Table of Contents
Quick Links
Cautions on Safety
(Make sure to read this paragraph before using the unit.)
Thoroughly read this manual, a separate USER'S MANUAL and all attached documents of the connected
programmable controller (hereafter referred to as "PLC") and other related units before starting installation,
operation and inspection/maintenance of the temperature control block. Acquire the knowledge on
equipment, the information on safety and all cautions before using the temperature control block.
In this instruction manual, cautions on safety are classified as "DANGER" or "CAUTION".
This symbol indicates that incorrect handling may generate a dangerous situation which may lead
to death or serious injury.
This symbol indicates that incorrect handling may generate a dangerous situation which may lead
to medium or minor injury or physical damage.
Even an item classified as "CAUTION" may lead to a severe result depending on the situation.
Each item describes important information. Make sure to observe each item marked with "DANGER" or
"CAUTION".
Carefully store the instruction manual offered together with the temperature control block so that the
operator can refer to it at any time necessary. Make sure to deliver the instruction manual to the end user.
We appreciate it very much that you have purchased the temperature control block FX
programmable controller.
This manual describes handling of the MELSEC-F Series Temperature Control Block FX
Thoroughly read this manual and other manuals of related products, and sufficiently understand the
specifications before use.
Make sure to deliver this manual to the end user.
Brand and product names described by/in this manual are trademarks or registered trademark of the
irrespective ownes.
Related Manuals
When you using the FX
Make sure to obtain the USER'S MANUAL from the dealer from which you have purchased the FX
2LC, and safely use the FX
Manual name
FX
-2LC
2N
USER'S MANUAL
FX
2N
HARDWARE MANUAL
FX
2NC
HARDWARE MANUAL
FX
Series
3U
HARDWARE MANUAL
FX
Series
3U
User's Manual
- Hardware Edition
FX SERIES
PROGRAMMING
MANUAL ΙΙ
FX
/FX
Series
3U
3UC
Programming Manual
- Basic & Applied
Instruction Edition
If necessary, obtain them from the dealer from which you have purchased the FX
-2LC for the first time, a separate FX
2N
-2LC.
2N
Manual No.
separately supplied
JY992D85601
Additional Manual
JY992D66301 Supplied with product
JY992D76401 Supplied with product
JY997D18801 Supplied with product
JY997D16501
Additional Manual
JY992D88101
Additional Manual
JY997D16601
Additional Manual
FX
-2LC SPECIAL FUNCTION BLOCK
2N
USER'S GUIDE
-2LC USER'S MANUAL is required.
2N
Supplied with
product or
Describes the specification, wiring,
installation of FX
Describes the specification, wiring
and installation of FX
Describes the specification, wiring
and installation of FX
Describes the specification, wiring
and installation of FX
Describes the specification, wiring
and installation of FX
Describes the instructions of FX
FX
This manual explains the installations
of FX
JY992D85601C
-2LC for Mitsubishi
2N
2N
Description
-2LC.
2N
2N
2NC
3U
3U
/FX
/FX
series PLC.
1N
2N
2NC
/FX
series PLC.
3U
3UC
-2LC.
2N
-2LC.
-
2N
series PLC.
series PLC.
series PLC.
series PLC.
/
1S
Table of Contents
Related Manuals for Mitsubishi FX2N-2LC
Summary of Contents for Mitsubishi FX2N-2LC
- Page 1 Make sure to deliver the instruction manual to the end user. We appreciate it very much that you have purchased the temperature control block FX -2LC for Mitsubishi programmable controller. This manual describes handling of the MELSEC-F Series Temperature Control Block FX -2LC.
-
Page 2: Outline Of Product
1. Outline of Product Cautions on design • Install a safety circuit outside the PLC so that the entire system conservatively operates even if an abnormality occurs in the external power supply or a failure occurs in the PLC. If the safety circuit is installed inside the PLC, malfunction and erroneous output may cause accidents. -
Page 3: Installation Method
3. Installation Method Cautions on installation • Use the unit in the environment for the general specifications described in the manual. Never use the unit in a place with dust, soot, conductive dust, corrosive gas or flammable gas, a place exposed to high temperature, dew condensation or rain and wind or a place exposed to vibration or impact. -
Page 4: Cautions On Wiring
5. Wiring Cautions on wiring • Make sure to shut down the power supplies of all phases on the outside before starting installation or wiring. If the power supplies are not shut down, you may receive an electrical shock or the unit may be damaged. -
Page 5: Performance Specifications
6.3 Performance specifications Item Description Control method Two-position control, PID control (with auto tuning function), PI control Control operation 500ms period Set temperature Equivalent to input range range Heater disconnection Alarm is detected by buffer memory detection (Variable within range from 0.0 to 100.0 A.). 0: Measured value monitor 1: Measured value monitor + Temperature alarm Operation mode... -
Page 6: Output Specifications
• All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples. - Page 7 -2LC is connected to the Series PLC. We appreciate it very much that you have purchased the temperature control block FX -2LC for Mitsubishi (The FX -2LC performs arithmetic operation for PID control and output control. The PLC does not programmable controller.
- Page 8 All examples and diagrams shown in this manual are intended only as an aid to understanding tightening torque of 0.5 to 0.8N m the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual Larger one between ± 5% of input value and 2 A Measurement precision use of the product based on these illustrative examples.