Mitsubishi fx2nc-485adp Manual
  1. Manuals
  2. Brands
  3. Mitsubishi Manuals
  4. Controller
  5. FX2NC-485ADP
  6. Manual
Mitsubishi fx2nc-485adp Manual

Mitsubishi fx2nc-485adp Manual

Fx series
Show thumbs Also See for fx2nc-485adp:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Table of Contents

Quick Links

See also: User Manual, Installation Manual
FX Series Computer Link
Driver
1
System Configuration....................................................................................................... 3
2
Selection of External Device ............................................................................................ 7
3
Example of Communication Setting ................................................................................. 8
4
Setup Items .................................................................................................................... 15
5
Cable Diagram ............................................................................................................... 20
6
Supported Device........................................................................................................... 35
7
Device Code and Address Code.................................................................................... 37
8
Error Messages.............................................................................................................. 38
1
Mitsubishi Electric Corporation
Table of Contents
loading

Related Manuals for Mitsubishi fx2nc-485adp

Summary of Contents for Mitsubishi fx2nc-485adp

  • Page 1: Table Of Contents

    Mitsubishi Electric Corporation FX Series Computer Link Driver System Configuration....................... 3 Selection of External Device .................... 7 Example of Communication Setting ................. 8 Setup Items ........................15 Cable Diagram ....................... 20 Supported Device......................35 Device Code and Address Code..................37...

  • Page 2: Cable Diagram

    FX Series Computer Link Driver Introduction This manual describes how to connect Display and External Device (target PLC). In this manual, the connection procedure will be described by following the below sections: System Configuration "1 System Configuration" (page 3) This section shows the types of External Device which can be connected and SIO type.

  • Page 3: System Configuration

    FX Series Computer Link Driver System Configuration The system configuration in the case when the External Device of Mitsubishi Electric Corp. and the display are connected is shown. Series Link I/F SIO Type Setting Example Cable Diagram Setting Example 1...

  • Page 4: Cable Diagram

    FX Series Computer Link Driver Series Link I/F SIO Type Setting Example Cable Diagram *When using channel 1 (Ch1) FX3U-232ADP Setting Example 1 Cable Diagram 1 RS232C (page 8) (page 20) *When using channel 2 (Ch2) FX3U-232ADP +FX3U- FX3UC (D,DSS) *When using channel 1 (Ch1) RS422/485 Setting Example 3...
  • Page 5 FX Series Computer Link Driver IPC COM Port When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please refer to the IPC manual for details. Usable port Usable Port Series RS-232C RS-422/485(4 wire) RS-422/485(2 wire) COM1...
  • Page 6 FX Series Computer Link Driver DIP switch setting: RS-422/485 (4 wire) DIP switch Setting Description Reserved (always OFF) SIO type: RS-422/485 Output mode of SD (TXD) data: Always output Terminal resistance (220Ω) insertion to SD (TXD): None Terminal resistance (220Ω) insertion to RD (RXD): None Short-circuit of SDA (TXA) and RDA (RXA): Not available Short-circuit of SDB (TXB) and RDB (RXB): Not available RS (RTS) Auto control mode: Disabled...

  • Page 7: Selection Of External Device

    Select the External Device to be connected to the Display. Setup Items Setup Description Select the maker of External Device to be connected. Select "Mitsubishi Electric Maker Corporation". Select a model (series) of External Device to be connected and connection method.

  • Page 8: Example Of Communication Setting

    FX Series Computer Link Driver Example of Communication Setting Examples of communication settings of the display and the External Device, recommended by Pro-face, are shown. When you use the FX Series, use GP-Pro EX and the ladder software to set as below. Setting Example 1 Setting of GP-Pro EX Communication Settings...
  • Page 9 FX Series Computer Link Driver Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings ]. When you connect multiple External Devices, click from [Device-Specific Settings] of [Device/PLC Settings] to add another External Device.
  • Page 10 FX Series Computer Link Driver Setting of External Device Setting of External Device includes the setting with parameter and the setting by writing data to the special data register. Setting with parameter Double-click [PC parameter] from [Parameter] in the tree view of the ladder software to display the [FX parameter] dialog box.
  • Page 11 FX Series Computer Link Driver Setting Example 2 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace. Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ].
  • Page 12 FX Series Computer Link Driver Setting of External Device Setting of External Device includes the setting with parameter and the setting by writing data to the special data register. Setting with Parameter Double-click [PC parameter] from [Parameter] in the tree view of the ladder software to display the [FX parameter] dialog box.
  • Page 13 FX Series Computer Link Driver Setting Example 3 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace. Device Setting To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific Settings ] of [Device/PLC Settings ].
  • Page 14 FX Series Computer Link Driver Setting of External Device Setting of External Device includes the setting with parameter and the setting by writing data to the special data register. Setting with Parameter Double-click [PC parameter] from [Parameter] in the tree view of the ladder software to display the [FX parameter] dialog box.

  • Page 15: Setup Items

    FX Series Computer Link Driver Setup Items Set communication settings of the Display with GP-Pro EX or in off-line mode of Display. The setting of each parameter must be identical to that of External Device. "3 Example of Communication Setting" (page 8) Setup Items in GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings ] from [System setting window] in workspace.
  • Page 16 FX Series Computer Link Driver Setup Items Setup Description Use an integer from 0 to 255 to enter standby time (ms) for Display from receiving packets to transmitting next commands. Wait To Send • Set the value more than twice as the scanning time of External Device when connecting to FX0N, FX1S, FX1N and FX1NC Series.
  • Page 17 FX Series Computer Link Driver Setup Items in Off-Line Mode • Refer to the Maintenance/Troubleshooting manual for information on how to enter off-line mode or about the operation. Maintenance/Troubleshooting Manual "2.2 Off-line Mode" Communication Settings To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings] in off-line mode. Touch the External Device you want to set from the displayed list.
  • Page 18 FX Series Computer Link Driver Setup Items Setup Description Use an integer from 0 to 255 to enter standby time (ms) for Display from receiving packets to transmitting next commands. Wait To Send Set the value more than twice as the scanning time of External Device when connecting to FX0N, FX1S, FX1N and FX1NC Series.
  • Page 19 FX Series Computer Link Driver Option To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings]. Touch the External Device you want to set from the displayed list, and touch [Option]. Setup Items Setup Description You can switch RI/VCC of the 9th pin when you select RS232C for SIO type. RI/VCC It is necessary to change RI/5V by changeover switch of IPC when connect with IPC.

  • Page 20: Cable Diagram

    FX Series Computer Link Driver Cable Diagram The cable diagram shown below may be different from the cable diagram recommended by Mitsubishi Electric Corp. Please be assured there is no operational problem in applying the cable diagram shown in this manual.
  • Page 21 FX Series Computer Link Driver Cable Diagram 2 Display Cable Notes (Connection Port) GP (COM1) ST (COM1) Your own cable The cable length must be 15 meters or less. PC/AT Only the COM port which can communicate by RS-232C can be used. IPC COM Port (page 5) External Device D-sub 9 pin (socket)
  • Page 22 All GP models except GP-3200 series and AGP-3302B • The shield of cables connected to FX2N-485-BD, FX1N-485-BD, FX2NC-485ADP and FX3U- 485ADP must be D-class grounded. • Connect the shield of cable connected to FX0N-485ADP to the adapter FG terminal. In addition, always connect the FG terminal of FX0N-485ADP to the ground terminal of External Device body with D-class grounded.
  • Page 23 FX Series Computer Link Driver A ) When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face and your own cable • 1:1 connection Terminal block conversion adapter Terminal block Shield (Terminal block) on External Device Termination Signal name...
  • Page 24 FX Series Computer Link Driver B) When making your own cable • 1:1 connection Terminal block Shield on External Device D-sub 9 pin (socket) Termination Termination Signal name Signal name resistance resistance 330Ω 1/4W 330Ω 1/4W Display Shell • 1:n connection Terminal block Terminal block on External Device...
  • Page 25 FX Series Computer Link Driver C) When using the online adapter (CA4-ADPONL-01), the connector terminal block conversion adapter (CA3- ADPTRM-01) by Pro-face and your own cable • 1:1 connection Terminal block Terminal block conversion adapter on External Device (Terminal block) Shield Termination Termination...
  • Page 26 FX Series Computer Link Driver D)When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable • 1:1 connection Terminal block D-sub 9 pin (plug) Shield on External Device Termination Termination Signal name Signal name resistance resistance 330Ω 1/4W 330Ω...
  • Page 27 FX Series Computer Link Driver Cable Diagram 4 Display Cable Notes (Connection Port) COM port conversion adapter by Pro-face CA3-ADPCOM-01 (COM1) Connector terminal block conversion adapter The cable length must be AGP-3302B (COM2) by Pro-face 500 meters or less. (COM2) CA3-ADPTRM-01 Your own cable Your own cable...
  • Page 28 FX Series Computer Link Driver • The shield of cables connected to FX2N-485-BD, FX1N-485-BD, FX2NC-485ADP and FX3U- 485ADP must be D-class grounded. • Connect the shield of cable connected to FX0N-485ADP to the adapter FG terminal. In addition, always connect the FG terminal of FX0N-485ADP to the ground terminal of External Device body with D-class grounded.
  • Page 29 FX Series Computer Link Driver A) When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face and your own cable • 1:1 connection Terminal block Terminal block conversion adapter Shield on External Device (Terminal block) Signal name Signal name...
  • Page 30 FX Series Computer Link Driver B) When making your own cable • 1:1 connection Terminal block D-sub 9 pin (socket) Shield on External Device Signal Signal Termination name name resistance 110Ω 1/2W Termination resistance 110Ω 1/2W Display Shell • 1:n connection Terminal block Terminal block D-sub 9 pin (socket)
  • Page 31 FX Series Computer Link Driver C) When using the online adapter (CA4-ADPONL-01), the connector terminal block conversion adapter (CA3- ADPTRM-01) by Pro-face and your own cable • 1:1 connection Terminal block conversion adapter Terminal block Shield (Terminal block) on External Device Signal name Signal name Termination...
  • Page 32 FX Series Computer Link Driver D)When using the online adapter (CA4-ADPONL-01) by Pro-face and your own cable • 1:1 connection Terminal block D-sub 9 pin (plug) on External Device Shield Signal name Signal name Display Termination resistance 110Ω 1/2W CA4-ADPONL-01 TERMRX Shell Your own cable...
  • Page 33 FX Series Computer Link Driver E) When using the COM port conversion adapter (CA3-ADPCOM-01), the connector terminal block conversion adapter (CA3-ADPTRM-01) by Pro-face and your own cable • 1:1 connection Terminal block Terminal block conversion adapter Shield on External Device (Terminal block) Signal name Signal name...
  • Page 34 FX Series Computer Link Driver F) When making your own cable • 1:1 connection Terminal block D-sub 9 pin (socket) on External Device Shield Signal Signal Termination name name resistance 110Ω 1/2W DATA+ Termination DATA- resistance Display 110Ω 1/2W GND(SG) Shell •...

  • Page 35: Supported Device

    FX Series Computer Link Driver Supported Device Range of supported device address is shown in the table below. Please note that the actually supported range of the devices varies depending on the External Device to be used. Please check the actual range in the manual of your External Device.
  • Page 36 FX Series Computer Link Driver • Please refer to the GP-Pro EX Reference Manual for system data area. Cf. GP-Pro EX Reference Manual "Appendix 1.4 LS Area (Direct Access Method)" • Please refer to the precautions on manual notation for icons in the table. "Manual Symbols and Terminology"...

  • Page 37: Device Code And Address Code

    FX Series Computer Link Driver Device Code and Address Code Use device code and address code when you select "Device Type & Address" for the address type in data displays. Device Code Device Device Name Address Code (HEX) Value of word address divided Input Relay 0080 by 0x10...

  • Page 38: Error Messages

    FX Series Computer Link Driver Error Messages Error messages are displayed on the screen of Display as follows: "No. :Device Name:Error Message(Error Occurrence Area)". Each description is shown below. Item Description Error No. Name of External Device where error occurs.Device name is a title of External Device set Device Name with GP-Pro EX.(Initial value [PLC1]) Error Message...

Table of Contents