Page 3
Valid for machines as of serial number: 70100000 Storage site for the technical documents: Saint-Gobain Abrasives 190, Bd. J. F. Kennedy 4930 BASCHARAGE, LUXEMBOURG This declaration of conformity loses its validity when the product is converted or modified without agreement.
VERS.2017.06.12 C51_MAN_EN 1 BASIC SAFETY INSTRUCTIONS The C51 is exclusively designed for the cutting of floors made of asphalt, green and cured concrete (reinforced or not) as well as of industrial cement. Uses other than the manufacturer's instructions shall be considered as contravening the regulations.
VERS.2017.06.12 C51_MAN_EN Rotation of the wheel in the indicated Rotation of the wheel in the indicated direction lowers the blade direction raises the blade Never move the machine with the blade Rotation direction of the blade running idle. Emergency Stop 1.2 Machine plate Important data can be found on the following plate located on the machine: Machine Model...
VERS.2017.06.12 C51_MAN_EN 1.3 Safety instructions for particular operating phases Before commencing work Before commencing work, make yourself familiar with the working environment at the place of use. The working environment includes: obstacles in the area of work and manoeuvre, the firmness of the floor, necessary protection at the site relating to public thoroughfares and the availability of help in the event of accidents.
Any modification, which could lead to a change in the original characteristics of the machine, may be done only by Saint-Gobain Abrasives S.A. who shall confirm that the machine is still in conformity with the safety regulations. Saint-Gobain Abrasives S.A. keeps the right of making technical or design modification without prior notification.
Page 10
VERS.2017.06.12 C51_MAN_EN Made of jig welded open profile steel, the C51 is stable but at the same time, easily transportable. The one-piece blade guard (1) fully protects the operator and his working environment. It is firmly fixed to the main frame. A handle on the top of the blade guard facilitates its removal when changing blades.
VERS.2017.06.12 C51_MAN_EN 2.3 Technical data Engine Honda GX200, 4 strokes, 1 cylinder, 6,5HP (4,8kW) Filter Dual Filter Fuel Regular unleaded Honda 4-Stroke, or equivalent high detergent, premium quality motor oil certified to meet or exceed U.S. automobile manufacturer’s requirement for service classification SG, SF. (SG, SF designated on the oil container).
VERS.2017.06.12 C51_MAN_EN Statement regarding the vibration emission Declared value of vibration emission following EN 12096. Machine Measured value of vibration Uncertainty K Tool used Model / code emission at m/s Model / code C 51 P6.5 HONDA 6.02 Duo Extrême 70184683534 ...
VERS.2017.06.12 C51_MAN_EN Statement regarding noise emission Declared value of noise emission following EN ISO 11201 and NF EN ISO 3744. Machine Sound Uncertainty K Sound power Uncertainty K Model / code Pressure level (Sound level (Sound power level Pressure level EN ISO 11201 NF EN ISO 3744 NF EN ISO 3744)
VERS.2017.06.12 C51_MAN_EN ASSEMBLY AND COMMISSIONING Before beginning the work with the C51, you have to assemble some parts. 3.1 Assembly Secure the operator’s handle in a comfortable user position by using the locking nut. 3.2 Tool assembly Only use NORTON blades with the C51. A blade with a maximum diameter of 350 mm can be fitted in the C51.
VERS.2017.06.12 C51_MAN_EN 3.4 Starting the machine Make sure the blade is raised clear up the ground before starting the machine. Turn the fuel valve to the ON position. Move the choke lever to the CLOSED position. NOTE: do not use the choke if the engine is warm or the air temperature is high.
VERS.2017.06.12 C51_MAN_EN 4 TRANSPORT AND STORING Take the following measures in order to transport and store the C51 securely. 4.1 Securing for transport Before transporting the machine: Remove the blade. Empty the water tank. Lower the handle in its fixing tube and secure it using the locking nut. ...
VERS.2017.06.12 C51_MAN_EN 5 OPERATING THE C51 5.1 Site of work Before you start working, please check the following points: Remove from the site anything, which might hinder the working procedure. Make sure the site is sufficiently well lit. ...
Page 18
VERS.2017.06.12 C51_MAN_EN push the machine forward with steady and gentle pressure and follow the line with the pointer. The feed speed must be adjusted depending on the material being cut, and depth of cut. At the finish of the cut, raise the blade out of the cut by turning the hand wheel clockwise, shut-off the water and switch off the engine.
VERS.2017.06.12 C51_MAN_EN 6 MAINTENANCE AND SERVICE ATTENTION : to perform maintenance on the machine, always switch it off. Always wear a face mask and safety goggles while performing the maintenance of machine. 6.1 Maintenance of the machine To ensure a long-term quality from the cutting with the C51, please follow the maintenance plan below: Regular service period Perform...
VERS.2017.06.12 C51_MAN_EN 6.2 Maintenance of the engine Regular service period Perform at every indicated month or operating hour interval, whichever comes first Check level Engine oil Change Check Air cleaner filter Clean Fuel strainer cup Clean Spark plug Check-Clean Fuel line Check (Replace if necessary) Every 2 years...
Page 21
VERS.2017.06.12 C51_MAN_EN Air cleaner The C51 has a dual type filter. To service the air cleaner filter, follow these instructions: Remove the nut, air cleaner cover and wing nut. Remove the pre air cleaner elements and separate them. ...
Page 22
VERS.2017.06.12 C51_MAN_EN Spark plug To service the spark plug, follow these instructions: Visually inspect spark plug. Discard the plug if the insulator is cracked or chipped. Remove carbon or other deposits with a stiff wire brush. Measure the plug gap with a wire-type feeler gauge.
VERS.2017.06.12 C51_MAN_EN 7 FAULTS: CAUSES AND CURES 7.1 Fault-finding procedures Should any fault occur during the use of the machine, turn it off. Let only qualified staff make any intervention other than the one described in the previous section. 7.2 Trouble-shooting guide Trouble Possible source Resolution...
In the case of a warranty is claim, the part must always be returned for evaluation. Spare parts for the engine can be ordered with the manufacturer of the engine or with their dealer, which is often quicker and cheaper. This machine has been manufactured by Saint-Gobain Abrasives S.A. 190, Bd J.F.Kennedy L- 4930 BASCHARAGE Grand-Duché...
Page 25
VERS.2017.06.12 C51_MAN_EN Guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well:...