Page 3
Valid for machines with serial number from: 1609XXXXX Storage location of the technical documents: Saint-Gobain Abrasives 190, Bd. J. F. Kennedy 4930 BASCHARAGE, LUXEMBOURG This declaration of conformity loses its validity when the product is converted or modified without agreement.
VERS.2017.03.08 CST ALU_MTS_MAN_EN 1 BASIC SAFETY INSTRUCTIONS The CST is exclusively designed for the cutting of abrasive materials with NORTON diamond blades, mainly on construction sites. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufacturer shall not be held responsible for any resulting damage. Any risk shall be borne entirely by the user.
VERS.2017.03.08 CST ALU_MTS_MAN_EN 1.2 Machine plate Important data can be found on the following plate located on the machine: Machine code Year of production Bore diameter Machine model Weight Max. blade diameter Serial number Machine type Safety standard Blade speed Power 1.3 Safety instructions for particular operating phases Before commencing work...
2 MACHINE DESCRIPTION Any modification, which could lead to a change in the original characteristics of the machine, may be done only by Saint-Gobain Abrasives who shall confirm that the machine is still in conformity with the safety regulations. 2.1 Short description CST type Masonry saw is a machine with fixed table and mobile head.
Page 9
VERS.2017.03.08 CST ALU_MTS_MAN_EN Frame (1) Jig-welded steel construction, the frame is robust and resistant. The side posts of the machine ensure that the rail is parallel to the table. The rails (4) assembly can also be tilted to 45º to make bevel cuts.
VERS.2017.03.08 CST ALU_MTS_MAN_EN 2.4 Technical data Code CST 100 ALU CST 120 ALU CST 100 ALU CST 120 ALU Description 230V 230V 115V 115V Power 2,2 kW 1.8 kW Voltage 230V 1~ 115V 1~ Motor protection IP 54 Sound pressure level 73,5 dB (A) (refer toISO EN 11201) Sound energy level 88,5 dB (A) (refer to ISO EN 3744)
VERS.2017.03.08 CST ALU_MTS_MAN_EN 2.5 Statement regarding the vibration emission Declared value of vibration emission following EN 12096. Measured value of Tool used Uncertainty K Machines vibration emission Model / code Modèle / code at m/s CST 100 ALU 230V / 70184601937 CST 100 ALU 115V / 70184602124 Duo Granit <2.5...
VERS.2017.03.08 CST ALU_MTS_MAN_EN Statement regarding noise emission Declared value of noise emission following EN ISO 11201 and NF EN ISO 3744. Sound Uncertainty K Uncertainty K Sound power Pressure (Sound (Sound power Machine level L level L Pressure level level L Modèle / code NF EN ISO 3744 EN ISO...
VERS.2017.03.08 CST ALU_MTS_MAN_EN 3 ASSEMBLY ANDCOMMISSIONING The machine is delivered fully equipped. It is ready for operation when you mount the diamond blade, the handles and the conveyor cart and after you connect to the appropriate power supply. 3.1 Tool assembly Only NORTON blades should be used.
VERS.2017.03.08 CST ALU_MTS_MAN_EN 400V Motor: Direction of rotation The direction of rotation is indicated on the blade guard. If the direction of rotation does not correspond to the direction shown by the arrow, then reverse the motor polarity by turning the phase inverter inside the male plug with a screwdriver.
VERS.2017.03.08 CST ALU_MTS_MAN_EN 4 TRANSPORT AND STOCKING 4.1 Securing for transport Before transporting or lifting the machine, always remove the blade and empty the water pan. Also lock the cutting head on the rail. To do so, move the head in the middle of the rail and tighten the knob screw until the cutting head is secured on the rail.
VERS.2017.03.08 CST ALU_MTS_MAN_EN 5 OPERATING THE MACHINE In this part, you will find some safety tips to use the machine. 5.1 Site of work 5.1.1 Sitting the machine Remove from the site anything, which might hinder the working procedure! ...
VERS.2017.03.08 CST ALU_MTS_MAN_EN 5.3 General advice for the cutting The CST is designed to cut materials with maximal dimensions of : CST 120 ALU CST 120 ALU CST 100 ALU CST 100 ALU Modèle 115V 230V 115V 230V Ø disque 350 mm 350 mm 350 mm...
VERS.2017.03.08 CST ALU_MTS_MAN_EN 6 MAINTENANCE AND SERVICING To ensure a long-term quality from the cutting with the CST, please follow the maintenance plan below: Visual control (general aspect, watertightness) Whole machine Clean Flange and blade fixing devices Clean Motor cooling fans Clean Water pump Clean...
VERS.2017.03.08 CST ALU_MTS_MAN_EN 7 FAULTS: CAUSES AND CURES 7.1 Fault-finding procedures Should any fault occur during the use of the machine, turn it off, and isolate it from the electrical supply. Any works dealing with the electrical system or supply of the machine can only be carried out by a qualified electrician.
In the case of a warranty claim, the part must always be returned for evaluation. Spare parts for the motor can be ordered with the manufacturer of the motor or with their dealer, which is often quicker and cheaper. This machine has been manufactured by Saint-Gobain Abrasives S.A. 190, Bd J.F.Kennedy L- 4930 BASCHARAGE Grand-Duché...
Page 23
VERS.2017.03.08 CST ALU_MTS_MAN_EN Guarantee can be claimed and technical support obtained from your local distributor where machines, spare parts and consumables can be ordered as well:...