NEC UNIVERGE SV9100 Configuration Manual
  1. Manuals
  2. Brands
  3. NEC Manuals
  4. PBX
  5. Univerge SV9100
  6. Configuration manual

NEC UNIVERGE SV9100 Configuration Manual

Sip trunking service configuration guide for idt/net2phone
Hide thumbs Also See for UNIVERGE SV9100:
Table of Contents

Quick Links

See also: Administration Manual , Programming Manual
Table of Contents
loading

Related Manuals for NEC UNIVERGE SV9100

Summary of Contents for NEC UNIVERGE SV9100

  • Page 2 SV 9100 ® SIP Trunking Service Configuration Guide for IDT/net2phone NDA-31841 Issue 1.0...
  • Page 4 LL OTHER BRAND NAMES AND PRODUCT NAMES REFERENCED IN THIS DOCUMENT ARE TRADEMARKS OR REGISTERED TRADEMARKS OF THEIR RESPECTIVE COMPANIES Copyright 2017 NEC Corporation of America 3929 W. John Carpenter Fwy Irving, TX 75063 Communications Technology Group SIP Trunking Service Configuration Guide...
  • Page 5 Issue 1.0 IDT/Net2Phone Table of Contents...

  • Page 6: Table Of Contents

    TABLE OF CONTENTS Section 1 NEC SV9100 and IDT/Net2Phone Setup Guide ..........1 This Guide and Related Documents ............1 IDT/Net2Phone Account ................1 SV9100 System Software ................1 Requirements ....................2 General Information ..................2 Limitations ....................2 Section 2 NEC PBX Configuration ..................
  • Page 7 Issue 1.0 IDT/Net2Phone 3.11 IP Trunk Calling Party Number Setup ............19 3.12 IP Trunk (SIP) Calling Party Number Setup for Extensions ...... 20 3.13 DID (TN to ext map) .................. 21 3.14 SIP Trunk CODEC Setup ................. 22 3.15 ToS Setup ....................
  • Page 8 LIST OF FIGURES and TABLES Table 1 Installation Worksheet .................... 4 Figure 1 Blade Configuration ....................5 Figure 2 IPL DSP Resource Selection ................. 6 Figure 3 IP Trunk Availability ....................7 Figure 4 GCD-CP10 Network Setup ..................8 Figure 5 Blade License Setup ....................
  • Page 9 Issue 1.0 IDT/Net2Phone Table 4 Troubleshooting Guide ..................28 List of Figures and Tables...

  • Page 10: Nec Sv9100 And Idt/Net2Phone Setup Guide

    SV9100 Features and Specifications Manual. For details about related hardware, refer to the SV9100 System Hardware Manual. These manuals can be downloaded from NEC’s National Technical Assistance Center (NTAC) web site. You must have a valid dealer ID to access the documents.

  • Page 11: Requirements

    With the SV9100, a VoIP gateway daughter board is required in addition to licensing for IP (SIP) trunks. A minimum of four IP (SIP) trunks are required due to the NEC Communications Server infrastructure setup. The system software for the NEC Communications Server should be Version 06.00.60 or higher.

  • Page 12: Nec Pbx Configuration

    ONFIGURATION ECTION This section provides information to NEC’s solution providers and NEC Associates for configuring an NEC UNIVERGE SV9100 to connect to a IDT/Net2Phone SIP Trunk service provider, utilizing a DYNAMIC configuration. Prerequisites Before you configure the UNIVERGE SV9100, you must have the following information available.

  • Page 13: Table 1 Installation Worksheet

    Issue 1.0 IDT/Net2Phone Table 1 Installation Worksheet WAN Side: Internet Access Type and Speed: WAN IP Address: WAN Subnet Mask: WAN Gateway IP Address: LAN Side: LAN IP Address for SIParator or EdgeMarc: LAN Subnet Mask: LAN IP Address for SV9100: VLAN ID: PBX Information: Model:...

  • Page 14: Sv9100 Programming

    IDT/Net2Phone Issue 1.0 SV9100 P ROGRAMMING ECTION When using IDT/Net2Phone as your SIP trunking service provider, the following programs must be changed for SIP trunking service. When using PCPro or WebPro for programming, enabling an option may be a checkbox option rather than entering a ‘1’ as in terminal programming. Trunk Type / Slot Configuration Figure 1 Blade Configuration SIP Trunking Service Configuration Guide...

  • Page 15: Figure 2 Ipl Dsp Resource Selection

    Issue 1.0 IDT/Net2Phone Figure 2 IPL DSP Resource Selection 10-19-01 : VOIP DSP Resource Selection Specify the operating mode for the DSP resources (0=common use (extensions and trunks), 1=IP extensions only, 2=SIP trunks only, 3=Networking, 4=NetLink, 5=Blocked, 6=Common without Unicast Paging, 7=Multicast, 8=Unicast Paging). SIP Trunking Service Configuration Guide...

  • Page 16: Figure 3 Ip Trunk Availability

    IDT/Net2Phone Issue 1.0 Figure 3 IP Trunk Availability 10-68-1 : IP Trunk Availability – IP Trunk Availability Assign the trunk type as SIP. 10-68-2 : IP Trunk Availability – Start Port Assign the Starting Port for the SIP Trunks. 10-68-3 : IP Trunk Availability –...

  • Page 17: Gcd-Cp10 Network Setup

    Issue 1.0 IDT/Net2Phone GCD-CP10 Network Setup Values shown are for example purposes only. Your actual IP values will be determined by your local LAN administrator. Figure 4 GCD-CP10 Network Setup 10-12-1 : GCD-CP10 Network Setup – IP Address Set the LAN IP address for the system Ethernet port to 192.168.0.10 10-12-2 : GCD-CP10 Network Setup –...

  • Page 18: Voip Dsp License Assignment

    IDT/Net2Phone Issue 1.0 If a router or firewall is placed between the SIP Trunk Provider and SV9100, you must also set the following programs: All routing and forwarding is done by the Starbox Lite router, so NAPT should not be needed in the SV9100.

  • Page 19: Ipl Dsp Basic Setup

    Issue 1.0 IDT/Net2Phone 10-54-2 : Blade License Setup – Quantity Assign the quantity of VoIP DSP Channel Licenses (5103) The License quantity can be found on Feature Activation Page. IPL DSP Basic Setup Values shown are for example purposes only. Your actual IP values will be determined by your local LAN administrator.

  • Page 20: Table 2 Port Table (Udp)

    10020 10275 10020 10531 Table 3 Router Forwarding (Gateway Table) IPLE IP Address RTP Port RTCP Port IPLE Example: Router configuration shown from the NEC InRouter/4300T Router udp;143.101.120.218/255.255.255.0-10020>172.16.0.20-10020 udp;143.101.120.218/255.255.255.0-10021>172.16.0.20-10021 udp;143.101.120.218/255.255.255.0-10052>172.16.0.20-10052 udp;143.101.120.218/255.255.255.0-10053>172.16.0.20-10053 udp;143.101.120.218/255.255.255.0-10084>172.16.0.20-10084 udp;143.101.120.218/255.255.255.0-10085>172.16.0.20-10085 udp;143.101.120.218/255.255.255.0-10116>172.16.0.20-10116 udp;143.101.120.218/255.255.255.0-10117>172.16.0.20-10117 udp;143.101.120.218/255.255.255.0-5060>172.16.0.10-5060 SIP Trunking Service Configuration Guide...

  • Page 21: Sip System Information Setup

    Issue 1.0 IDT/Net2Phone SIP System Information Setup Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 7 SIP System Information Setup 10-28-1 : SIP System Information Setup – Domain Name Define the Domain name up to 64 characters. This information is specific to your market and is provided by your SIP Trunking Service Provider.

  • Page 22: Sip Server Information Setup

    IDT/Net2Phone Issue 1.0 SIP Server Information Setup Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 8 SIP Server Information Setup SIP Trunking Service Configuration Guide...
  • Page 23 Issue 1.0 IDT/Net2Phone 10-29-01 : SIP Server Information Setup – Outbound Default Proxy Enable (1) the SIP Outbound Proxy. If entries are made in Program 10-29-xx for a SIP Server and the SIP Server is then removed or not used, the entries in Program 10-29-xx must be set back to their default settings. Even if 10-29-01 is set to .0.

  • Page 24: Sip Trunk Registration Information

    IDT/Net2Phone Issue 1.0 SIP Trunk Registration Information Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 9 SIP Trunk Registration Information 10-36-1 : SIP Trunk Registration Information – Registration Registration is enabled for this testing. 10-36-2 : SIP Trunk Registration Information –...

  • Page 25: Ip System Interconnection Setup

    Issue 1.0 IDT/Net2Phone IP System Interconnection Setup Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 10 IP System Interconnection Setup 10-23-1 : System Interconnection Enable interconnection to the SIP Server. 10-23-2 : IP Address Enter the IP Address of the SIP Server.

  • Page 26: Calling Party Information (Trunk)

    IDT/Net2Phone Issue 1.0 Calling Party Information (Trunk) Caller ID - In the Invite message there are two fields that can have caller ID. One field is the “SIP From Address” and the other field is “SIP Display Info”. If both of these fields are left blank the call will not complete.

  • Page 27: Class Of Service Options (Outgoing Call Service)

    Issue 1.0 IDT/Net2Phone 3.10 Class of Service Options (Outgoing Call Service) Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 11 Class of Service Options (Outgoing Call Service) 20-08-13 : Class of Service Options (Outgoing Call Service) – ISDN Clip This needs to be turned ON per COS, if you are trying to send any information on a per station basis.

  • Page 28: Ip Trunk Calling Party Number Setup

    IDT/Net2Phone Issue 1.0 3.11 IP Trunk Calling Party Number Setup Figure 12 IP Trunk (H.323/SIP) Calling Party Number Setup for Trunks 21-17-01: Calling Party Number Setup for Trunks On a per trunk basis this populates the “SIP Display Info” field. If a station has a setting in 21-19-01, it will override this field.

  • Page 29: 21-19-01 : Ip Trunk (Sip) Calling Party Number Setup For Extensions

    Issue 1.0 IDT/Net2Phone 3.12 IP Trunk (SIP) Calling Party Number Setup for Extensions Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 13 Trunk (SIP) Calling Party Number Setup for Extensions 21-19-01 : IP Trunk (SIP) Calling Party Number Setup for Extensions On a per station basis this populates the “SIP Display Info”...

  • Page 30: Did (Tn To Ext Map)

    IDT/Net2Phone Issue 1.0 3.13 DID (TN to ext map) Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 14 Incoming Call Trunk Setup 22-02-01 : Incoming Call Trunk Setup Define the SIP trunks as type 3 (DID). In addition to the SIP trunk programming, refer to the DID feature in the SV9100 Features and Specifications Manual for additional DID programming (e.g., 14-05, 22-04, 22-09, 22-10, 22-11, 22-12, 22-13, 22-17, 34-01).

  • Page 31: Sip Trunk Codec Setup

    Issue 1.0 IDT/Net2Phone 3.14 SIP Trunk CODEC Setup Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 15 SIP Trunk Codec Information Basic Setup 84-13-28 : SIP Trunk CODEC Setup – Audio Capability Priority Set the priority to G.729_PT SIP Trunking Service Configuration Guide...

  • Page 32: Tos Setup

    IDT/Net2Phone Issue 1.0 3.15 ToS Setup Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 16 ToS Setup 84-10-01 : ToS Setup – ToS Mode For the RTP/RTCP (Protocol type 5) and SIP Trunk (Protocol type 9), set the ToS Mode to “2”...

  • Page 33: Sip Trunk Basic Setup

    Issue 1.0 IDT/Net2Phone 3.16 SIP Trunk Basic Setup Values shown are for example purposes only. Your actual values will be determined by your implementation team. Figure 17 SIP Trunk Basic Setup 84-14-11 : SIP Trunk Basic Setup – URL/TO Header Setting Information Set this program to Proxy Server Domain.

  • Page 34: Figure 18 Fax Over Ip Setup

    IDT/Net2Phone Issue 1.0 Figure 18 FAX over IP Setup 84-33-01: FAX over IP Setup – Fax Relay Mode Set this Program to Enable for SIP Trunk for FAX testing. (FAX is not tested for this Testing) This setting is not applicable for this carrier test. SIP Trunking Service Configuration Guide...

  • Page 35: Figure 19 Voipdb Dtmf Setup - Dtmf Relay Mode

    Issue 1.0 IDT/Net2Phone Figure 19 VoIPDB DTMF Setup - DTMF Relay Mode 84-34-01: VoIPDB DTMF Setup – DTMF Relay Mode Set this to RFC2833 for SIP Trunk. SIP Trunking Service Configuration Guide...

  • Page 36: Initial Testing And Troubleshooting

    IDT/Net2Phone Issue 1.0 NITIAL ESTING AND ROUBLESHOOTING ECTION To confirm that the system is correctly set, perform the following tests: If you run into an issue with any of these tests, refer to Table 4 Troubleshooting Guide. Test an outgoing call to a local number. Check for ringback, 2-way audio and quality. Test an outgoing call to a long distance number.
  • Page 37 Issue Cause Remedy Router Configuration Check Router Configuration No Calls IN/Out NEC Configuration Check NEC Configuration Unqualified IP Address Note WAN IP Address and Contact Provider NEC Configuration Check NEC Configuration No Calls Out Unqualified IP Address Note WAN IP Address and Contact Provider...

Table of Contents