Related Manuals for Vaillant ecoVIT exclusiv VKK 226/4-H
Summary of Contents for Vaillant ecoVIT exclusiv VKK 226/4-H
-
Page 1: Operating Instructions
Operating instructions ecoVIT exclusiv VKK 226/4 – VKK 656/4 AT, DE Publisher/manufacturer Vaillant GmbH Berghauser Str. 40 D-42859 Remscheid Tel. +49 21 91 18‑0 Fax +49 21 91 18‑2810 [email protected] www.vaillant.de... -
Page 2: Table Of Contents
Contents Contents Safety ..............3 Action-related warnings ......... 3 Intended use ............3 General safety information ........3 Notes on the documentation ......5 Observing other applicable documents ....5 Storing documents..........5 Validity of the instructions ........5 Product description..........5 Design of the product.......... -
Page 3: Safety
Safety 1 not be carried out by children unless they are Safety supervised. Action-related warnings Any other use that is not specified in these Classification of action-related warnings instructions, or use beyond that specified in The action-related warnings are classified in this document shall be considered improper accordance with the severity of the possible use. - Page 4 1 Safety ▶ Alert the police and fire brigade as soon as 1.3.8 Risk of corrosion damage due to unsuitable combustion and room air you are outside the building. ▶ Use a telephone outside the building to Sprays, solvents, chlorinated cleaning inform the emergency service department agents, paint, adhesives, ammonia com- of the gas supply company.
-
Page 5: Notes On The Documentation
Notes on the documentation 2 Notes on the documentation Product description Observing other applicable documents Design of the product ▶ You must observe all operating instructions enclosed with the system components. Storing documents ▶ Keep this manual and all other applicable documents safe for future use. - Page 6 3 Product description Control (accessory) Reset button Symbol Meaning Explanation Main switch Heating flow temperat- comDIALOG The heating flow and do- ure rotary knob mestic hot water temper- + button Cylinder temperature ature are specified via − button rotary knob the comDIALOG com- munications system.
-
Page 7: Frost Protection Function
Operation 4 Frost protection function Starting up the product 4.2.1 Opening the isolator devices The product is equipped with a frost protection function. If the heating flow temperature falls below 5 °C when the Ask the competent person who installed the product to main switch is on, the product starts up and heats the cir- explain to you where these isolator devices are located culating water to approx. -
Page 8: Setting The Language
4 Operation 4.2.3 Switching off the product Note To ensure that the control can set temper- atures up to the maximum heating flow temperature, the rotary knob for the heating flow temperature should always be set to the clockwise end stop. Conditions: No control connected Main switch Display... -
Page 9: Setting The Cylinder Temperature
Operation 4 Setting the cylinder temperature Position Meaning Temperature 15 ℃ Fully left Minimum cylinder Conditions: Control connected temperature = frost protection ≈ 50 ℃ Centre Medium cylinder temperature 65 ℃ Fully right Maximum cylinder temperature Switching off the functions 4.6.1 Switching off heating mode Note... -
Page 10: Status Code Meanings
5 Care and maintenance 4.6.3 Switching off cylinder charging mode Guaranteeing the correct filling pressure of (without control) the heating installation ▶ 5.3.1 Checking the system pressure Turn the rotary knob for the cylinder temperature to the anti-clockwise end stop. ◁... -
Page 11: Checking The Condensate Discharge Pipe And Tundish
Care and maintenance 5 5.3.2 Filling the heating installation Caution. Risk of material damage due to heating water that is extremely calciferous or cor- rosive or contaminated by chemicals. Unsuitable tap water damages the seals and diaphragms, blocks components in the product and heating installation through which the water flows and causes noise. -
Page 12: Troubleshooting
6 Troubleshooting ▶ – Immersion depth: ≈ 80 mm If no control is present when a main switch has been switched on, set the rotary Take measurements in the air route on the combustion air test opening (2). knobs for the target heating flow and –... -
Page 13: Permanently Decommissioning The Product
Recycling and disposal 8 Permanently decommissioning the product ▶ Have a competent person permanently decommission the product. Recycling and disposal ▶ The competent person who installed your product is re- sponsible for the disposal of the packaging. If the product is identified with this symbol: ▶... -
Page 14: Appendix
Appendix Appendix Status codes Note Since the code table is used for various products, some codes may not be visible for the product in question. Statuscode Meaning S.00 Heating: No heat de- Heating has no heat demand. The burner is off. mand S.01 Heating mode: Fan start- The fan start-up for heating mode is activated. - Page 15 Appendix Symptom Possible cause Measure No hot water, heating stays cold Fault during the ignition pro- Check whether the gas stopcock is open. cess. F.28 "No ignition during If the gas stopcock is closed, open the gas stopcock with the start-up"...
- Page 16 0020258609_00 0020258609_00 24.05.2017 Supplier Vaillant Deutschland GmbH & Co.KG Berghauser Str. 40 D-42859 Remscheid Telefon 021 91 18‑0 Telefax 021 91 18‑2810 Auftragsannahme Vaillant Kundendienst 021 91 5767901 [email protected] www.vaillant.de © These instructions, or parts thereof, are protected by copyright and may be reproduced or distributed only with the manufacturer's written consent.