Honeywell Voyager 1202G-BF User Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Barcode Reader
  5. VOYAGER 1202G BF
  6. User manual

Honeywell Voyager 1202G-BF User Manual

Single-line laser bar code scanner
Hide thumbs Also See for Voyager 1202G-BF:
Table of Contents

Quick Links

Voyager™ 1200g/1202g/1202g-BF
Single-Line Laser Bar Code Scanner
User's Guide
Table of Contents
loading

Related Manuals for Honeywell Voyager 1202G-BF

Summary of Contents for Honeywell Voyager 1202G-BF

  • Page 1 Voyager™ 1200g/1202g/1202g-BF Single-Line Laser Bar Code Scanner User’s Guide...
  • Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.

  • Page 3: Table Of Contents

    ® Verifone Ruby Terminal Default Settings................2-7 ® Gilbarco Terminal Default Settings ..................2-8 Honeywell Bioptic Aux Port Configuration ................2-8 © Datalogic™ Magellan Bioptic Aux Port Configuration............2-8 NCR Bioptic Aux Port Configuration ..................2-9 Wincor Nixdorf Terminal Default Settings ................2-9 Wincor Nixdorf Beetle™ Terminal Default Settings ............2-10 Wincor Nixdorf RS232 Mode A ..................2-10...
  • Page 4 Keyboard Wedge Modifiers ....................2-19 ALT Mode ........................2-19 Keyboard Style ......................2-19 Keyboard Conversion ....................2-20 Keyboard Modifiers...................... 2-20 Inter-Scan Code Delay ....................2-21 Break Character ....................2-22 Keyboard Wedge Defaults................... 2-22 RS232 Modifiers ........................ 2-23 RS232 Baud Rate......................2-23 RS232 Word Length: Data Bits, Stop Bits, and Parity ..........
  • Page 5 Auto Reconnect Mode ....................3-17 Maximum Link Attempts ....................3-18 Bluetooth/ISM Network Activity Examples..............3-18 Reset Scanner and Base....................3-19 Chapter 4 - Cordless System Operation (Voyager 1202g-BF) How the Charge and Communications Base Works ............4-1 Linking the Scanner to a Base..................... 4-1...
  • Page 6 Communication Between the Cordless System and the Host........................4-1 RF (Radio Frequency) Module Operation ................4-2 System Conditions....................... 4-2 Linking Process ......................4-2 Scanner Is Out of Range ....................4-2 Scanner Is Moved Back Into Range ................4-2 Page Button ........................4-3 About the Instant Charge Pack....................
  • Page 7 Good Read and Error Indicators..................5-1 Beeper – Good Read..................... 5-1 Beeper Volume – Good Read..................5-2 Beeper Pitch – Good Read.................... 5-2 Beeper - Transmit Order....................5-2 Beeper Pitch – Error ...................... 5-3 Beeper Duration – Good Read ..................5-3 Number of Beeps –...
  • Page 8 Prefix Selections........................6-2 Suffix Selections ........................6-2 Transmit Alternate Extended ASCII Characters ..............6-3 Function Code Transmit ...................... 6-4 Communication Check Character..................6-4 Intercharacter, Interfunction, and Intermessage Delays............6-5 Intercharacter Delay ...................... 6-5 User Specified Intercharacter Delay ................6-5 Interfunction Delay......................6-6 Intermessage Delay.......................
  • Page 9 Read Time-Out ......................11-3 Menu Commands ......................11-4 Chapter 12 - Product Specifications Voyager 1200g Product Specifications................12-1 Voyager 1202g and Voyager 1202g-BF Product Specifications ........12-2 CCB00-010BT Product Specifications................12-3 CCB00-010BT-01N-BF Product Specifications ..............12-4 CCB00-010BT/CCB00-010BT-01N-VBF Mounting ............12-5...
  • Page 10 Standard Cable Pinouts..................... 12-5 Keyboard Wedge ......................12-5 Serial Output ....................... 12-6 RS485 Output ......................12-6 USB ..........................12-6 Chapter 13 - Maintenance and Troubleshooting Repairs ..........................13-1 Maintenance ........................13-1 Cleaning the Device..................... 13-1 Inspecting Cords and Connectors ................13-1 Replacing Cables in Corded Scanners................

  • Page 11: Chapter 1 - Getting Started

    Product specifications, dimensions, warranty, and customer support information are also included. Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.

  • Page 12: Connecting With Keyboard Wedge

    1. Connect the appropriate interface cable to the scanner first, then to the computer. Charge and Communications Base USB Connection: optional power supply 2. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal surface.
  • Page 13 2. Connect the appropriate interface cable to the scanner and to the terminal/computer. Note: For Voyager 1202g-BF, you must use the power supply. only if power supply is included Charge and Communications Base Keyboard Wedge Connection: 3. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal surface.

  • Page 14: Connecting With Rs232 Serial Port

    Connecting with RS232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner or base to work properly, you must have the correct cable for your type of terminal/computer. only if power supply is...

  • Page 15: Connecting With Rs485

    Connecting with RS485 A scanner or base can be connected for an IBM POS terminal interface. 1. Connect the appropriate interface cable to the device, then to the computer. Charge and Communications Base RS485 Connection: 2. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal surface.

  • Page 16: Reading Techniques

    Menu Bar Code Security Settings Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Please contact the nearest techni-...

  • Page 17: Resetting The Custom Defaults

    Resetting the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings.
  • Page 18 1 - 8...

  • Page 19: Chapter 2 - Programming The Interface

    Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the bar code below.

  • Page 20: Rs485

    RS485 Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface. Note: After scanning one of these codes, you must power cycle the cash register. IBM Port 5B Interface IBM Port 9B HHBCR-1 Interface IBM Port 17 Interface IBM Port 9B...

  • Page 21: Usb Ibm Surepos

    Option Setting Symbologies Enable UPC-A with check digit and number system Enable UPC-E0 with check digit Enable EAN/JAN-8 with check digit Enable EAN/JAN-13 with check digit Enable Code 128 Enable Code 39 Enable OPOS with automatic disable off OPOS Mode USB IBM SurePos Scan one of the following “Plug and Play”...

  • Page 22: Usb Pc Or Macintosh Keyboard

    Disable Secondary Interface USB PC or Macintosh Keyboard Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard. Scanning these codes also adds a CR and LF for Voyager 1200g and adds CR for Voyager 1202g and 1202g-BF. USB Keyboard (Mac) USB Japanese Keyboard (PC) USB HID...

  • Page 23: Usb Serial Commands

    Scan one of the following codes to program the scanner to emulate a regular RS232-based COM Port. If you are using a Microsoft® Windows® PC, you will need to download the USB serial driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recog- nize the scanner as a USB CDC class device and automatically use a class driver.

  • Page 24: Ack/Nak Mode

    ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off Communication Timeout This allows you to set the length (in milliseconds) for a timeout for the host ACK/NAK response. Scan the bar code below, then set the timeout (from 0-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.

  • Page 25: Support Bel/Can In Ack/Nak

    Support BEL/CAN in ACK/NAK This protocol responds to and commands when in ACK/NAK mode. The scanner sounds an error tone when a command is sent from the host. terminates the transmission. Default = BEL/CAN Off. BEL/CAN On * BEL/CAN Off ®...

  • Page 26: Gilbarco ® Terminal Default Settings

    Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit. Character RTS/CTS with tim- eout and 232 ACK/NAK are also enabled.

  • Page 27: Ncr Bioptic Aux Port Configuration

    NCR Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 9600 bps and the data format to 7 data bits, Even parity, 1 stop bit and Message RTS/CTS with time- out.

  • Page 28: Wincor Nixdorf Beetle™ Terminal Default Settings

    Wincor Nixdorf Beetle™ Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal. The following prefixes are programmed for each symbology: Symbology Prefix Symbology Prefix Aztec Code Interleaved 2 of 5 Codabar MaxiCode Code 93...
  • Page 29 By default, national character replacements are used for the following characters: #$@[\]^‘{|}~ Refer to the ISO 2022/ISO 646 Character Replacements on page A-7 chart to view the character replacements for each country. Keyboard Countries * United States Albania Arabic Azeri (Cyrillic) Azeri (Latin) Belarus Belgium...
  • Page 30 Keyboard Countries (Continued) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) China Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark 2 - 12...
  • Page 31 Keyboard Countries (Continued) Dutch (Netherlands) Estonia Faroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) 2 - 13...
  • Page 32 Keyboard Countries (Continued) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy 2 - 14...
  • Page 33 Keyboard Countries (Continued) Japan ASCII Korea Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta 2 - 15...
  • Page 34 Keyboard Countries (Continued) Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) 2 - 16...
  • Page 35 Keyboard Countries (Continued) Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) 2 - 17...
  • Page 36 Keyboard Countries (Continued) Tatar Thailand Turkey F Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United Stated (Dvorak right) United States (International) Uzbek (Cyrillic) 2 - 18...

  • Page 37: Keyboard Wedge Modifiers

    Keyboard Countries (Continued) Vietnam Keyboard Wedge Modifiers ALT Mode If your bar code contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode. (See "Extended ASCII Characters" on page A-4.) Note: Scan the ALT mode bar code after scanning the appropriate Keyboard Country code.

  • Page 38: Keyboard Conversion

    Autocaps via NumLock bar code should be scanned in countries (e.g., Germany, France) where the Caps Lock key can- not be used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve the current state of the Caps Lock.

  • Page 39: Inter-Scan Code Delay

    Default = Control + X Mode Off. Windows Mode Control + X Mode On * Control + X Mode Off DOS Mode Control + X Mode On Windows Mode Prefix/Suffix Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off. Numeric Keypad Mode On * Numeric Keypad Mode Off Inter-Scan Code Delay...

  • Page 40: F0> Break Character

    Break Character When your keyboard detects that any key is being pressed, released, or held down, the keyboard sends a packet of infor- mation known as a “scan code” to your computer. There are two different types of scan codes: “make codes” and “break codes.”...

  • Page 41: Rs232 Modifiers

    RS232 Modifiers RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 9600. 1200 2400 4800 * 9600 19200 38400...

  • Page 42: Rs232 Word Length: Data Bits, Stop Bits, And Parity

    RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select 8 data bits per character.

  • Page 43: Rs232 Handshaking

    7 Data, 2 Stop, Parity Space 8 Data, 1 Stop, Parity Space 7 Data, 1 Stop, Parity Mark 7 Data, 2 Stop, Parity Mark 8 Data, 1 Stop Parity Mark RS232 Handshaking RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. RTS/CTS Off: RTS/CTS is turned off so no data flow control is used, but RTS is still active.

  • Page 44: Rs232 Timeout

    Flow Control, No Timeout Character-Based Flow Control, No Timeout Two-Direction Flow Control Flow Control with Timeout Character-Based Flow Control with Timeout RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-65535 milli- seconds) by scanning digits from the Programming...

  • Page 45: Ack/Nak

    ACK/NAK After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK is received, the last set of bar code data is retransmitted and the scanner waits for ACK/NAK again.

  • Page 46: Nak Retries

    NAK Retries This selection limits the number of NAK retries that can occur in ACK/NAK mode. Scan the bar code below, then set the number of retries (from 0-255) by scanning digits from the Programming Chart, then scanning Save. (5 is the recom- mended setting.) Default = 0, or disabled.

  • Page 47: Block Check Character

    Block Check Character When this selection is set to Transmit, the NCR Block Check Character (BCC) is expected with incoming messages and transmitted with outgoing messages. Default = Transmit. * Transmit Don’t Transmit NCR Prefix This selection allows you to program an NCR-specific prefix. Refer to the ASCII Conversion Chart (Code Page 1252), page A-2 to find the hex equivalent for the characters you want for the NCR prefix (typically, 02 for STX).

  • Page 48: Ncr Nof (Not-On-File) Error

    Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 Timeout must be set to 3000 in order to communicate with a bioptic scanner.

  • Page 49: Communication Timeout

    Communication Timeout This allows you to set the length (in milliseconds) for a timeout for the host ACK/NAK response. Scan the bar code below, then set the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save. Default = 2000 ms.
  • Page 50 2 - 32...

  • Page 51: Chapter 3 - Cordless System Operation (Voyager 1202G)

    Note: This chapter applies only to Voyager 1202g cordless scanning systems. It does not apply to corded or Voyager 1202g- BF scanners. See Cordless System Operation (Voyager 1202g-BF) on page 4-1 for Voyager 1202g-BF scanners (PN: 1202G-BF). How the Charge and Communications Base Works A charge and communications base provides the link between the cordless scanner and the host system.

  • Page 52: Rf (Radio Frequency) Module Operation

    When data is scanned, the data is sent to the host system via the base. The cordless scanner recognizes data acknowledge- ment (ACK) from the base. If it cannot be determined that the data has been properly sent to the base, the scanner issues an error indication.

  • Page 53: Page Button

    (page 3-8) if you need to charge a scanner without linking it to the base. The model Voyager 1202g is designed for use with Honeywell battery pack model 100000495 (Li-ion 3.7Vdc, 7.4 watt hour), or model BAT-SCN01 (Li-ion 3.75Vdc, 9.0 watt hour).

  • Page 54: Battery Recommendations

    • Although your battery can be recharged many times, it will eventually be depleted. Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page 14-1 for additional information.

  • Page 55: Scanner Led Sequences And Meaning

    Scanner LED Sequences and Meaning Note: Pressing the button on the scanner causes the LED to glow red until it communicates successfully with the base. LED Indication Beeper Indication Cause Normal Operation Red Flash None Battery low Green Flash 1 beep Successful communication or linking Red, blinking Razz or error tone...

  • Page 56: Reset Scanner

    Reset Scanner Scanning this bar code reboots the scanner and causes it to relink with the base. Reset Scanner Scanning While in Base Cradle If you want to be able to scan bar codes while the scanner is in the base, scan the following Scanning in Cradle On bar code. If you want to only allow scanning when the scanner is out of the base, scan Scanning in Cradle Off.

  • Page 57: Paging

    External Power Only Paging Paging Mode By default, the paging button on the base pages the scanner associated with that base. If you want the paging button on your base to be disabled, scan the following Paging Mode Off bar code. When Paging Mode is off, the base will no longer page the scanner when the button is pressed.

  • Page 58: Base Address

    Base Address Scan the following bar code to determine the address of the base you are using. Base Address Scanner Modes The Voyager is capable of working with Bluetooth devices other than the CCB00-010BT base. Charge Only Mode There may be times when you want to charge your scanner, but not link to the base. For example, if a scanner is linked to a Bluetooth device and you need to charge the scanner, but want to retain your existing link.

  • Page 59: Unlinking The Scanner

    Open Link Mode - Single Scanner When newly shipped or defaulted to factory settings, a scanner is not linked to a base. A link is established when the scanner is placed into a base. When in Open Link Mode, a new link is established when a new scanner is placed in the base.

  • Page 60: Alarm Duration

    Alarm Duration To set the the length of time you want the Out-of-Range alarm to sound, scan the following bar code and then set the time- out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save.

  • Page 61: Batch Mode

    Batch mode is used to store bar code data when a scanner is out of range of its base, or when performing inventory. The data is transmitted to the base once the scanner is back in range or when the records are manually transmitted. Note: Batch Mode is only supported by the Honeywell Charge and Communication Base (CCB) and Honeywell Access Point (AP).

  • Page 62: Batch Mode Quantity

    Batch Mode Quantity When in Inventory Batch Mode (page 3-11), you may wish to transmit the number of multiple bar codes scanned, rather than a single bar code multiple times. For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off, when you transmit your data it will appear as XYZ three times.

  • Page 63: Delete Last Code

    Delete Last Code If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code. Delete Last Code Record Counter If you wish to add a record counter to each bar code scanned in Batch Mode, scan Record Counter On. Your batch output would add a sequential number before each bar code, for example: 00001,bar code 1 00002,bar code 2...

  • Page 64: Total Records

    Default = Record Counter Off. * Record Counter Off Record Counter On Total Records If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records. Total Records Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO.

  • Page 65: Clear All Codes

    Clear All Codes If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes. Clear All Codes Transmit Records Automatically If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-11), you can transmit all stored data to the host system when the scanner is placed in the base.

  • Page 66: Scanner Name

    Batch Mode Transmit Delay Medium (500 ms) Batch Mode Transmit Delay Long (1000 ms) Scanner Name You may assign a name to each scanner you are using for identification purposes. The default name is “Voyager.” Perform the rename operation using either the bar codes on page 3-17, or by sending the serial command :*:BT_NAMname.

  • Page 67: Using The Scanner With Bluetooth Devices

    You may also scan the following Scanner Name bar code and scan up to 30 numbers and/or letters for the scanner name. For example, if you wanted to name the linked scanner “312,” you would scan the following bar code, scan the 3, 1, and 2 bar codes on the Programming Chart inside the back cover of this manual, then scan Save.

  • Page 68: Maximum Link Attempts

    Auto Reconnect Off The following table shows the results of the Auto Reconnect On and Off settings: Event Auto Reconnect On Auto Reconnect Off Scanner out of range Relink occurs automatically. If maximum The scanner is relinked by pressing number of link attempts is unsuccessful, the button.

  • Page 69: Reset Scanner And Base

    When the scanner goes out of range, 15 attempts are made to link to the base unit. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base, but retains any bar codes that may have been saved in batch mode.
  • Page 70 3 - 20...

  • Page 71: Chapter 4 - Cordless System Operation (Voyager 1202G-Bf)

    Cordless System Operation (Voyager 1202g-BF) Note: This chapter applies only to Voyager 1202g-BF cordless scanning systems (PN: 1202G-BF). It does not apply to corded or Voyager 1202g scanners. See Cordless System Operation (Voyager 1202g) on page 3-1 for Voyager 1202g scanners.

  • Page 72: Rf (Radio Frequency) Module Operation

    When data is scanned, the data is sent to the host system via the base. The cordless scanner recognizes data acknowledge- ment (ACK) from the base. If it cannot be determined that the data has been properly sent to the base, the scanner issues an error indication.

  • Page 73: Page Button

    Voyager 1202g-BF scanner can only be charged by CCB00-010BT-01N-BF base. Caution: Use of any non-Honeywell power supply may result in damage not covered by the warranty. Note: If you are powering the base through the interface cable (for example, a USB cable) and not using an external power supply plugged into the auxiliary port located on the bottom of the base, the current available for charging is reduced and the charge time is significantly increased.

  • Page 74: Base Led Sequences And Meaning

    Base LED Sequences and Meaning The base contains a red LED that indicate the status of the unit and verifies its communication with the host system. The base also has a green LED that indicates the scanner instant charge pack charge condition. The red LED and the green LED both flash when a link is established.

  • Page 75: Scanning While In Base Cradle

    Scanning While in Base Cradle If you want to be able to scan bar codes while the scanner is in the base, scan the following Scanning in Cradle On bar code. If you want to only allow scanning when the scanner is out of the base, scan Scanning in Cradle Off. Default = Scanning in Cradle On.

  • Page 76: Scanner Address

    Base Address Scanner Modes The Voyager 1202g-BF is only capable of working with the CCB00-010BT-01N-BF base. Charge Only Mode There may be times when you want to charge your scanner, but not link to the base. For example, if a scanner is linked to a Bluetooth device and you need to charge the scanner, but want to retain your existing link.

  • Page 77: Unlinking The Scanner

    Locked Link Mode - Single Scanner If you link a scanner to a base using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base. If you do place a different scanner into a base, it will charge the scanner, but the scanner will not be linked.

  • Page 78: Alarm Duration

    The sounds are as follows: Setting Sound 3 long beeps, medium pitch 3 long beeps, high pitch Scanner Alarm Type Alarm Duration To set the length of time you want the Out-of-Range alarm to sound, scan the following bar code and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save.

  • Page 79: Maximum Link Attempts

    The following table shows the results of the Auto Reconnect On and Off settings: Event Auto Reconnect On Auto Reconnect Off Scanner out of range Relink occurs automatically. If maximum The scanner is relinked by pressing number of link attempts is unsuccessful, the scanner’s button.

  • Page 80: Reset Scanner And Base

    When the scanner goes out of range, no action is taken to relink. When the scanner’s button is pressed, 15 attempts are made to link to the base. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time.

  • Page 81: Chapter 5 - Input/Output Settings

    The scanner can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner. Note: The Voyager 1202g-BF does not issue a power up beep when the scanner is in the base. Power Up Beeper Off -...

  • Page 82: Beeper Volume - Good Read

    Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High. Medium * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (2350 Hz) High (4200 Hz)

  • Page 83: Beeper Pitch - Error

    Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = Razz. * Razz (100 Hz) Medium (2000 Hz) High (4200 Hz) Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read.

  • Page 84: Led Indicators

    To change the number of error beeps, scan the following bar code and then scan a digit (1-9) bar code and the Save code on the Programming Chart inside the back cover of this manual. Default = 1. Number of Error Beeps/LED Flashes LED Indicators The green and red LEDs can be programmed to be On or Off and at different brightness levels to indicate various scanner states.

  • Page 85: Led Brightness

    Red LED On when Battery is Low Green LED On when Battery is Low LED Brightness Default = Red High, Green High. Note: For Voyager 1202g-BF, all LED Brightness settings result in High brightness. Red Off Green Off Red Low...

  • Page 86: In-Stand And Out-Of-Stand Settings

    Green Low Red Medium Green Medium * Red High * Green High In-Stand and Out-Of-Stand Settings The following settings program the scanner’s behavior when it is either in the stand, or out of the stand (hand-held). Caution: When working with In-Stand and Out-of-Stand settings, enable the settings you want before disabling those you do not want to use.

  • Page 87: Manual Activation Mode

    Presentation Mode with CodeGate Out-of-Stand: When the scanner is not in the stand, it automatically detects bar codes and decodes them. However, the data is not transmitted until you press the button. The laser remains on briefly after the transmission. (If you are accustomed to a Voyager 9540, this setting is the same as the 9540’s default.) Presentation Mode Out-of-Stand Presentation Mode with...

  • Page 88: Manual Activation Laser Timeout - Button Settings

    * End Manual Activation After Good Read In-Stand Do Not End Manual Activation After Good Read Out-of-Stand * End Manual Activation After Good Read Out-of-Stand Manual Activation Laser Timeout - Button Settings You can set a timeout for the length of time the laser remains on and attempting to decode bar codes when the button is held down, and after it is released.

  • Page 89: Codegate

    CodeGate When CodeGate is On, the button is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the button is pressed. When CodeGate is Off, bar code data is transmitted when it is decoded.

  • Page 90: End Object Detection After Good Read

    * Object Detection Mode On In-Stand * Object Detection Mode Off Out-of-Stand Object Detection Mode On Out-of-Stand End Object Detection After Good Read After a bar code is successfully detected and read from the scanner, the laser can be programmed either to remain on and scanning, or to turn off.

  • Page 91: Object Detection Laser Timeout

    Object Detection Laser Timeout You can set a timeout for the length of time the laser remains on and attempting to decode bar codes after an object is detected. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1- 65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.

  • Page 92: Activation Character

    Activation Character This sets the character used to trigger scanning when using Character Activation Mode. On the ASCII Conversion Chart (Code Page 1252), page A-2, find the hex value that represents the character you want to use to trigger scanning. Scan the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that ASCII...

  • Page 93: Deactivation Character

    Deactivation Character This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion Chart (Code Page 1252), page A-2, find the hex value that represents the character you want to use to terminate scanning. Scan the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that...

  • Page 94: Output Sequence Overview

    Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the Default Sequence symbol programs the scanner to the following Universal values.
  • Page 95 SEQBLKsequence editor start command code identifier for Code 39 9999 code length that must match for Code 39, 9999 = all lengths start character match for Code 39, 41h = “A” termination string for first code code identifier for Code 128 9999 code length that must match for Code 128, 9999 = all lengths start character match for Code 128, 42h = “B”...

  • Page 96: Output Sequence Editor

    Output Sequence Editor Enter Sequence Default Sequence Sequence Timeout You may wish to set the maximum time between bar code scans in an output sequence. If that maximum time is not met, the output sequence operation is terminated. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning...

  • Page 97: Require Output Sequence

    * Discard Partial Sequence Require Output Sequence When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. When it’s On/Not Required, the scanner will attempt to get the output data to conform to an edited sequence but, if it cannot, the scanner transmits all output data to the host device as is.
  • Page 98 5 - 18...

  • Page 99: Chapter 6 - Data Editing

    Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.

  • Page 100: To Clear One Or All Prefixes Or Suffixes

    Example: Add a Tab Suffix to All Symbologies Step 1. Scan Add Suffix. Step 2. Scan 9, 9 from the Programming Chart inside the back cover of this manual to apply this suffix to all symbologies. Step 3. Scan 0, 9 from the Programming Chart inside the back cover of this manual.

  • Page 101: Transmit Alternate Extended Ascii Characters

    Clear One Suffix Clear All Suffixes Transmit Alternate Extended ASCII Characters You may need to emulate special keyboard functions, such as up or down arrows, Alt/Make or Alt/Break commands, that are not supported in the Extended ASCII Character table. Refer to Alternate Extended ASCII Characters (page 6-3) for a range of key- board function keys and corresponding decimal and hex characters.

  • Page 102: Function Code Transmit

    Alternate Extended ASCII Characters (Continued) DEC HEX Keyboard Function DEC HEX Keyboard Function 142 8E Numeric Keypad Enter 166 A6 143 8F Numeric Keypad / 167 A7 Shift Tab 144 90 168 A8 Enter 145 91 169 A9 146 92 170 AA Alt Make 147 93 171 AB Alt Break...

  • Page 103: Intercharacter, Interfunction, And Intermessage Delays

    Intercharacter, Interfunction, and Intermessage Delays Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage delays slow the transmission of data, increasing data integrity. Intercharacter Delay An intercharacter delay of up to 327675 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data.

  • Page 104: Interfunction Delay

    Interfunction Delay An interfunction delay of up to 327675 milliseconds (in 5ms increments) may be placed between the transmission of each segment of the message string. Scan the following Interfunction Delay bar code, then scan the number of 5ms delays, and the Save bar code using the...

  • Page 105: Chapter 7 - Data Formatting

    Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.

  • Page 106: Other Programming Selections

    from the Programming Chart inside the back cover of this manual. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.) Step 6. Editor Commands Refer to (page 7-3). Scan the symbols that represent the command you want to enter. Step 7.

  • Page 107: Terminal Id Table

    Terminal ID Table Terminal Model(s) Terminal ID PC/AT and compatibles PS2 Keyboard USB SurePOS Handheld Scanner USB SurePOS Tabletop Scanner RS232 True RS485 Serial PC Keyboard Mac Keyboard Japanese Keyboard (PC) HID POS Data Format Editor Commands Send Commands Send all characters F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character.
  • Page 108 The data is output as: 1234567890AB Insert symbology name B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page A-1).

  • Page 109: Move Commands

    Insert bar code length B4 Insert the bar code’s length in the output message, without moving the cursor. The length is expressed as a numeric string and does not include leading zeros. B3 and B4 Example: Insert the symbology name and length Send the symbology name and length before the bar code data from the bar code above.

  • Page 110: Search Commands

    Move the cursor to the beginning F7 Move the cursor to the first character in the input message. Syntax = F7. FE and F7 Example: Manipulate bar codes that begin with a 1 Search for bar codes that begin with a 1. If a bar code matches, move the cursor back to the beginning of the data and send 6 characters followed by a carriage return.
  • Page 111 Search forward for a string B0 Search forward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B0nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B0000454657374 will search forward for the first occurrence of the 4 character string “Test.”...

  • Page 112: Miscellaneous Commands

    Search backward for a non-matching character E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII code.
  • Page 113 0D is the hex value for a CR The data is output as: 1234 5678 Stop replacing characters E5 Terminates character replacement. Syntax = E5. Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position.

  • Page 114: Data Formatter

    If this bar code is read, the next data format, if there is one, will be used on this data. If there is no other format, the format fails and the raw data is output as 1234AB. If this bar code is read: the data is output as: AB1234 ...

  • Page 115: Data Format Non-Match Error Tone

    Data Format Required, Keep Prefix/Suffix Data Format Required, Drop Prefix/Suffix Data Format Non-Match Error Tone When a bar code is encountered that doesn’t match your required data format, the scanner normally generates an error tone. However, you may want to continue scanning bar codes without hearing the error tone. If you scan the Data Format Non-Match Error Tone Off bar code, data that doesn’t conform to your data format is not transmitted, and no error tone will sound.

  • Page 116: Single Scan Data Format Change

    Single Scan Data Format Change You can also switch between data formats for a single scan. The next bar code is scanned using an alternate data format, then reverts to the format you have selected above (either Primary, 1, 2, or 3). For example, you may have set your device to the data format you saved as Data Format 3.

  • Page 117: All Symbologies

    Symbologies This programming section contains the following menu selections. Refer to Chapter 11 for settings and defaults. • All Symbologies • GS1-128 • Airline Code 5 - see Straight 2 of 5 IATA (two-bar start/stop) • Interleaved 2 of 5 •...

  • Page 118: Codabar

    Codabar Codabar On/Off * On Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.”...

  • Page 119: Codabar Concatenation

    Validate Modulo 16 and Transmit Validate Modulo 7 CD, but Don’t Transmit Validate Modulo 7 CD and Transmit Validate CLSI, but Don’t Transmit Validate CLSI and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D”...

  • Page 120: Codabar Message Length

    Concatenation Timeout When searching for bar codes during concatenation, you may wish to set a delay used to find the next bar code. Set the length (in milliseconds) for this delay by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.

  • Page 121: Code 39

    Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Code 39 Check Character...

  • Page 122: Code 32 Pharmaceutical (Paraf)

    Code 39 Redundancy If you are encountering errors when reading Code 39 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.

  • Page 123: Full Ascii

    Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.

  • Page 124: Interleaved 2 Of 5

    Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On NULL Characters Interleaved 2 of 5 requires an even number of characters. When an odd number of characters is present, it is due to NULL characters embedded in the bar code.

  • Page 125: Interleaved 2 Of 5 Message Length

    Validate and Transmit Interleaved 2 of 5 Redundancy If you are encountering errors when reading Interleaved 2 of 5 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.
  • Page 126 When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit, the scanner only reads NEC 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data.

  • Page 127: Code 93

    Code 93 < Default All Code 93 Settings > Code 93 On/Off * On Code 93 Redundancy If you are encountering errors when reading Code 93 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.

  • Page 128: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)

    Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Redundancy If you are encountering errors when reading Straight 2 of 5 Industrial bar codes, you may want to adjust the redundancy count.

  • Page 129: Straight 2 Of 5 Iata (Two-Bar Start/Stop)

    Straight 2 of 5 IATA (two-bar start/stop) Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.

  • Page 130: Matrix 2 Of 5

    Matrix 2 of 5 Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Matrix 2 of 5 bar codes printed with a check character, but will not transmit the check character with the scanned data.

  • Page 131: Code 11

    Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 8-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 11...
  • Page 132 Check Digit Validation When Check Character is set to Validate and Transmit, the scanner will only read Code 11 bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data. Validate and Transmit One Check Digit Validate and Transmit Two...

  • Page 133: Code 128

    Code 128 Code 128 On/Off * On 128 Group Separator Output If you wish to transmit embedded FNC1 characters as group separators (1B hex) with your Code 128 bar code output, scan the On bar code. When Off is scanned, nothing is transmitted for FNC1 characters. Default =Off. * Off Code 128 Redundancy If you are encountering errors when reading Code 128 bar codes, you may want to adjust the redundancy count.

  • Page 134: Code 128 Message Length

    Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 8-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood informa-...
  • Page 135 ISBT 128 Predefined Concatenation Sequences Note: You must enable Code 128 and ISBT 128 to use this feature. The following bar codes are used to select the pre-defined ISBT 128 Concatenation Sequence you wish to use. Once you have selected the concatenation sequence, use ISBT 128 Predefined Concatenation Sequences On/Off to enable this fea- ture.
  • Page 136 Default = Off. * Off Allow Predefined Sequence Require Predefined Sequence ISBT 128 User-Defined Concatenation Sequences Note: You must enable Code 128 and ISBT 128 to use this feature. The following bar codes are used to create a custom ISBT 128 Concatenation Sequence. Select the identifiers you want to transmit in the 1st and 2nd positions, both left and right.
  • Page 137 2nd Left Identifier 1st Right Identifier 2nd Right Identifier ISBT 128 User-Defined Concatenation Sequences On/Off The following selections allow you to enable or require the User-Defined ISBT 128 Concatenation Sequences. If you scan Off, the User-Defined concatenation sequences are disabled. If you scan the Allow User-Defined Sequence code, then the scanner will output only the data combination specified in the User-Defined concatenation sequence you created.
  • Page 138 Transmit Identifiers You may disable the transmission of the ISBT Code 128 data identifiers by scanning Off. When this selection is Off, the first 2 data (ID) characters are removed from the data stream unless the ISBT code contains the Donation Identification Number identifiers.

  • Page 139: Gs1-128

    GS1-128 GS1-128 On/Off * On GS1-128 Application Identifier Parsing This allows a single GS1-128 bar code to be broken into multiple transmissions based on the presence of application iden- tifiers (AI) embedded in the bar code. To use this feature, first enable 128 Group Separator Output (page 8-17).

  • Page 140: Telepen

    GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 8-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Telepen ...

  • Page 141: Upc-A

    Telepen Redundancy If you are encountering errors when reading Telepen bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.
  • Page 142 UPC-A Number System and Check Digit UPC-A sample showing the number system and check digit: Number Check Digit UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
  • Page 143 * 5 Digit Addenda Off UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 8-26. Default = Not Required. Required * Not Required Addenda Timeout...

  • Page 144: Upc-A/Ean-13 With Extended Coupon Code

    UPC-A Redundancy If you are encountering errors when reading UPC-A bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.

  • Page 145: Upc-A Number System 5 Addenda Required

    Require Coupon Code UPC-A Number System 5 Addenda Required This setting programs the scanner to require any combination of a coupon code, a 2 digit addenda, or a 5 digit addenda on UPC-A bar codes that begin with a “5.” The following settings can be programmed: Require Coupon Code/Addenda: All UPC-A bar codes that begin with a “5”...

  • Page 146: Upc-E0

    Require Coupon Code, 2 Digit Addenda, or 5 Digit Addenda Addenda Timeout You can set a time during which the scanner looks for a coupon code. If a coupon code is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A/EAN-13 with Extended Coupon Code UPC-A Number System 4 Addenda...
  • Page 147 UPC-E0 Number System The numeric system digit of a UPC-A symbol is normally transmitted at the beginning of scanned data. When using UPC- E Expand, the unit can be programmed so it will not transmit it. Default = On. * On UPC-E0 Number System and Check Digit UPC-E0 sample showing the number system and check digit: Number...
  • Page 148 UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda.

  • Page 149: Ean/Jan-13

    UPC-E0 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = Off. * Off UPC-E0 Redundancy If you are encountering errors when reading UPC-E0 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.
  • Page 150 * Do not Convert UPC-A EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
  • Page 151 * Not Required EAN-13 Beginning with 2 Addenda Required This setting programs the scanner to require a 2 digit addenda only on EAN-13 bar codes that begin with a “2.” The follow- ing settings can be programmed: Require 2 Digit Addenda: All EAN-13 bar codes that begin with a “2” must have a 2 digit addendum. The EAN-13 bar code with the 2 digit addendum is then transmitted as a single, concatenated bar code.
  • Page 152 EAN-13 Beginning with 378/379 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “378” or “379.” The following settings can be programmed: Require Addenda: All EAN-13 bar codes that begin with a “378”...
  • Page 153 Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “434” or “439.” The following settings can be programmed: Require Addenda: All EAN-13 bar codes that begin with a “434”...
  • Page 154 Default = Don’t Require 2 Digit Addenda. * Don’t Require 2 Digit Addenda Require 2 Digit Addenda EAN-13 Beginning with 978 Addenda Required These settings program the scanner to require a 5 digit addenda only on EAN-13 bar codes that begin with “978.” The fol- lowing settings can be programmed: Require 5 Digit Addenda: All EAN-13 bar codes that begin with “978”...

  • Page 155: Isbn Translate

    Require 5 Digit Addenda Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-13 Addenda Required.

  • Page 156: Issn Translate

    * Off Convert ISBN to 13-Digit When translating EAN-13 codes to the ISBN format, you can convert the bar code to a 13 digit format by scanning the Convert to 13-Digit On bar code below. Default = Convert to 13-Digit Off. Convert to 13-Digit On *Convert to 13-Digit Off ISBN Reformat...

  • Page 157: Ean/Jan-8

    ISSN Reformat When Reformat On is scanned, EAN-13 977 Bookland symbols are translated into their equivalent 8-digit ISSN num- ber format, with hyphens added to the output. For example, 9770123456787 will be transmitted as 0123-456-0. (You must first scan ISSN (page 8-40) before scanning Reformat On.) Default = Reformat Off.
  • Page 158 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda.

  • Page 159: Msi

    EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space. Default = Off. * Off EAN/JAN-8 Redundancy If you are encountering errors when reading EAN/JAN-8 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.
  • Page 160 When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data. * Validate Type 10, but Don’t Transmit Validate Type 10 and Transmit Validate 2 Type 10 Characters,...

  • Page 161: Msi Message Length

    MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 8-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Plessey Code <...

  • Page 162: Plessey Message Length

    Plessey Redundancy If you are encountering errors when reading Plessey bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.

  • Page 163: Gs1 Databar Limited

    redundancy, scan the GS1 DataBar Omnidirectional Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. GS1 DataBar Omnidirectional Redundancy GS1 DataBar Limited <...

  • Page 164: Gs1 Databar Expanded

    GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Redundancy If you are encountering errors when reading GS1 DataBar Expanded bar codes, you may want to adjust the redundancy count.

  • Page 165: Gs1 Emulation

    * Off GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and GS1-128 DataBar and GS1 Composites.

  • Page 166: China Post (Hong Kong 2 Of 5)

    China Post (Hong Kong 2 of 5) China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Redundancy If you are encountering errors when reading China Post (Hong Kong 2 of 5) bar codes, you may want to adjust the redundancy count.

  • Page 167: Keyboard Function Relationships

    Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to page 2-20 enable Control + X (Control + ASCII) Mode. Function Code HEX/ASCII Value Full ASCII (CTRL + X Mode)

  • Page 168: Supported Interface Keys

    Country Codes Denmark Norway Spain Supported Interface Keys IBM AT/XT and PS/2 Apple Mac/iMac ASCII Compatibles, Supported Keys WYSE PC/AT Supported Keys Reserved Reserved Enter (KP) Enter/Numpad Enter Cap Lock CAPS ALT make ALT make ALT break ALT break CTRL make CNTRL make CTRL break CNTRL break...

  • Page 169: Chapter 10 - Utilities

    Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.

  • Page 170: Ezconfig-Scanning Introduction

    7. Using Explorer, go to the c:\windows\temp file. 8. Double click on the Setup.exe file. Follow the screen prompts to install the EZConfig-Scanning program. 9. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfig- Scanning.

  • Page 171: Resetting The Factory Defaults

    If using an Access Point, the linking bar code must be scanned. See Cordless System Operation (Voyager 1202g) beginning on page 3-1 or Cordless System Operation (Voyager 1202g-BF) beginning on page 4-1 for additional information. Serial Programming Commands, beginning on page 11-1 list the factory default settings for each of the commands (indi- cated by an asterisk (*) on the programming pages).
  • Page 172 10 - 4...

  • Page 173: Chapter 11 - Serial Programming Commands

    Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming com- mand, refer to the corresponding programming bar code in this manual.

  • Page 174: Responses

    SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and SubTag fields.

  • Page 175: Serial Trigger Commands

    This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; the Check Character (CK2) is set to 0, or Not Required; concatenation (CCT) is set to 1, or Enabled; the Minimum Message Length (MIN) is set to 2 characters;...

  • Page 176: Menu Commands

    Menu Commands Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Product Default Settings Setting Custom Defaults Set Custom Defaults MNUCDF Resetting the Custom Defaults Activate Custom Defaults DEFALT Programming the Interface Plug and Play Codes Keyboard Wedge: PAP_AT IBM PC AT and Compatibles with CR suffix...
  • Page 177 Page * Indicates default # Indicates a numeric entry Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Bioptic Aux Port PAPMAG NCR Bioptic Aux Port PAPNCR Wincor Nixdorf Terminal PAPWNX...
  • Page 178 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Greek (Latin) KBDCTY63 2-14 Greek (MS) KBDCTY66 2-14 Greek (Polytonic) KBDCTY60 2-14 Hebrew KBDCTY12 2-14 Hungarian (101 key) KBDCTY50 2-14 Hungary KBDCTY19 2-14 Iceland KBDCTY75 2-14 Ireland KBDCTY73 2-14 Italian (142)
  • Page 179 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Tatar KBDCTY85 2-18 Thailand KBDCTY94 2-18 Turkey F KBDCTY27 2-18 Turkey Q KBDCTY24 2-18 Ukrainian KBDCTY76 2-18 United Kingdom KBDCTY7 2-18 United Stated (Dvorak right) KBDCTY89 2-18 United States (Dvorak left) KBDCTY88 2-18...
  • Page 180 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry RS-232 Modifiers RS232 Baud Rate 300 BPS 232BAD0 2-23 600 BPS 232BAD1 2-23 1200 BPS 232BAD2 2-23 2400 BPS 232BAD3 2-23 4800 BPS 232BAD4 2-23 *9600 BPS 232BAD5 2-23 19200 BPS...
  • Page 181 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry RS232 Handshaking *RTS/CTS Off 232CTS0 2-25 Flow Control, No Timeout 232CTS1 2-26 Character-Based Flow Control, No 232CTS7 2-26 Timeout Two-Direction Flow Control 232CTS2 2-26 Flow Control with Timeout 232CTS3 2-26 Character-Based Flow Control with...
  • Page 182 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Scanning While in Base Cradle Scanning in Cradle Off BT_SIC0 *Scanning in Cradle On BT_SIC1 Paging Mode BEPPGE1 BEPPGE0 Paging Pitch Low (*1000) (min 100Hz) BEPPFQ1000 Medium (3250) BEPPFQ3250 High (4200) (min 5000Hz) BEPPFQ4200...
  • Page 183 Reset Base RESET_ 3-19 Reset Scanner :*:RESET_ 3-19 Cordless System Operation (Voyager 1202g-BF) Note: This section applies only to Voyager 1202gt-BF cordless systems. It does not apply to corded scanners. Base Power Communication Indicator :*:BASRED1 :*:BASRED0 Reset Scanner Reset Scanner...
  • Page 184 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Scanner Modes Charge Only Mode :*:BASLNK0 *Charge and Link Mode :*:BASLNK1 Locked Link Mode :*:BASCON0 *Open Link Mode :*:BASCON1 Unlink Scanner BT_RMV Override Locked Scanner BT_RPL1 Out-of-Range Alarm Scanner Alarm Type BT_ORW Scanner Alarm Duration (Range 1 - 3000...
  • Page 185 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry LED Settings Red LED Off LEDFN10 Green LED Off LEDFN20 Red LED On with Good Scan LEDFN11 Green LED On with Good Scan LEDFN21 *Red LED On with Laser LEDFN12 *Red LED On with Laser/Red LED Blinks LEDFN11026...
  • Page 186 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Laser Timeout - Button Hold Out-of-Stand AOSMPT##### (Range 1 - 65525) *5000 ms Laser Timeout - Button Release Out-of- AOSMRT##### Stand (Range 1 - 65525) *0 ms *CodeGate Off In-Stand AISCGD0 CodeGate On In-Stand...
  • Page 187 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Character Deactivation Mode *Off HSTDEN0 5-12 HSTDEN1 5-13 Deactivation Character HSTDCH## 5-13 Reread Delay Short (500 ms) DLYRRD500 5-13 *Medium (750 ms) DLYRRD750 5-13 Long (1000 ms) DLYRRD1000 5-13 Extra Long (2000 ms)
  • Page 188 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Data Formatter Selections Data Format Editor *Default Data Format (None) DFMDF3 Enter Data Format DFMBK3## Clear One Data Format DFMCL3 Clear All Data Formats DFMCA3 Data Formatter Data Formatter Off DFM_EN0 7-10...
  • Page 189 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Codabar Concatenation *Off CBRCCT0 CBRCCT1 Require CBRCCT2 Concatenation Timeout DLYCCT Codabar Redundancy Range (0 - 10) *0 CBRVOT## Codabar Message Length Minimum (1 - 80) *3 CBRMIN## Maximum (1 - 80) *80 CBRMAX## Code 39...
  • Page 190 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry NEC 2 of 5 Check Digit *No Check Char. N25CK20 8-10 Validate, But Don’t N25CK21 8-10 Transmit Validate, and Transmit N25CK22 8-10 NEC 2 of 5 Redundancy Range (0 - 10) *0 N25VOT## 8-10...
  • Page 191 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Code 11 Check Digits Required 1 Check Digit Required C11CK20 8-15 *2 Check Digits Required C11CK21 8-15 Auto Select Check Digits Required C11CK22 8-15 Check Digit Validation Validate and Transmit One Check Digit C11CK23 8-16...
  • Page 192 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry ISBT 128 User-Defined Concatenation *Off ISBUCE0 8-21 Sequences On/Off Allow User-Defined Sequence ISBUCE1 8-21 Require User-Defined Sequence ISBUCE2 8-21 Content Verification *Off ISBXM00 8-21 ISBXM01 8-21 Transmit Identifiers ISBXM10 8-22 ISBXM11...
  • Page 193 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry UPC-A Addenda *Off UPAADS0 8-27 Separator UPAADS1 8-27 UPC-A Redundancy Range (0 - 10) *0 UPAVOT## 8-28 UPC-A/EAN-13 with Extended Coupon *Off CPNENA0 8-28 Code Allow Concatenation CPNENA1 8-28 Require Concatenation...
  • Page 194 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry EAN/JAN-13 Default All EAN/ E13DFT 8-33 JAN Settings E13ENA0 8-30 E13ENA1 8-30 Convert UPC-A to EAN-13 UPC-A Converted to EAN-13 UPAENA0 8-33 *Do not Convert UPC-A UPAENA1 8-33 EAN/JAN-13 Check Digit E13CKX0...
  • Page 195 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry ISBN Translate *Off E13ISB0 8-40 E13ISB1 8-39 Convert to 13-Digit On E13I131 8-40 *Convert to 13-Digit Off E13I130 8-40 Reformat On E13IBR1 8-40 *Reformat Off E13IBR0 8-40 ISSN Translate *Off E13ISS0...
  • Page 196 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Plessey Code Default All PLSDFT 8-45 Plessey Code Settings PLSENA0 8-45 PLSENA1 8-45 Plessey Check Char. *No Check Char. PLSCHK0 8-45 Validate, But Don’t PLSCHK1 8-45 Transmit Validate, PLSCHK2 8-45...
  • Page 197 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry China Post (Hong Kong 2 of 5) Msg. Minimum (1 - 80) *3 CPCMIN## 8-50 Length Maximum (1 - 80) *80 CPCMAX## 8-50 Utilities Add Code I.D. Prefix to All Symbologies (Temporary) PRECA2,BK2995C80! 10-1 Show Software Revision...
  • Page 198 11 - 26...

  • Page 199: Chapter 12 - Product Specifications

    Product Specifications Voyager 1200g Product Specifications Parameter Specification Mechanical Height 3.8 in. (97mm) Length 7.1 in. (180mm) Width 2.6 in. (66mm) Weight 4.41 oz. (125g) Electrical Input Voltage 5V + 5% Operating Power 700mW; 140 mA (typical) @ 5V Standby Power 350mW;...

  • Page 200: Voyager 1202G And Voyager 1202G-Bf Product Specifications

    < 1 mw Embedded Laser Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Maximum Power Output 10 mw Voyager 1202g and Voyager 1202g-BF Product Specifications Parameter Specification Mechanical Height 3.6 in. (92mm) Length 7.1 in. (180mm) Width 2.6 in.

  • Page 201: Ccb00-010Bt Product Specifications

    Parameter Specification 16kV air ESD Sensitivity 9kV contact Scan Performance Pitch, Skew 60°, 60° Scan Pattern Single scan line Scan Angle Horizontal: 30° Scan Speed 100 scan lines per second Print Contrast 10% minimum reflectance difference Decode Capabilities Reads standard 1D and GS1 DataBar symbologies DOF with 3.5 mil resolution at standard range Typical Performance 5 mil Code 39...

  • Page 202: Ccb00-010Bt-01N-Bf Product Specifications

    Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1 Range 33 ft. (10 m) typical (line of sight) Data Rate Up to 3 MBps Temperature Ranges: Operating - Charging 41° F to +104° F (5° C to 40° C) Operating - Non-Charging 32°...

  • Page 203: Ccb00-010Bt/Ccb00-010Bt-01N-Vbf Mounting

    +5V power Keyboard data Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.

  • Page 204: Serial Output

    Receive data - serial data to scanner +5V power Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
  • Page 205 Voyager 1200g Safety Label Locations Laser Output Internal Laser Cautions LASER LIGHT: DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT. LASERSTRAHLUNG: NICHT IN DEN STRAHL BLICKEN. LASER KLASSE 2. LUMIERE LASER: NE PAS REGARDER DANS LE FAISCEAU. APPAREIL A LASER. DE CLASSE 2 630-650nm, 1mW.
  • Page 206 Voyager 1202g/Voyager 1202g-BF Safety Label Locations Laser Output Internal Laser Cautions Laser Safety Information LASER LIGHT: DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT. LASERSTRAHLUNG: NICHT IN DEN STRAHL BLICKEN. LASER KLASSE 2. LUMIERE LASER: NE PAS REGARDER DANS LE FAISCEAU. APPAREIL A LASER.
  • Page 207 CCB00-010BT/CCB00-010BT-01N-BF Safety Label Locations Item Number, Compliance Serial Markings Number, and information Compliance Markings information 12 - 9...
  • Page 208 12 - 10...

  • Page 209: Chapter 13 - Maintenance And Troubleshooting

    The interface cable is designed to be field replaceable. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.

  • Page 210: Replacing An Interface Cable In A Corded Scanner

    Replacing an Interface Cable in a Corded Scanner 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the underside of the scanner’s handle. This is the cable release. 4.

  • Page 211: Troubleshooting A Voyager Scanner

    6. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Troubleshooting a Voyager Scanner The scanner automatically performs self-tests whenever you turn it on. If your scanner is not functioning properly, review the following Troubleshooting Guide to try to isolate the problem.

  • Page 212: Troubleshooting A Cordless System

    If you aren’t sure what programming options have been set in the scanner, or if you want the factory default settings restored, refer to Setting Custom Defaults on page 1-6. Troubleshooting a Cordless System Troubleshooting a Base Note: Visit our website (www.honeywellaidc.com) to check for the latest software for the scanner or the base. If your base is not functioning properly, review the following troubleshooting guidelines to try to isolate the problem.

  • Page 213: Chapter 14 - Customer Support

    Limited Warranty Honeywell International Inc. (“HII”) warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
  • Page 214 The duration of the limited warranty for the Voyager 1200g scanner is five (5) years. The duration of the limited warranty for the Voyager 1202g scanner and CCB00-010BT Charge Base is three (3) years. The duration of the limited warranty for the Voyager 1202g-BF scanner and CCB00-010BT-01N-BF Charge Base is three (3) years.

  • Page 215: Symbology Charts

    Refer to Data Editing beginning on page 6-1 and Data Formatting beginning on page 7-1 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...

  • Page 216: Postal Symbologies

    Honeywell Possible modifiers Symbology UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity Postal Symbologies Honeywell Possible modifiers Symbology...

  • Page 217: Lower Ascii Reference Table

    Non-printable ASCII control Keyboard Control + ASCII (CTRL+X) Mode characters Windows Mode Control + X Mode On (KBDCAS2) Char Control + X Mode Off (KBDCAS0) CTRL + X CTRL + X function NP Enter CTRL+ A Select all Caps Lock CTRL+ B Bold ALT Make...
  • Page 218 Printable Characters (Continued) Character Character Character < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ € Ç 0x48 up arrow ↓ ü 0x50 down arrow → ‚ é 0x4B right arrow ← ƒ â 0x4D left arrow „...
  • Page 219 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code – û 0x41 — ù 0x42 ˜ ÿ 0x43 ™ Ö 0x44 š Ü 0x57 › ¢ 0x58 œ £ Numeric Keypad + 0x4E ¥ Numeric Keypad - 0x4A ž...
  • Page 220 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Ê ╩ Ë ╦ Ì ╠ Í ═ Î ╬ Ï ╧ Ð ╨ Ñ ╤ Ò ╥ Ó ╙ Ô ╘ Õ ╒ Ö ╓ × ╫ Ø...

  • Page 221: Iso 2022/Iso 646 Character Replacements

    (standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
  • Page 222 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ⎯ ¥ ⎯ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...

  • Page 223: Keyboard Key References

    Keyboard Key References 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
  • Page 224 A - 10...
  • Page 226 Sample Symbols UPC-A 0 123456 7890 Interleaved 2 of 5 1234567890 Code 128 Code 128 EAN-13 9 780330 290951 Code 39 BC321 Codabar A13579B Code 93 123456-9$ Straight 2 of 5 Industrial 123456...
  • Page 227 Matrix 2 of 5 6543210 GS1 DataBar (01)00123456789012...
  • Page 228 Programming Chart...

  • Page 229: Programming Chart

    Programming Chart Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
  • Page 230 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 VG1200-UG Rev F 5/15...

This manual is also suitable for:

Voyager 1200gVoyager 1202g

Table of Contents