Table of Contents
Table of Contents
Related Manuals for Bosch Rexroth CS660
Summary of Contents for Bosch Rexroth CS660
- Page 1 CS660/CS661 Spreader Controller Operator Manual...
-
Page 2: Table Of Contents
Error Messages Bosch Rexroth Canada Corp. reserves the right to revise this information at any time and for any reason and reserves the right to make changes at any time, without notice or obligation, to any of the information contained in this piece of literature. -
Page 3: Operator Interface And Basic Operation
Spinner Anti-ice rate Rate Gate Position Pre-wet (tap to change) Rate Turn: Spinner Turn: Conveyor Turn: Anti-Icing Spreading Turn: Pre-wet (If configured) Press: Pause Press: Blast Rate Press: Momentary Conveyor Reverse Bosch Rexroth Canada I December 2020 ı Revision 2.0... - Page 4 – This shows the current Driver ID, and allows the selection and naming of Driver IDs. To select one of four Driver IDs, press on the Driver name and a list will drop down. Bosch Rexroth Canada I December 2020 ı Revision 2.0...
- Page 5 To enter the weight, press and hold the weight for 5 seconds and a keypad will pop up: Enter weight, then press enter key Bosch Rexroth Canada I December 2020 ı Revision 2.0...
-
Page 6: Additional Feature Functions
The Conveyor can work in either forward or reverse direction selected by a rocker switch wired to a digital input of the 660 system. The Reverse operation is indicated by a red “R” in the conveyor control panel. Conveyor reversing Bosch Rexroth Canada I December 2020 ı Revision 2.0... -
Page 7: Spinner Forward And Reverse
The Reverse is indicated by a red “R” in the Spinner and Conveyor control panels. Conveyor reversing Spinner reversing 2.4 Dual Spinner Dual spinner is selected by a switch. A red ‘D’ is displayed in the spinner panel when it is selected. Dual spinner enabled Bosch Rexroth Canada I December 2020 ı Revision 2.0... -
Page 8: Boom Anti-Ice
A gate position sensor to monitor the actual gate position in real time. With the Read back sensor operators do not need to enter on screen when adjusting gate position for different materials. Readback Indicator Bosch Rexroth Canada I December 2020 ı Revision 2.0... -
Page 9: Lane Control
Operator can adjust spreading width by an increment of half lane or one lane depending on the configuration. With the lane control the solid application rate is lbs per lane mi or kg per lane km. Dial spinner knob to change lane width Bosch Rexroth Canada I December 2020 ı Revision 2.0... -
Page 10: Knob) Spreader + 1Boom Anti-Ice
The 4 knobs(leftright) are for Spinner, Conveyor, Prewet and Cross Conveyor console with an external direction switch to control the cross conveyor direction that is displayed with the dot at the bottom of the cross conveyor panel. Direction indicators Bosch Rexroth Canada I December 2020 ı Revision 2.0... -
Page 11: Knob) Spreader + 3 Boom Anti-Ice + Cross Conveyor
Deadman trigger. Note: The joystick will only operate while the Deadman Trigger is pulled. The default spreader or joystick screen is selectable on USER setup screen. Bosch Rexroth Canada I December 2020 ı Revision 2.0... -
Page 12: Data Retrieval/Clear Trip Summary
With NO USB Key inserted. Press on the RPM icon to display trip summary information. Once this window is visible, press and Confirmation hold the RPM icon message for 5 seconds Bosch Rexroth Canada I December 2020 ı Revision 2.0... -
Page 13: Error Messages
57 Calib gate needs to be non-zero SPN SENSOR PULSES TOO LOW 58 Spin sensor pulses 0 or too low CONV SENSOR PULSES TOO LOW 59 Conv sensor pulses 0 or too low Bosch Rexroth Canada I December 2020 ı Revision 2.0...