UFO MicroLED 4000P Product User Manual
Hide thumbs
Also See for MicroLED 4000P:
- Product user manual (12 pages) ,
- Product user manual (13 pages) ,
- Product user manual (13 pages)
Related Manuals for UFO MicroLED 4000P
Summary of Contents for UFO MicroLED 4000P
- Page 1 PRODUCT USER GUIDE MicroLED 4000P Illuminator Rev: C1 PLEASE READ THIS USER GUIDE BEFORE INSTALLING OPERATING OR PERFORMING MAINTENANCE ON THE LLUMINATOR UNIT E357731...
- Page 2 INTRODUCTION Thank you for purchasing this UFO Illuminator/luminaire. To ensure that the Illuminator is set up optimally and gives a long service life, please read this user guide before installing, operating or performing any maintenance on the unit. Please keep this User Guide for future reference. This User Guide is laid out in three sections •...
-
Page 3: Installation
This luminaire is powered by a 12V Power Supply Unit or 12V Constant Voltage Driver. Remove the PSU/driver from its box. Connect the jack plug into the socket in the back, and the Illumina- tor is now ready for connection. UFO LIGHTING... -
Page 4: Remote Control
INSTALLATION CONNECTION There are 2 connections required - the fiber port and the mains supply. The fiber port should be connected first. Connect and secure the fiber optic connector into the front of the unit and secure using the M5 locking screw. Plug the mains plug into the electrical supply socket. -
Page 5: Operation
5 within 3 seconds and the Illuminator will “blink” 9 times indicating that the Remote Controller is unmatched from the Illuminator. NOTE: - More than one Illuminator controlled by one Remote Controller will eventually run out of sync with each other (color cycle mismatch) UFO LIGHTING... - Page 6 OPERATION REMOTE CONTROL MODES AND FUNCTIONS Mode Brightness Speed Comment Touch color ring then Static white Adjustable Non adjustable mode + to enter this mode at any time Color ring control. Touch White and col Adjustable Non adjustable color ring to enter this ors mixed mode at any time All colors fade...
- Page 7 Note: Where a Illuminator has more than one remote control, reduction in operating range may be experienced when both (or multiple) remote controls are used simultaneously. Description Date Max Range Controller 1 Controller 2 Controller 3 Dead Areas UFO LIGHTING...
- Page 8 OPERATION STANDALONE OPERATION USING INBUILT BUTTONS To disable the remote and revert to manual operation press one of the buttons on the rear of the Illuminator. The Illuminator will now respond to manual commands from the 2 control but- tons as described below. The Illuminator has 2 color cycles, each with 3 different speed settings, the colors are detailed in the table below: Cycle...
-
Page 9: Operation And Maintenance
MicroLED 4000 Slave Illuminators. See MicroLED 2000 or MicroLED 4000 Slave User Guides for DMX wiring connections MAINTENANCE LOG Date Maintenance Undertaken Note: A record of all maintenance MUST be kept in the table above, indicating what maintenance was undertaken and when. This MUST be dated for warranty purposes. UFO LIGHTING... -
Page 10: Troubleshooting
TROUBLESHOOTING Problem Possible Cause(s) Remedy Unit is dead LED Mains supply off Check supply and reinstate power Loose mains plugs Check plugs indicator is not PSU failed Replace PSU illuminated Unit is dead no LED array failure Replace LED unit light output but LED power indicator is Recycle power to Illuminator or switch on via... -
Page 11: Technical Specification
Remote Control Frequency 2.4Ghz Remote Control Range 30m, depending on environment Remote Control Power 2 x AAA batteries Material Finish Black, white or silver Dimensions (L x W x H) / Weight 137mm x 114mm x 73mm / 389g UFO LIGHTING... - Page 12 United Kingdom • United States • Germany • Europe • Universal Fiber Optics Ltd Universal Fiber Optics USA LLC UFO Licht GmbH Home Place Coldstream 1749 Northgate Blvd Andreasstraße 20 TD12 4DT Sarasota FL34234 93059 Regensburg Deutschland +44 (0)1890 883416...