Table of Contents
Quick Links
Table of Contents
Related Manuals for Hitachi UHD8410PC
Summary of Contents for Hitachi UHD8410PC
- Page 1 84’’(213cm) INTERACTIVE MONITOR UHD8410PC - UHD8410...
-
Page 2: Table Of Contents
Contents Contents ..............1 Important Safety Information ........3 BATTERY SAFETY GUIDELINES ......5 CHAPTER 1 ............6 CHAPTER 2: ............6 RS232 Command Table .........8 Part Names............10 OPS (Open Pluggable Specification) PC- Optional ..............10 CONNECTING PERIPHERAL EQUIPMENT ..11 TURNING POWER ON/OFF ........ 11 BASIC OPERATION ..........12 Function Buttons and Remote Control ....13 Remote Control Operating Area ......14... - Page 3 Disposal of old Equipment and Batteries Only for European Union and countries with recycling systems. The above mark is in compliance with the Waste Electrical and Electronic Equipment Dire- ctive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries as unsorted municipal waste, but use the return and collection systems available.
-
Page 4: Important Safety Information
• Put the product on a well-ventilated place and Important Safety Information prevent from bright light, overheat and damp. • The product should be kept in 0 C° - 40 C°. CAUTION Otherwise, the appliance may be damaged permanently. RISK OF ELECTRIC SHOCK DO NOT OPEN •... - Page 5 product may cause electric shock, short circuit of the • Unplug the power cord if it is not used for a long time. internal parts and/or fire. For the same reason, do not • Do not attempt to repair the power cord if it is broken spill water or liquid on the product.
-
Page 6: Battery Safety Guidelines
• Damages and faults that occur during transport after Incorrect fitting can cause leakage or, in extreme the delivery of the appliance to the customer are not cases, fire or even an explosion. included in the warranty cover. • Replace the whole set of batteries at one time, taking •... -
Page 7: Chapter 1
Introduction CHAPTER 1 This instruction manual is intended to help you operate INTRODUCING THE “INTERACTIVE BOARD” your “INTERACTIVE BOARD” product in a proper way Congratulations for buying our the 84”(213cm) and get a better performance. INTERACTIVE BOARD product! Chapter 1. Introducing “INTERACTIVE BOARD” The “INTERACTIVE BOARD”... - Page 8 What is Situation Method required to continue In order to prevent data loss, please turn off your system by following the procedure in your operating system. In case your system does not respond to the Turning off procedural shut down Pressing the the system because of resource...
-
Page 9: Rs232 Command Table
RS232 Command Table - Baud rate 192000 Function Function Command Data(HEX) Additional Information Name Type BE EF 03 06 00 2A D3 01 00 00 60 00 00 BE EF 03 06 00 BA D2 01 00 00 60 01 00 Power BE EF 03 06 00 19 D3 02 00 00 60 00 00... - Page 10 INCREMENT BE EF 03 06 00 19 D4 03 00 00 60 03 00 only VGA Clock DECREMENT BE EF 03 06 00 19 D5 03 00 00 60 04 00 only VGA BE EF 03 06 00 19 D7 03 00 00 60 06 00 1D XX XX: value only VGA...
-
Page 11: Part Names
Part Names OPS (Open Pluggable Specification) PC- Optional Front View Tips • OPS is an optional plug&play PC. It may be based on intel or ARM based PC. • DS (Digital Signage) monitor is complying with both intel ARM based OPS PC. USB 3.0 USB 2.0 Ethernet... -
Page 12: Connecting Peripheral Equipment
• Use Source Select button (11 Source Select But- CONNECTING PERIPHERAL ton) to set mode as an HDMI. EQUIPMENT Tips • The length of the signal cables or surrounding environment may affect the image quality. Connecting The Power Cord Caution! •... -
Page 13: Basic Operation
Status of LED Status of the Monitor&PC Power Off / Standby mode Tips • After turning the product off, it will automatically enter standby mode approximately 60 sec. later. BASIC OPERATION 1-17. ON/OFF Use these buttons to adjust the brightness. 2-16. -
Page 14: Function Buttons And Remote Control
However, System On/Off turns on/off the system so Replacing the Batteries system will enter standby mode. Warning! •Remote Control may not work properly if there Rotate left to open Remove the old battery and would be any object under the product closer than Install the new one w�th the plus (+) symbol fac�ng up 100cm. -
Page 15: Remote Control Operating Area
Remote Control Operating Area Definition of Source Transition Definition of Source Transition by Button Chart Press the source “ ” button to reach the source selection menu by button chart. The source menu will be displayed as below. The desired mode can be selected by pressing Right-Left buttons on IR or Keypad. - Page 16 If the chosen source has no signal, a warning will be displayed as below. OSD Menu can be reached by pressing “Menu” Button on Remote Controller or Keypad. - 15 -...
-
Page 17: Battery Safety Guidelines
Battery Safety Guidelines CAUTION : Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. BATTERY SAFETY GUIDELINES Make sure battery compartments are secure. - 16 -... -
Page 18: Chapter 3
Interactive Board, the processing system should be started. WARNING: If any drivers are missing or you require technical support - please contact pj.support@ hitachi-eu.com. Touch Screen Installation 3.1.1. About installation 1. Before starting installation, ensure that all drivers are installed correctly and USB are installed correctly. -
Page 19: Connections Diagram
3. Having touched the four calibration points, a Connections Diagram dialogue box will pop up. Click “Yes” to save the calibration data and “No” not to. If you don’t click yes Opt�onal PC (OPS) Module or no within 10s, you will automatically exit the calibration process without saving the data. - Page 20 Image transfer by an external source via HDMI - 19 -...
- Page 21 Image transfer by an external source via VGA Important! To transfer image and audio transfer via VGA at the same time, except for the VGA cable, an audio transfer cable should be also used as shown (3.5 mm stereo). - 20 -...
-
Page 22: Chapter 4
To use external source, to plug the Interactive Board CHAPTER 4 is enough. You can use external sources without C O N N E C T I O N O F O T H E R D E V I C E S O N connecting the Embedded PC. - Page 23 CHAPTER 5 Processing System Windows Drivers The drivers in that CD are updated drivers providing your device to function properly. Copies of drivers in the CD are also in D index of your device. You can get the updated drivers from the Service Centre.
-
Page 24: Chapter 5
4. Select the option Keep my files. Network Connection (Optional Pc Unit) Using the Network Connection Option Your “INTERACTIVE BOARD” product has a 1 0 / 1 0 0 / 1 0 0 0 L a n m o d u l e a n d i t c o n n e c t s “INTERACTIVE BOARD”... -
Page 25: Main Menu
Settings MAIN MENU In order to enter Aptio Installation Software, you Main menu is the first menu displayed when you enter shall press “DEL” key when you see the Bios logo the Bios. You may see the basic information for your while your system is starting up. -
Page 26: Chapter 8
CHAPTER 8 CHAPTER 9 USING YOUR “INTERACTIVE BOARD” TROUBLESHOOTING MORE EFFICIENTLY If you are experiencing any problem with your display, before calling for service, please review the following Paying attention to the following points with respect troubleshooting tips. to your “INTERACTIVE BOARD” will provide a stable performance and also prolong its life. - Page 27 The product makes a cracking sound. Check that your BIOS settings are adjusted properly. Hard disk module may be malfunctioning. Consult • You may occasionally hear a cracking sound technical support to get support. from the product. This happens when the cabinet Symptom: The hard disk runs more and more slowly slightly expands and contracts according to change in temperature.
-
Page 28: Specifications
SPECIFICATIONS Make sure that “the correct driver is installed for the USB device” Other Issues: Check the USB cable Model Name UHD8410PC - UHD8410 Symptom: System hour and date is not correct. 84990 Check the following: Aluminum Front Cover Cabinet... - Page 29 PC Board Spec�f�cat�ons Mechan�cal Spec�f�cat�ons Processor Intel �5 3610ME Bezel W�dth (Left/R�ght, Top/Bottom) 38 mm/ 38 mm, 38 mm / 38 mm Ch�pset QM77 D�mens�ons (W x H x D) 1954 mm x 1139 mm 8GB 1333/1600MHz DDR-3 x 109 mm System Memory We�ght 106 kg...
-
Page 30: Product Technical Drawing Details
PRODUCT TECHNICAL DRAWING DETAILS PRODUCT MEASUREMENTS MOUNTING MEASUREMENTS OPS Connection Scheme Tips • OPS is an optional plug & play PC. It may be based on Intel or ARM based PC. • DS monitor is complying with both Intel and ARM based OPS PC. •... -
Page 31: Chapter 10
Receptacle Connector / TX24 Pinout CHAPTER 10 ASSEMBLY INSTRUCTION FOR INTERACTIVE MONITOR WALL MOUNT Use the monitor with the surface perpendicular to a level surface. Do not install the product on a ceiling or inclined wall. - 30 -... - Page 32 Manufacturer: Hitachi Europe Ltd., Whitebrook Park, Lower Cookham Road, Maidenhead, Berkshire SL6 8YA U.K. www.hitachidigitalmedia.com...