Page 1 MODEL IFP-2000/ RPS-2000 Analog/Addressable Fire System Installation and Part Number 151430 Rev A Operations Manual firealarmresources.com...
Page 2 firealarmresources.com...
Page 3 Installation Procedure Adherence to the following will aid in problem-free installation with long-term reliability: Installation Precautions - Adherence to the following will aid in problem-free installation with long-term reliability: WARNING - Several different sources of power can be connected to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while the unit is energized.
Page 4 FACP operation and reliability depend upon proper installation. While installing a fire alarm system may make lower insurance rates possible, it is not a substitute for fire insurance! An automatic fire alarm system - typically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control with remote notification capability - can provide early warning of a developing fire.
Page 5: Table Of Contents
Contents Contents Section 1 Introduction .............................. 1-1 Overview of Basic System ........................1-1 1.1.1 Hardware Features ..........................1-1 1.1.2 Network System Hardware Features ....................1-2 1.1.3 Software Features ..........................1-2 About this Manual ............................ 1-3 1.2.1 Terms Used in this Manual ....................... 1-3 Compatible Products ..........................
Page 6 Contents AC Connection ............................4-2 Battery Connection ..........................4-3 4.3.1 Battery Accessory Cabinets ......................4-4 4.3.1.1 Installing the RBB or AB-55 Accessory Cabinet and Batteries ..........4-4 SBUS Wiring ............................4-7 4.4.1 Calculating Wiring distance for SBUS modules ................4-7 4.4.2 Wiring Configurations ........................
Page 7 Contents 4.15.4.1 Using the 5220 Module ......................4-46 4.15.4.2 Using the 7644 Module ......................4-47 4.15.5 Transmitter Activated by Dry Contacts ..................4-48 Section 5 Networking ..............................5-1 Network System Hardware Features ......................5-1 5.1.1 Networked Sites ..........................5-1 5.1.2 Wiring Options to Connect Networked Panels ................. 5-1 Model RPS-2000 ............................
Page 8 Contents List of IDP SLC Devices ......................... 7-1 Maximum Number of Devices ......................... 7-2 Wiring Requirements for SLC Devices ....................7-2 7.3.1 Wiring 5815XL in Style 4 (Class B) Configuration ................. 7-2 7.3.2 Wiring 5815XL in Style 6 & 7 (Class A) Configuration ..............7-4 Wiring IDP SLC Detectors ........................
Page 9 Contents 9.4.1.2 Edit Group Properties ......................9-11 9.4.2 Add Group ............................9-12 9.4.3 Delete Group ........................... 9-13 9.4.4 View Group Points .......................... 9-14 Point ............................... 9-15 9.5.1 Point Programming For 5815XL Module ..................9-15 9.5.2 Point Programming For Internal or External Power Module (RPS-1000) ........9-18 9.5.3 Point Programming For 5880, and 5865 Modules ................
Page 10 Contents 10.3.1 Main Menu Overview ........................10-4 10.3.2 Using the Menus ..........................10-5 10.4 Basic Operation ............................10-5 10.4.1 Setting Time and Date ........................10-5 10.4.2 Disable / Enable a Point ........................10-5 10.4.3 Disable / Enable NACs by Group ....................10-5 10.4.4 View Event History ........................
Page 11 Contents 12.3.4 Earth Fault Resistance ........................12-6 Section 13 Installation Records ........................13-1 13.1 Detector and Module Point Record ......................13-1 13.2 Conventional Output Point Record ......................13-6 Appendix A Compatible Devices ........................14-1 Appendix B Special Characters Lists ......................B-1 Silent Knight Fire Product Warranty and Return Policy 151430 firealarmresources.com...
Page 12 IFP-2000 Installation Manual viii firealarmresources.com...
Page 13: Introduction
Introduction Section 1 Introduction The IFP-2000 Fire Alarm Control/Communicator is an analog addressable fire control system that meets the requirements of UL 864. The RPS-2000 is used in a networked system where there is at least one IFP-2000 in the system. The RPS-2000 is the same as the IFP-2000 without the display.
Page 14: Network System Hardware Features
IFP-2000 Installation Manual • Supports conventional 2-wire & 4-wire detectors using the 8 Flexput™ circuits or SLC zone modules. • 999 software zones, 999 output groups. • Add 4 notification/auxiliary power circuits with each 5496 Intelligent Power Module. • Add 6 Flexput™ circuits with each RPS-1000 Remote Power Supply. •...
Page 15: About This Manual
Introduction About this Manual This manual is intended to be a complete reference for all installation and operation tasks for the IFP-2000 and RPS-2000. Please let us know if the manual does not meet your needs in any way. We value your feedback! 1.2.1 Terms Used in this Manual The following terminology is used with the above mentioned control panels:...
Page 16: Compatible Products
IFP-2000 Installation Manual Compatible Products Table 1-1 lists the products available from Silent Knight for use with the IFP-2000. Table 1-2: IFP-2000 Compatible Products Type of Model Description Device See Section 7.1 for a list of compatible devices. Addressable SLC Devices 5815XL SLC Expander Each 5815XL allows up to 159 IPD sensors and 159 IDP modules to be added to the system.
Page 17: How To Contact Silent Knight
Introduction The following modems have been tested by Silent Knight for compatibility with the Silent Knight Software Suite software packages: Table 1-3: Compatible Modems Manufacturer Model US Robotics 28.8 LifeStyle Motorola 28.8, 3400 series Premier 33.6 MultiTech MT19321ZDX How to Contact Silent Knight If you have a question or encounter a problem not covered in this manual, contact Silent Knight Technical Support at 800-328-0103 or 763-493-6455.
Page 18 IFP-2000 Installation Manual Limitations of Fire Alarm Systems Manufacturer recommends that smoke and/or heat detectors be located throughout a protected premise following the recommendations of the current edition of the National Fire Protection Association Standard 72 (NFPA 72), manufacturer’s recommendations, State and local codes, and the recommendations contained in Guide for the Proper Use of System Smoke Detectors, which is made available at no charge to all installing dealers.
Page 19 Introduction heat on their sensors increases at a predetermined rate or reaches a predetermined level. Heat detectors are designed to protect property, not life. • Warning devices (including horns, sirens, and bells) may not alert people or wake up sleepers who are located on the other side of closed or partially open doors. A warning device that activates on a different floor or level of a dwelling or structure is less likely to awaken or alert people.
Page 20 IFP-2000 Installation Manual Requirements and recommendations for proper use of fire alarm systems in- cluding smoke detectors and other fire alarm devices: Early fire detection is best achieved by the installation and maintenance of fire detection equipment in all rooms and areas of the house or building in accordance with the requirements and recommendations of the current edition of the National Fire Protection Association Standard 72, National Fire Alarm Code (NFPA 72), the manufacturer’s recommendations, State and local codes and the recommendations contained in Guide for the Proper Use of...
Page 21 Introduction SURVIVABILITY: Per the National Fire Alarm Code, NFPA 72, all circuits necessary for the operation of the notification appliances shall be protected until they enter the evacuation signaling zone that they serve. Any of the following methods shall be considered acceptable as meeting these requirements: 1) A 2-hour rated cable or cable system 2) A 2-hour rated enclosure...
Page 22 IFP-2000 Installation Manual 1-10 151430 firealarmresources.com...
Page 23: Agency Listings, Approvals, And Requirements
Agency Listings, Approvals, and Requirements Section 2 Agency Listings, Approvals, and Requirements Federal Communications Commission (FCC) 1. The following information must be provided to the telephone company before the IFP- 2000 can be connected to the phone lines: Manufacturer: Silent Knight Model Number: IFP-2000 and IFP-2000HV FCC registration number:...
Page 24: Underwriters Laboratories (Ul)
IFP-2000 Installation Manual This product cannot be adjusted or repaired in the field. It must be returned to the factory for service. This equipment is not designed for use with party line service. Connection to party line service is subject to state tariffs. You may contact the state public utility commission, public service commission or corporation commission for information.
Page 25: Requirements For Central Station Fire Alarm Systems
Agency Listings, Approvals, and Requirements Restricted Options: • The loss of AC signal is defaulted to 3 hours however the system allows settings from 0 - 30 hours. For UL certified installations this number must be set from 1 to 3 hours. •...
Page 26 IFP-2000 Installation Manual 151430 firealarmresources.com...
Page 27: Before You Begin Installing
Before You Begin Installing Section 3 Before You Begin Installing This section of the manual is intended to help you plan your tasks to facilitate a smooth installation. Please read this section thoroughly, especially if you are installing a IFP-2000 or RPS-2000 panel for the first time.
Page 28: Electrical Specifications
IFP-2000 Installation Manual Electrical Specifications Earth Ground Terminal Label Description Rating Faults Voltage Current 5A for the IFP-2000, 120/240 VAC, AC input (hot) 50/60 Hz 2.5A for the IFP-2000HV Earth ground 5A for the IFP-2000, 120/240 VAC, AC input (neutral) 50/60 Hz 2.5A for the IFP-2000HV 3.0 Amp Notification and...
Page 29 Before You Begin Installing Earth Ground Terminal Label Description Rating Faults Voltage Current Used for Class A installations 0Ω SBUS1 IN SBUS communication 5 VDC 100 mA SBUS2 OUT 0Ω SBUS power 24 VDC 1.0 A SBUS2 IN Used for Class A installations 0Ω...
Page 30: Wiring Specifications
IFP-2000 Installation Manual Wiring Specifications Induced noise (transfer of electrical energy from one wire to another) can interfere with telephone communication or cause false alarms. To avoid induced noise, follow these guidelines: • Isolate input wiring from high current output and power wiring. Do not pull one multi- conductor cable for the entire panel.
Page 31 Before You Begin Installing Figure 3-1 Wire Routing Example 151430 firealarmresources.com...
Page 32: Board Assembly Diagram
IFP-2000 Installation Manual Board Assembly Diagram Trouble Relay On-board Annunciator To AC Ethernet Port In/Out Phone lines (non-power limited) Network Repeater Programming Port Battery Chassis Connections Mounting Nuts Figure 3-2 Model IFP-2000 Assembly Figure 3-2 shows the circuit boards, metal housing and annunciator that attach the IFP-2000 assembly to the cabinet.
Page 33: Calculating Current Draw And Standby Battery
Before You Begin Installing Calculating Current Draw and Standby Battery This section is for helping you determine the current draw and standby battery needs for your installation. 3.6.1 Current Draw Worksheet Requirements The following steps must be taken when determining IFP-2000 current draw and standby battery requirements.
Page 34 IFP-2000 Installation Manual Table 3-1: Current Draw Worksheet for IDP SLC Devices Standby Alarm Device # of Devices Current per Device Current Current For each device use this formula: This column This column Current per number of devices. Standby: 290 mA 290 mA Fire Panel (Current draw from battery)
Page 35 Before You Begin Installing Standby Alarm Device # of Devices Current per Device Current Current Accessories Modules Standby/Alarm: 55 mA 5815XL SLC Expander (63 max) Standby: 25 mA RA-2000 Remote Fire Alarm (63 max) Annunciator Alarm: 50 mA 5824 Serial/Parallel Module (2 max.) Standby/Alarm: 45 mA...
Page 36: Maximum Battery Standby Load
IFP-2000 Installation Manual 1. Total does not include isolator devices or accessory bases. 2. If using 24 VDC aux power only. No standby or alarm current for battery calculation if using 24 VAC, 120 VAC or 240 VAC. 3. If using door holders, you do not need to consider door holder current for alarm/battery standby, because power is removed during that time.
Page 37 Before You Begin Installing order they are listed here. Important: Connect and address SLC devices before running JumpStart AutoProgramming. See Sec. Task (for more info.) Main Panel Hardware Installation Mount the control panel cabinet. Connect AC. Connect phone lines. 4.12 Install 5815XL SLC expander modules (if needed).
Page 38 IFP-2000 Installation Manual See Sec. Task (for more info.) JumpStart AutoProgramming automatically selects some options for SLC devices (see “JumpStart AutoProgramming” section of this chart). You can change options selected by JumpStart AutoProgramming, if necessary and further customize input point options. Program type of switch (manual pull, fire drill, and so on), if necessary.
Page 39: Control Panel Installation
Control Panel Installation Section 4 Control Panel Installation Caution! To avoid the risk of electrical shock and damage to the unit, power should be OFF at the control panel while installing or servicing. Mounting the Control Panel Cabinet Read the environmental specifications in Section 3.2 before mounting the control panel cabinet.
Page 40: Ac Connection
IFP-2000 Installation Manual AC Connection At installation, connect the AC terminals to the power source as shown in Figure 4-1 or Figure 4-2. It may be necessary for a professional electrician to make this connection. The AC terminals are rated at 120 VAC, 50 or 60 Hz, 5A (for the IFP-2000) or 240 VAC 50 or 60 Hz, 2.5A (for the IFP-2000HV).
Page 41: Battery Connection
Control Panel Installation Battery Connection The control panel battery charge capacity is 17 to 55 AH. Use 12V batteries of the same AH rating. Determine the correct AH rating as per your standby load calculation (see Section 3.6). Wire batteries in series to produce a 24-volt equivalent. Do not parallel batteries to increase the AH rating.
Page 42: Battery Accessory Cabinets
IFP-2000 Installation Manual 4.3.1 Battery Accessory Cabinets The Model RBB or AB-55 Accessory cabinets can be used when your required to use backup batteries that are too large to fit into the main control panel cabinet. The RBB cabinet holds batteries up to the 35 AH size. The RBB dimensions are 16" W x 10" H x 6"...
Page 43 Control Panel Installation 2. Connect the main control panel battery cables to the battery cable extenders as shown in Figure 4-5. Figure 4-5 Splicing Control panel Battery Cable to RBB or AB-55 Battery Cable Extenders 3. Run extended battery cable from control panel cabinet through conduit to RBB or AB-55 cabinet.
Page 44 IFP-2000 Installation Manual 6. Align the cover plate mounting keyhole over the cover mounting screws. See Figure 4-7. Cover Plate Mounting Keyholes Figure 4-7 Cover Plate Mounting Keyholes and Cover Mounting Screws Alignment 7. Slide the cover into place and tighten the cover mounting screws. See Figure 4-7 151430 firealarmresources.com...
Page 45: Sbus Wiring
Control Panel Installation SBUS Wiring This section contains information on calculating SBUS wire distances and the types of wiring configurations (Class A and B). 4.4.1 Calculating Wiring distance for SBUS modules The IFP-2000 panel has two SBUS circuits which can support up to 1.0A of module load per SBUS circuit.
Page 46 IFP-2000 Installation Manual These cases are marked in the chart with an asterisk (*). Maximum length can never be more than 6,000 feet, regardless of gauge used. (The formula used to generate this chart is shown in the note below). Table 4-1: Wire Distances Per Wire Gauge Using Copper Wire Wiring Distance: SBUS Modules to Panel Total Worst Case...
Page 47: Wiring Configurations
Control Panel Installation Wiring Distance calculation example: Suppose a system is configured with the following SBUS modules: 2 - Module RA-2000 Fire Annunciator 1 - RPS-1000 Intelligent Power Expander 1 - 5865 LED Fire Annunciator 1 - 5824 Serial/Parallel Interface Module The total worst case current is calculated as follows: RA-2000 Current Draw = 2 x .120 amps...
Page 48 IFP-2000 Installation Manual Class B configuration. SBUS 2 wiring configurations are the same as SBUS1. Caution For proper system supervision do not use looped wire under terminals marked A, B, +, and - of the SBUS device connectors. Break wire runs to provide supervision of connections.
Page 49: Configuring Sbus Modules
Control Panel Installation Configuring SBUS Modules This section describes how to configure any system hardware modules that have been added to the system. 4.5.1 Assigning SBUS Module IDs SBUS devices on a panel are addressed from 1 to 63 and are connected to either SBUS 1 or SBUS 2.
Page 50: Sbus Bandwidth Considerations
IFP-2000 Installation Manual 4.5.2 SBUS Bandwidth Considerations Each SBUS device generates a certain amount of traffic on the SBUS. Generally, the amount of traffic generated depends on the type of SBUS device. To help you figure out the SBUS bandwidth usage of a given collection of devices, we have created a tool available on the Farenhyt website (www.farenhyt.com).
Page 51: Ra-2000 Remote Annunciator Installation
Control Panel Installation RA-2000 Remote Annunciator Installation The optional Model RA-2000 Remote Annunciator, shown in Figure 4-11, performs the same functions as the on-board annunciator. Operation is identical. The RA-2000 can be surface or flush mounted. Figure 4-11 Model RA-2000 Remote Annunciator, Front View RA-2000 installation involves the following steps: 1.
Page 52: Mounting The Ra-2000
IFP-2000 Installation Manual 4.6.1 Mounting the RA-2000 This section of the manual describes mounting the remote annunciator. The annunciator can be flush- or surface-mounted. 4.6.1.1 Flush Mounting This section of the manual describes flush mounting. Follow these steps to flush mount the RA-2000 1.
Page 53 Control Panel Installation 2. Remove knockout holes as needed for wires. See Figure 4-13 for backbox knockout loca- tions Wire Knockouts Wire Knockouts Wire Knockouts Figure 4-13 Back Box Knockout Locations 3. Wire the Annunciator board to the main control panel. See Figure 4-9. 4.
Page 54: Surface Mounting
IFP-2000 Installation Manual 4.6.1.2 Surface Mounting The Model RA-100TR trim ring kit is available for use when surface mounting the RA-2000. 1. Remove the desired knock out. See Figure 4-13. 2. To properly mount the back box, insert a single screw into the key shaped mounting hole. Do not tighten all the way.
Page 55: Model Ra-2000 Connection To The Panel
Control Panel Installation 6. After the annunciator wiring to the panel has been completed (described in Section 4.6.2), replace the electronic assembly in the back box. Place the bezel over the back box and tighten the set screws on the bezel. 4.6.2 Model RA-2000 Connection to the Panel Connect the RA-2000 to the panel as shown in Figure 4-17...
Page 56: 5815Xl Installation
IFP-2000 Installation Manual 5815XL Installation The 5815XL SLC expander lets you add additional addressable devices. The maximum number of SLC devices per panel is 636. The number of 5815XL’s is limited by the maximum number of SBUS devices.) To install the 5815XL: 1.
Page 57: 5815Xl Connection To The Panel
Control Panel Installation 4.7.1 5815XL Connection to the Panel Connect the 5815XL to the control panel as shown in Figure 4-19. After the 5815XL is connected to the panel, it must be added to the system. This programming step is described in Section 9.2.2.
Page 58: 5824 Serial/Parallel Interface Module Installation
IFP-2000 Installation Manual 5824 Serial/Parallel Interface Module Installation The 5824 serial/parallel interface module allows you to connect a printer to the panel, so you can print a real-time log of system events. Instructions for installing the 5824 appear below. The 5824 is for ancillary use only. 5824 installation involves the following steps: 1.
Page 59: Selecting 5824 Options
Control Panel Installation Model 5824 (with housing) To Parallel Printer To Serial Printer Figure 4-21 Printer Connection 4.8.1 Selecting 5824 Options Configuring the 5824 includes the following steps: • Add the module to the system. JumpStart will add the module automatically (see Section 8.1).
Page 60 IFP-2000 Installation Manual Printer and Output Port Options 1. From the Main Menu, select for Panel Programming. 2. Select for Module. 3. Select for Edit Module. 4. From the list that displays, select the 5824 module you want to configure. 5.
Page 61: 5880 Led I/O Module
Control Panel Installation 5880 LED I/O Module The 5880 is an LED driver board that can be used in a wide variety of applications, including as an interface with most customized floor plan annunciator boards. The 5880 can drive up to 40 LEDs and has one PZT controller.
Page 62: Facp Connection
IFP-2000 Installation Manual 4.9.2 FACP Connection The 5880 connects to the panel via the SBUS. Make connections as shown in Figure 4-24. After the 5880 is connected to the panel, it must be added to the system. This programming step is described in Section 9.2.2. Figure 4-24 5880 Connection to Main Control Panel Assembly 4-24 151430...
Page 63: Led Wiring
Control Panel Installation 4.9.3 LED Wiring There are four 12-pin connectors on the 5880 board for connecting LEDs. Each LED gets its power from Pin 11. Internal resistors are sized so that there is approximately 10 mA of current for each LED, no series resistors are required. LED outputs can be mapped to output circuits. See Section 9.5.3 for programming details.
Page 64: Dry Contact Wiring
IFP-2000 Installation Manual 4.9.4 Dry Contact Wiring The 8 input circuits on the 5880 board are for monitoring switch inputs-any type of switch supported by the control panel can be used with the 5880. For example, you can use a 5880 to monitor pull stations, water flow, tamper, reset, or silence switches.
Page 65: 5865-3 / 5865-4 Led Annunciator Installation
Control Panel Installation 4.10 5865-3 / 5865-4 LED Annunciator Installation The 5865-3 and 5865-4 are LED annunciators. The 5865-4 has 30 mappable LEDs, remote silence and reset key switches, and a general system trouble LED. The 5865-3 has 30 mappable LEDs only. These are arranged as 15 pairs of red (typically used for alarm) and yellow (typically used for trouble) LEDs.
Page 66: Facp Connection
IFP-2000 Installation Manual 4.10.1 FACP Connection The 5865 connects to the panel via the SBUS. Make connections as shown in Figure 4-28. After the 5865 is connected to the panel, it must be added to the system. This programming step is described in Section 9.2.2. Figure 4-28 5865 Connection to the FACP 4-28 151430...
Page 67: 5865 Mounting
Control Panel Installation 4.10.2 5865 Mounting Mount the 5865-4 to a standard 4-gang electrical box. Mount the 5865-3 to a standard 3-gang electrical box. In Figure 4-29, the 5865-4 attached to a 4-gang box is used as an example. Figure 4-29 5865 Mounting Example The 5865 ships with a set of zone description labels that can be inserted into the 5865 board assembly.
Page 68: Vip Module Installation
IFP-2000 Installation Manual 4.11 Vip Module Installation For Installation of the VIP-50, VIP-VCM and VIP-RM2000 modules refer to the VIP-Series Installation manual P/N 151286. Note: When using these modules on a network of panels, the VBUS must not span panels. A VBUS can only be connected between modules on the same panel.
Page 69: Conventional Notification Appliance
Control Panel Installation ™ 4.13 Flexputs I/O Circuits The eight Flexput™ circuits are an innovative and versatile feature of the control panel. They can be used as: Class A or B notification circuits, Class A or B initiation circuits (either 2 or 4 wire detectors), or as auxiliary power (resettable, continuous, or door holder).
Page 70 IFP-2000 Installation Manual 2. Configure the circuit through programming (see Section 9.5)) Alarm Polarity Shown. Notification Wiring Power Limited Supervised UL Listed EOL Model 7628 Regulated 24 VDC 4.7 kΩ 3A per Circuit, 9A max Combined Figure 4-32 Class B Notification Appliance Circuit Wiring Maximum voltage drop per Class B notification circuit is 3V.
Page 71: Class A Notification Wiring
Control Panel Installation 4.13.1.2 Class A Notification Wiring You must use an appliance from the list of compatible appliances in the Appendix at the back of this manual. To install a Class A notification appliance circuit: 1. Wire the Class A notification appliances as shown in Figure 4-33. 2.
Page 72: Conventional Input Switch Circuits
IFP-2000 Installation Manual 4.13.2 Conventional Input Switch Circuits This section of the manual explains how to install conventional initiating devices for Class A (Style D) or Class B (Style B) configurations. 4.13.2.1 Class B Inputs You can connect conventional Class B switches, such as waterflow switches and pull stations, directly to the Flexput circuits of the control panel.
Page 73: Class A Inputs
Control Panel Installation 4.13.2.2 Class A Inputs You can connect conventional Class A switches, such as waterflow switches and pull stations, directly to the Flexput circuits of the control panel. To install a Class A switch: 1. Wire the Class A switch as shown in Figure 4-35. 2.
Page 74: Installing 2-Wire Smoke Detectors
IFP-2000 Installation Manual 4.13.3 Installing 2-Wire Smoke Detectors Any compatible U.L. listed two-wire smoke detector can be used with the control panel (see for list of compatible smoke detectors). Figure 4-36 and Figure 4-37 illustrate how to connect a UL listed 2-wire detector to the control panel. 4.13.3.1 Installing 2-Wire Class B Smoke Detectors To install a Class B two-wire smoke detector, wire as shown in Figure 4-36.
Page 75: Installing 2-Wire Class A Smoke Detector
Control Panel Installation 4.13.3.2 Installing 2-Wire Class A Smoke Detector To install a Class A two-wire smoke detector, wire as shown in Figure 4-37. Supervised Power Limited Note: Flexput circuit 5 and 6 used as an example. Any Flexput point pairing could be used.
Page 76: Installing 4-Wire Smoke Detectors
IFP-2000 Installation Manual 4.13.4 Installing 4-Wire Smoke Detectors Any compatible U.L. listed four-wire smoke detector can be used with the control panel (see for list of compatible smoke detectors). Figure 4-38 and Figure 4-39 illustrate how to connect a UL listed four-wire detector to the control panel. 4.13.4.1 Installing a Class B 4-Wire Smoke Detector Figure 4-38 illustrates how to install a 4-wire Class B smoke detector.
Page 77: Installing 4-Wire Class A Smoke Detectors
Control Panel Installation 4.13.4.2 Installing 4-Wire Class A Smoke Detectors Figure 4-39 illustrates how to install 4-wire Class A detectors. Conventions used for wiring 4-wire Class A loops: 1. Up to two Class A 4-wire loops can be connected to the control panel at once. 2.
Page 78: Auxiliary Power Installation
IFP-2000 Installation Manual 4.13.5 Auxiliary Power Installation Flexput Circuits 1-8 on the control panel can be used as auxiliary power circuits. The three types of auxiliary power available are: • Door Holder (see Section 4.13.5.1) • Constant (see Section 4.13.5.2) •...
Page 79: Constant Power
Control Panel Installation 4.13.5.2 Constant Power Use constant power for applications that require a constant auxiliary power source. Power is always present at constant circuits. You must have backup generator to supply standby power. See Appendix A. 4.13.5.3 Resettable Power Resettable power is typically used to power beam detectors, flame detectors and conventional 4-wire smoke detectors.
Page 80: Remote Station Applications
IFP-2000 Installation Manual 1. Wire Relay 1 and/or Relay 2 as needed for your application. See Figure 4-41 for the loca- tion of the relay terminals. 2. Configure the relay through programming (see Section 9.5). 4.15 Remote Station Applications 4.15.1 Keltron Model 3158 Installation The control panel is compatible with Keltron Model 3158, used for direct connection to a Keltron receiver.
Page 81 Control Panel Installation Not suitable for remote station protected premise service where separate transmission circuits are required for fire supervisory (if applicable), and trouble signals. Intended for connection to a polarity reversal circuit of a remote station receiving unit having compatible ratings. Example Figure 4-42 Keltron 3158 Connection to Control Panel 151430...
Page 82: City Box Connection Using The 5220 Module
IFP-2000 Installation Manual 4.15.2 City Box Connection Using the 5220 Module This section describes how to connect the control panel to a local energy municipal fire alarm box or “city box” as required by NFPA 72 Auxiliary Protected Fire Alarm systems for fire alarm service.
Page 83: Using The Idp-Relay Addressable Relay Module For City Box Connection
Control Panel Installation 4.15.3 Using the IDP-Relay Addressable Relay Module for City box Connection Wire the IDP-Relay as shown in Figure 4-44 UL listed Model 7642 Must be Installed in City Box Enclosure Figure 4-44 IDP-Relay Module for City box Connection 151430 4-45 firealarmresources.com...
Page 84: Nfpa 72 Polarity Reversal
IFP-2000 Installation Manual 4.15.4 NFPA 72 Polarity Reversal Note: Intended for connection to a polarity reversal circuit of a control unit at the protected premises having compatible rating. 4.15.4.1 Using the 5220 Module When the 5220 is wired and programmed for polarity reversal, it reports alarm and trouble events to a remote site.
Page 85: Using The 7644 Module
Control Panel Installation 4.15.4.2 Using the 7644 Module When the 7644 is used for polarity reversal, it allows alarm and trouble events to be reported to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset.
Page 86: Transmitter Activated By Dry Contacts
IFP-2000 Installation Manual 4.15.5 Transmitter Activated by Dry Contacts This section describes the connection of a UL 864 listed remote station transmitter to the IFP-2000 FACP dry contacts. The FACP contacts must be supervised by the remote station transmitter module using end-of-line resistors (ELRs) with a value determined by the trans- mitter manufacturer.
Page 87: Networking
Networking Section 5 Networking Network System Hardware Features IFP-2000 panels can be networked to create a virtual system that is larger than 636 addressable points. It is possible to have up to eight IFP-2000/RPS-2000 panels networked providing a maximum addressable point capacity of 5,088 points (636 x 8 = 5,088). 5.1.1 Networked Sites A networked site is a logical group of IFP-2000 and/or RPS-2000 panels that behave as...
Page 88: Direct Connect Wiring Option
IFP-2000 Installation Manual Direct Connect Wiring Option When networking a group of IFP-2000s and/or RPS-2000s within a 20 foot radius of each other, you may use the direct connect method to link the panels together in the site.The cable used must be shielded twisted pair communication grade cable. See Figure 5-1, direct connect wiring option.
Page 89 Networking 3. Configure the network terminators. The panels at both ends of the network bus must have DIP switches 8, 9, and 10 set to the “ON” position. All panels that are not at the BUS ends must have the terminators set to the OFF position. See Figure 5-2 4.
Page 90: Repeater Wiring Options
IFP-2000 Installation Manual Repeater Wiring Options Networking a group of IFP-2000s and/or RPS-2000s at a distance greater then 20 feet requires the use of a network repeater with each panel. Repeaters are used to travel long distances and/ or between buildings. Figure 5-3 shows the repeater wiring connection for style 4, class B as a solid line.
Page 91: Network Repeater Types
Networking 5.4.1 Network Repeater Types Network repeaters are available in two configurations. See Figure 5-4 1. P/N IFP-RPT-UTP is used for twisted pair copper wiring up to 3000 ft. between panels. 2. P/N IFP-RPT-FO is used for fiber optic cable or twisted pair wiring between panels. Figure 5-4 Types of Network Repeaters The IFP-RPT-UTP repeater is used for connecting panels via unshielded twisted pair wiring up to a maximum wiring distance of 3000 feet.
Page 92: Network Repeater Installation
IFP-2000 Installation Manual 5.4.2 Network Repeater Installation The network repeater mounts in its own cabinet. The cabinet must be placed within 2 feet of the main control panel cabinet in order for the 5 foot ribbon cable to reach between the repeater and the control panel.
Page 93 Networking 2. Use the 5’ ribbon cable to connect the IFP-2000 to the repeater board. Run an insulated wire from the screw terminal labeled TB2 on the repeater to an earth screw terminal on the control panel. Figure 5-6 Panel to Networked repeater connection 3.
Page 94: Network Repeater Cable Requirements
IFP-2000 Installation Manual combination of both repeater types can be used. See Figure 5-7, Figure 5-8, Figure 5-9, and Figure 5-10 for repeater wiring examples. 5.4.2.1 Network Repeater Cable Requirements Cable requirements for wire runs between repeaters. 1. All fiber cable must be multimode 62.5/125 micron cable with ST type connectors. It is important that the cable be verified to contain no more then 8dB of loss including the connectors.
Page 95: Fiber Optic Repeater Wiring
Networking 5.4.2.3 Fiber Optic Repeater Wiring Fiber optic cable between multiple panels is shown in Figure 5-8. Class A is shown with a dotted line. Class A Wiring Figure 5-8 Fiber Optic Wiring Example 151430 firealarmresources.com...
Page 96: Fiber Optic And Twisted Pair Repeater Wiring Between Multiple Panels
IFP-2000 Installation Manual 5.4.2.4 Fiber Optic and Twisted Pair Repeater Wiring between Multiple Panels A mixture of fiber optic cable and twisted pair wiring between multiple panels is shown in Figure 5-9. Class A cabling is shown with dotted line. Fiber optic ports that are not used must have their...
Page 97: Using Both Repeaters And Direct Connect Wiring On A Networked System
Networking Using Both Repeaters and Direct Connect Wiring on a Networked System Figure 5-10 below shows a network wiring example using both repeaters and direct connect wiring. All repeaters in the system must be placed only on panels that are at the ends of a direct connect BUS or connected to panels with no direct connect network wiring.
Page 98: Setting The Network Terminators At Panel Dip Switches And Repeater Jumpers
IFP-2000 Installation Manual 5.5.1 Setting the Network Terminators at Panel DIP Switches and Repeater Jumpers Use the following steps for determining DIP switch and jumper settings. 1. DIP switch positions 8 through 10 on the control panel are used for direct connect network BUS termination.
Page 99: Setting The Network Id For Each Panel
Networking Panel 5 is at the end of a direct connect BUS so its DIP switches 8, 9 and 10 must be ON to provide the direct connect BUS termination. Panel 6 looks like it is at the end of a direct connect BUS, but because it is also using a repeater its DIP switches 8, 9 and 10 must be OFF.
Page 100 IFP-2000 Installation Manual 5-14 151430 firealarmresources.com...
Page 101: Network Management
Network Management Section 6 Network Management Network Diagnostics 6.1.1 Ping Panel The Ping Panel menu allows you to continually ping any panel programmed into the network. As the selected panel is being pinged, the Ping Panel screen will display the reply time, minimum and maximum reply times, and sent and received counters.
Page 102: Edit Network
IFP-2000 Installation Manual 3. Press to enter the Learn Network Menu. 4. Press to add or remove panels connected to the network as member or guest. 6.2.2 Edit Network This Menu allows you to add a panel to the network, edit the panel name and edit the panels site assignment.
Page 103: Edit Site Name
Network Management 6.2.2.2 Edit Site Name 5. Press to edit the site name press. See Figure 6-2 Figure 6-2 Site Assignment 6.2.3 Edit Panel ID This menu option allows you to change the current Network Panel ID. It is best to carefully consider the network ID setting for each panel.
Page 104: Access Codes
IFP-2000 Installation Manual running the SKSS-2 (see also Section 10.4.15). In order for this communication to function properly both the computer (running the software) and the control panel must have matching computer account numbers and computer access codes. Before you program in this location you should know how your control panel will communicate with the downloading computer, either through direct connect USB or via the phone lines (Internal Modem).
Page 105 Network Management Table 6-1User Profile Selectable Panel Functions Type of Function Selectable Functions System Reset System Silence Panel Operations System Ack Fire Drill Key System Test Fire Drill Menu Indicator Test Walk Test no Report Walk Test- with Report Dialer Test Clear History Buffer Point Functions Disable/Enable Point...
Page 106: Edit Name
IFP-2000 Installation Manual functions that the user will have access to with their code. Note: Profile 1 (Fire Fighter’s Key) the user name and access code can not be edited. Profile 2 (Installer) the user name and panel functions can not be edited. 6.2.5.1 Edit Name 6.
Page 107: Dialer Assignments
Network Management 6.2.6.1 Dialer Assignments Each panel on the IFP-2000 network specifies which network dialer is used for reporting. The network dialer capability of the IFP-2000 system allows all panels to use the same dialer providing an economical solution for reducing the number of phone lines required for reporting purposes.
Page 108: Network Management Quick Reference
IFP-2000 Installation Manual Network Management Quick Reference Menu Options/Defaults Comments Learn Guest or member add or remove panels into the network See Section 6.2.1 Network Network Panel ID Edit Panel Edit Panel name Edit Site member See Section 6.2.2 Network Site Member Edit Site Name Edit Name...
Page 109 Network Management Menu Options/Defaults Comments Edit Name Edit Access Code System Reset System Silence System Ack. Fire Drill Key System Tests Fire Drill Menu Indicator Test Walk Test no- Report Walk Test w/Report Profile 1 is the profile that Dialer Test dictates what functions the Clear History Firefighter Key has access to.
Page 110 IFP-2000 Installation Manual Menu Options/Defaults Comments Dialer Dialer Primary Report Primary or 00= unused See Section Assignments Dialer secondary 6.2.6.1 Dialer Misc. Enable PI SIA See Section 6.2.6.2 Modifier Receiver Can report up to Receiver Number See Section 6.2.6.3 Configuration four receivers Receiver Format Contact ID...
Page 111: Idp Slc Device Install
IDP SLC Device Install Section 7 IDP SLC Device Install Caution! To avoid the risk of electrical shock and damage to the unit, power should be OFF at the control panel while installing or servicing. List of IDP SLC Devices The following IDP SLC devices can be used with the control panel.
Page 112: Maximum Number Of Devices
IFP-2000 Installation Manual Maximum Number of Devices The IFP-2000 supports IDP SLC devices. The maximum number of SLC devices per panel is 636. The number of 5815XLs is limited only by the maximum number of SBUS devices. Wiring Requirements for SLC Devices The following information applies to all SLC devices.
Page 113 IDP SLC Device Install Figure 7-1 and Figure 7-2 show how wire length is determined for out-and-back tap and T-tap style wiring. Figure 7-1 Calculating wire run length for a simple out and back tap When using T-taps, the total length of all taps and the main bus must not exceed 40,000 feet. This requirement must be met in addition to the maximum distance requirements for the various wire gauges.
Page 114: Wiring 5815Xl In Style 6 & 7 (Class A) Configuration
IFP-2000 Installation Manual 7.3.2 Wiring 5815XL in Style 6 & 7 (Class A) Configuration Figure 7-3 illustrates how to wire the SLC loop for Style 6 or Style 7 Class A installations. Note: Style 6 does not use short circuit isolator devices Note: Style 7 wiring you have to have an isolator module as the first device on the in and the out loops.
Page 115: Wiring Idp Slc Detectors
IDP SLC Device Install Wiring IDP SLC Detectors This section describes how to install IDP heat and smoke detectors. All detectors ship with installation instructions. Refer to each detectors installation instructions for more detailed information. This information applies to the following IDP models: •...
Page 116: Addressing Idp Slc Devices
IFP-2000 Installation Manual Addressing IDP SLC Devices All IDP devices are addressed using the two rotary dials that appear on the device board. Use the ONES rotary dial to set the ones place in a one or two digit number, and use the TENS rotary dial to set the tens place in a two or three digit number.
Page 117: Programming Overview
Programming Overview Section 8 Programming Overview This section of the manual is intended to give you an overview of the programming process. Please read this section of the manual carefully, especially if you are programming the control panel for the first time. The JumpStart feature automates many programming tasks and selects default options for the system.
Page 118: Output Points
IFP-2000 Installation Manual to Zone 1. Zone 1 is mapped to Output Group 1. 8.1.2 Output Points The first JumpStart AutoProgramming on a panel in default configuration creates three output groups and assigns output circuits as follows: Internal Power Supply Circuits 1-8: Configured as Notification and assigned to Group 1.
Page 119 Programming Overview 7. Select one of the following options from the menu that displays. - Review System Press if you need to review the JumpStart configuration. - Repeat JumpStart Press if you need to rerun JumpStart for any reason. - Accept Changes 1.
Page 120: Mapping Overview
IFP-2000 Installation Manual Mapping Overview This section of the manual is a higher level overview of mapping. Details about how to select mapping options appear in the appropriate subsections in Section 9. Mapping is an important concept with the control panel. In general terms, mapping is assigning or linking events to outputs that should activate when events occur.
Page 121: Input Point Mapping
Programming Overview 8.2.1 Input Point Mapping Input points are assigned to input zones. Any input point can be assigned to any input zone. (Input points can be assigned to one zone only. An input point can be designated as “Unused,” which means it has not been assigned to a zone.) Figure 8-2 Example of Input Point Assignment 151430...
Page 122: Output Circuit Mapping
IFP-2000 Installation Manual 8.2.2 Output Circuit Mapping Figure 8-3 is a simple example showing how to assign notification and relay output circuits to groups. Figure 8-3 Example of Assigning Output Circuits to Groups 151430 firealarmresources.com...
Page 123: Event Mapping
Programming Overview 8.2.3 Event Mapping There are 10 types of Zone events and 23 types of System Events that can be mapped (see below). For each event type, you can activate the output groups with specific output patterns. Event types are listed in Table 8-1. Mapping examples are shown in Figure 8-4, Figure 8-5 & Figure 8-6.
Page 124 IFP-2000 Installation Manual Figure 8-4 Example of Zone Events Mapped to output Groups and Patterns 151430 firealarmresources.com...
Page 125 Programming Overview Figure 8-5 Example of Zone Events Mapped to Output Groups and Patterns on a Single Panel 151430 firealarmresources.com...
Page 126 IFP-2000 Installation Manual Figure 8-6 Example of Events Mapped to Output Groups and Patterns Within a Networked Site 8-10 151430 firealarmresources.com...
Page 127: Mapping Led Points
Programming Overview 8.2.4 Mapping LED Points Figure 8-7 is a simple example showing how LED points are mapped to zones and output groups. Typically you would create two output groups for each zone, one for alarms and one for troubles. (LED points are available when models 5865-3/4 and/or 5880 are used with the system.) Figure 8-7 Example of LED Points Mapped to Output Groups (applies to Models 5865-3/4 and 5880)
Page 128: Mapping Led Points For A Networked System
IFP-2000 Installation Manual 8.2.5 Mapping LED Points for a Networked System Figure 8-8 Example of Expanding Mapping of LED Points Across Panels 8-12 151430 firealarmresources.com...
Page 129: Programming Using The 5655 Silent Knight Software Suite-2
Programming Overview Programming Using the 5655 Silent Knight Software Suite-2 You can use the 5655 Silent Knight Software Suite (SKSS-2) to program the control panel onsite or remotely (personnel will need to be onsite during the upload or download process). SKSS-2 is a software package that lets you easily program the control panel using a Windows- based computer and a modem* (not sold by Silent Knight).
Page 130: Selecting Options And Entering Data
IFP-2000 Installation Manual example. Figure 8-9 Moving through Main Menu (Main Menu used as an Example) 8.4.1.2 Selecting Options and Entering Data There are several ways to make programming selections using the control panel depending on which screen you are currently using. The chart below is a generic explanation. Press Select from a menu.
Page 131: Editing Keys
Programming Overview 8.4.1.3 Editing Keys The keys shown in Figure 8-10 are available for use when you are in the Panel Programming Menu. Figure 8-10 Editing Keys Available from the Panel Programming Menu 151430 8-15 firealarmresources.com...
Page 132: Programming Menu Quick Reference
IFP-2000 Installation Manual Programming Menu Quick Reference This section of the manual lists all Panel Programming options in the order they appear on the sub-menus. Default settings are indicated in text or marked with an *asterisk. The comments column provide quick information and a reference to a section (if applicable) which has more detailed information.
Page 133 Programming Overview Menu Options/Defaults Comments Enter Name1 Enter Number1 Group Name Section 9.4.1.1 Enter Name2 Enter Number2 Edit Group Select Group Group Properties VIP Switch 1 through 32 Section 9.4.1.2 Number Group Voice EVAC Y or N Section 9.4.1.2 Only Add Group Section 9.4.2 Select Group to...
Page 134 IFP-2000 Installation Manual Menu Options/Defaults Comments Enter Pt Input Point Type Select Function Per JumpStart (detector/switch) (cont.) UNUSED B NOTIF Select Group A NOTIF CONSTANT AUX PWR RESETABLE DOOR MAN PULL Select zone Latch and Non- latch feature only WATERFLOW Select zone appear for SUPERVSY...
Page 135 Programming Overview Menu Options/Defaults Comments For each phone line (1 & 2) select: Dialing Prefix Up to 9 digits none Section 9.6.2 # of Answer Rings Range: 00-15 Number of rings before panel answers a call from a computer Section 9.6.2.2 Touch Tone TT/PL TouchTone...
Page 136 IFP-2000 Installation Manual Menu Options/Defaults Comments Y (Enabled) Section 9.6.6.1 SYNC Strbs w/ Sil *Disabled N (Disabled) Y (Enabled) Section 9.6.6.2 Auto Display Oldest *Disabled Misc. Options 2 N (Disabled) Repeater Installed Y (Enabled) Section 9.6.6.3 Section 9.6.6.4 Repeater Class A N (Disabled Alarm Verification Enter time from 1 to...
Page 137: Programming
Programming Section 9 Programming This section of the manual describes how to manually program the control panel from the built-in annunciator. Each subsection discusses these menu options in detail. All options described in this section can be performed using the Silent Knight Software Suite (SKSS-2). Important! Before any customized programming is done, JumpStart AutoProgramming should be run first.
Page 138: Modules
IFP-2000 Installation Manual Modules This section lists the options available under the module option in the Panel Programming. The following modules are available for the control panel: 5824 serial/parallel printer interface module, RA-2000 remote fire alarm annunciator, 5815XL SLC expander, RPS-1000 intelligent power module, 5496 intelligent power module, 5880 LED I/O module, 5865 LED annunciator, VIP-50 50 watt audio amplifier, VIP-VCM voice control module, and VIP- RM2000 remote microphone.
Page 139: Setting The 5815Xl Wiring Class
Programming Press the to move to the next character. Figure 9-1 Edit module Name Programming Screen Example 9.2.1.2 Setting the 5815XL Wiring Class This option applies only to the 5815XL. Each module has a unique set of options that specifically applies to the functionality of the module being edited. 8.
Page 140: Adding A Module
IFP-2000 Installation Manual 9.2.2 Adding a Module If you need to add a new hardware module to the system, follow these steps. You must be in the Main Menu to perform this task. If necessary, enter the Installer Code. 1. Enter the installer code. The panel will automatically go to the main menu. 2.
Page 141: View Module List
Programming 9.2.4 View Module List To view a list of all modules, follow these steps. You must be in the Main Menu to perform this task. If necessary, enter the Installer Code. 1. Enter the installer code. The panel will automatically go to the main menu. 2.
Page 142: Edit Zone Properties
IFP-2000 Installation Manual A screen similar to the one shown in Figure 9-2 displays. Select a up to 40 characters for a descriptive name as shown in the diagram. Figure 9-2 Selecting a Name for a Zone See Appendix B for a list of available characters and their numeric designators. 9.3.1.2 Edit Zone Properties Zone properties consist of alarm delay characteristics, heat detector sensitivity, and smoke detector sensitivity.
Page 143 Programming Alarm Delay Characteristics 3. Select the alarm delay characteristics (see Table 9-1) by pressing the arrow. Table 9-1Alarm Delay Characteristics Type of Delay Description One Count (No Delay). When this option is enabled, an alarm occurs immediately when a single device of any of the following types goes into alarm: detector, manual pull, water flow, Aux1 or Aux2.
Page 144: Zone Accessory Options
IFP-2000 Installation Manual Smoke Detector Sensitivity IMPORTANT! Drift compensation is automatic for all smoke detectors (photoelectric and ionization). The feature is always in effect, no programming is required. See Section 10.4.11 for information about how to check if a detector is in UL compliance. All detectors in the zone will respond as programmed in this menu location.
Page 145: Delete Zone
Programming this zone can now be programmed through the Zone Edit sub-menu. Up to 999 zones can be used per panel. 9.3.3 Delete Zone To delete a zone, follow these steps: 1. Enter the installer code. The panel will automatically go to the main menu. 2.
Page 146: Group
IFP-2000 Installation Manual Group An output group is made up of output points that have been programmed to respond in the same way. Output groups simplify programming because you have to program the output characteristics that are common to all of the group points once, instead of programming each individual point.
Page 147: Edit Group Properties
Programming Group Name Example Figure 9-4 Editing Group Name Example 9.4.1.2 Edit Group Properties The Edit Group Menu allows you to select options for each group for the following items: • VIP switch number, which is used if it is a voice type group. •...
Page 148: Add Group
IFP-2000 Installation Manual Define Output Group Type Each output group is defined as either a voice output group or a non-voice output group. Output points that are audio circuits (all circuits on the VIP-50 and VIP-CE4) can only be assigned to voice output groups. Output points that are non-voice circuits (all other points and circuits that are on all modules except the VIP-50 and VIP-CE4) are assigned to non-voice output groups.
Page 149: Delete Group
Programming Please wait . . . 3. Press to enter group menu. 4. Press to add a group. The system will assign the next available group number. Properties for the new group can now be edited if desired (see Section 9.4.1.2). A total of 999 output groups can be defined. 9.4.3 Delete Group 1.
Page 150: View Group Points
IFP-2000 Installation Manual 9.4.4 View Group Points 1. Enter the installer code. The panel will automatically go to the main menu. 2. Select for Panel Programming. Display reads: Initializing Please wait . . . 3. Press to enter group menu. 4.
Page 151: Point
Programming Point You may need to change characteristics of individual input points (detectors and switches) even after using JumpStart AutoProgramming. This section explains how to change options for: type of input point; latching/non-latching status (switches); and name and zone assignment of a point. 9.5.1 Point Programming For 5815XL Module To program for an 5815XL Module points, follow these steps:...
Page 152 IFP-2000 Installation Manual Type Function Latching Option Comments Selection Latching Use this option when you want a photoelectric detector to indicate a SUP DET SUP PHOTO supervisory in alarm. Non Latching Use this switch type for manual pull stations. This input is always latched. MAN_PULL The switch can clear only when an alarm is reset.
Page 153 Programming Type Function Latching Option Comments Selection Output Point, a general use notification type. Use for driving standard OUTPUT PT Select Group notification appliances. Use constant power for applications that require a constant auxiliary power AUX CONST source. Power is always present at Constant circuits. NOTIF Use for auxiliary power, resettable applications.
Page 154: Point Programming For Internal Or External Power Module (Rps-1000)
IFP-2000 Installation Manual 9.5.2 Point Programming For Internal or External Power Module (RPS-1000) To program for an internal or external power module points: 1. Enter the installer code. The panel will automatically go to the main menu. 2. Select for Panel Programming. Display reads: Initializing Please wait .
Page 155 Programming Table 9-3 Menu choices for Internal/External Power Module Function Choices Type Selections Selections for Comments each Type Enter Point or Circuit UNUSED B NOTIF A NOTIF CONSTANT Constant auxiliary power. AUX PWR RESETTABLE Resettable auxiliary power. DOOR Door holder auxiliary power. MAN PULL Refer to comments column of Table 9-2 for description of these...
Page 156: Point Programming For 5880, And 5865 Modules
IFP-2000 Installation Manual 9.5.3 Point Programming For 5880, and 5865 Modules To program 5880 or 5865 module points: 1. Enter the installer code. The panel will automatically go to the main menu. 2. Select for Panel Programming. Display reads: Initializing Please wait .
Page 157: Assigning A Name To Points
Programming Press to skip module name edit. 13. Repeat Steps 1 through 13 for all points. 9.5.3.1 Assigning a Name to Points You can assign a name to a point to make it easier to recognize on a display. To edit a point name: 14.
Page 158 IFP-2000 Installation Manual 11. Press 12. Edit module name. See Section 9.5.3.1. Press to skip module name edit. 13. Repeat Steps 1 through 13 for all voice circuits. 9-22 151430 firealarmresources.com...
Page 159: System Options
Programming System Options This section of the manual explains how to customize software options that affect general operation of the system. This includes such items as: AC loss hours, system clock options, holidays schedule, telephone and reporting account options. Refer to each individual subsection for complete instructions.
Page 160: Dialing Prefix
IFP-2000 Installation Manual 5. Select Phone Line to be edited (1 or 2) by pressing the arrow, then press Figure 9-8 Phone Lines Editing Screen 9.6.2.1 Dialing Prefix Enter up to 8 characters to be used for such things as PBX dial-out codes, a pause, and so on. The following special characters are available: Pound (or number) key on the telephone Star key on the telephone...
Page 161: Number Of Answer Rings
Programming 9.6.2.2 Number of Answer Rings This option is used in conjunction with the SKSS-2. Use the option to determine the number of rings before the panel answers a call from the computer. Range is 00-15 rings. This option is factory-programmed as 06 rings, which should be compatible for most installations where the answering machine bypass feature is used.
Page 162: Answering Machine Bypass
IFP-2000 Installation Manual 10. Select Y (monitor line) or N (don’t monitor line) by pressing the arrow, then press 9.6.2.6 Answering Machine Bypass This option is used in conjunction with the SKSS-2. This feature ensures that an answering machine will not interfere with communication between the panel and the computer. If an answering machine is used at the panel site, enable this feature;...
Page 163 Programming A screen similar to the one shown in Figure 9-9 will display. Figure 9-9 Changing Day/Night Sensitivity Time 151430 9-27 firealarmresources.com...
Page 164: Holiday Days
IFP-2000 Installation Manual 9.6.4 Holiday Days Up to 18 dates can be designated as holidays. When day/night sensitivity is enabled, all photoelectric smoke detectors in the system will use night sensitivity for the entire day on days designated as holidays (see Section 9.6.3). To add or change a holiday, follow these steps.
Page 165 Programming with a water flow switch. The delay is system-wide. All water flow switches on the system will use the same delay period. To access the screen for programming water flow delay, follow these steps: 1. Enter the installer code. The panel will automatically go to the main menu. 2.
Page 166: Low Ac Report Time
IFP-2000 Installation Manual 9.6.5.2 Low AC Report Time Note: You must select 1-3 hours in UL central station installations and UL remote signaling installations. You can adjust the number of hours before a Low AC report will be sent to the central station. To program low AC report delay, follow these steps: Note: Steps continued from step 6 of Section 9.6.5.1.
Page 167: Change Ac Line Frequency
Programming 9.6.5.5 Change AC Line Frequency The panel’s AC line frequency is selectable for 50, 60 Hz, or Neither. AC Frequency feature dictates how the control panel will calculate time based on the AC line frequency used in the installation site. The “Neither” option can be used in areas where the AC line frequency is not dependable and you want the panel to calculate time from the internal crystal.
Page 168: Miscellaneous Options 2
IFP-2000 Installation Manual 9.6.6 Miscellaneous Options 2 Through this programming option you can turn the strobe synchronization during silence feature On or Off, and select the control panel to report events by zone or by point. To edit miscellaneous options 2: 1.
Page 169: Both Ports Used
Programming 9.6.6.4 Both Ports Used When the Both Ports Used option is set to Y (Yes) the IFP-RPT Repeater will supervise the network wiring on both repeater ports. 11. Press the arrow to toggle this selection between Y (Yes) or N (No). 12.
Page 170: Daylight Saving Time Start And End
IFP-2000 Installation Manual 9.6.7.2 Daylight Saving Time Start and End This option lets you to adjust the week and month Daylight Saving Time (DST) starts and ends. For this feature to work, you must enable (set to Yes) the DST option under Misc. Options 1 (see Section 9.6.7.2).
Page 171: Edit Banner Message
Programming 9.6.8 Edit Banner Message The banner is the message that displays on the panel LCD when the system is normal, that is, when no alarms or troubles exist and no one is currently using system menus. You can create a customized message, which can be up to 40 characters, two lines of 20 characters each.
Page 172: Edit Voice Commands
IFP-2000 Installation Manual 9.6.9 Edit Voice Commands When a voice output group is selected to be activated by a zone, the cadence pattern specified in mapping does not apply. For voice output groups, one of six system wide voice commands will activate depending on the type of event that caused the activation.
Page 173: Restore Defaults
Programming To run JumpStart AutoProgramming: 1. Enter the installer code. The panel will automatically go to the main menu. 2. Select for Panel Programming. Display reads: Initializing Please wait... 3. Select for JumpStart AutoProgramming. 4. Press the arrow to select “Yes” from the warning screen. 5.
Page 174: Vip-Vcm Maintenance
IFP-2000 Installation Manual VIP-VCM Maintenance This programming menu option enables the user to add and edit the user message stored in the VIP-VCM. See VIP-Series Installation Manual P/N 151286 for more information. 1. Enter the installer code. The panel will automatically go to the main menu 2.
Page 175: System Operation
System Operation Section 10 System Operation Operation of the control panel is simple. Menus guide you step-by-step through operations. This section of the manual is an overview of the operation menus. Please read this entire section carefully before operating the panel. Press to view Main Menu: Select the desired menu option.
Page 176: Annunciator Description
IFP-2000 Installation Manual 10.2 Annunciator Description Figure 10-1 shows the annunciator that is part of the control panel board assembly. Figure 10-1 Control Panel Annunciator 10-2 151430 firealarmresources.com...
Page 177: Lcd Displays
System Operation 10.2.1 LCD Displays The control panel LCD displays system messages, annunciates alarms, supervisories and troubles; provides status information; and prompts for input. These messages can be up to 160 characters, displaying over four lines of 40 characters each. Annunciator keys beep when they are pressed.
Page 178: Menu System
IFP-2000 Installation Manual 10.3 Menu System The control panel is easy to operate from Main Menu. To view the Main Menu press the button on the control panel or remote annunciator. The Main Menu will appear as shown in Section 10.3.1. Select the desired option. You will be prompted for as access code if required.
Page 179: Using The Menus
System Operation 10.3.2 Using the Menus To move through the menus: to move through the options in a menu. Use to move to a previous menu. To select an option: Enter the number of the option. –OR– Press (Enter key) if the option appears at the top of the menu (= symbol displays after the option number in this case).
Page 180: View Event History
IFP-2000 Installation Manual 10.4.4 View Event History Use the View Event History feature to display events on LCD. From the Main Menu, press to select Event History. Events will begin displaying with most recent events first. The panel can store up to 1000 events. When it reaches its 1000-event capacity, it will delete the oldest events to make room for the new events as they occur.
Page 181: Conduct A Walk Test
System Operation 10.4.7 Conduct a Walk Test 1. From the Main Menu, press for System Tests. Important If any alarm verification zones are being used, the user will be asked if they wish to disable alarm verification during walk test. This occurs for either walk test option.
Page 182: Silence Alarms Or Troubles
IFP-2000 Installation Manual 10.4.9 Silence Alarms or Troubles Press to turn off silenceable outputs and annunciator PZTs. If an external silence switch has been installed, activating the switch will silence alarms or troubles. If you are already using system menus when you press , you will not need to enter your code or rotate the key.
Page 183: View Status Of A Point
System Operation 5. A screen similar to those shown in Figure 10-3 will display. Figure 10-3 Checking Detector Sensitivity Compliance You can print detector status by uploading the detector status to and printing from SKSS-2. 10.4.12 View Status of a Point 1.
Page 184: Communicating With A Remote Computer
IFP-2000 Installation Manual 10.4.15 Communicating with a Remote Computer An installer at the panel site can initiate communications between the panel and a computer running the SKSS-2. You can use this feature to upload a panel configuration. For example, if you have made programming changes to an installation on site using an annunciator, you can send your changes to the computer, so that the central station will have the latest data about the installation.
Page 185: Operation Mode Behavior
System Operation to begin communication. 5. The panel will attempt to communicate with the computer. If communication was estab- lished, the upload task you created will be placed in the SKSS-2 job queue, awaiting pro- cessing. When processing is completed, an “Unsolicited Upload” task will appear in the queue.
Page 186 IFP-2000 Installation Manual Operation Occurs When System Behavior In This Mode You Can Mode Supervisory The system The dialer seizes control of the phone line Press (down arrow) to view the supervisory detects a and calls the central station. condition. A screen similar to this one displays. supervisory The on-board annunciator sounds a loud, condition.
Page 187 System Operation Operation Occurs When System Behavior In This Mode You Can Mode Reset All LEDs are on briefly then the LCD Menus are not available during the reset process. displays "ALARM RESET IN PROGRESS". If the reset process button is pressed completes normally, the date and time followed by a normal mode screen displays.
Page 188: Multi-Site Annunciator And Multi-Site User
IFP-2000 Installation Manual 10.6 Multi-Site Annunciator and Multi-Site user Access Multi-site displays are unique as they can display the status and event history of all sites they are assigned to. These displays can be especially useful in guard shacks or security centers. A multi-site display is indicated by the words “Multi-Site Display”...
Page 189: Releasing Operations
System Operation 10.7 Releasing Operations This control panel supports two types of releasing, Double Interlock Zone, and Single Interlock Zone. The Double Interlock Zone operation requires an interlock switch input in the system, and the Single Interlock does not. An interlock switch is typically a dry-contact pressure switch.
Page 190: Single Interlock Zone Releasing
IFP-2000 Installation Manual 10.7.1 Single Interlock Zone Releasing A single interlock zone utilizes a minimum of two addressable detectors and a designated manual release switch. Important! Only addressable detectors can be used. No conventional detectors can be used. Each Single Interlock Zone input requires at least one manual release switch. Conditions Required for an Pre-Alert Output Activation If any single addressable detector is activated, the “Pre-Alert”...
Page 191: Double Interlock Zone Releasing
System Operation 10.7.2 Double Interlock Zone Releasing A Double Interlock Zone uses a minimum of two Addressable detectors, a designated manual release switch, and an interlock switch input. An interlock switch is typically a dry-contact pressure switch and will be referred to as an interlock/pressure switch in this document. Important! Only addressable detectors can be used.
Page 192: Smoke Alarm Verification
IFP-2000 Installation Manual 10.8 Smoke Alarm Verification Figure 10-5 illustrates how the Smoke Alarm Verification cycle operates. Figure 10-5 Smoke Verification Cycle During the Confirmation Period if there is no alarm indication then the system will return to normal operation. 10.9 Function Keys The function keys on the IFP-2000 are macro keys that can simplify and make easy access of disabling/activating up to 50 output groups or individual points.
Page 193: Aborting An F-Key Macro Recording Session
System Operation 10.9.2 Aborting an F-Key macro recording session: 1. After an F-Key macro recording session has been started you can cancel the session at any time by accessing the F-Key Recording Menu and selecting ‘Abort FKEY Recording’ option. 2. This will exit you from the menu. 10.9.3 Erasing an F-Key macro: 1.
Page 194 IFP-2000 Installation Manual 10-20 151430 firealarmresources.com...
Page 195: Reporting
Reporting Section 11 Reporting This section lists receivers that are compatible with this control panel, and the reporting codes sent by the control panel for SIA and Contact ID formats. 11.1 Receivers Compatible with the Control Panel Table 11-1 shows receivers compatible with the control panel. Table 11-1: Receivers Compatible with the Control Panel Manufacturer Model...
Page 196 IFP-2000 Installation Manual SIA Reporting Format Contact ID Reporting Format SIA pi Modifier (same as IFP-1000 Rev 9) SIA IFP-2000 Fixed Length Format NN - panel ID Module ID # SIA Event XX - SBUS ID Event Event Description Parameter Qualifier Group # Contact #...
Page 197 Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier (same as IFP-1000 Rev 9) SIA IFP-2000 Fixed Length Format NN - panel ID Module ID # SIA Event XX - SBUS ID Event Event Description Parameter Qualifier Group # Contact # (If Any) Codes...
Page 198 IFP-2000 Installation Manual SIA Reporting Format Contact ID Reporting Format SIA pi Modifier (same as IFP-1000 Rev 9) SIA IFP-2000 Fixed Length Format NN - panel ID Module ID # SIA Event XX - SBUS ID Event Event Description Parameter Qualifier Group # Contact #...
Page 199 Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier (same as IFP-1000 Rev 9) SIA IFP-2000 Fixed Length Format NN - panel ID Module ID # SIA Event XX - SBUS ID Event Event Description Parameter Qualifier Group # Contact # (If Any) Codes...
Page 200: Sia - Intelliknight / Ifp-2000 Panels Pi Modifier Reporting
IFP-2000 Installation Manual 11.3 SIA - Intelliknight / IFP-2000 Panels PI Modifier Reporting: Events are sent to the central station as a variable length string: The event format is: EEZZZZ Where: Event code (2 characters) ZZZZ Event parameter (up to four digits – not zero filled) 1.
Page 201: Sia - Ifp-2000 Panel Dialer
Reporting 11.4 SIA – IFP-2000 Panel Dialer: (Differences/additional features are underlined) Events are sent to the Central Station Receiver as a fixed length string: The event format is: EEPPMMZZZZ Where Event code (2 characters) Panel number (2 digits – Zero Filled) (valid range from 1 to 64) Module number (2 digits –...
Page 202 IFP-2000 Installation Manual For examples see Table 11-3 Table 11-3 IFP-2000 SIA REPORTING EXAMPLES Event Fire Alarm-Zone Zone EE-PP-MM-ZZZZ FA32000015 Fire Alarm-Zone Zone EE-PP-MM-ZZZZ FA32000005 Fire Alarm-Point Point EE-PP-MM-ZZZZ FA32010123 Fire Alarm-Point Point EE-PP-MM-ZZZZ FA21330203 Expander Trouble EE-PP-MM-ZZZZ ET15110000 Auto Test EE-PP-MM-ZZZZ RP32000000 Battery Trouble-Panel 32...
Page 203: Testing And Troubleshooting
Testing and Troubleshooting Section 12 Testing and Troubleshooting 12.1 Troubleshooting This section of the manual offers suggestions for troubleshooting hardware problems. Please read this section if you encounter a problem when installing the control panel. If these suggestions do not solve your problem or if you encounter a problem that is not listed here, contact Silent Knight Technical Support at 800-328-0103 or 763-493-6455 for assistance.
Page 204: Periodic Testing And Maintenance
IFP-2000 Installation Manual Problem Possible Cause / Suggested Actions 5815XL module that has been physically Check the status of the 5815XL green LED. If it flashes in the pattern .5 sec. connected to the panel but is not being on / .5 sec. off, it is likely that the 5815XL has not been added to the system recognized.
Page 205: Event History
Testing and Troubleshooting 12.2.2 Event History The event history can be useful for tracking or recalling a trouble condition. 12.3 Built-in Troubleshooting and Testing Tools The fire control panel has several built-in testing and troubleshooting tools that can be utilized to save time while testing and troubleshooting points and SLC devices.
Page 206: Slc Multi Device Locator
IFP-2000 Installation Manual 12.3.2 SLC Multi Device Locator This feature is the same as SLC Single Device Locator, except you can locate up to 8 devices on a single search. Follow these instructions to locate multiple SLC devices: 1. Select (Point Functions) from the Main Menu.
Page 207: I/O Point Control
Testing and Troubleshooting 12.3.3 I/O Point Control This feature allows you to toggle any output on or off and trip any input device. This can be useful to test a point’s output mapping. Follow these steps to control a I/O point: 1.
Page 208: Earth Fault Resistance
IFP-2000 Installation Manual 12.3.4 Earth Fault Resistance Table 12-1 lists the earth fault resistance detection for each applicable terminal on the FACP. Table 12-1 Earth Fault Resistance Values by Terminal Terminal Label Low Biased High Biased Function (Values in Ohms) High High Trip...
Page 209 Testing and Troubleshooting Terminal Label Low Biased High Biased Function (Values in Ohms) High High Trip Restore Trip Restore SBUS SBUS2 OUT – – Communication – – SBUS Power – – – – – SBUS SBUS 2 IN – – Communication –...
Page 210 IFP-2000 Installation Manual 12-8 151430 firealarmresources.com...
Page 211: Installation Records
Installation Records Section 13 Installation Records This section of the manual is for you to use if you wish to track of how points, zones, and groups have been programmed. 13.1 Detector and Module Point Record If installing IDP SLC devices, use Table 13-1 to record detector points (up to 159 per SLC loop) installed on the on-board SLC loop and make a copy of Table 13-2 to record installed modules (up to 159 per SLC loop).
Page 212 IFP-2000 Installation Manual Zone / Zone/ Module Addr Description Module Addr Description Group Group On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board...
Page 213 Installation Records Zone / Zone/ Module Addr Description Module Addr Description Group Group On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board 151430 13-3 firealarmresources.com...
Page 214 IFP-2000 Installation Manual Additional SLC Devices Use the table below to record devices installed on additional 5815XLs. Make a copy of this page if additional pages are needed Table 13-2 Installation Record of Devices Installed on 5815XL. Zone / Zone/ Module Addr Description...
Page 215 Installation Records Zone / Zone/ Module Addr Description Module Addr Description Group Group 151430 13-5 firealarmresources.com...
Page 216: Conventional Output Point Record
IFP-2000 Installation Manual 13.2 Conventional Output Point Record This chart can be used to keep track of how conventional output points (circuits) have been configured. Point/Circuit Group Description 13-6 151430 firealarmresources.com...
Page 217: Appendix A Compatible Devices
Compatible Devices Appendix A Compatible Devices Notification Appliances For Proper operation, you must use polarized devices with a model 7628 4.7k ohm EOL resistor on each loop. All supervised notification appliances used with the control panel must be polarized. Note: Not all devices can use the Sync feature, be sure to check Table A-1 to ensure the devices you have chosen will work with this feature.
Page 218 IFP-2000 Installation Manual Table A-1 Compatible Notification Appliances Manufacturer Model Audio Visual Type 130-3147C Mini Horn BLV-6 Vibrating Bell (con’t) BLV-10 Vibrating Bell BLVCH Vibrating Chime H12/24-FC Horn H12/24W-FC Horn H12/24K-FC Horn HC12/24-FC Horn HC12/24W-FC Horn HC12/24K-FC Horn P2415-FC Horn/Strobe P2415W-FC Horn/Strobe P2415K-FC...
Page 219 Compatible Devices Table A-1 Compatible Notification Appliances Manufacturer Model Audio Visual Type Horn Federal Signal VALS Horn/Strobe GEC-24-15 Horn/Strobes GEC-24-30 Horn/Strobes GEC-24-60 Horn/Strobes GEC-24-75 Horn/Strobes GEC-24-177 Horn/Strobes GX91 MiniHorn Steady Tone GX93 MiniHorn Temporal Tone HG124 Horn HS24-15 Horn/Strobe HS24-30 Horn/Strobe HS24-60 Horn/Strobe...
Page 220 IFP-2000 Installation Manual Table A-1 Compatible Notification Appliances Manufacturer Model Audio Visual Type Gentex ST24-110 Strobe ST24-1575 Strobe (cont) WGEC24-75W Weatherproof Horn/Strobe WGES24-75W Weatherproof Strobe WGMS-24-X Horn/Strobe GEC-24-110 Horn/Strobes GEC-24-15/75 Horn/Strobes Chime Chime CHSR 2-Wire Chime/Strobe CHSW 2-Wire Chime/Strobe Horn Horn Horn 2-Wire Horn/Strobe...
Page 221 Compatible Devices Table A-1 Compatible Notification Appliances Manufacturer Model Audio Visual Type System Sensor 4-Wire Horn/Strobe PC4R 4-Wire Horn/Strobe (con’t) P4RH 4-Wire Horn/Strobe High Candela 4-Wire Horn/Strobe PC4W 4-Wire Horn/Strobe P4WH 4-Wire Horn/Strobe High Candela PC4WH 4-Wire Horn/Strobe High Candela P4RK 4-Wire Horn/Strobe PC4RK...
Page 222 IFP-2000 Installation Manual Table A-1 Compatible Notification Appliances Manufacturer Model Audio Visual Type AH-12 Horn AH-24 Horn AH-12WP Horn Weatherproof AH-24WP Horn Weatherproof AMT-241575W Multi-Tone Horn Strobe AMT-24MCW Multi-Tone Horn Strobe AMT-241575W-NYC Multi-Tone Horn Strobe AMT-12/24 Multi-tone Horn AMT-12/24 NYC Multi-tone Horn AS-121575W Horn/Strobe...
Page 223 Compatible Devices Table A-1 Compatible Notification Appliances Manufacturer Model Audio Visual Type Wheelock MT-24MCW Multitone Horn Strobe (con’t) MTWP-2475W Multitone Horn Strobe MTWP-2475C Multitone Horn Strobe MTG-121575W Multitone Horn Strobe MTR-121575W Multitone Horn Strobe MTWPA-2475W Multitone Horn Strobe MTWPB-2475W Multitone Horn Strobe MTWPG-2475W Multitone Horn Strobe MTWPR-2475W...
Page 224 IFP-2000 Installation Manual Table A-1 Compatible Notification Appliances Manufacturer Model Audio Visual Type Wheelock RSSR-2475C Strobe RSSR-24110C Strobe (con’t) RSSA-24110W Strobe RSSB-24110W Strobe RSSG-24110W Strobe RSSR-24110W Strobe RSSA-24MCC Multi-Cd Strobe RSSB-24MCC Multi-Cd Strobe RSSG-24MCC Multi-Cd Strobe RSSR-24MCC Multi-Cd Strobe RSSWPA-2475W Strobe Weatherproof RSSWPA-24MCCH Strobe Weatherproof...
Page 225 Compatible Devices Two Wire Detectors Table A-2 lists two-wire smoke detectors that are compatible with the fire control panel. The table is organized by manufacturer. The columns show the number of detectors per loop that can be used. IFP-2000 Identifier 17.1 - 27.3 VDC Operating voltage Range Note: The maximum number of smoke detectors per zone is determined by both the current draw and the imped-...
Page 226 IFP-2000 Installation Manual Table A-2: Compatible Two-Wire Smoke Detectors Style B Model Name or Number Compatibility ID Manufacturer (Base model name or number in # per Loop Head Base parentheses.) 1400 16 / loop 1451 (B401B) 16 / loop 2100 20 / loop 2100T 20 / loop...
Page 227 Compatible Devices Four-Wire Smoke Detectors/Devices (UL Listed) Table A-4 Compatible Four-Wire Smoke Detectors Max Standby Alarm Smoke Detector/Base Detector Type Current (mA) Current (mA) Fenwal CPD-7021 (w/70-201000-005 Base) Ionization 0.10 Fenwal PSD-7125 Photoelectric 0.10 Fenwal PSD-7126 (w/70-201000-005 Base) Photoelectric 0.10 Fire-Lite BLP-12-4W Base Photoelectric...
Page 228 IFP-2000 Installation Manual Max Standby Alarm Smoke Detector/Base Detector Type Current (mA) Current (mA) System Sensor 4WTR-B (12/24 Volt) Photo w/ Therm/Relay System Sensor 4WTAR-B (12/24 Volt) Photo w/ Therm/ Sounder/Relay System Sensor 4WITAR-B (12/24 Volt) Photo w/ IsolatedTherm/ Sounder/Relay System Sensor 2W-MOD2 Loop Test/Maintence Mod.
Page 229 Compatible Devices Door Holders (UL Listed) Table A-5 list door holders that are compatible with the fire control panel. Table A-5 Compatible Door Holders Current MANUFACTURER MODEL TYPE (mA) Edwards DH150A Floor Mount Edwards DH154A Flush Mount Edwards DH158A Surface Mount Rixon Firemark FM-980 Floor Mount, single...
Page 230 IFP-2000 Installation Manual A-14 firealarmresources.com...
Page 231: Special Characters Lists
Special Characters Lists Appendix B Special Characters Lists This section contains tables of programmable characters that may be used for device, module, and zone names or phone numbers. Characters used for Naming Table B-1 list the available character and their associated numeric designator. When programming these numbers can be entered as a short cut to using the up or down arrow keys, to select characters when naming a point or zone.
Page 232 IFP-2000 Installation Manual 151430 firealarmresources.com...
Page 233: Silent Knight Fire Product Warranty And Return Policy
Silent Knight Fire Product Warranty and Return Policy General Terms and Conditions • All new fire products manufactured by Silent Knight have a limited warranty period of 18 months from the date of manufacture against defects in materials and workmanship. See limited warranty statement for details.
Page 234 No credit will be issued if the returned board was damaged due to misuse or abuse. • Repairs and returns should be sent to: Silent Knight / Honeywell Attn: Repair Department 7550 Meridian Circle N., Suite 100 Maple Grove, MN 55369-4927 RA Number:___________________ firealarmresources.com...
Page 235 Limited Warranty SILENT KNIGHT warrants products manufactured by it to be free from defects in materials and workmanship for eighteen (18) months from the date of manufacture, under normal use and service. Products are date stamped at time of manufacture. The sole and exclusive obligation of SILENT KNIGHT is to repair or replace, at its option, free of charge for parts and labor, any part that is defective in materials or workmanship under normal use and service.
Page 236 firealarmresources.com...
Page 237 firealarmresources.com...
Page 238 SILENT KNIGHT ® by Honeywell 7550 Meridian Circle, Suite 100 Maple Grove, MN 55369-4927 763-493-6455 or 800-328-0103 Fax: 763-493-6475 www.silentknight.com © 2008 Honeywell International Inc. firealarmresources.com...

This manual is also suitable for:

Silent knight ifp-2000

Honeywell SILENT KNIGHT RPS-2000 Installation And Operation Manual

Quick Links

Troubleshooting

Related Manuals for Honeywell SILENT KNIGHT RPS-2000

Summary of Contents for Honeywell SILENT KNIGHT RPS-2000