Table of Contents
Quick Links
Light Source
Luna Slimline Plastic Light Source Range
Please read this manual fully before installing, operating or performing
Issue 4 | Revised: 310317
User Guide
Models covered by this manual:
UFO LUNA SLP-3000M
UFO LUNA SLP-4000M
UFO LUNA SLP-3000DMX
UFO LUNA SLP-4000DMX
UFO LUNA SLP-300010V
UFO LUNA SLP-400010V
maintenance on the light source unit.
Universal Fibre Optics
Home Place | Coldstream | TD12 4DT | United Kingdom
Tel: +44 (0)1890 883416 | Fax: +44 (0)1890 883062
www.fibreopticlighting.com
Table of Contents
Related Manuals for UFO LUNA SLP-3000M
Summary of Contents for UFO LUNA SLP-3000M
- Page 1 Light Source User Guide Luna Slimline Plastic Light Source Range Models covered by this manual: UFO LUNA SLP-3000M UFO LUNA SLP-4000M UFO LUNA SLP-3000DMX UFO LUNA SLP-4000DMX UFO LUNA SLP-300010V UFO LUNA SLP-400010V Please read this manual fully before installing, operating or performing maintenance on the light source unit.
- Page 2 Please read these instructions fully before connecting your unit to the electrical supply, and keep them for future reference. The UFO Luna range of light sources are suitable for use with either glass or PMMA fibre optic harnesses. This luminaire is powered by a 24V Power Supply Unit or 24V constant voltage driver.
-
Page 3: Installation Instructions
The LED light source is powered from a 24V DC PSU/Constant Voltage SELV LED driver. Remove the 24V PSU/driver from its box. The driver caters for UK/European/other mains supplies using the relevant power cord supplied. UFO LUNA SLP-M UFO LUNA SLP-DMX UFO LUNA SLP-10V... - Page 4 CONNECTION – LUNA M There are 2 connections required – the fibre port and the mains supply cable. The fibre port should be connected first. Connect and secure the fibre optic connector into the collar and secure using the M5 locking screw. Connect the PSU/driver to the DC input jack socket on the Luminaire.
- Page 5 The recommended plug for these sockets is Multicomp SVP556-TA. The pin out details for the plugs are shown below. Either socket may be used as DMX in or DMX out. NOTE: CONVERTORS ARE AVAILABLE FROM UFO Mini XLR to RJ45 Mini XLR to normal 3 pin XLR...
-
Page 6: Dmx Operation
DMX OPERATION The DMX light siources can be dimmed remotely (single Channel 0-255 – SEE TABLE BELOW) and can be addressed manually Single Channel Value Description LED Off LED Brightest Unless the address is specified on the Purchase Order, all light sources will be defaulted to Address 001. -
Page 7: Setting The Dmx Address
SETTING THE DMX ADDRESS 1. Disconnect the light source from the mains supply. 2. Tilt the light source on its side and remove the screw from the base as shown below. 3. Slide the access cover down to remove and set the cover and screw aside. 4. - Page 8 SETTING THE DMX ADDRESS DMX B DMX B START Switches START Switches Channel # Channel # 1,2,4 1,3,4 2,3,4 1,2,3,4 1,2,3 1,2,3,4,5,6, 7,8,9 NOTE: With DIP switch 10 OFF, the light source will not illuminate unless a DMX signal is present. Luna Light Source Range...
- Page 9 The recommended plug for these sockets is the Multicomp SVP556-TA. The pin out details for these plugs are shown below. Either socket may be used as 0-10V IN or 0-10V OUT NOTE: CONVERTORS ARE AVAILABLE FROM UFO Mini XLR to RJ45 Mini XLR to normal 3 pin XLR...
- Page 10 0-10V SETTINGS The following table represents light output percentage against approximate control value input. Light Output Percentage Voltage 100% 7 - 10V 6.2V 5.8V 5.4V 4.5V 3.9V 3.2V 2.3V 1.4V 1.1V 2.5% 0.8V 1.25% 0.4V 0.2V NOTE: THE LIGHT SOURCE WILL NOT ILLUMINATE UNLESS A 0-10V CONTROL VOLTAGE IS PRESENT.
-
Page 11: Maintenance
MAINTENANCE Please Note that a record of all maintenance MUST be kept in the table below, indicating what maintenance was undertaken and when. This MUST be dated for warranty purposes. Date Maintenance Undertaken Universal Fibre Optics... -
Page 12: Troubleshooting
TROUBLESHOOTING Problem Probable Causes Remedy Mains supply off Check supply & reinstate Loose mains plugs Check plugs Unit is dead – no light output and LED power indicator on Plug fuse blown (UK) Check fuse. If blown, replace PSU is not illuminated PSU failed Replace PSU Unit is dead –... - Page 13 ADDITIONAL TROUBLESHOOTING (0-10V MODELS ONLY) Problem Probable Causes Remedy No 0-10V dimming to unit Refer to manual diagram for (0V= LED Off) correct termination. Carry out continuity check. Carry out voltage / polarity check 0-10V cable fault 0-10V Version unit is dead - no light output - but LED indicator on light source is illuminated.
-
Page 14: Technical Specifications
TECHNICAL SPECIFICATIONS Description Details Port connector size 30mm Fibre type Glass/PMMA 200-240V 50/60Hz (range dependant on Mains Supply voltage PSU/driver) PSU Output 24V DC 12W minimum LED Power 11.5W max. Min Ambient Temperature -10ºC Max Ambient Temperature +45ºC 2.1 x 5.5 x 12mm Power Connection LED Type / Model White light... - Page 15 Universal Fibre Optics...
- Page 16 Universal Fibre Optics Home Place | Coldstream | TD12 4DT | United Kingdom Tel: +44 (0)1890 883416 | Fax: +44 (0)1890 883062 www.fibreopticlighting.com...