, list its members using the SEQSAT command and terminate each subset with FF. The members of each subset are specified as single hex digits corresponding to their index within the full sequence, 1 being the first. For example, to specify two subsets, the first consisting of the first and second code in the sequence and the second subset consisting of the second and third code, use the command SEQSAT12FF23FF.
Page 131 1. First scan Code 39. Output CODE39SMPL 2. First scan Code 128, and then scan Code 39 and wait for timeout. Output CODE39SMPLTSTMSGCODE128 3. First scan PDF417, and then scan Code 39 and wait for timeout. Output CODE39SMPLMSGPDF417 4. First scan Code 128, and then scan PDF417. Output TSTMSGCODE128MSGPDF417 5.
Page 132: Good Read Tone - Output Sequences
Good Read Tone - Output Sequences The scanner may be programmed to either beep or click in response to a good read of each barcode in an output sequence, or to emit a beep or error tone for a partial sequence.
Page 133: No Read
No Read With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data Window (see page 237), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear. Default = Off.
Page 134: Working Orientation
* Video Reverse Off Working Orientation Some barcodes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner.
Page 135: Chapter 5 - Healthcare Settings
CHAPTER HEALTHCARE SETTINGS The following settings have been developed to enhance scanning in a healthcare environment. These settings are only supported by the Xenon XP 1950h scanner and the Xenon XP 1952h and Xenon XP 1952h-BF scanner and base. They allow you to set quickly configure streaming presentation, and to set the scanner and base to quiet modes for scanning that do not disturb resting patients.
Page 136: Silent Mode With Long Led
Silent Mode with Long LED Scan the following barcode to completely silence the scanner and base. The scanner beep, base beep, base and scanner power up beep, and scanner linking sounds are all silenced. When a barcode is scanned, the LED and aimer remain solidly lit for 1 second.
Page 137: Low Beeper (Daytime Mode)
Low Beeper (Daytime Mode) The following barcode sets all sounds to on, but at a low volume. The scanner beep, base beep, base and scanner power up beep, and scanner linking sounds are all set to low volume. Daytime Mode - Cordless Scanner and Base Daytime Mode - Corded Scanner...
Page 138: Number Of Led Flashes
Number of LED Flashes If you have silenced the scanner’s beeper, you may set the number of times the LED flashes when reading barcodes. Default = 1 LED Flash. Note: If you have set LED Solid (No Flash) (page 121), to anything but Off, that setting will override the LED Flash settings.
Page 139: Led Solid (No Flash)
LED Solid (No Flash) Under normal operations, the scanner’s LED flashes once for a good read. You may set the LED to remain on for a length of time after a good read instead of flashing. Default = LED Solid Off (Resume Flash). * LED Solid Off (Resume Flash) LED Solid 1 Second...
Page 140: Out-Of-Range Alarm Volume
Page Volume Medium Page Volume High Out-of-Range Alarm Volume Note: This setting is not supported by the Xenon XP 1950h scanner. If your scanner is out range of the base, an alarm sounds from both your base and scanner. If your scanner is out range of an Access Point, an alarm sounds from just the scanner.
Page 141: Out-Of-Range Delay
Scanner Alarm Volume Medium Base Alarm Volume High Scanner Alarm Volume High Out-of-Range Delay Note: This setting is not supported by the Xenon XP 1950h scanner. When using the Out-of-Range Alarm settings, the length of the delay for the alarm is set with an Out-of-Range Delay.
Page 142 Xenon XP User Guide...
Page 143: Chapter 6 - Data Edit
CHAPTER DATA EDIT Prefix/Suffix Overview When a barcode is scanned, additional information is sent to the host computer along with the barcode data. This group of barcode data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.
Page 144: Add A Prefix Or Suffix
• Enter prefixes and suffixes in the order in which you want them to appear on the output. • When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character. •...
Page 145: Add A Carriage Return Suffix To All Symbologies
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit hex value from the Symbology Chart (included in Symbology Charts, beginning on page 297) for the symbology from which you want to clear the prefix or suffix. Step 3.
Page 146: Function Code Transmit
Clear All Suffixes Function Code Transmit By default, all ASCII control characters are transmitted with barcode data. These non-printable characters are translated into predefined key strokes, or CTRL+X functions (see ASCII Conversion Chart (Code Page 1252), beginning on page 300). If these key strokes interfere with your host’s software application, scan Disable to keep these ASCII control characters from being transmitted.
Page 147: User Specified Intercharacter Delay
To remove this delay, scan the Intercharacter Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 311. Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data.
Page 148: Intermessage Delay
To remove this delay, scan the Interfunction Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 311. Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.
Page 149: Chapter 7 - Data Format
CHAPTER DATA FORMAT Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in barcode data as it is scanned. The selections in the following pages are used only if you wish to alter the output.
Page 150: Show Data Format
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data Format code below. * Default Data Format Show Data Format Scan the barcode below to show current data format settings. Data Format Settings Add a Data Format Step 1.
Page 151: Other Programming Selections
Chart, beginning on page 311. For example, 50 characters is entered as 0050. Note: 9999 indicates all lengths. Step 6. Editor Commands Refer to Data Format Editor Commands (page 134). Scan the symbols that represent the command you want to enter. Step 7.
Page 152: Terminal Id Table
Save Discard Terminal ID Table Terminal Model(s) Terminal ID PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop Serial RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) Keyboard PS2 compatibles AT compatibles Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your...
Page 153 Send a number of characters F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor position and continue for “nn” characters or through the last character in the input message, followed by character “xx.” Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the insert character’s hex value for its ASCII code.
Page 154 Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss”...
Page 155 42 is the hex value for B The data is output as: 1234567890 Send all but the last characters E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included.
Page 156 1234567890**ABCDEFGHIJ Insert symbology name B3 Insert the name of the barcode’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page 297). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 300 for decimal, hex and character codes.
Page 157 B3 is the “Insert symbology name” command F4 is the “Insert a character multiple times” command 20 is the hex value for a space 01 is the number of times the space character is sent B4 is the “Insert barcode length” command F4 is the “Insert a character multiple times”...
Page 158: Move Commands
If there are three keystrokes, the syntax would change from B5xxssnn for one keystroke to B5xxssnnssnnssnn. An example that would insert "abc" is as follows: B503001F00320030F833. Note: Key modifiers can be added together when needed. The sum is converted to hexadecimals.
Page 159: Search Commands
FE and F7 Example: Manipulate barcodes that begin with a 1 Search for barcodes that begin with a 1. If a barcode matches, move the cursor back to the beginning of the data and send 6 characters followed by a carriage return.
Page 160 F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: DEFGHIJ Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx”...
Page 161 Search backward for a string B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B1nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B1000454657374 will search backward for the first occurrence of the 4 character string “Test.”...
Page 162: Miscellaneous Commands
Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command.
Page 163 If the barcode has characters that the host application does not want included, you can use the E4 command to replace those characters with something else. In this example, you will replace the zeros in the barcode above with carriage returns. Command string: E402300DF10D E4 is the “Replace characters”...
Page 164 EC Example: Only output the data if the barcode begins with a number If you want only data from barcodes that begin with a number, you can use EC to check for the number. Command string: ECF10D EC is the “Check for a number” command F1 is the “Send all characters”...
Page 165: Data Formatter
Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation. Discard Data B8 Discards types of data.
Page 166: Data Format Non-Match Error Tone
requirements generates an error tone and the data in that barcode is not transmitted. If you wish to process this type of barcode without generating an error tone, see Data Format Non-Match Error Tone. • Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format.
Page 167: Primary/Alternate Data Formats
Data Format Non-Match Error Tone Off Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the barcodes below.
Page 168 Single Scan-Data Format 1 Single Scan-Data Format 2 Single Scan-Data Format 3 Xenon XP User Guide...
Page 169: Chapter 8 - Symbologies
CHAPTER SYMBOLOGIES This programming section contains the following menu selections. Refer to Chapter 11 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) •...
Page 170: All Symbologies
All Symbologies For best scanner performance, you should only enable the symbologies that you need. Scan All Symbologies Off to disable all symbologies, then enable the symbologies you need by scanning the On barcode for each symbology. All Symbologies Off Message Length Description You are able to set the valid reading length of some of the barcode symbologies.
Page 171 Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar barcodes with Modulo 16 check characters.
Page 172 Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omitted. A 1 2 3 4 D D 5 6 7 8 A Select Require to prevent the scanner from decoding a single “D”...
Page 173: Code 39
Code 39 < Default All Code 39 Settings > Code 39 On/Off * On If you are reading Code 39 barcodes, Codablock A should remain disabled. If you are enabling Codablock A (see Codablock A on page 191), you should disable Code Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the barcode.
Page 174 When Check Character is set to Validate and Transmit, the scanner only reads Code 39 barcodes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Code 39 Message Length...
Page 175 Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as PARAF. Note: Trioptic Code (page 191) must be turned off while scanning Code 32 Pharmaceutical codes.
Page 176: Interleaved 2 Of 5
* Full ASCII Off Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting.
Page 177 When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 barcodes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...
Page 178: Nec 2 Of 5
NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits barcode data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 barcodes printed with a check digit, but will not transmit the check digit with the scanned data.
Page 179: Code 93
NEC 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 <...
Page 180 Code 93 Append This function allows the scanner to append the data from several Code 93 barcodes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 93 barcodes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data.
Page 181: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)
Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information.
Page 182: Straight 2 Of 5 Iata (Two-Bar Start/Stop)
Straight 2 of 5 IATA (two-bar start/stop) Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA barcodes, you may want to adjust the redundancy count.
Page 183: Matrix 2 Of 5
Maximum Message Length Matrix 2 of 5 Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information.
Page 184: Code 11
Code 11 Code 11 On/Off * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 barcodes. Default = Two Check Digits. One Check Digit * Two Check Digits Code 11 Message Length Scan the barcodes below to change the message length.
Page 185: Code 128
Code 128 Code 128 On/Off * On If you are reading Code 128 barcodes, Codablock F should remain disabled. If you are enabling Codablock F (see Codablock F on page 192), you should disable Code 128.
Page 186 the higher the redundancy count, the longer it will take to decode the barcode. To adjust the redundancy, scan the Code 128 Redundancy barcode below, then scan a redundancy count between 0 and 10 on the Programming Chart, beginning on page 311.
Page 187: Gs1-128
Character Replacements on page 304), and scan the value and the Save barcode from the Programming Chart, beginning on page 311. The data characters should then appear properly. Code 128 Code Page GS1-128 GS1-128 On/Off * On GS1-128 Message Length Scan the barcodes below to change the message length.
Page 188: Telepen
Telepen Telepen On/Off * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2).
Page 189: Upc-A
Maximum Message Length UPC-A UPC-A On/Off * On Note: To convert UPC-A barcodes to EAN-13, see Convert UPC-A to EAN-13 on page 178. UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Page 190 UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but can be programmed so it is not transmitted (Off). Default = On. * On UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 191: Upc-A/Ean-13 With Extended Coupon Code
* Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A Addenda Required.
Page 192: Coupon Gs1 Databar Output
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off. * Off Allow Concatenation Require Concatenation...
Page 193: Upc-E0
UPC-E0 UPC-E0 On/Off Most U.P.C. barcodes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use UPC-E1 (page 177).
Page 194 Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required.
Page 195: Upc-E1
UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = On. * On UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 196: Ean/Jan-13
* UPC-E1 Off EAN/JAN-13 EAN/JAN-13 On/Off * On Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A barcodes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
Page 197 EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 198 EAN-13 Beginning with 290 Addenda Required This setting programs the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with “290.” The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 barcodes that begin with “290” must have a 5 digit addendum.
Page 199 Default = Don’t Require Addenda. * Don’t Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 414/419 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a “414”...
Page 200 Require 2 or 5 Digit Addenda EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a “434” or “439.” The following settings can be programmed: Require Addenda: All EAN-13 barcodes that begin with a “434”...
Page 201 Don’t Require 2 Digit Addenda: If you have selected Require 2 Digit Addenda, and you want to disable this feature, scan Don’t Require 2 Digit Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required.
Page 202 Don’t Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don’t Require 5 Digit Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required.
Page 203: Isbn Translate
ISBN Translate When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off. * Off EAN/JAN-8 EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether or not the check digit should be transmitted at the end of the scanned data.
Page 204 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 barcodes that...
Page 205: Msi
setting the timeout (from 0-500 milliseconds) by scanning digits from the Programming Chart, beginning on page 311 of this manual, then Save. Default = 120. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the barcode and the data from the addenda.
Page 206 MSI Check Character Different types of check characters are used with MSI barcodes. You can program the scanner to read MSI barcodes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI barcodes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
Page 207: Gs1 Databar Omnidirectional
MSI Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length GS1 DataBar Omnidirectional <...
Page 208: Gs1 Databar Limited
GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information.
Page 209: Trioptic Code
Maximum Message Length Trioptic Code Note: If you are going to scan Code 32 Pharmaceutical codes (page 157), Trioptic Code must be off. Trioptic Code is used for labeling magnetic storage media. * Off Codablock A Codablock A On/Off * Off If you are reading Code 39 barcodes, Codablock A should remain disabled.
Page 210: Codablock F
Codablock A Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600. Minimum Message Length Maximum Message Length Codablock F ...
Page 211: Label Code
Maximum Message Length Label Code The standard Label Code is used in libraries. Default = Off. *Off PDF417 < Default All PDF417 Settings > PDF417 On/Off * On Xenon XP User Guide...
Page 212: Macropdf417
PDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750. Minimum Message Length Maximum Message Length MacroPDF417 MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 barcodes.
Page 213: Gs1 Composite Codes
* Off MicroPDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366. Minimum Message Length Maximum Message Length GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new...
Page 214: Gs1 Emulation
UPC/EAN Version Scan the UPC/EAN Version On barcode to decode GS1 Composite symbols that have a U.P.C. or an EAN linear component. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Version Off. UPC/EAN Version On * UPC/EAN Version Off Note: If you scan coupons that have both UPC and GS1 Databar codes, you may wish to...
Page 215: Tcif Linked Code 39 (Tlc39)
If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPC- E expansion is controlled by the UPC-E0 Expand (page 175) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts page 297).
Page 216: Qr Code
QR Code < Default All QR Code Settings > QR Code On/Off This selection applies to both QR Code and Micro QR Code. * On QR Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information.
Page 217 Swipe: Pull and hold down the trigger and scan all appended QR Codes while keeping the trigger pressed. The scanner emits short beeps for each partial QR Code that is scanned and buffered. One long beep is emitted after the last QR Code is scanned and the data is complete.
Page 218: Dotcode
DotCode < Default All DotCode Settings > DotCode On/Off * Off Poor Quality DotCodes This setting improves the scanner’s ability to read damaged or badly printed DotCodes. Default = Poor Quality DotCodes Off. Poor Quality DotCodes On * Poor Quality DotCodes Off DotCode Message Length Scan the barcodes below to change the message length.
Page 219: Digimarc Barcode
Digimarc Barcode™ Digimarc Decoder Attempts Set the number of attempts by scanning the barcode below, then setting the number of attempts (0-10) by scanning digits from the Programming Chart beginning on page 311 of this manual, the Save. Minimum to Maximum attempts = 0-10.
Page 220: Data Matrix
* Uses Digimarc Decoder then Both Decoders Uses ID Decoder then Alternates Decoders Uses Digimarc Decoder then Alternates Decoders Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Direct Part Marking Decoding If you are having trouble reading Direct Part Marking (DPM) barcodes, scan Dotpeen DPM Decoding for Dotpeen codes or scan Reflective (Etched) DPM Decoding for reflective (etched) codes Default = Disable DPM Decoding.
Page 221 * Disable DPM Decoding Reflective (Etched) DPM Decoding Data Matrix Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116. Minimum Message Length Maximum Message Length Data Matrix Code Page...
Page 222: Maxicode
MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off * Off MaxiCode Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150. Minimum Message Length Maximum Message Length Xenon XP User Guide...
Page 223: Aztec Code
Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Aztec Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 1-3832.
Page 224: Chinese Sensible (Han Xin) Code
Aztec Code Page Aztec Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting.
Page 225: Postal Codes - 2D
Han Xin Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833. Minimum Message Length Maximum Message Length Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations...
Page 226 Japanese Post On KIX Post On Planet Code On Also see Planet Code Check Digit, page 210. Postal-4i On Postnet On Postnet On Also see Postnet Check Digit, page 211. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British Post On Intelligent Mail Barcode and...
Page 227 Postnet and Postal-4i On Postnet and Intelligent Mail Barcode On Postal-4i and Intelligent Mail Barcode On Postal-4i and Postnet with B and B’ Fields On Planet Code and Postnet On Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and...
Page 228: Planet Code Check Digit
Planet Code, Postal-4i, and Intelligent Mail Barcode On Postnet, Postal-4i, and Intelligent Mail Barcode On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intelligent Mail Barcode, and Postnet with B and B’ Fields On Postal-4i, Intelligent Mail Barcode, and Postnet with B and B’...
Page 229: Postnet Check Digit
* Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Australian Post Interpretation This option controls what interpretation is applied to customer fields in Australian 4-State symbols.
Page 230: Postal Codes - Linear
Combination C and N Tables Postal Codes - Linear The following lists linear postal codes. Any combination of linear postal code selections can be active at a time. China Post (Hong Kong 2 of 5) China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Message Length...
Page 231: Korea Post
Korea Post Korea Post * Off Korea Post Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 152) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Korea Post Check Digit...
Page 232 Xenon XP User Guide...
Page 233: Chapter 9 - Imaging Commands
CHAPTER IMAGING COMMANDS The scanner is like a digital camera in the way it captures, manipulates, and transfers images. The following commands allow you to alter the way the scanner performs these functions. Note: If you are using the scanner in a stand, you must set the In-Stand Sensor Mode to Off in order to take images (see In-Stand Sensor Mode on page 92).
Page 234: Image Snap - Imgsnp
Image Ship - IMGSHP (page 219) Intelligent Signature Capture - IMGBOX (page 228) The modifiers for each of these commands follow the command description. Note: The images included with each command description are examples only. The results you achieve may be different from those included in this manual. The quality of the output you receive will vary depending on lighting, quality of the initial image/object being captured, and distance of the scanner from the image/object.
Page 235 B - Beeper Causes a beep to sound after an image is snapped. No beep (default) Sounds a beep when the image is captured T - Wait for Trigger Waits for a hardware trigger press before taking the image. This is only available when using Photo Style (1P).
Page 236 G - Gain Gain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel value. As you increase the gain, the noise in an image is also amplified. No gain (default) Medium gain Heavy gain Maximum gain...
Page 237: Image Ship - Imgshp
U - Update Tries This sets the maximum number of frames the scanner should take to reach the Delta for Acceptance. Update Tries is only available when using Photo Style (1P). (Default = 6) Range: 0 - 10 % - Target Set Point Percentage Sets the target point for the light and dark values in the captured image.
Page 238: Imgshp Modifiers
IMGSHP Modifiers A - Infinity Filter Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with IMGSNP Modifiers (page 216). Infinity filter off (default) Infinity filter on Example: Infinity Filter off (0A) Infinity Filter on (1A) from approximately 12 feet from approximately 12 feet (3.66m)
Page 239 E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to 24.
Page 240 H - Histogram Stretch Increases the contrast of the transmitted image. Not available with some image formats. No stretch (default) Histogram stretch Example: Histogram Stretch at 0H: Histogram Stretch at 1H: I - Invert Image Invert image is used to rotate the image around the X or Y axis. Invert around the X axis (flips picture upside down) Invert around the Y axis (flips picture left to right) Example:...
Page 241 IF- Noise Reduction Used to reduce the salt and pepper noise in an image. No salt and pepper noise reduction (default) Salt and pepper noise reduction Example: Noise Reduction Off (0if): Noise Reduction On (1if): IR - Image Rotate Image as snapped (rightside up) (default) Rotate image 90 degrees to the right Rotate image 180 degrees (upside down) Rotate image 90 degrees to the left...
Page 242 J - JPEG Image Quality Sets the desired quality when the JPEG image format is selected. Higher numbers result in higher quality, but larger files. Smaller numbers result in greater amounts of lossy compression, faster transmission times, lower quality, but smaller files. (Default = 50) Image is compressed as much as possible while preserving quality factor of n (n = 0 - 100)
Page 243 The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 639. (Default = all rows) Example: Uncropped Image: Image Crop set to Image Crop set to 300R: 300L: Image Crop set to 200B: Image Crop set to 200T: Alternately, specify the number of pixels to cut from the outside margin of the image;...
Page 244 The smaller number of pixels shipped, the smaller the image, however, after a certain point the image becomes unusable. ship every pixel (default) ship every 2nd pixel, both horizontally and vertically ship every 3rd pixel, both horizontally and vertically Pixel Ship Pixel Ship Example: Pixel Ship set to 1S:...
Page 245: Image Size Compatibility
V - Blur Image Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image. Don’t blur (default) Blur Example: Blur Image Off (0V): Blur Image On (1V): W - Histogram Ship A histogram gives a quick picture of the tonal range of an image, or key type.
Page 246: Intelligent Signature Capture - Imgbox
* Native Resolution Intelligent Signature Capture - IMGBOX IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a barcode. This allows you to tailor a signature capture area to a specific form. In order to use IMGBOX, you need a set form where the signature box location is in a known location relative to a barcode.
Page 247: Imgbox Modifiers
To see this example, align the aimer with the signature area (not with the barcode), then press the trigger. Send the following IMGBOX command string after the trigger press: Example: IMGBOX245w37h55y. Note: Case is not important in the command string. It is used here only for clarity. The following image is captured: The IMGBOX commands have many different modifiers that can be used to change the size and appearance of the signature image output by the scanner.
Page 248 B - Output Image Height This option is used to size the image vertically. If using this option, set the resolution (R) to zero. Example: Image Height set to 50B: Image Height set to 100B: D - Pixel Depth This indicates the number of bits per pixel in the transmitted image, which defines whether it will be grayscale or black and white.
Page 249 H - Height of Signature Capture Area The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5. Example: IMGBOX245w37h55y.
Page 250 decimal point between the first and second digit. For example, use 2500 to specify a resolution of 2.5. Set to zero when using the A and B modifiers (see A - Output Image Width B - Output Image Height on page 230). Example: Resolution set to 0R: Resolution set to 1000R:...
Page 251: Rf Default Imaging Device
Y - Vertical Barcode Offset The vertical barcode offset allows you to offset the vertical center of the signature capture area. Negative numbers indicate that the signature capture is above the barcode, and positive numbers indicate that the area is below the barcode. Measurements are in multiples of the minimum bar width.
Page 252 Xenon XP User Guide...
Page 253: Chapter 10 - Utilities
CHAPTER UTILITIES To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page 297 for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.
Page 254: Totalfreedom
Decoding apps and Data Formatting apps can be created using TotalFreedom. For further information about TotalFreedom, go to our website at sps.honeywell.com. Application Plug-Ins (Apps) Any apps that you are using can be turned off or on by scanning the following barcodes.
Page 255: Ezconfig For Scanning Introduction
Configure with EZConfig for Scanning Use the EZConfig for Scanning tool to configure your scanner online: 1. Access the Honeywell Technical Support Downloads Portal at https:// hsmftp.honeywell.com. 2. Go to Software > Barcode Scanners > Software > Tools and Utilities >...
Page 256: Reset The Factory Defaults
Reset the Factory Defaults Caution: This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults barcode, then scan Activate Defaults.
Page 257: Chapter 11 - Serial Programming Commands
CHAPTER SERIAL PROGRAMMING COMMANDS The serial programming commands can be used in place of the programming bar- codes. Both the serial commands and the programming barcodes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming barcode in this manual. The device must be set to an RS232 interface (see page 16).
Page 258: Query Commands
scanner. This setting is changed by using the BT_NAM command, which accepts alphanumeric values. If the name is not known, a wild- card (*) can be used :* Note: Since the base stores all work group settings and transfers to them to scanner once they are linked, changes are typically done to the base and not to the scanner.
Page 259 SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the sub- set of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the spe- cific command identified by the Tag and SubTag fields.
Page 260: Trigger Commands
This response indicates that Codabar Coding Enable (CBRENA) has a range of val- ues from 0 to 1 (off and on). Example: What is the default value for Codabar Coding Enable? Enter: cbrena^. Response: CBRENA1[ACK] This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.
Page 261: Reset The Custom Defaults
The scanner scans until a barcode has been read, until the deactivate command is sent, or until the serial time-out has been reached (see Read Time-Out on page 89 for a description, and the serial command on page 254). Reset the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults barcode below.
Page 262: Menu Commands
ACK/NAK Mode On USBACK1 *ACK/NAK Mode Off USBACK0 Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Aux Port PAPMAG Wincor Nixdorf Terminal PAPWNX Wincor Nixdorf Beetle PAPBTL Xenon XP User Guide...
Page 263 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Wincor Nixdorf RS232 Mode A PAPWMA Program Keyboard *U.S.A. KBDCTY0 Country Albania KBDCTY35 Azeri (Cyrillic) KBDCTY81 Azeri (Latin) KBDCTY80 Belarus KBDCTY82 Belgium KBDCTY1 Bosnia KBDCTY33 Brazil KBDCTY16 Brazil (MS) KBDCTY59 Bulgaria (Cyrillic)
Page 264 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Hungarian (101 key) KBDCTY50 Hungary KBDCTY19 Iceland KBDCTY75 Irish KBDCTY73 Italian (142) KBDCTY56 Italy KBDCTY5 Japan ASCII KBDCTY28 Kazakh KBDCTY78 Kyrgyz (Cyrillic) KBDCTY79 Latin America KBDCTY14 Latvia KBDCTY42 Latvia (QWERTY) KBDCTY43...
Page 265 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Switzerland (German) KBDCTY6 Tatar KBDCTY85 Turkey F KBDCTY27 Turkey Q KBDCTY24 Ukrainian KBDCTY76 United Kingdom KBDCTY7 United Stated (Dvorak right) KBDCTY89 United States (Dvorak left) KBDCTY88 United States (Dvorak) KBDCTY87 United States (International) KBDCTY30...
Page 266 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Keyboard Modifiers *Control + X Off KBDCAS0 DOS Mode Control + X KBDCAS1 Windows Mode Control + X KBDCAS2 Windows Mode Prefix/Suffix Off KBDCAS3 DOS Mode Control + X Mode On KBDCAS4 with Windows Mode Prefix/Suffix Supports ALT 3 Digit HEX Mode...
Page 267 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry RS232 Handshaking *RTS/CTS Off 232CTS0 Flow Control, No Timeout 232CTS1 Two-Direction Flow Control 232CTS2 Flow Control with Timeout 232CTS3 RS232 Timeout (1-5100 232DEL#### milliseconds) *XON/XOFF Off 232XON0 XON/XOFF On 232XON1 *ACK/NAK Off...
Page 268 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Scan While in Base Cradle Scan in Cradle Off (CCB-H-010BT BT_SIC0 default) Scan in Cradle On (CCB01-010BT BT_SIC1 default) Shut Down Scanner in Cradle BT_SIC2 Base Charge Modes Base Charge Off BTRCHG0 *External or Interface Cable Power...
Page 269 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Flexible Power Management for *Full Power (100%) BT_TXP100 Xenon XP 1952g/1952h Medium Power (35%) BT_TXP35 Medium Low Power (5%) BT_TXP5 Low Power (1%) BT_TXP1 Flexible Power Management for *Full Power (100%) BT_TXP8 Xenon XP 1952g-BF/1952h-BF...
Page 270 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Batch Mode Transmit Delay *Off (No Delay) BATDLY0 Short (250 ms) BATDLY250 Medium (500 ms) BATDLY500 Long (1000 ms) BATDLY1000 Multiple Scanner Multiple Scanner Operation BASCON2,DNG3 Operation Scanner Name 0001 BT_NAM0001...
Page 271 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Host Command Acknowledgment Host ACK On HSTACK1 *Host ACK Off HSTACK0 Host ACK Timeout (1-90) *10 HSTATO## Input/Output Selections Power Up Beeper Power Up Beeper Off - Scanner BEPPWR0 *Power Up Beeper On - Scanner BEPPWR1...
Page 272 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Good Read Delay *No Delay DLYGRD0 Short Delay (500 ms) DLYGRD500 Medium Delay (1000 ms) DLYGRD1000 Long Delay (1500 ms) DLYGRD1500 User-Specified Good Read Delay Range 0 - 30,000 ms DLYGRD##### Trigger Modes *Manual Trigger - Normal...
Page 273 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Poor Quality Codes Poor Quality 1D Reading On DECLDI1 *Poor Quality 1D Reading Off DECLDI0 *Poor Quality PDF Reading On PDFXPR10 Poor Quality PDF Reading Off PDFXPR0 Low Resolution PDF Codes On PDFDMI1 *Low Resolution PDF Codes Off...
Page 274 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Aimer Delay 1 millisecond SCNDLY1 250 milliseconds SCNDLY250 500 milliseconds SCNDLY500 *Off (no delay) SCNDLY0 User-Specified Aimer Delay Range 0 - 4,000 ms SCNDLY#### Aimer Mode SCNAIM0 *Interlaced SCNAIM2 Single Code Centering...
Page 275 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Timeout for SEQSAT SEQTIM *Discard Partial Output Sequence SEQTTS0 Default Output Sequence SEQDFT Require Output Sequence Required SEQ_EN2 On/Not Required SEQ_EN1 *Off SEQ_EN0 Good Read Tone - Output Good Read Beep - Each Code in BEPSIN0 Sequences...
Page 276 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Very Low Beeper (Nighttime beplfn0;beplfr10;beppar0;basp Mode) - Cordless Scanner and wr0;beppwr1;baslvl1;beplvl1;be Base pbip1;bepFQ14200;beplot0. Very Low Beeper (Nighttime beplfn0;beplfr10;beppwr1;beplv Mode) - Corded Scanner l1;bepbip1;bepFQ14200;beplot Low Beeper (Daytime Mode) - beplfn0;beplfr10;beppar1;basp Cordless Scanner and Base wr1;beppwr1;baslvl1;beplvl1;be...
Page 277 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Prefix/Suffix Selections Add CR Suffix to All Symbologies VSUFCR Prefix Add Prefix PREBK2## Clear One Prefix PRECL2 Clear All Prefixes PRECA2 Suffix Add Suffix SUFBK2## Clear One Suffix SUFCL2 Clear All Suffixes SUFCA2...
Page 278 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Primary/Alternate Data Formats Primary Data Format ALTFNM0 Data Format 1 ALTFNM1 Data Format 2 ALTFNM2 Data Format 3 ALTFNM3 Single Scan Data Format Change Single Scan-Primary VSAF_0 Data Format Single Scan-Data Format 1 VSAF_1...
Page 279 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Code 39 Append *Off C39APP0 C39APP1 Code 32 Pharmaceutical (PARAF) *Off C39B320 C39B321 Code 39 Full ASCII *Off C39ASC0 C39ASC1 Code 39 Code Page C39DCP Interleaved 2 of 5 Default All Interleaved I25DFT 2 of 5 Settings...
Page 280 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Straight 2 of 5 Industrial Default All Straight 2 of 5 R25DFT Industrial Settings *Off R25ENA0 R25ENA1 Straight 2 of 5 Industrial Message Minimum (1 - 48) *4 R25MIN## Length Maximum (1 - 48) *48...
Page 281 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry GS1-128 Default All GS1-128 Settings GS1DFT GS1ENA1 GS1ENA0 GS1-128 Message Length Minimum (1 - 80) *1 GS1MIN## Maximum (0 - 80) *80 GS1MAX## Telepen Default All Telepen TELDFT Settings *Off...
Page 282 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry UPC-E0 Default All UPC-E UPEDFT Settings UPEEN00 UPEEN01 UPC-E0 Expand *Off UPEEXP0 UPEEXP1 UPC-E0 Addenda Required Required UPEARQ1 *Not Required UPEARQ0 Addenda Timeout Range (0 - 500) *120 DLYADD##### UPC-E0 Addenda Separator UPEADS1...
Page 283 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry EAN-13 Beginning with 378/379 *Don’t Require Addenda ARQ3780 Addenda Required Require 2 Digit Addenda ARQ3781 Require 5 Digit Addenda ARQ3782 Require 2 or 5 Digit Addenda ARQ3783 EAN-13 Beginning with 414/419 *Don’t Require Addenda ARQ4140...
Page 284 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Default All MSI Settings MSIDFT *Off MSIENA0 MSIENA1 MSI Check Character *Validate Type 10, but Don’t MSICHK0 Transmit Validate Type 10 and MSICHK1 Transmit Validate 2 Type 10 Chars, but MSICHK2 Don’t Transmit Validate 2 Type 10 Chars and...
Page 285 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Codablock F Default All Codablock F Settings CBFDFT *Off CBFENA0 CBFENA1 Codablock F Msg. Length Minimum (1 - 2048) *1 CBFMIN#### Maximum (1 - 2048) *2048 CBFMAX#### Label Code LBLENA1 *Off...
Page 286 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry QR Code Append *One Scan QRCAPP1 Swipe QRCAPP2 Point & Shoot QRCAPP3 QRCAPP0 QR Code Page QR Code Page (*3) QRCDCP## DotCode Default All DotCode Settings DOTDFT DOTENA1 *Off DOTENA0...
Page 287 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Aztec Code Default All Aztec Code Settings AZTDFT AZTENA1 AZTENA0 Aztec Code Msg. Length Minimum (1-3832) *1 AZTMIN#### Maximum (1-3832) *3832 AZTMAX#### Aztec Append AZTAPP1 AZTAPP0 Aztec Code Page Aztec Code Page (*51) AZTDCP## Chinese Sensible (Han Xin) Code...
Page 288 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Planet and Postal-4i On POSTAL13 Planet and Intelligent Mail POSTAL15 Barcode On Planet, Postnet, and Postal-4i On POSTAL21 Planet, Postnet, and Intelligent POSTAL22 Mail Barcode On Planet, Postal-4i, and Intelligent POSTAL23 Mail Barcode On Postnet, Postal-4i, and Intelligent...
Page 289 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Korea Post Msg. Length Minimum (2 - 80) *4 KPCMIN## Maximum (2 - 80) *48 KPCMAX## Korea Post Check Digit Transmit Check Digit KPCCHK1 *Don’t Transmit Check Digit KPCCHK0 Imaging Default Commands Image Snap...
Page 290 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry File Format - TIFF binary group 4, IMGFMT2 compressed File Format - TIFF grayscale IMGFMT3 File Format - Uncompressed IMGFMT4 binary File Format - Uncompressed IMGFMT5 grayscale File Format - BMP IMGFMT8 *Histogram Stretch Off...
Page 291 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Ship Histogram IMGHST1 Image Size Compatibility Force VGA Resolution IMGVGA1 *Native Resolution IMGVGA0 Intelligent Signature Capture Optimize On DECBND1 *Optimize Off DECBND0 Utilities Add Code I.D. Prefix to All Symbologies (Temporary) PRECA2,BK2995C80! Show Software Revision REVINF...
Page 292 Xenon XP User Guide...
Page 293 CHAPTER PRODUCT SPECIFICATIONS Xenon XP 1950g/1950h Corded Scanner Product Specifications Parameter Specification Mechanical Height 6.3 inches (160mm) Length 4.1 inches (104mm) Width 2.8 inches (71mm) Weight General Duty 5.3 ounces (150g) Healthcare 5.5 ounces (155g) Electrical Voltage Requirements 4.4 to 5.5 VDC at input connector Current Draw ScanningStandby 500mA @ 5VDC, 2.5W...
Page 294 Parameter (Continued) Specification Mechanical Drop Operational after 50 drops from 6 feet (1.8m) to concrete ESD Tolerance Up to 15kV direct air Up to 8 kV indirect coupling plane Sealant Rating IP52 Image Image Size 1280 x 800 pixels Scan Performance Skew Angle +65°...
Page 295 Parameter (Continued) Specification Peak Wavelength LED 624nm + 18nm (red LED) 520nm + 18nm (green LED) IEC 62471: “Exempt Risk Group” Battery Lithium Ion 2400 mAHr minimum Number of Scans Up to 65,000 per charge Expected Hours of Operation Expected Charge Time 4.5 hours Radio Frequency...
Page 296 *Storage outside of this temperature range could be detrimental to battery life. Xenon XP 1952g-BF/1952h-BF Scanner Product Specifications Parameter Specification Mechanical Height 6.3 inches (160mm) Length 4.1 inches (104mm) Width 2.8 inches (71mm) Weight General Duty 6.9 ounces (195g) Healthcare 7.1 ounces (201g) Use Time # of Scans per full charge...
Page 297 Parameter (Continued) Specification Image Image Size 1280 x 800 pixels Scan Performance Skew Angle +65° Pitch Angle 1D barcode 1D barcodes: +65° 2D barcode 2D barcodes: +45° Motion Tolerance Up to 4.0 m/s (157 in/s) for 13 mil UPC at optimal focus Symbol Contrast 20% or greater (Grade A)
Page 298 Parameter (Continued) Specification Temperature Ranges: Operating 32° F to +122° F (0° C to +50° C) Storage -40° F to +158° F (-40° C to +70° C) Humidity Up to 95% non-condensing Mechanical Drop Operational after 50 drops from 3.28 feet (1 m) to concrete Vibration 5G Peak from 22Hz to 300Hz...
Page 299 Parameter (Continued) Specification Temperature Ranges: Operating/Battery Charge 41° F to +104° F (5° C to +40° C) Storage without battery -40° F to +158° F (-40° C to +70° C) Humidity Up to 95% non-condensing Mechanical Drop Operational after 50 drops from 3.3 feet (1m) to concrete Vibration 5G Peak from 22Hz to 300Hz...
Page 300 Focus (Continued) Standard Range High Density Ultra High Density Symbology Near Near Near (Continued) Distance Distance Distance Distance Distance Distance 5 mil Data Matrix 7.5 mil Data Matrix 10 mil Data Matrix 4 mil QR Code 10 mil QR Code 20 mil QR Code 17.2 13.0...
Page 301 Focus (Continued) Standard Range High Density Ultra High Density Symbology Near Near Near (Continued) Distance Distance Distance Distance Distance Distance 5 mil PDF417 6.7 mil PDF417 5 mil Data Matrix 7.5 mil Data Matrix 10 mil Data Matrix 4 mil QR Code 10 mil QR Code 20 mil QR Code 13.8...
Page 302 10.2 Standard Connector Pinouts Note: The following pin assignments are not compatible with some Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
Page 303 Keyboard Wedge 10 Pin RJ41 Modular Plug - connects to the base Cable shield Cable select Supply ground Terminal data Terminal clock Keyboard clock +5V power Keyboard data Serial Output 10 Pin RJ41 Modular Plug - connects to the base Cable shield Cable select Supply ground...
Page 304 Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner +5V power Transmit Enable 10 Pin Modular Plug - connects to the base Cable shield Cable select Supply ground +5V power Data + 10 Data - Xenon XP User Guide...
Page 305 Required Safety Labels Scanner Illumination output Part Compliance Number, Label location Serial Number and Revision Information location Xenon XP User Guide...
Page 306 CCB01-010BT/CCB01-010BT-BF Base Part Number, Serial Number and Compliance Label Revision locations Information location Xenon XP User Guide...
Page 307 CCB-H-010BT/CCB-H-010BT-BF Base Compliance label locations Xenon XP User Guide...
Page 308 Xenon XP User Guide...
Page 309 CHAPTER MAINTENANCE AND TROUBLESHOOTING Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support page xvii). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following sections describe periodic checks to ensure dependable operation.
Page 310 (DRH) for the healthcare and general-purpose markets. Please refer to the Honeywell Safety and Productivity Solutions website for specific details on how to clean Xenon XP scanners with disinfectant-ready housings. Helpful information on the care of these specialty products can be found in the following articles: •...
Page 311 Replace an Interface Cable 1. Turn off the power to the host system. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the back of the scanner’s handle. This is the cable release. 4.
Page 312 5. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Change a Scanner Battery 1. Grasp the wing connector or use a Phillips head screwdriver to remove the screw from the end cap.
Page 313 Troubleshoot a Cordless System Troubleshoot a Base Note: Go to sps.honeywell.com and then select Support > Software and Downloads to check for the latest software for both the scanner and the base. If your base is not functioning properly, review the following troubleshooting guidelines to try to isolate the problem.
Page 314 • Aren’t coated with frost or water droplets on the surface. • Are enabled in the base or Access Point to which the scanner connects. Is the barcode displayed but not entered into the application? The barcode is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example).
Page 315 Refer to Data Edit beginning on page 125 and Data Format beginning on page 131 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Linear Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...
Page 316 0, 1, 2, 3, 8, 9, A, B, C UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity 2D Symbologies...
Page 317 Honeywell Possible modifiers 2D Symbology Chinese Sensible Code (Han Xin Code) Codablock A 0, 1, 4, 5, 6 Codablock F 0, 1, 4, 5, 6 Code 49 0, 1, 2, 4 Data Matrix Dot Code GS1 Composite GS1 DataBar Omnidirectional...
Page 318 ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.
Page 319 Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. Printable Characters Character Character DEC Character " & < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ €...
Page 320 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Œ î Reserved ì Reserved Ž Ä Numeric Keypad Enter 0x1C Å Numeric Keypad / 0x35 É 0x3B ‘ æ 0x3C ’ Æ 0x3D “ ô 0x3E ” ö...
Page 321 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Â ┬ Ã ├ Ä ─ Å í Æ ╞ Ç ╟ È ╚ É ╔ Ê ╩ Ë ╦ Ì ╠ Í ═ Î ╬ Ï ╧ Ð...
Page 322 (standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
Page 323 Honeywell Code Page Selection Method/ Keyboard Code Standard Country Country Page Option Spain ISO/IEC 646-17 Spain ISO/IEC 646-85 Xenon XP User Guide...
Page 324 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ‾ ¥ ‾ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...
Page 325 Keyboard Key References 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
Page 326 Xenon XP User Guide...
Page 327 SAMPLE SYMBOLS UPC-A Interleaved 2 of 5 01234567890 0 123456 7890 EAN-13 9 780330 290951 Code 128 Code 39 Code 128 BC321 Codabar A13579B Code 93 Straight 2 of 5 Industrial 123456 123456-9$ Matrix 2 of 5 6543210 RSS-14 PDF417 Car Registration (01) 00123456789012 Code 49...
Page 328 SAMPLE SYMBOLS (CONTINUED) Postnet Data Matrix Zip Code Test Symbol QR Code Numbers MaxiCode Micro PDF417 Test Message Test Message DotCode 12345 Xenon XP User Guide...
Page 329 PROGRAMMING CHART Xenon XP User Guide...
Page 330 PROGRAMMING CHART (CONTINUED) Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again. Xenon XP User Guide...
Page 332 Honeywell 855 S. Mint Street Charlotte, NC 28202 sps.honeywell.com ™ XEN195X-EN-UG-01 Rev N 2/22...

This manual is also suitable for:

Xenon xp 1950g Xenon xp 1950h Xenon xp 195g Xenon xp 1952g-bf Xenon xp 1952h-bf Ccb01-010bt ... Show all

Honeywell Xenon XP 195 Series User Manual

Chapter 1 - Get Started

Chapter 2 - Program the Interface

Chapter 3 - Cordless System Operation

Chapter 4 - Input/Output Settings

Chapter 5 - Healthcare Settings

Chapter 6 - Data Edit

Chapter 7 - Data Format

Chapter 8 - Symbologies

Quick Links

Related Manuals for Honeywell Xenon XP 195 Series

Summary of Contents for Honeywell Xenon XP 195 Series