Page 1 GE Digital Energy LISTED 650 Markland Street IND.CONT. EQ. 52TL Markham, Ontario GE Multilin's Quality Management Canada L6C 0M1 System is registered to ISO 9001:2008 Tel: +1 905 927 7070 Fax: +1 905 927 5098 QMI # 005094 UL # A3775 Internet: http://www.GEDigitalEnergy.com...
Page 2 The contents of this manual are the property of GE Multilin Inc. This documentation is furnished on license and may not be reproduced in whole or in part without the permission of GE Multilin. The content of this manual is for informational use only and is subject to change without notice.
Page 3: Table Of Contents
3.2.2 DIELECTRIC STRENGTH ................. 3-9 3.2.3 CONTROL POWER ................... 3-9 3.2.4 CT/VT MODULES .................... 3-10 3.2.5 PROCESS BUS MODULES ................3-12 3.2.6 CONTACT INPUTS AND OUTPUTS ............... 3-12 3.2.7 TRANSDUCER INPUTS/OUTPUTS ..............3-21 GE Multilin F35 Multiple Feeder Protection System...
Page 4 USER-PROGRAMMABLE LEDS ..............5-59 5.2.13 USER-PROGRAMMABLE SELF TESTS ............5-63 5.2.14 CONTROL PUSHBUTTONS ................5-64 5.2.15 USER-PROGRAMMABLE PUSHBUTTONS............5-65 5.2.16 FLEX STATE PARAMETERS ................5-71 5.2.17 USER-DEFINABLE DISPLAYS ................5-71 5.2.18 DIRECT INPUTS/OUTPUTS ................5-74 5.2.19 TELEPROTECTION ..................5-81 5.2.20 INSTALLATION ....................5-82 F35 Multiple Feeder Protection System GE Multilin...
Page 5 5.9.1 DCMA INPUTS ....................5-206 5.9.2 RTD INPUTS....................5-207 5.9.3 DCMA OUTPUTS ..................5-209 5.10 TESTING 5.10.1 TEST MODE ....................5-213 5.10.2 FORCE CONTACT INPUTS ................5-214 5.10.3 FORCE CONTACT OUTPUTS ..............5-215 GE Multilin F35 Multiple Feeder Protection System...
Page 6 7.2 TARGETS 7.2.1 TARGETS MENU ....................7-5 7.2.2 TARGET MESSAGES ..................7-5 7.2.3 RELAY SELF-TESTS ..................7-5 8. SECURITY 8.1 USER ACCOUNTS 8.1.1 OVERVIEW ......................8-1 8.1.2 ENABLING THE SECURITY MANAGEMENT SYSTEM........8-1 8.1.3 ADDING A NEW USER ..................8-1 F35 Multiple Feeder Protection System GE Multilin...
Page 7 STORE MULTIPLE SETTINGS (FUNCTION CODE 10H) ........B-6 B.2.6 EXCEPTION RESPONSES ................B-6 B.3 FILE TRANSFERS B.3.1 OBTAINING RELAY FILES VIA MODBUS ............B-7 B.4 MEMORY MAPPING B.4.1 MODBUS MEMORY MAP .................B-9 B.4.2 DATA FORMATS .....................B-69 GE Multilin F35 Multiple Feeder Protection System...
Page 8 DNP V3.00 DEVICE PROFILE ................E-1 E.1.2 IMPLEMENTATION TABLE ................E-4 E.2 DNP POINT LISTS E.2.1 BINARY INPUT POINTS ................... E-8 E.2.2 BINARY AND CONTROL RELAY OUTPUT............E-9 E.2.3 COUNTERS..................... E-10 E.2.4 ANALOG INPUTS.................... E-11 viii F35 Multiple Feeder Protection System GE Multilin...
Page 9 TABLE OF CONTENTS F. MISCELLANEOUS F.1 CHANGE NOTES F.1.1 REVISION HISTORY ..................F-1 F.1.2 CHANGES TO THE MANUAL ................F-2 F.2 ABBREVIATIONS F.2.1 STANDARD ABBREVIATIONS ................. F-5 F.3 WARRANTY F.3.1 GE MULTILIN WARRANTY ................F-7 GE Multilin F35 Multiple Feeder Protection System...
Page 10 TABLE OF CONTENTS F35 Multiple Feeder Protection System GE Multilin...
Page 11: Getting Started
Class 1M devices are considered safe to the unaided eye. Do not view directly with optical instruments. This product is rated to Class A emissions levels and is to be used in Utility, Substation Industrial environments. Not to be used near electronic devices rated for Class B levels. GE Multilin F35 Multiple Feeder Protection System...
Page 12: Inspection Procedure
For product information, instruction manual updates, and the latest software updates, visit the GE Digital Energy website at http://www.gedigitalenergy.com. If there is any noticeable physical damage, or any of the contents listed are missing, please contact GE Digital Energy immediately.
Page 13: Ur Overview
This new generation of equipment is easily incorporated into automation systems, at both the station and enterprise levels. The GE Multilin Uni- versal Relay (UR) series meets these goals.
Page 14 The UR-series devices operate in a cyclic scan fashion. The device reads the inputs into an input status table, solves the logic program (FlexLogic equation), and then sets each output to the appropriate state in an output status table. Any result- ing task execution is priority interrupt-driven. Figure 1–3: UR-SERIES SCAN OPERATION F35 Multiple Feeder Protection System GE Multilin...
Page 15: Software Architecture
5. An explanation of the use of inputs from CTs and VTs is in the Introduction to AC sources section in chapter 5. A description of how digital signals are used and routed within the relay is contained in the Introduction to FlexLogic section in chapter 5. GE Multilin F35 Multiple Feeder Protection System...
Page 16: Enervista Ur Setup Software
PCTEL 2304WT V.92 MDC internal modem 1.3.2 INSTALLATION After ensuring the minimum requirements for using EnerVista UR Setup are met (previous section), install the EnerVista UR Setup from the GE EnerVista CD. Or download the UR EnerVista software from http://www.gedigitalenergy.com/multilin and install it.
Page 17: Configuring The F35 For Software Access
EnerVista UR Setup software. The F35 can also be accessed locally with a computer through the front panel RS232 port or the rear Ethernet port using the Quick Connect feature. • To configure the F35 for remote access via the rear RS485 port, see the Configuring Serial Communications section. GE Multilin F35 Multiple Feeder Protection System...
Page 18 A computer with an RS232 port and a serial cable is required. To use the RS485 port at the back of the relay, a GE Multilin F485 converter (or compatible RS232-to-RS485 converter) is required. See the F485 instruction manual for details.
Page 19 UR device must be on the same subnet. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista CD or online from http://www.gedigitalenergy.com/multilin). See the Software Installation section for installation details.
Page 20: Using The Quick Connect Feature
Before starting, verify that the serial cable is properly connected from the computer to the front panel RS232 port with a straight-through 9-pin to 9-pin RS232 cable. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista CD or online from http://www.gedigitalenergy.com/multilin). See the Software Installation section if not already installed.
Page 21 Now, assign the computer an IP address compatible with the relay’s IP address. From the Windows desktop, right-click the My Network Places icon and select Properties to open the network con- nections window. Right-click the Local Area Connection icon and select Properties. GE Multilin F35 Multiple Feeder Protection System 1-11...
Page 22 Minimum = 0ms, Maximum = 0ms, Average = 0 ms Note that the values for vary depending on local network configuration. time If the following sequence of messages appears when entering the command: C:\WINNT>ping 1.1.1.1 1-12 F35 Multiple Feeder Protection System GE Multilin...
Page 23 Default Gateway ..: C:\WINNT> It can be necessary to restart the computer for the change in IP address to take effect (Windows 98 or NT). GE Multilin F35 Multiple Feeder Protection System 1-13...
Page 24 From the Windows desktop, right-click the My Network Places icon and select Properties to open the network con- nections window. Right-click the Local Area Connection icon and select the Properties item. Select the Internet Protocol (TCP/IP) item from the list provided and click the Properties button. 1-14 F35 Multiple Feeder Protection System GE Multilin...
Page 25: Connecting To The F35 Relay
Device Setup menu. This feature allows the user to identify and interrogate all UR-series devices at a loca- tion. 1.3.5 CONNECTING TO THE F35 RELAY When unable to connect because of an "ACCESS VIOLATION," access Device Setup and refresh the order code for the device. GE Multilin F35 Multiple Feeder Protection System 1-15...
Page 26 View the last recorded oscillography record • View the status of all F35 inputs and outputs • View all of the F35 metering values • View the F35 protection summary • Generate a service report 1-16 F35 Multiple Feeder Protection System GE Multilin...
Page 27: Ur Hardware
Figure 1–7: RELAY COMMUNICATION OPTIONS To communicate through the F35 rear RS485 port from a computer RS232 port, the GE Multilin RS232/RS485 converter box is required. This device (catalog number F485) connects to the computer using a straight-through serial cable. A shielded twisted-pair (20, 22, or 24 AWG) connects the F485 converter to the F35 rear communications port.
Page 28: Using The Relay
To put the relay in the “Programmed” state, press either of the VALUE keys once and then press ENTER. The face- plate Trouble LED turns off and the In Service LED turns on. 1-18 F35 Multiple Feeder Protection System GE Multilin...
Page 29: Relay Passwords
See the Changing Settings section in Chapter 4 for complete instructions on setting security-level passwords. 1.5.6 FLEXLOGIC CUSTOMIZATION NOTE FlexLogic equation editing is required for setting user-defined logic for customizing the relay operations. See the FlexLogic section in Chapter 5. GE Multilin F35 Multiple Feeder Protection System 1-19...
Page 30: Commissioning
Unscheduled maintenance, such as a disturbance causing system interruption: View the event recorder and oscillography or fault report for correct operation of inputs, outputs, and elements. If it is concluded that the relay or one of its modules is of concern, contact GE Multilin for service. 1-20...
Page 31: Product Description
Phase time overcurrent Thermal overload protection Negative-sequence time overcurrent 50DD Disturbance detector AC circuit breaker Ground instantaneous overcurrent Neutral overvoltage Neutral instantaneous overcurrent Auxiliary overvoltage Phase instantaneous overcurrent Autoreclose 50_2 Negative-sequence instantaneous overcurrent Underfrequency GE Multilin F35 Multiple Feeder Protection System...
Page 32: Ordering
Each of these modules can be supplied in a number of configurations specified at the time of ordering. The information required to completely specify the relay is provided in the following tables (see chapter 3 for full details of relay modules). Order codes are subject to change without notice. See the GE Multilin ordering page at http://www.gedigitalenergy.com/multilin/order.htm for the latest options.
Page 33 Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel RS422, 2 Channels GE Multilin F35 Multiple Feeder Protection System...
Page 34 Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel RS422, 2 Channels F35 Multiple Feeder Protection System GE Multilin...
Page 35 Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel RS422, 2 Channels GE Multilin F35 Multiple Feeder Protection System...
Page 36 Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, LASER Channel 1 - G.703; Channel 2 - 1300 nm, single-mode LASER G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel RS422, 2 Channels F35 Multiple Feeder Protection System GE Multilin...
Page 37: Replacement Modules
4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed) 8 RTD inputs INPUTS/OUTPUTS 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) 4 DCmA inputs, 4 RTD inputs 8 DCmA inputs GE Multilin F35 Multiple Feeder Protection System...
Page 38 4 DCmA inputs, 4 DCmA outputs (only one 5A module is allowed) 8 RTD inputs INPUTS/OUTPUTS 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) 4 DCmA inputs, 4 RTD inputs 8 DCmA inputs F35 Multiple Feeder Protection System GE Multilin...
Page 39: Specifications
0.1 to 2.0 × CT: ±0.5% of reading or ±0.4% of rated Inverse; IEC (and BS) A/B/C and Short (whichever is greater) Inverse; GE IAC Inverse, Short/Very/ > 2.0 × CT: ±1.5% of reading > 2.0 × CT rating Extremely Inverse; I t;...
Page 40 Level accuracy: ±0.5% of reading from 10 to 208 V sures fault duration Curve shapes: GE IAV Inverse, Definite Time Initiation: programmable per phase from any Flex- Curve multiplier: Time Dial = 0 to 600.00 in steps of 0.01...
Page 41: User-Programmable Elements
FlexLogic Number of elements: Input signals: two 8-bit integers via FlexLogic oper- ands Control signal: any FlexLogic operand Response time: < 8 ms at 60 Hz, < 10 ms at 50 Hz GE Multilin F35 Multiple Feeder Protection System 2-11...
Page 42: Monitoring
REAL POWER (WATTS) 1.2 x VT rating: ±1.0% of reading Accuracy at 0.1 to 1.5 x CT rating and 0.8 to ±1.0% of reading at –1.0 ≤ PF< –0.8 1.2 x VT rating: 2-12 F35 Multiple Feeder Protection System GE Multilin...
Page 43: Inputs
< 1 ms Debounce time: 0.0 to 16.0 ms in steps of 0.5 Continuous current draw:4 mA (when energized) Auto-burnish impulse current: 50 to 70 mA Duration of auto-burnish impulse: 25 to 50 ms GE Multilin F35 Multiple Feeder Protection System 2-13...
Page 44: Power Supply
Make and carry for 0.2 s: 30 A as per ANSI C37.90 Carry continuous: Break (DC inductive, L/R = 40 ms): VOLTAGE CURRENT 24 V 48 V 0.5 A 125 V 0.3 A 250 V 0.2 A 2-14 F35 Multiple Feeder Protection System GE Multilin...
Page 45 Note: values for 24 V and 48 V are the same due to a required 95% voltage drop across the load impedance. 0.001 Operate time: < 0.6 ms Internal Limiting Resistor: 100 Ω, 2 W GE Multilin F35 Multiple Feeder Protection System 2-15...
Page 46: Communication Protocols
–30 dBm 29 dB Singlemode 1550 nm Laser, +5 dBm –30 dBm 35 dB Singlemode These power budgets are calculated from the manu- facturer’s worst-case transmitter power and worst NOTE case receiver sensitivity. 2-16 F35 Multiple Feeder Protection System GE Multilin...
Page 47: Environmental
– Overvoltage category: 20°C Ingress protection: IP20 front, IP10 back HUMIDITY Noise: 0 dB Humidity: operating up to 95% (non-condensing) at 55°C (as per IEC60068-2-30 variant 1, 6 days). GE Multilin F35 Multiple Feeder Protection System 2-17...
Page 48: Type Tests
Safety IEC 60255-27 Insulation: class 1, Pollution degree: 2, Over voltage cat II 2.2.12 PRODUCTION TESTS THERMAL Products go through an environmental test based upon an Accepted Quality Level (AQL) sampling process. 2-18 F35 Multiple Feeder Protection System GE Multilin...
Page 49: Approvals
To avoid deterioration of electrolytic capacitors, power up units that are stored in a de-energized state once per year, for one hour continuously. GE Multilin F35 Multiple Feeder Protection System 2-19...
Page 50 2.2 SPECIFICATIONS 2 PRODUCT DESCRIPTION 2-20 F35 Multiple Feeder Protection System GE Multilin...
Page 51: Hardware
RS232 communications port. The relay is secured to the panel with the use of four screws supplied with the relay. Figure 3–1: F35 HORIZONTAL DIMENSIONS (ENHANCED PANEL) GE Multilin F35 Multiple Feeder Protection System...
Page 52 The relay must be mounted such that the faceplate sits semi-flush with the panel or switchgear door, allowing the operator access to the keypad and the RS232 communications port. The relay is secured to the panel with the use of four screws supplied with the relay. F35 Multiple Feeder Protection System GE Multilin...
Page 53 3 HARDWARE 3.1 DESCRIPTION Figure 3–4: F35 VERTICAL DIMENSIONS (ENHANCED PANEL) GE Multilin F35 Multiple Feeder Protection System...
Page 54 Figure 3–5: F35 VERTICAL MOUNTING AND DIMENSIONS (STANDARD PANEL) For side mounting F35 devices with the enhanced front panel, see the following documents available on the UR DVD and the GE Digital Energy website: • GEK-113180: UR-Series UR-V Side-Mounting Front Panel Assembly Instructions •...
Page 55 3 HARDWARE 3.1 DESCRIPTION Figure 3–6: F35 VERTICAL SIDE MOUNTING INSTALLATION (STANDARD PANEL) GE Multilin F35 Multiple Feeder Protection System...
Page 56 3.1 DESCRIPTION 3 HARDWARE Figure 3–7: F35 VERTICAL SIDE MOUNTING REAR DIMENSIONS (STANDARD PANEL) F35 Multiple Feeder Protection System GE Multilin...
Page 57: Rear Terminal Layout
(nearest to CPU module) which is indicated by an arrow marker on the terminal block. See the following figure for an example of rear terminal assignments. Figure 3–9: EXAMPLE OF MODULES IN F AND H SLOTS GE Multilin F35 Multiple Feeder Protection System...
Page 58: Wiring
3.2 WIRING 3 HARDWARE 3.2WIRING 3.2.1 TYPICAL WIRING Figure 3–10: TYPICAL WIRING DIAGRAM (T MODULE SHOWN FOR CPU) F35 Multiple Feeder Protection System GE Multilin...
Page 59: Dielectric Strength
If one of the power supplies become faulted, the second power supply assumes the full load of the relay without any interruptions. Each power supply has a green LED on the front of the module to indicate it is functional. The critical fail relay of the module also indicates a faulted power supply. GE Multilin F35 Multiple Feeder Protection System...
Page 60: Ct/Vt Modules
CT connections for both ABC and ACB phase rotations are identical as shown in the Typical wiring diagram. The exact placement of a zero-sequence core balance CT to detect ground fault current is shown as follows. Twisted-pair cabling on the zero-sequence CT is recommended. 3-10 F35 Multiple Feeder Protection System GE Multilin...
Page 61 NOTE Current inputs Voltage inputs 8F, 8G, 8L, and 8M modules (4 CTs and 4 VTs) Current inputs 8H, 8J, 8N, and 8R modules (8 CTs) 842766A3.CDR Figure 3–13: CT/VT MODULE WIRING GE Multilin F35 Multiple Feeder Protection System 3-11...
Page 62: Process Bus Modules
3.2.5 PROCESS BUS MODULES The F35 can be ordered with a process bus interface module. This module is designed to interface with the GE Multilin HardFiber system, allowing bidirectional IEC 61850 fiber optic communications with up to eight HardFiber merging units, known as Bricks.
Page 63 Logic operand driving the contact output should be given a reset delay of 10 ms to prevent damage of the output contact (in situations when the element initiating the contact output is bouncing, at val- ues in the region of the pickup value). GE Multilin F35 Multiple Feeder Protection System 3-13...
Page 64 ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs 3-14 F35 Multiple Feeder Protection System GE Multilin...
Page 65 ~5a, ~5c 2 Inputs 2 Outputs Solid-State Solid-State ~6a, ~6c 2 Inputs 2 Outputs Not Used Not Used ~7a, ~7c 2 Inputs 2 Outputs Solid-State Solid-State ~8a, ~8c 2 Inputs Not Used GE Multilin F35 Multiple Feeder Protection System 3-15...
Page 66 3.2 WIRING 3 HARDWARE Figure 3–15: CONTACT INPUT AND OUTPUT MODULE WIRING (1 of 2) 3-16 F35 Multiple Feeder Protection System GE Multilin...
Page 67 3 HARDWARE 3.2 WIRING Figure 3–16: CONTACT INPUT AND OUTPUT MODULE WIRING (2 of 2) For proper functionality, observe the polarity shown in the figures for all contact input and output con- nections. GE Multilin F35 Multiple Feeder Protection System 3-17...
Page 68 Wherever a tilde “~” symbol appears, substitute with the slot position of the module. NOTE There is no provision in the relay to detect a DC ground fault on 48 V DC control power external output. We recommend using an external DC supply. 3-18 F35 Multiple Feeder Protection System GE Multilin...
Page 69 = OFF CONTACT INPUT 1 AUTO-BURNISH = OFF CONTACT INPUT 2 AUTO-BURNISH = ON CONTACT INPUT 1 AUTO-BURNISH = ON CONTACT INPUT 2 AUTO-BURNISH = ON 842751A1.CDR Figure 3–19: AUTO-BURNISH DIP SWITCHES GE Multilin F35 Multiple Feeder Protection System 3-19...
Page 70 3.2 WIRING 3 HARDWARE The auto-burnish circuitry has an internal fuse for safety purposes. During regular maintenance, check the auto- burnish functionality using an oscilloscope. NOTE 3-20 F35 Multiple Feeder Protection System GE Multilin...
Page 71: Transducer Inputs/Outputs
(5A, 5C, 5D, 5E, and 5F) and channel arrangements that can be ordered for the relay. Wherever a tilde “~” symbol appears, substitute with the slot position of the module. NOTE Figure 3–20: TRANSDUCER INPUT/OUTPUT MODULE WIRING The following figure show how to connect RTDs. GE Multilin F35 Multiple Feeder Protection System 3-21...
Page 72 3.2 WIRING 3 HARDWARE Figure 3–21: RTD CONNECTIONS 3-22 F35 Multiple Feeder Protection System GE Multilin...
Page 73: Rs232 Faceplate Port
3.2.9 CPU COMMUNICATION PORTS a) OVERVIEW In addition to the faceplate RS232 port, the F35 provides a rear RS485 communication port. The CPU modules do not require a surge ground connection. NOTE GE Multilin F35 Multiple Feeder Protection System 3-23...
Page 74 For larger systems, additional serial channels must be added. It is also possible to use com- mercially available repeaters to have more than 32 relays on a single channel. Avoid star or stub connections entirely. 3-24 F35 Multiple Feeder Protection System GE Multilin...
Page 75 The fiber optic communication ports allow for fast and efficient communications between relays at 100 Mbps. Optical fiber can be connected to the relay supporting a wavelength of 1310 nm in multi-mode. GE Multilin F35 Multiple Feeder Protection System 3-25...
Page 76: Irig-B
GPS satellite system to obtain the time reference so that devices at different geographic locations can be syn- chronized. Figure 3–25: OPTIONS FOR THE IRIG-B CONNECTION Using an amplitude modulated receiver causes errors up to 1 ms in event time-stamping. NOTE 3-26 F35 Multiple Feeder Protection System GE Multilin...
Page 77: Direct Input/Output Communications
1 to channel 2 on UR2, the setting should be “Enabled” on UR2. This DIRECT I/O CHANNEL CROSSOVER forces UR2 to forward messages received on Rx1 out Tx2, and messages received on Rx2 out Tx1. GE Multilin F35 Multiple Feeder Protection System 3-27...
Page 78 Channel 1: RS422, channel: 820 nm, multi-mode, LED Channel 1: RS422, channel 2: 1300 nm, multi-mode, LED Channel 1: RS422, channel 2: 1300 nm, single-mode, ELED Channel 1: RS422, channel 2: 1300 nm, single-mode, laser 3-28 F35 Multiple Feeder Protection System GE Multilin...
Page 79: Fiber: Led And Eled Transmitters
The following figure shows the configuration for the 7A, 7B, 7C, 7H, 7I, and 7J fiber-only modules. Figure 3–29: LED AND ELED FIBER MODULES 3.3.3 FIBER-LASER TRANSMITTERS The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser module. Figure 3–30: LASER FIBER MODULES GE Multilin F35 Multiple Feeder Protection System 3-29...
Page 80 Observing any fiber transmitter output can injure the eye. When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the maximum optical input power to the receiver. 3-30 F35 Multiple Feeder Protection System GE Multilin...
Page 81: Interface
Remove the top cover by sliding it towards the rear and then lift it upwards. Set the timing selection switches (channel 1, channel 2) to the desired timing modes. Replace the top cover and the cover screw. GE Multilin F35 Multiple Feeder Protection System 3-31...
Page 82 For connection to a higher order system (UR- to-multiplexer, factory defaults), set to octet timing (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 = OFF). 3-32 F35 Multiple Feeder Protection System GE Multilin...
Page 83 G.703 line side of the interface while the other lies on the differential Manchester side of the interface. DMR = Differential Manchester Receiver DMX = Differential Manchester Transmitter G7X = G.703 Transmitter G7R = G.703 Receiver 842775A1.CDR Figure 3–35: G.703 DUAL LOOPBACK MODE GE Multilin F35 Multiple Feeder Protection System 3-33...
Page 84: Rs422 Interface
UR–RS422 channels is synchronized via the send timing leads on data module 1 as shown below. If the terminal timing feature is not available or this type of connection is not desired, the G.703 interface is a viable option that does not impose timing restrictions. 3-34 F35 Multiple Feeder Protection System GE Multilin...
Page 85 Figure 3–39: CLOCK AND DATA TRANSITIONS d) RECEIVE TIMING The RS422 interface utilizes NRZI-MARK modulation code and; therefore, does not rely on an Rx clock to recapture data. NRZI-MARK is an edge-type, invertible, self-clocking code. GE Multilin F35 Multiple Feeder Protection System 3-35...
Page 86: Rs422 And Fiber Interface
G.703 and fiber interfaces. When using a laser Interface, attenuators can be necessary to ensure that you do not exceed the maximum optical input power to the receiver. Figure 3–41: G.703 AND FIBER INTERFACE CONNECTION 3-36 F35 Multiple Feeder Protection System GE Multilin...
Page 87: Ieee C37.94 Interface
IEEE C37.94 standard, as shown below. In 2008, GE Digital Energy released revised modules 76 and 77 for C37.94 communication to enable multi-ended fault location functionality with firmware 5.60 release and higher. All modules 76 and 77 shipped since the change support this feature and are fully backward compatible with firmware releases below 5.60.
Page 88 Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is fully inserted. 3-38 F35 Multiple Feeder Protection System GE Multilin...
Page 89 3 HARDWARE 3.3 DIRECT INPUT/OUTPUT COMMUNICATIONS Figure 3–42: IEEE C37.94 TIMING SELECTION SWITCH SETTING GE Multilin F35 Multiple Feeder Protection System 3-39...
Page 90 Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit" • Solid red — FPGA is not receiving a valid packet or the packet received is invalid 3-40 F35 Multiple Feeder Protection System GE Multilin...
Page 91: C37.94Sm Interface
It can also can be connected directly to any other UR-series relay with a C37.94SM module as shown below. In 2008, GE Digital Energy released revised modules 2A and 2B for C37.94SM communication to enable multi-ended fault location functionality with firmware 5.60 release and higher. All modules 2A and 2B shipped since the change support this feature and are fully backward compatible with firmware releases below 5.60.
Page 92 Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is fully inserted. 3-42 F35 Multiple Feeder Protection System GE Multilin...
Page 93 Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the follow- ing figure. Figure 3–45: STATUS LEDS The clock configuration LED status is as follows: • Flashing green — loop timing mode while receiving a valid data packet GE Multilin F35 Multiple Feeder Protection System 3-43...
Page 94 Solid yellow — FPGA is receiving a "yellow bit" and remains yellow for each "yellow bit" • Solid red — FPGA is not receiving a valid packet or the packet received is invalid 3-44 F35 Multiple Feeder Protection System GE Multilin...
Page 95: Human Interfaces
Factory default values are supplied and can be restored after any changes. The following communications settings are not transferred to the F35 with settings files. Modbus Slave Address Modbus TCP Port Number RS485 COM2 Baud Rate RS485 COM2 Parity COM2 Minimum Response Time GE Multilin F35 Multiple Feeder Protection System...
Page 96 EnerVista UR Setup Help file under the topic “Upgrading Firmware”. If you are upgrading from version 7.0 or 7.1 to 7.2 or later, some CPU modules require a new boot version. Update this first in EnerVista under Maintenance > Update Firmware. F35 Multiple Feeder Protection System GE Multilin...
Page 97: Enervista Ur Setup Main Window
Settings list control bar window Device data view windows, with common tool bar Settings file data view windows, with common tool bar Workspace area with data view tabs Status bar 10. Quick action hot links GE Multilin F35 Multiple Feeder Protection System...
Page 98 4.1 ENERVISTA UR SETUP SOFTWARE INTERFACE 4 HUMAN INTERFACES 842786A2.CDR Figure 4–1: ENERVISTA UR SETUP SOFTWARE MAIN WINDOW F35 Multiple Feeder Protection System GE Multilin...
Page 99: Extended Enervista Ur Setup Features
Select the Template Mode > Edit Template option to place the device in template editing mode. Enter the template password then click OK. Open the relevant settings windows that contain settings to be specified as viewable. GE Multilin F35 Multiple Feeder Protection System...
Page 100 The following procedure describes how to add password protection to a settings file template. Select a settings file from the offline window on the left of the EnerVista UR Setup main screen. Selecting the Template Mode > Password Protect Template option. F35 Multiple Feeder Protection System GE Multilin...
Page 101 Template Mode > View In Template Mode command. The template specifies that only the Pickup Curve Phase time overcurrent settings window without template applied. settings be available. 842858A1.CDR Figure 4–4: APPLYING TEMPLATES VIA THE VIEW IN TEMPLATE MODE COMMAND GE Multilin F35 Multiple Feeder Protection System...
Page 102 Select an installed device or settings file from the tree menu on the left of the EnerVista UR Setup main screen. Select the Template Mode > Remove Settings Template option. Enter the template password and click OK to continue. F35 Multiple Feeder Protection System GE Multilin...
Page 103: Securing And Locking Flexlogic Equations
Click on Save to save and apply changes to the settings template. Select the Template Mode > View In Template Mode option to view the template. Apply a password to the template then click OK to secure the FlexLogic equation. GE Multilin F35 Multiple Feeder Protection System...
Page 104 FlexLogic entries in a settings file have been secured, use the following procedure to lock the settings file to a specific serial number. Select the settings file in the offline window. Right-click on the file and select the Edit Settings File Properties item. 4-10 F35 Multiple Feeder Protection System GE Multilin...
Page 105: Settings File Traceability
F35 device. Any partial settings transfers by way of drag and drop do not add the traceability information to the settings file. Figure 4–11: SETTINGS FILE TRACEABILITY MECHANISM With respect to the above diagram, the traceability feature is used as follows. GE Multilin F35 Multiple Feeder Protection System 4-11...
Page 106 Figure 4–12: DEVICE DEFINITION SHOWING TRACEABILITY DATA This information is also available in printed settings file reports as shown in the example below. Traceability data in settings report 842862A1.CDR Figure 4–13: SETTINGS FILE REPORT SHOWING TRACEABILITY DATA 4-12 F35 Multiple Feeder Protection System GE Multilin...
Page 107 If the user converts an existing settings file to another revision, then any existing traceability information is removed from the settings file. • If the user duplicates an existing settings file, then any traceability information is transferred to the duplicate settings file. GE Multilin F35 Multiple Feeder Protection System 4-13...
Page 108: Faceplate Interface
The following figure shows the horizontal arrange- ment of the faceplate panels. Figure 4–16: UR-SERIES STANDARD HORIZONTAL FACEPLATE PANELS 4-14 F35 Multiple Feeder Protection System GE Multilin...
Page 109: Led Indicators
The status indicators in the first column are described below. • IN SERVICE: This LED indicates that control power is applied, all monitored inputs, outputs, and internal systems are OK, and that the device has been programmed. GE Multilin F35 Multiple Feeder Protection System 4-15...
Page 110 LED indicator or target message, once the condition has been cleared (these latched conditions can also be reset via the   menu). The RS232 port is for connection to a com- SETTINGS INPUT/OUTPUTS RESETTING puter. keys are used by the breaker control feature. USER 4-16 F35 Multiple Feeder Protection System GE Multilin...
Page 111 User customization of LED operation is of maximum benefit in installations where languages other than English are used to communicate with operators. Refer to the User-programmable LEDs section in chapter 5 for the settings used to program the operation of the LEDs on these panels. GE Multilin F35 Multiple Feeder Protection System 4-17...
Page 112: Custom Labeling Of Leds
EnerVista UR Setup software is installed and operational • The F35 settings have been saved to a settings file • The F35 front panel label cutout sheet (GE Multilin part number 1006-0047) has been downloaded from http://www.gedigitalenergy.com/products/support/ur/URLEDenhanced.doc and printed •...
Page 113 Remove the F35 label insert tool from the package and bend the tabs as described in the following procedures. These tabs are used for removal of the default and custom LED labels. It is important that the tool be used EXACTLY as shown below, with the printed side containing the GE part number facing the user.
Page 114 Use the knife to lift the LED label and slide the label tool underneath. Make sure the bent tabs are pointing away from the relay. Slide the label tool under the LED label until the tabs snap out as shown below. This attaches the label tool to the LED label. 4-20 F35 Multiple Feeder Protection System GE Multilin...
Page 115 Use the knife to lift the pushbutton label and slide the tail of the label tool underneath, as shown below. Make sure the bent tab is pointing away from the relay. GE Multilin F35 Multiple Feeder Protection System 4-21...
Page 116 Slide the label tool under the user-programmable pushbutton label until the tabs snap out as shown below. This attaches the label tool to the user-programmable pushbutton label. Remove the tool and attached user-programmable pushbutton label as shown below. 4-22 F35 Multiple Feeder Protection System GE Multilin...
Page 117: Display
1. For the following discussion it is assumed the     SETTINGS SYSTEM SETUP BREAKERS BREAKER 1(2) BREAKER setting is "Enabled" for each breaker. FUNCTION GE Multilin F35 Multiple Feeder Protection System 4-23...
Page 118: Menus
Press the MENU key to select a header display page (top-level menu). The header title appears momentarily followed by a header display page menu item. Each press of the MENU key advances through the following main heading pages: • Actual values • Settings 4-24 F35 Multiple Feeder Protection System GE Multilin...
Page 119 4 HUMAN INTERFACES 4.3 FACEPLATE INTERFACE • Commands • Targets • User displays (when enabled) GE Multilin F35 Multiple Feeder Protection System 4-25...
Page 120 Pressing the MESSAGE DOWN key displays the second setting sub-header associ-  PROPERTIES ated with the Product Setup header.  Press the MESSAGE RIGHT key once more to display the first setting for Display FLASH MESSAGE Properties. TIME: 1.0 s 4-26 F35 Multiple Feeder Protection System GE Multilin...
Page 121: Changing Settings
ENTERING ALPHANUMERIC TEXT Text settings have data values which are fixed in length, but user-defined in character. They can be upper case letters, lower case letters, numerals, and a selection of special characters. GE Multilin F35 Multiple Feeder Protection System 4-27...
Page 122: Settings
When the "NEW SETTING HAS BEEN STORED" message appears, the relay is in "Programmed" state and the In Service LED turns on. e) ENTERING INITIAL PASSWORDS The F35 supports password entry from a local or remote connection. 4-28 F35 Multiple Feeder Protection System GE Multilin...
Page 123 FlexLogic™ operand is set to “On” and the F35 does not allow settings or LOCAL ACCESS DENIED command level access via the faceplate interface for the next five minutes. GE Multilin F35 Multiple Feeder Protection System 4-29...
Page 124 FlexLogic™ operand is set to “Off” after five minutes for a Command password or 30 minutes for a Settings pass- DENIED word. These default settings can be changed in EnerVista under Settings > Product Setup > Security. 4-30 F35 Multiple Feeder Protection System GE Multilin...
Page 125: Overview
See page 5-74.   TELEPROTECTION See page 5-81.   INSTALLATION See page 5-82.   SETTINGS  AC INPUTS See page 5-84.  SYSTEM SETUP   POWER SYSTEM See page 5-85.  GE Multilin F35 Multiple Feeder Protection System...
Page 126  SELECTOR SWITCH See page 5-153.   UNDERFREQUENCY See page 5-159.   AUTORECLOSE See page 5-160.   DIGITAL ELEMENTS See page 5-166.   DIGITAL COUNTERS See page 5-169.  F35 Multiple Feeder Protection System GE Multilin...
Page 127  IEC 61850 See page 5-205.  GOOSE UINTEGERS  SETTINGS  DCMA INPUTS See page 5-206.  TRANSDUCER I/O   RTD INPUTS See page 5-207.   DCMA OUTPUTS See page 5-209.  GE Multilin F35 Multiple Feeder Protection System...
Page 128: Introduction To Elements
For wye-connected VTs, the primary and secondary bases quanitities are as before, but the secondary voltage (here a phase-to-phase ground value) is: 13800 --------------- - --------- - × 66.4 V (EQ 5.2) 14400 Many settings are common to most elements and are discussed below: F35 Multiple Feeder Protection System GE Multilin...
Page 129: Introduction To Ac Sources
The same considerations apply to transformer winding 2. The protection elements require access to the net current for transformer protection, but some elements may need access to the individual currents from CT1 and CT2. GE Multilin F35 Multiple Feeder Protection System...
Page 130 CT/VT MODULE 1 CT/VT MODULE 2 CT/VT MODULE 3 < bank 1 > < bank 3 > < bank 5 > < bank 2 > < bank 4 > < bank 6 > F35 Multiple Feeder Protection System GE Multilin...
Page 131 Upon startup, the CPU configures the settings required to characterize the current and voltage inputs, and will display them in the appropriate section in the sequence of the banks (as described above) as follows for a maximum configuration: F1, F5, M1, M5, U1, and U5. GE Multilin F35 Multiple Feeder Protection System...
Page 132: Product Setup
If the connection is to the back of the F35, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password must be used. settings allows recording of password access events in the event recorder. PASSWORD ACCESS EVENTS F35 Multiple Feeder Protection System GE Multilin...
Page 133 NOTE If a remote connection is established, local passcodes are not visible. NOTE c) REMOTE PASSWORDS The remote password settings are visible only from a remote connection via the EnerVista UR Setup software. GE Multilin F35 Multiple Feeder Protection System...
Page 134 ALARMS operand does not generate events or targets. If events or targets are required, the operand can be assigned to a digital element programmed UNAUTHORIZED ACCESS with event logs or targets enabled. 5-10 F35 Multiple Feeder Protection System GE Multilin...
Page 135 ACCESS AUTH TIMEOUT immediately denied. If access is permitted and an off-to-on transition of the FlexLogic operand is detected, the timeout is restarted. The status of this timer is updated every 5 seconds. GE Multilin F35 Multiple Feeder Protection System 5-11...
Page 136: Cybersentry Security
Ethernet-to-RS485 gateway is not supported. Because these gateways do not support the secure protocols necessary to communicate with such devices, the connection cannot be established. Use the device as a non-CyberSentry device. 5-12 F35 Multiple Feeder Protection System GE Multilin...
Page 137 UR device for successful authentication, and the shortname is a short, optional alias that can be used in place of the IP address. client 10.0.0.2/24 { secret = testing123 shortname = private-network-1 e. In the \etc\raddb folder, create a file called dictionary.ge and add the following content. # ########################################################## # GE VSA's ############################################################ VENDOR...
Page 138 Set up the RADIUS parameters on the UR as follows. Access Device > Settings > Product Setup > Security. Con- figure the IP address and ports for the RADIUS server. Leave the GE vendor ID field at the default of 2910. Update the RADIUS shared secret as specified in the clients.conf file.
Page 139 The “login setting” in this menu is similar to the login setting described in PATH: SETTINGS > PRODUCT SETUP > SECU- RITY except for the factory role. Passwords are stored in text format. No encryption is applied. Notes: NOTE GE Multilin F35 Multiple Feeder Protection System 5-15...
Page 140 Range: Enabled, Disabled FACTORY SERVICE: MESSAGE MODE: Disabled  SELF TESTS MESSAGE See below  Range: Enabled, Disabled SUPERVISOR ROLE: MESSAGE Disabled Range: 1 to 9999 minutes SERIAL INACTIVITY MESSAGE TIMEOUT: 1 min 5-16 F35 Multiple Feeder Protection System GE Multilin...
Page 141 Example: If this setting is "Yes" and an attempt is made to change settings or upgrade the firmware, the UR device denies the setting changes and denies upgrading the firmware. If this setting is "No", the UR device accepts setting changes and firmware upgrade. This role is disabled by default. GE Multilin F35 Multiple Feeder Protection System 5-17...
Page 142 Username — 255 chars maximum, but in the security log it is truncated to 20 characters IP address — Device IP address Role — 16 bit unsigned, of type format F617 ENUMERATION ROLE None Administrator Supervisor Engineer Operator Factory 5-18 F35 Multiple Feeder Protection System GE Multilin...
Page 143: Display Properties
DEFAULT MESSAGE TIMEOUT: If the keypad is inactive for a period of time, the relay automatically reverts to a default message. The inactivity time is modified via this setting to ensure messages remain on the screen long enough during programming or reading of actual values. GE Multilin F35 Multiple Feeder Protection System 5-19...
Page 144 Any calculated power value below this cut-off will not be displayed. As well, the three-phase energy data will not accumu- late if the total power from all three phases does not exceed the power cut-off. 5-20 F35 Multiple Feeder Protection System GE Multilin...
Page 145: Clear Relay Records
Set the properties for user-programmable pushbutton 1 by making the following changes in the  SETTINGS PRODUCT   menu: SETUP USER-PROGRAMMABLE PUSHBUTTONS USER PUSHBUTTON 1 “Self-reset” PUSHBUTTON 1 FUNCTION: “0.20 s” PUSHBTN 1 DROP-OUT TIME: GE Multilin F35 Multiple Feeder Protection System 5-21...
Page 146: Communications
End nodes can communicate with each other using all supported protocols of the UR family on a local network. In a routed network, it is recommended to upgrade the UR device used to 7.1x or higher where routing capability through static route settings has been introduced. 5-22 F35 Multiple Feeder Protection System GE Multilin...
Page 147 EnerVista, and access to the public network shared on the same LAN. No redundancy is provided. Figure 5–3: NETWORK CONFIGURATION FOR SINGLE LAN Public Network SCADA EnerVista Software LAN1 ML3000 IP1/ MAC1 859708A2.vsd GE Multilin F35 Multiple Feeder Protection System 5-23...
Page 148 LAN3, to which port 3 (P3) is connected. There is no redundancy. Figure 5–5: MULTIPLE LANS, NO REDUNDANCY Public Network SCADA EnerVista Software LAN1 LAN2 LAN3 ML3000 ML3000 ML3000 IP1/ IP2/ IP3/ MAC2 MAC3 MAC1 859710A2.vsd 5-24 F35 Multiple Feeder Protection System GE Multilin...
Page 149 IP address. The client software (EnerVista UR Setup, for example) must be configured to use the correct port number if these settings are used. GE Multilin F35 Multiple Feeder Protection System...
Page 150 MODBUS TCP PORT NUMBER F35 is restarted. NOTE Do not set more than one protocol to the same TCP/UDP port number, as this results in unreliable operation of those protocols. 5-26 F35 Multiple Feeder Protection System GE Multilin...
Page 151 DEADBAND: 30000 Range: 0 to 100000000 in steps of 1 DNP OTHER DEFAULT MESSAGE DEADBAND: 30000 Range: 1 to 10080 min. in steps of 1 DNP TIME SYNC IIN MESSAGE PERIOD: 1440 min GE Multilin F35 Multiple Feeder Protection System 5-27...
Page 152 Do not set more than one protocol to the same TCP/UDP port number, as this results in unreliable operation of those protocols. setting is the DNP slave address. This number identifies the F35 on a DNP communications link. Each DNP ADDRESS DNP slave should be assigned a unique address. 5-28 F35 Multiple Feeder Protection System GE Multilin...
Page 153 1, 2, 20, 21, 22, 23, 30, and 32. The default variation refers to the variation response when variation 0 is requested and/or in class 0, 1, 2, or 3 scans. Refer to the DNP implementation section in appendix E for additional details. GE Multilin F35 Multiple Feeder Protection System 5-29...
Page 154 Up to 256 analog input points can be configured for the DNP or IEC 60870-5-104 protocols. The analog point list is config- ured by assigning an appropriate FlexAnalog parameter to each point. Refer to Appendix A: FlexAnalog Parameters for the full range of assignable parameters. 5-30 F35 Multiple Feeder Protection System GE Multilin...
Page 155 The F35 supports the Manufacturing Message Specification (MMS) protocol as specified by IEC 61850. MMS is supported over two protocol stacks: TCP/IP over Ethernet. The F35 operates as an IEC 61850 server. The Remote inputs and outputs section in this chapter describe the peer-to-peer GSSE/GOOSE message scheme. GE Multilin F35 Multiple Feeder Protection System 5-31...
Page 156 IEC 61850 GSSE application ID name string sent as part of each GSSE message. This GSSE ID string identifies the GSSE message to the receiving device. In F35 releases previous to 5.0x, this name string was repre- sented by the setting. RELAY NAME 5-32 F35 Multiple Feeder Protection System GE Multilin...
Page 157 ID for each GOOSE sending device. This value can be left at its default if the feature is not required. Both the GOOSE VLAN settings are required by IEC 61850. PRIORITY GOOSE ETYPE APPID GE Multilin F35 Multiple Feeder Protection System 5-33...
Page 158 The aggressive scheme is only supported in fast type 1A GOOSE messages (GOOSEOut 1 and GOOSEOut 2). For slow GOOSE messages (GOOSEOut 3 to GOOSEOut 8) the aggressive scheme is the same as the medium scheme. 5-34 F35 Multiple Feeder Protection System GE Multilin...
Page 159 Configure the transmission dataset. Configure the GOOSE service settings. Configure the data. The general steps required for reception configuration are: Configure the reception dataset. Configure the GOOSE service settings. Configure the data. GE Multilin F35 Multiple Feeder Protection System 5-35...
Page 160 Configure the GOOSE service settings by making the following changes in the  INPUTS/OUTPUTS REMOTE DEVICES  settings menu: REMOTE DEVICE 1 – to match the GOOSE ID string for the transmitting device. Enter “GOOSEOut_1”. REMOTE DEVICE 1 ID 5-36 F35 Multiple Feeder Protection System GE Multilin...
Page 161 The status value for GGIO1.ST.Ind1.stVal is determined by the FlexLogic operand assigned to GGIO1 indication 1. Changes to this operand will result in the transmission of GOOSE messages con- taining the defined dataset. GE Multilin F35 Multiple Feeder Protection System 5-37...
Page 162 Received values are used to populate the GGIO3.MX.AnIn1 and higher items. Received values are also available as FlexAnalog parameters (GOOSE analog In1 and up). GGIO3.MX.AnIn1 to GGIO3.MX.AnIn32 can only be used once for all sixteen reception datasets. NOTE 5-38 F35 Multiple Feeder Protection System GE Multilin...
Page 163 F35. Clients will still be able to connect to the server (F35 relay), but most data values will not be updated. This setting does not affect GOOSE/GSSE operation. Changes to the setting, setting, and GOOSE dataset will not take effect until the F35 is restarted. IED NAME LD INST NOTE GE Multilin F35 Multiple Feeder Protection System 5-39...
Page 164 275 × VT ratio setting • power (real, reactive, and apparent): 46 × phase CT primary setting × 275 × VT ratio setting • • frequency: 90 Hz • power factor: 2 5-40 F35 Multiple Feeder Protection System GE Multilin...
Page 165 GGIO4. When this value is NUMBER OF ANALOG POINTS changed, the F35 must be rebooted in order to allow the GGIO4 logical node to be re-instantiated and contain the newly configured number of analog points. GE Multilin F35 Multiple Feeder Protection System 5-41...
Page 166 GGIO5 integer inputs. The following setting is available for all GGIO5 configuration points. • GGIO5 UINT IN 1 VALUE: This setting selects the FlexInteger value to drive each GGIO5 integer status value (GGIO5.ST.UIntIn1). This setting is stored as an 32-bit unsigned integer value. 5-42 F35 Multiple Feeder Protection System GE Multilin...
Page 167 XCBR operating counter status attribute (OpCnt) increments with every operation. Frequent breaker operation may result in very large OpCnt values over time. This setting allows the OpCnt to be reset to “0” for XCBR1. GE Multilin F35 Multiple Feeder Protection System...
Page 168 When the port is set to 0, the change takes effect when the F35 is restarted. Do not set more than one protocol to the same TCP/UDP port number, as this results in unreliable operation of NOTE those protocols. 5-44 F35 Multiple Feeder Protection System GE Multilin...
Page 169 (usually either an RTU or a SCADA master station). Since the F35 maintains two sets of IEC 60870-5-104 data change buffers, no more than two masters should actively communicate with the F35 at one time. GE Multilin F35 Multiple Feeder Protection System...
Page 170 The relay supports one fast Ethernet Global Data (EGD) exchange and two slow EGD exchanges. There are 20 data items in the fast-produced EGD exchange and 50 data items in each slow-produced exchange. 5-46 F35 Multiple Feeder Protection System GE Multilin...
Page 171 (Modbus register address range in decimal) Slow EGD exchanges (500 to 1000 ms) are generally used for the transfer and display of data items. The settings for the fast and slow exchanges are described below: GE Multilin F35 Multiple Feeder Protection System 5-47...
Page 172: Modbus User Map
REAL TIME CLOCK MESSAGE EVENTS: Disabled Range: None, DC Shift, Amplitude Modulated IRIG-B SIGNAL TYPE: MESSAGE None  PRECISION TIME MESSAGE See below  PROTOCOL (1588)  SNTP PROTOCOL MESSAGE See below  5-48 F35 Multiple Feeder Protection System GE Multilin...
Page 173 2) connection to a network device that does not support the PTP peer delay mechanism, 3) jitter substantially greater than 1 µs in received event messages, and 4) certain non-compliant announce and sync message update rates. GE Multilin F35 Multiple Feeder Protection System...
Page 174 It is provided in compliance with PP. As these messages have a destination address that indicates they are not to be bridged, their VLAN ID serves no function, and so may be left at its default value. 5-50 F35 Multiple Feeder Protection System GE Multilin...
Page 175 (>1024 seconds) without receiving an SNTP broadcast message before signaling an SNTP self-test error. is 123 for normal SNTP operation. If SNTP is not required, close the port by setting it to 0. SNTP UDP PORT NUMBER GE Multilin F35 Multiple Feeder Protection System 5-51...
Page 176 DAYLIGHT SAVINGS TIME (DST) Note that when IRIG-B time synchronization is active, the local time in the IRIG-B signal contains any daylight savings time offset and so the DST settings are ignored. 5-52 F35 Multiple Feeder Protection System GE Multilin...
Page 177: Fault Reports
Elements operated at the time of triggering. • Events: 9 before trigger and 7 after trigger (only available via the relay webpage). • Fault duration times for each breaker (created by the breaker arcing current feature). GE Multilin F35 Multiple Feeder Protection System 5-53...
Page 178 It should be kept in mind that grounding points in vicinity of the installation impact the system zero-sequence impedance (grounded loads, reactors, zig-zag transformers, shunt capacitor banks, etc.). 5-54 F35 Multiple Feeder Protection System GE Multilin...
Page 179: Oscillography
64 samples per cycle; that is, it has no effect on the fundamental calculations of the device. When changes are made to the oscillography settings, all existing oscillography records will be CLEARED. NOTE GE Multilin F35 Multiple Feeder Protection System 5-55...
Page 180 IB signal on terminal 2 of the CT/VT module in slot F. If there are no CT/VT modules and analog input modules, no analog traces will appear in the file; only the digital traces will appear. 5-56 F35 Multiple Feeder Protection System GE Multilin...
Page 181: Data Logger
436380 s 254460 s 3600000 ms 2727.5 235645200 s 340.9 29455200 s 26182800 s Changing any setting affecting data logger operation will clear any data that is currently in the log. NOTE GE Multilin F35 Multiple Feeder Protection System 5-57...
Page 182: Demand
D 1 e (EQ 5.6) – where: d = demand value after applying input quantity for time t (in minutes) D = input quantity (constant), and k = 2.3 / thermal 90% response time. 5-58 F35 Multiple Feeder Protection System GE Multilin...
Page 183: User-Programmable Leds
 TRIP & ALARM LEDS MESSAGE See page 5–62.   USER-PROGRAMMABLE MESSAGE See page 5–62.  LED 1  USER-PROGRAMMABLE MESSAGE  LED 2 ↓  USER-PROGRAMMABLE MESSAGE  LED 48 GE Multilin F35 Multiple Feeder Protection System 5-59...
Page 184 The test responds to the position and rising edges of the control input defined by the set- LED TEST CONTROL ting. The control pulses must last at least 250 ms to take effect. The following diagram explains how the test is executed. 5-60 F35 Multiple Feeder Protection System GE Multilin...
Page 185 2. Once stage 2 has started, the pushbutton can be released. When stage 2 is completed, stage 3 will automatically start. The test may be aborted at any time by pressing the pushbutton. GE Multilin F35 Multiple Feeder Protection System...
Page 186 AR ENABLED LED 10 operand BREAKER 1 CLOSED LED 22 operand AR DISABLED LED 11 operand BREAKER 1 TROUBLE LED 23 operand AR RIP LED 12 operand LED 24 operand AR LO 5-62 F35 Multiple Feeder Protection System GE Multilin...
Page 187: User-Programmable Self Tests
ANY SELF-TEST mode, minor alarms continue to function along with other major and minor alarms. Refer to the Relay self-tests section in chapter 7 for additional information on major and minor self-test alarms. GE Multilin F35 Multiple Feeder Protection System 5-63...
Page 188: Control Pushbuttons
An event is logged in the event record (as per user setting) when a control pushbutton is pressed. No event is logged when the pushbutton is released. The faceplate keys (including control keys) cannot be operated simultaneously – a given key must be released before the next one can be pressed. 5-64 F35 Multiple Feeder Protection System GE Multilin...
Page 189: User-Programmable Pushbuttons
PUSHBTN 1 DROP-OUT MESSAGE TIME: 0.00 s Range: FlexLogic operand PUSHBTN 1 LED CTL: MESSAGE Range: Disabled, Normal, High Priority PUSHBTN 1 MESSAGE: MESSAGE Disabled Range: Disabled, Enabled PUSHBUTTON 1 MESSAGE EVENTS: Disabled GE Multilin F35 Multiple Feeder Protection System 5-65...
Page 190 The pushbutton is reset (deactivated) in latched mode by asserting the operand assigned to the set- PUSHBTN 1 RESET ting or by directly pressing the associated active front panel pushbutton. 5-66 F35 Multiple Feeder Protection System GE Multilin...
Page 191 This timer is reset upon release of the pushbutton. Note that any pushbutton operation will require the pushbutton to be pressed a minimum of 50 ms. This minimum time is required prior to activating the pushbutton hold timer. GE Multilin F35 Multiple Feeder Protection System...
Page 192 “Normal” if the setting is “High Priority” or “Normal”. PUSHBTN 1 MESSAGE • PUSHBUTTON 1 EVENTS: If this setting is enabled, each pushbutton state change will be logged as an event into event recorder. 5-68 F35 Multiple Feeder Protection System GE Multilin...
Page 193 Off = 0 SETTING SETTING Autoreset Delay Autoreset Function = Enabled = Disabled SETTING Drop-Out Timer TIMER FLEXLOGIC OPERAND 200 ms PUSHBUTTON 1 ON 842021A3.CDR Figure 5–13: USER-PROGRAMMABLE PUSHBUTTON LOGIC (Sheet 1 of 2) GE Multilin F35 Multiple Feeder Protection System 5-69...
Page 194 User-programmable pushbuttons require a type HP or HQ faceplate. If an HP or HQ type faceplate was ordered separately, the relay order code must be changed to indicate the correct faceplate option. This can be done via EnerVista UR Setup with the Maintenance > Enable Pushbutton command. NOTE 5-70 F35 Multiple Feeder Protection System GE Multilin...
Page 195: Flex State Parameters
• USER-PROGRAMMABLE CONTROL INPUT: The user-definable displays also respond to the INVOKE AND SCROLL setting. Any FlexLogic operand (in particular, the user-programmable pushbutton operands), can be used to navigate the programmed displays. GE Multilin F35 Multiple Feeder Protection System 5-71...
Page 196 (setting, actual value, or command) which has a Modbus address, to view the hexadecimal form of the Modbus address, then manually convert it to decimal form before entering it (EnerVista UR Setup usage conveniently facilitates this conversion). 5-72 F35 Multiple Feeder Protection System GE Multilin...
Page 197 If the parameters for the top line and the bottom line items have the same units, then the unit is displayed on the bottom line only. The units are only displayed on both lines if the units specified both the top and bottom line items are different. NOTE GE Multilin F35 Multiple Feeder Protection System 5-73...
Page 198: Direct Inputs/Outputs
“Yes”), all direct output messages should be received back. If not, the direct input/output ring CH2 RING CONFIGURATION break self-test is triggered. The self-test error is signaled by the FlexLogic operand. DIRECT RING BREAK 5-74 F35 Multiple Feeder Protection System GE Multilin...
Page 199 The following application examples illustrate the basic concepts for direct input and output configuration. Please refer to the Inputs and outputs section in this chapter for information on configuring FlexLogic operands (flags, bits) to be exchanged. GE Multilin F35 Multiple Feeder Protection System...
Page 200 UR IED 1 BLOCK UR IED 4 UR IED 2 UR IED 3 842712A1.CDR Figure 5–16: SAMPLE INTERLOCKING BUSBAR PROTECTION SCHEME For increased reliability, a dual-ring configuration (shown below) is recommended for this application. 5-76 F35 Multiple Feeder Protection System GE Multilin...
Page 201 The complete application requires addressing a number of issues such as failure of both the communications rings, failure or out-of-service conditions of one of the relays, etc. Self-monitoring flags of the direct inputs and outputs feature would be primarily used to address these concerns. GE Multilin F35 Multiple Feeder Protection System 5-77...
Page 202 Inputs and outputs section. A blocking pilot-aided scheme should be implemented with more security and, ideally, faster message delivery time. This could be accomplished using a dual-ring configuration as shown below. 5-78 F35 Multiple Feeder Protection System GE Multilin...
Page 203 FlexLogic operand is set. When the total message counter reaches the user-defined maximum specified by the set- CRC ALARM CH1 MESSAGE COUNT ting, both the counters reset and the monitoring process is restarted. GE Multilin F35 Multiple Feeder Protection System 5-79...
Page 204 The unreturned messages alarm function is available on a per-channel basis and is active only in the ring configuration. The total number of unreturned input and output messages is available as the   ACTUAL VALUES STATUS DIRECT  actual value. INPUTS UNRETURNED MSG COUNT CH1 5-80 F35 Multiple Feeder Protection System GE Multilin...
Page 205: Teleprotection
On two- terminals two-channel systems, the same is transmitted over LOCAL RELAY ID NUMBER both channels; as such, only the has to be programmed on the receiving end. TERMINAL 1 ID NUMBER GE Multilin F35 Multiple Feeder Protection System 5-81...
Page 206: Installation
"Programmed" state. UNIT NOT PROGRAMMED setting allows the user to uniquely identify a relay. This name will appear on generated reports. RELAY NAME 5-82 F35 Multiple Feeder Protection System GE Multilin...
Page 207: Remote Resources Configuration
Configure shared inputs and outputs as required for the application's functionality. Shared inputs and outputs are dis- tinct binary channels that provide high-speed protection quality signaling between relays through a Brick. For additional information on how to configure a relay with a process bus module, see GE publication number GEK-113658: HardFiber Process Bus System Instruction Manual.
Page 208: System Setup
1000:1 CT before summation. If a protection element is set up to act on SRC 1 currents, then a pickup level of 1 pu will operate on 1000 A primary. The same rule applies for current sums from CTs with different secondary taps (5 A and 1 A). 5-84 F35 Multiple Feeder Protection System GE Multilin...
Page 209: Power System
Range: ABC, ACB PHASE ROTATION: MESSAGE Range: SRC 1, SRC 2, SRC 3, SRC 4, SRC 5, SRC 6 FREQUENCY AND PHASE MESSAGE REFERENCE: SRC 1 Range: Disabled, Enabled FREQUENCY TRACKING: MESSAGE Enabled GE Multilin F35 Multiple Feeder Protection System 5-85...
Page 210: Signal Sources
For example, the selection “F1+F5” indicates the sum of each phase from channels “F1” and “F5”, scaled to whichever CT has the higher ratio. Selecting “None” hides the associated actual values. 5-86 F35 Multiple Feeder Protection System GE Multilin...
Page 211 0.02 pu; thus by default the disturbance detector responds to a change of 0.04 pu. The metering sensitivity setting ( PROD-   ) controls the sensitivity of the disturbance detector UCT SETUP DISPLAY PROPERTIES CURRENT CUT-OFF LEVEL accordingly. GE Multilin F35 Multiple Feeder Protection System 5-87...
Page 212 Figure 5–23: EXAMPLE USE OF SOURCES Y LV D HV SRC 1 SRC 2 SRC 3 Phase CT F1+F5 None Ground CT None None Phase VT None None Aux VT None None 5-88 F35 Multiple Feeder Protection System GE Multilin...
Page 213: Breakers
Range: 0.000 to 65.535 s in steps of 0.001 MANUAL CLOSE RECAL1 MESSAGE TIME: 0.000 s Range: FlexLogic operand BREAKER 1 OUT OF SV: MESSAGE Range: Disabled, Enabled BREAKER 1 EVENTS: MESSAGE Disabled GE Multilin F35 Multiple Feeder Protection System 5-89...
Page 214 MANUAL CLOSE RECAL1 TIME: This setting specifies the interval required to maintain setting changes in effect after an operator has initiated a manual close command to operate a circuit breaker. • BREAKER 1 OUT OF SV: Selects an operand indicating that breaker 1 is out-of-service. 5-90 F35 Multiple Feeder Protection System GE Multilin...
Page 215 5.4 SYSTEM SETUP Figure 5–24: DUAL BREAKER CONTROL SCHEME LOGIC (Sheet 1 of 2) IEC 61850 functionality is permitted when the F35 is in “Programmed” mode and not in the local control mode. NOTE GE Multilin F35 Multiple Feeder Protection System 5-91...
Page 216 5.4 SYSTEM SETUP 5 SETTINGS Figure 5–25: DUAL BREAKER CONTROL SCHEME LOGIC (Sheet 2 of 2) 5-92 F35 Multiple Feeder Protection System GE Multilin...
Page 217: Disconnect Switches
• SWITCH 1 MODE: This setting selects “3-Pole” mode, where disconnect switch poles have a single common auxiliary switch, or “1-Pole” mode where each disconnect switch pole has its own auxiliary switch. GE Multilin F35 Multiple Feeder Protection System 5-93...
Page 218 This allows for non-simultaneous operation of the poles. IEC 61850 functionality is permitted when the F35 is in “Programmed” mode and not in the local control mode. NOTE 5-94 F35 Multiple Feeder Protection System GE Multilin...
Page 219 5 SETTINGS 5.4 SYSTEM SETUP Figure 5–26: DISCONNECT SWITCH SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-95...
Page 220: Flexcurves
1.03 pu. It is recommended to set the two times to a similar value; otherwise, the linear approximation may result in NOTE undesired behavior for the operating quantity that is close to 1.00 pu. 5-96 F35 Multiple Feeder Protection System GE Multilin...
Page 221 The multiplier and adder settings only affect the curve portion of the characteristic and not the MRT and HCT set- tings. The HCT settings override the MRT settings for multiples of pickup greater than the HCT ratio. NOTE GE Multilin F35 Multiple Feeder Protection System 5-97...
Page 222 EnerVista UR Setup software generates an error message and discards the proposed changes. NOTE e) STANDARD RECLOSER CURVES The standard recloser curves available for the F35 are displayed in the following graphs. 5-98 F35 Multiple Feeder Protection System GE Multilin...
Page 223 842723A1.CDR Figure 5–30: RECLOSER CURVES GE101 TO GE106 GE142 GE138 GE120 GE113 0.05 7 8 9 10 12 CURRENT (multiple of pickup) 842725A1.CDR Figure 5–31: RECLOSER CURVES GE113, GE120, GE138 AND GE142 GE Multilin F35 Multiple Feeder Protection System 5-99...
Page 224 Figure 5–32: RECLOSER CURVES GE134, GE137, GE140, GE151 AND GE201 GE152 GE141 GE131 GE200 7 8 9 10 12 CURRENT (multiple of pickup) 842728A1.CDR Figure 5–33: RECLOSER CURVES GE131, GE141, GE152, AND GE200 5-100 F35 Multiple Feeder Protection System GE Multilin...
Page 225 Figure 5–34: RECLOSER CURVES GE133, GE161, GE162, GE163, GE164 AND GE165 GE132 GE139 GE136 GE116 0.05 GE117 GE118 0.02 0.01 7 8 9 10 12 CURRENT (multiple of pickup) 842726A1.CDR Figure 5–35: RECLOSER CURVES GE116, GE117, GE118, GE132, GE136, AND GE139 GE Multilin F35 Multiple Feeder Protection System 5-101...
Page 226 Figure 5–36: RECLOSER CURVES GE107, GE111, GE112, GE114, GE115, GE121, AND GE122 GE202 GE135 GE119 7 8 9 10 12 CURRENT (multiple of pickup) 842727A1.CDR Figure 5–37: RECLOSER CURVES GE119, GE135, AND GE202 5-102 F35 Multiple Feeder Protection System GE Multilin...
Page 227: Flexlogic
Traditionally, protective relay logic has been relatively limited. Any unusual applications involving interlocks, blocking, or supervisory functions had to be hard-wired using contact inputs and outputs. FlexLogic minimizes the requirement for aux- iliary components and wiring while making more complex schemes possible. GE Multilin F35 Multiple Feeder Protection System 5-103...
Page 228 The virtual input is presently in the ON state. Virtual Output Virt Op 1 On The virtual output is presently in the set state (i.e. evaluation of the equation which produces this virtual output results in a "1"). 5-104 F35 Multiple Feeder Protection System GE Multilin...
Page 229 BRK RESTRIKE 1 OP C Breaker restrike detected in phase C of the breaker control 1 element BKR RESTRIKE 2 to 3 Same set of operands as shown for BKR RESTRIKE 1 GE Multilin F35 Multiple Feeder Protection System 5-105...
Page 230 INCIPNT FLT 1 PKP C Asserted when incipient cable fault detector 1 picks up in phase C INCIPNT FLT 2 to 6 Same set of operands as shown for INCIPNT FLT 1 5-106 F35 Multiple Feeder Protection System GE Multilin...
Page 231 Phase B of phase time overcurrent 1 has dropped out PHASE TOC1 DPO C Phase C of phase time overcurrent 1 has dropped out PHASE TOC2 to 6 Same set of operands as shown for PHASE TOC1 GE Multilin F35 Multiple Feeder Protection System 5-107...
Page 232 TELEPRO CH2 CRC FAIL CRC detected packet corruption on channel 2 TELEPRO CH1 PKT LOST CRC detected lost packet on channel 1 TELEPRO CH2 PKT LOST CRC detected lost packet on channel 2 5-108 F35 Multiple Feeder Protection System GE Multilin...
Page 233 Virt Ip 1 Flag is set, logic=1 Virtual inputs Virt Ip 2 Flag is set, logic=1 Virt Ip 3 Flag is set, logic=1 ↓ ↓ Virt Ip 64 Flag is set, logic=1 GE Multilin F35 Multiple Feeder Protection System 5-109...
Page 234 See description in Chapter 7: Commands and targets TEMP MONITOR Monitors ambient temperature and maximum operating temperature UNIT NOT PROGRAMMED The Settings > Product Setup > Installation > Relay Settings setting is not programmed 5-110 F35 Multiple Feeder Protection System GE Multilin...
Page 235 2 to 16 any input is ‘1’ 2 to 16 all inputs are ‘1’ 2 to 16 all inputs are ‘0’ NAND 2 to 16 any input is ‘0’ only one input is ‘1’ GE Multilin F35 Multiple Feeder Protection System 5-111...
Page 236: Flexlogic Rules
When making changes to FlexLogic entries in the settings, all FlexLogic equations are re-compiled whenever any new FlexLogic entry value is entered, and as a result of the re-compile all latches are reset automatically. 5-112 F35 Multiple Feeder Protection System GE Multilin...
Page 237: Flexlogic Example
Dropout State=Pickup (200 ms) DIGITAL ELEMENT 2 Timer 1 State=Operated Time Delay on Pickup (800 ms) CONTACT INPUT H1c State=Closed VIRTUAL OUTPUT 3 827026A2.VSD Figure 5–40: LOGIC EXAMPLE WITH VIRTUAL OUTPUTS GE Multilin F35 Multiple Feeder Protection System 5-113...
Page 238 Following the procedure outlined, start with parameter 99, as follows: 99: The final output of the equation is virtual output 3, which is created by the operator "= Virt Op n". This parameter is therefore "= Virt Op 3." 5-114 F35 Multiple Feeder Protection System GE Multilin...
Page 239 87: The input just below the upper input to OR #1 is operand “Virt Op 2 On". 86: The upper input to OR #1 is operand “Virt Op 1 On". 85: The last parameter is used to set the latch, and is operand “Virt Op 4 On". GE Multilin F35 Multiple Feeder Protection System 5-115...
Page 240 In the following equation, virtual output 3 is used as an input to both latch 1 and timer 1 as arranged in the order shown below: DIG ELEM 2 OP Cont Ip H1c On AND(2) 5-116 F35 Multiple Feeder Protection System GE Multilin...
Page 241: Flexlogic Equation Editor
TIMER 1 TYPE: This setting is used to select the time measuring unit. • TIMER 1 PICKUP DELAY: Sets the time delay to pickup. If a pickup delay is not required, set this function to "0". GE Multilin F35 Multiple Feeder Protection System 5-117...
Page 242: Flexelements
The element can be programmed to respond either to a signal level or to a rate-of-change (delta) over a pre-defined period of time. The output operand is asserted when the operating signal is higher than a threshold or lower than a threshold as per user's choice. 5-118 F35 Multiple Feeder Protection System GE Multilin...
Page 243 The FLEXELEMENT 1 DIRECTION following figure explains the application of the FLEXELEMENT 1 DIRECTION FLEXELEMENT 1 PICKUP FLEXELEMENT 1 HYS- settings. TERESIS GE Multilin F35 Multiple Feeder Protection System 5-119...
Page 244 Figure 5–47: FLEXELEMENT DIRECTION, PICKUP, AND HYSTERESIS In conjunction with the setting the element could be programmed to provide two extra charac- FLEXELEMENT 1 INPUT MODE teristics as shown in the figure below. 5-120 F35 Multiple Feeder Protection System GE Multilin...
Page 245 = 360 degrees (see the UR angle referencing convention) BASE POWER FACTOR = 1.00 BASE RTDs BASE = 100°C SOURCE CURRENT = maximum nominal primary RMS value of the +IN and –IN inputs BASE GE Multilin F35 Multiple Feeder Protection System 5-121...
Page 246 “Delta”. FLEXELEMENT 1 COMP MODE This setting specifies the pickup delay of the element. The setting FLEXELEMENT 1 PKP DELAY FLEXELEMENT 1 RST DELAY specifies the reset delay of the element. 5-122 F35 Multiple Feeder Protection System GE Multilin...
Page 247: Non-Volatile Latches
LATCH N LATCH N LATCH N TYPE RESET Reset Dominant Previous Previous State State Dominant Previous Previous State State Figure 5–49: NON-VOLATILE LATCH OPERATION TABLE (N = 1 to 16) AND LOGIC GE Multilin F35 Multiple Feeder Protection System 5-123...
Page 248: Grouped Elements
5.6.3 PHASE CURRENT a) INVERSE TIME OVERCURRENT CURVE CHARACTERISTICS The inverse time overcurrent curves used by the time overcurrent elements are the IEEE, IEC, GE Type IAC, and I t stan- dard curve shapes. This allows for simplified coordination with downstream devices.
Page 249 4.827 38.634 22.819 14.593 11.675 10.130 9.153 8.470 7.960 7.562 7.241 51.512 30.426 19.458 15.567 13.507 12.204 11.294 10.614 10.083 9.654 10.0 64.390 38.032 24.322 19.458 16.883 15.255 14.117 13.267 12.604 12.068 GE Multilin F35 Multiple Feeder Protection System 5-125...
Page 250 1.835 1.067 0.668 0.526 0.451 0.404 0.371 0.346 0.327 0.311 0.80 2.446 1.423 0.890 0.702 0.602 0.538 0.494 0.461 0.435 0.415 1.00 3.058 1.778 1.113 0.877 0.752 0.673 0.618 0.576 0.544 0.518 5-126 F35 Multiple Feeder Protection System GE Multilin...
Page 251 = characteristic constant, and T = reset time in seconds (assuming energy capacity is 100% RESET is “Timed”) RESET Table 5–17: GE TYPE IAC INVERSE TIME CURVE CONSTANTS IAC CURVE SHAPE IAC Extreme Inverse 0.0040 0.6379 0.6200 1.7872 0.2461...
Page 252 = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed) RESET RECLOSER CURVES: The F35 uses the FlexCurve feature to facilitate programming of 41 recloser curves. Please refer to the FlexCurve section in this chapter for additional details. 5-128 F35 Multiple Feeder Protection System GE Multilin...
Page 253 ‘Mvr’ times the setting. If the voltage restraint feature PHASE TOC1 PICKUP is disabled, the pickup level always remains at the setting value. GE Multilin F35 Multiple Feeder Protection System 5-129...
Page 254 PHASE TOC1 C DPO Multiplier-Phase C PHASE TOC1 C OP SETTING PHASE TOC1 PKP PHASE TOC1 VOLT RESTRAINT: PHASE TOC1 OP Enabled PHASE TOC1 DPO 827072A4.CDR Figure 5–51: PHASE TIME OVERCURRENT 1 SCHEME LOGIC 5-130 F35 Multiple Feeder Protection System GE Multilin...
Page 255 The input current is the fundamental phasor magnitude. For timing curves, see the publication Instan- taneous Overcurrent Element Response to Saturated Waveforms in UR-Series Relays (GET-8400A). Figure 5–52: PHASE INSTANTANEOUS OVERCURRENT 1 SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-131...
Page 256: Neutral Current
RESET: NEUTRAL TOC1 PKP NEUTRAL TOC1 IN ≥ PICKUP NEUTRAL TOC1 DPO SOURCE: NEUTRAL TOC1 OP SETTING NEUTRAL TOC1 BLOCK: Off = 0 827034A3.VSD Figure 5–53: NEUTRAL TIME OVERCURRENT 1 SCHEME LOGIC 5-132 F35 Multiple Feeder Protection System GE Multilin...
Page 257 RESET DELAY : SETTING NEUTRAL IOC1 DPO NEUTRAL IOC1 OP 3( _0 - K _1 ) PICKUP NEUTRAL IOC1 BLOCK: Off=0 SETTING NEUTRAL IOC1 SOURCE: 827035A4.CDR Figure 5–54: NEUTRAL IOC1 SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-133...
Page 258: Wattmetric Ground Fault
VT connected to the auxiliary channel bank of the relay). When the latter selection is made, the auxiliary channel must be identified by the user as a neutral voltage under the VT bank settings. This element will operate only if the aux- iliary voltage is configured as neutral. 5-134 F35 Multiple Feeder Protection System GE Multilin...
Page 259   FlexCurve --------- - (EQ 5.19)   Again, the FlexCurve timer starts after the definite time timer expires. GE Multilin F35 Multiple Feeder Protection System 5-135...
Page 260 Figure 5–55: WATTMETRIC CHARACTERISTIC ANGLE RESPONSE • WATTMETRIC GND FLT 1 MULTIPLIER: This setting is applicable if above is selected WATTMETRIC GND FLT 1 CURVE to Inverse and defines the multiplier factor for the inverse time delay. 5-136 F35 Multiple Feeder Protection System GE Multilin...
Page 261 5 SETTINGS 5.6 GROUPED ELEMENTS Figure 5–56: WATTMETRIC ZERO-SEQUENCE DIRECTIONAL LOGIC GE Multilin F35 Multiple Feeder Protection System 5-137...
Page 262: Ground Current
GROUND TOC 1 SETTING GROUND TOC1 PKP RESET: GROUND TOC1 IG ≥ PICKUP GROUND TOC1 DPO SOURCE: GROUND TOC1 OP SETTING GROUND TOC1 BLOCK: Off = 0 827036A3.VSD Figure 5–57: GROUND TOC1 SCHEME LOGIC 5-138 F35 Multiple Feeder Protection System GE Multilin...
Page 263 Enabled = 1 SETTING DELAY: GROUND IOC1 GROUND IOC1 RESET SETTING PICKUP: DELAY: GROUND IOC1 SOURCE: IG ≥ PICKUP SETTING GROUND IOC1 BLOCK: 827037A4.VSD Off = 0 Figure 5–58: GROUND IOC1 SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-139...
Page 264: Negative Sequence Current
MESSAGE See page 5–142.   NEG SEQ IOC2 MESSAGE See page 5–142.  For additional information on the negative sequence time overcurrent curves, see the Inverse Time Overcurrent Curves section earlier. 5-140 F35 Multiple Feeder Protection System GE Multilin...
Page 265 < NEG SEQ PICKUP NEG SEQ TOC1 DPO NEG SEQ TOC1 BLOCK: NEG SEQ TOC1 OP Off=0 SETTING NEG SEQ TOC1 SOURCE: Neg Seq 827057A4.CDR Figure 5–59: NEGATIVE SEQUENCE TOC1 SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-141...
Page 266 SETTING NEG SEQ IOC1 DPO NEG SEQ IOC1 OP _2 - K _1 PICKUP NEG SEQ IOC1 BLOCK: Off=0 SETTING NEG SEQ IOC1 SOURCE: 827058A5.CDR Figure 5–60: NEGATIVE SEQUENCE IOC1 SCHEME LOGIC 5-142 F35 Multiple Feeder Protection System GE Multilin...
Page 267: Voltage Elements
The time delay is adjustable from 0 to 600.00 seconds in steps of 0.01. The undervoltage elements can also be programmed to have an inverse time delay char- acteristic. GE Multilin F35 Multiple Feeder Protection System 5-143...
Page 268 V = secondary voltage applied to the relay = pickup level pickup % of voltage pickup 842788A1.CDR Figure 5–61: INVERSE TIME UNDERVOLTAGE CURVES At 0% of pickup, the operating time equals the UNDERVOLTAGE DELAY setting. NOTE 5-144 F35 Multiple Feeder Protection System GE Multilin...
Page 269 FLEXLOGIC OPERAND SETTING PHASE UV1 PKP PHASE UV1 MODE: FLEXLOGIC OPERAND Phase to Ground Phase to Phase PHASE UV1 OP FLEXLOGIC OPERAND PHASE UV1 DPO 827039AB.CDR Figure 5–62: PHASE UNDERVOLTAGE1 SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-145...
Page 270 “Definite time”. The source assigned to this element must be configured for a phase VT. NEUTRAL OV1 CURVE VT errors and normal voltage unbalance must be considered when setting this element. This function requires the VTs to be wye-connected. Figure 5–63: NEUTRAL OVERVOLTAGE1 SCHEME LOGIC 5-146 F35 Multiple Feeder Protection System GE Multilin...
Page 271 AUX UV1 PKP AUX UV1 DPO SETTING SETTING AUX UV1 OP AUX UV1 MINIMUM AUX UV1 SIGNAL VOLTAGE: SOURCE: < AUX VOLT Vx Vx Minimum 827849A2.CDR Figure 5–64: AUXILIARY UNDERVOLTAGE SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-147...
Page 272 Off=0 DELAY : FLEXLOGIC OPERANDS < Vx Pickup AUX OV1 OP SETTING AUX OV1 DPO AUX OV1 SIGNAL AUX OV1 PKP SOURCE: AUXILIARY VOLT (Vx) 827836A2.CDR Figure 5–65: AUXILIARY OVERVOLTAGE SCHEME LOGIC 5-148 F35 Multiple Feeder Protection System GE Multilin...
Page 273: Control Elements
If more than one operate-type operand is required, it may be assigned directly from the trip bus menu. GE Multilin F35 Multiple Feeder Protection System...
Page 274 TRIP BUS 1 RESET: The trip bus output is reset when the operand assigned to this setting is asserted. Note that the operand is pre-wired to the reset gate of the latch, As such, a reset command the front panel interface or via RESET OP communications will reset the trip bus output. 5-150 F35 Multiple Feeder Protection System GE Multilin...
Page 275: Setting Groups
The setting groups menu controls the activation and deactivation of up to six possible groups of settings in the GROUPED settings menu. The faceplate Settings In Use LEDs indicate which active group (with a non-flashing energized ELEMENTS LED) is in service. GE Multilin F35 Multiple Feeder Protection System 5-151...
Page 276 OR (2) AND (3) = VIRT OP 1 (VO1) PHASE TOC1 PKP PHASE TOC2 PKP AND (3) = VIRT OP 1 (VO1) 842789A1.CDR Figure 5–68: EXAMPLE FLEXLOGIC CONTROL OF A SETTINGS GROUP 5-152 F35 Multiple Feeder Protection System GE Multilin...
Page 277: Selector Switch
1 to the . If the control word is outside the range, an alarm is established SELECTOR FULL RANGE by setting the FlexLogic operand for 3 seconds. SELECTOR ALARM GE Multilin F35 Multiple Feeder Protection System 5-153...
Page 278 SELECTOR 1 3BIT ACK: This setting specifies an acknowledging input for the three-bit control input. The pre- selected position is applied on the rising edge of the assigned FlexLogic operand. This setting is active only under the 5-154 F35 Multiple Feeder Protection System GE Multilin...
Page 279 The selector position pre-selected via the stepping up control input has not been confirmed before the time out. SELECTOR 1 BIT ALARM The selector position pre-selected via the three-bit control input has not been confirmed before the time out. GE Multilin F35 Multiple Feeder Protection System 5-155...
Page 280 3BIT A2 POS 1 POS 2 POS 3 POS 4 POS 5 POS 6 POS 7 BIT 0 BIT 1 BIT 2 STP ALARM BIT ALARM ALARM 842737A1.CDR Figure 5–69: TIME-OUT MODE 5-156 F35 Multiple Feeder Protection System GE Multilin...
Page 281 Make the following changes to selector switch element in the    SETTINGS CONTROL ELEMENTS SELECTOR SWITCH menu to assign control to user programmable pushbutton 1 and contact inputs 1 through 3: SELECTOR SWITCH 1 GE Multilin F35 Multiple Feeder Protection System 5-157...
Page 282 SELECTOR 1 BIT ALARM 3-bit position out SELECTOR 1 ALARM SELECTOR 1 PWR ALARM SELECTOR 1 BIT 0 SELECTOR 1 BIT 1 SELECTOR 1 BIT 2 842012A2.CDR Figure 5–71: SELECTOR SWITCH LOGIC 5-158 F35 Multiple Feeder Protection System GE Multilin...
Page 283: Underfrequency
≤ 0 < f PICKUP UNDERFREQ 1 OP UNDERFREQ 1 ACTUAL VALUES MIN VOLT / AMP: UNDERFREQ 1 SOURCE: ≥ Level Minimum VOLT / AMP Frequency 827079A8.CDR Figure 5–72: UNDERFREQUENCY SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-159...
Page 284: Autoreclose
4.000 s Range: FlexLogic operand AR1 ADD DELAY 1: MESSAGE Range: 0.00 to 655.35 s in steps of 0.01 AR1 DELAY 1: MESSAGE 0.000 s Range: FlexLogic operand AR1 ADD DELAY 2: MESSAGE 5-160 F35 Multiple Feeder Protection System GE Multilin...
Page 285 Scheme lockout blocks all phases of the reclosing cycle, preventing automatic reclosure, if any of the following occurs: • The maximum shot number was reached. • A ‘Block’ input is in effect (for instance; Breaker Failure, bus differential protection operated, etc.). GE Multilin F35 Multiple Feeder Protection System 5-161...
Page 286 ‘reclose-in-progress’ state. If all condi- tions allowing a breaker closure are not satisfied when this time expires, the scheme goes to “Lockout”. This timer must be set to a delay less than the reset timer. NOTE 5-162 F35 Multiple Feeder Protection System GE Multilin...
Page 287 5 SETTINGS 5.7 CONTROL ELEMENTS To sheet 2 Figure 5–73: AUTORECLOSURE SCHEME LOGIC (Sheet 1 of 2) GE Multilin F35 Multiple Feeder Protection System 5-163...
Page 288 5.7 CONTROL ELEMENTS 5 SETTINGS Figure 5–74: AUTORECLOSURE SCHEME LOGIC (Sheet 2 of 2) 5-164 F35 Multiple Feeder Protection System GE Multilin...
Page 289 5 SETTINGS 5.7 CONTROL ELEMENTS Figure 5–75: SINGLE SHOT AUTORECLOSING SEQUENCE - PERMANENT FAULT GE Multilin F35 Multiple Feeder Protection System 5-165...
Page 290: Digital Elements
DIGITAL ELEMENT 1 RESET DELAY: Sets the time delay to reset. If a reset delay is not required, set to “0”. • DIGITAL ELEMENT 1 PICKUP LED: This setting enables or disabled the digital element pickup LED. When set to “Disabled”, the operation of the pickup LED is blocked. 5-166 F35 Multiple Feeder Protection System GE Multilin...
Page 291 In most breaker control circuits, the trip coil is connected in series with a breaker auxiliary contact which is open when the breaker is open (see diagram below). To prevent unwanted alarms in this situation, the trip circuit monitoring logic must include the breaker position. Figure 5–77: TRIP CIRCUIT EXAMPLE 1 GE Multilin F35 Multiple Feeder Protection System 5-167...
Page 292 In this case, it is not required to supervise the monitoring circuit with the breaker position – the setting is BLOCK selected to “Off”. In this case, the settings are as follows (EnerVista UR Setup example shown). Figure 5–78: TRIP CIRCUIT EXAMPLE 2 5-168 F35 Multiple Feeder Protection System GE Multilin...
Page 293: Digital Counters
–2,147,483,648 counts, the counter will rollover to +2,147,483,647. • COUNTER 1 BLOCK: Selects the FlexLogic operand for blocking the counting operation. All counter operands are blocked. GE Multilin F35 Multiple Feeder Protection System 5-169...
Page 294 COUNTER 1 FROZEN: Off = 0 STORE DATE & TIME Date & Time SETTING COUNT1 FREEZE/RESET: Off = 0 827065A1.VSD SETTING COUNT1 FREEZE/COUNT: Off = 0 Figure 5–79: DIGITAL COUNTER SCHEME LOGIC 5-170 F35 Multiple Feeder Protection System GE Multilin...
Page 295: 8-Bit Switches
If the control operand is in the "Off" state, the first (A) input is switched to the output. If the control operand is in the "On" state, the second (B) input is switched to the output. The switching takes place instantaneously. GE Multilin F35 Multiple Feeder Protection System...
Page 296 FLEXLOGIC OPERAND Off = 0 8BIT SW 1 ARG B7: 8BIT SWITCH 1 BIT 7 Off = 0 SETTING 8BIT SW 1 CONTROL: Off = 0 842017A1.CDR Figure 5–80: 8-BIT SWITCH LOGIC 5-172 F35 Multiple Feeder Protection System GE Multilin...
Page 297: Monitoring Elements
See page 5–180.   BROKEN CONDUCTOR 3 MESSAGE See page 5–180.  ↓  BROKEN CONDUCTOR 6 MESSAGE See page 5–180.   THERMAL OVERLOAD MESSAGE See page 5–183.  PROTECTION GE Multilin F35 Multiple Feeder Protection System 5-173...
Page 298 • BKR 1 ARC AMP LIMIT: Selects the threshold value above which the output operand is set. 5-174 F35 Multiple Feeder Protection System GE Multilin...
Page 299 BKR 1 ARCING AMP C Φ 827071A3.CDR BKR 1 OPERATING TIME A Φ BKR 1 OPERATING TIME B Φ BKR 1 OPERATING TIME C Φ BKR 1 OPERATING TIME Figure 5–82: BREAKER ARCING CURRENT SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-175...
Page 300 A restrike event (FlexLogic operand) is declared if all of the following hold: • The current is initially interrupted. 5-176 F35 Multiple Feeder Protection System GE Multilin...
Page 301 “1” when breaker is opened, either manually or from protection logic. • BRK RSTR 1 CLS CMD: This setting assigns a FlexLogic operand indicating a breaker close command. It must be logic “1” when breaker is closed. GE Multilin F35 Multiple Feeder Protection System 5-177...
Page 302 Due to shortness of such spikes, they are not usually detected by the instantaneous protection of the feeder, which operates on the RMS or fundamental component of the phase current with a relatively high pickup. 5-178 F35 Multiple Feeder Protection System GE Multilin...
Page 303 INCIPIENT FLT 1 TRIP COUNTS NUMBER: This setting selects the number of faults required to initiate a trip. • INCIPNT FLT 1 DETECT WINDOW: This setting specifies a time window for “Counts per window” mode of operation. GE Multilin F35 Multiple Feeder Protection System 5-179...
Page 304 It also monitors changes in the I_2 / I_1 ratio, I_1 minimum, and I_1 maximum. 5-180 F35 Multiple Feeder Protection System GE Multilin...
Page 305 • BROKEN CONDUCTOR 1 PKP DELAY: This setting specifies the pickup time delay for this function to operate after assertion of the broken conductor pickup FlexLogic operand. GE Multilin F35 Multiple Feeder Protection System 5-181...
Page 306 5.7 CONTROL ELEMENTS 5 SETTINGS Figure 5–88: BROKEN CONDUCTOR DETECTION LOGIC 5-182 F35 Multiple Feeder Protection System GE Multilin...
Page 307 • = measured load RMS current before overload occurs. • k= IEC 255-8 k-factor applied to I , defining maximum permissible current above nominal current. • = protected element base (nominal) current. GE Multilin F35 Multiple Feeder Protection System 5-183...
Page 308 When current is greater than the pickup level, I > k × I , element starts increasing the thermal energy: t Δ -------------- - (EQ 5.25) – op In 5-184 F35 Multiple Feeder Protection System GE Multilin...
Page 309 30 minutes Busbar 60 minutes 20 minutes Underground cable 20 to 60 minutes 60 minutes The logic for the thermal overload protection element is shown below. Figure 5–90: THERMAL OVERLOAD PROTECTION SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-185...
Page 310: Pid Regulator
Range: 1 to 20 s in steps of 1 PID 1 DEAD TIME: MESSAGE 1.00 sec Range: FlexLogic operand PID 1 BLK: MESSAGE Range: Self-reset, Latched, Disabled PID 1 MESSAGE TARGET: Self-reset Range: Enabled, Disabled PID 1 MESSAGE EVENTS: Disabled 5-186 F35 Multiple Feeder Protection System GE Multilin...
Page 311 AW is a flag which enables anti-windup. The incremental form of the above equation is: Du k ( ) u k ( ) u k 1 – – (EQ 5.28) Dp k ( ) Di k ( ) Dd k ( ) Where: GE Multilin F35 Multiple Feeder Protection System 5-187...
Page 312 Dd k 1 ----------------------- - y k ( ) 2y k 1 y k 2 ----------------------- - – – – – The PID regulator logic is shown below. Figure 5–92: PID REGULATOR LOGIC 5-188 F35 Multiple Feeder Protection System GE Multilin...
Page 313: Inputs And Outputs
The update is performed at the beginning of the protection pass so all protection and control functions, as well as FlexLogic equations, are fed with the updated states of the contact inputs. GE Multilin F35 Multiple Feeder Protection System...
Page 314 Event Records menu, make the following settings changes: "Breaker Closed (52b)" CONTACT INPUT H5A ID: "Enabled" CONTACT INPUT H5A EVENTS: Note that the 52b contact is closed when the breaker is open and open when the breaker is closed. 5-190 F35 Multiple Feeder Protection System GE Multilin...
Page 315: Virtual Inputs
“Virtual Input 1 to OFF = 0” VIRTUAL INPUT 1 ID: (Flexlogic Operand) SETTING Virt Ip 1 VIRTUAL INPUT 1 TYPE: Latched Self - Reset 827080A2.CDR Figure 5–94: VIRTUAL INPUTS SCHEME LOGIC GE Multilin F35 Multiple Feeder Protection System 5-191...
Page 316: Contact Outputs
L-Cont Op 1 Range: FlexLogic operand OUTPUT H1a OPERATE: MESSAGE Range: FlexLogic operand OUTPUT H1a RESET: MESSAGE Range: Operate-dominant, Reset-dominant OUTPUT H1a TYPE: MESSAGE Operate-dominant Range: Disabled, Enabled OUTPUT H1a EVENTS: MESSAGE Disabled 5-192 F35 Multiple Feeder Protection System GE Multilin...
Page 317 Application Example 3: A make before break functionality must be added to the preceding example. An overlap of 20 ms is required to implement this functionality as described below: GE Multilin F35 Multiple Feeder Protection System 5-193...
Page 318: Virtual Outputs
Logic equations. Any change of state of a virtual output can be logged as an event if programmed to do so. For example, if Virtual Output 1 is the trip signal from FlexLogic and the trip relay is used to signal events, the settings would be programmed as follows: 5-194 F35 Multiple Feeder Protection System GE Multilin...
Page 319: Remote Devices
PRODUCT SETUP COMMUNICATIONS IEC 61850 PROTOCOL GSSE/GOOSE    setting. CONFIGURATION TRANSMISSION GSSE GSSE ID In F35 releases previous to 5.0x, these name strings were represented by the setting. RELAY NAME GE Multilin F35 Multiple Feeder Protection System 5-195...
Page 320: Remote Inputs
(see the Remote devices section). The setting selects the specific bits of the REMOTE DEVICE (16) ID REMOTE IN 1 ITEM GSSE/GOOSE message required. 5-196 F35 Multiple Feeder Protection System GE Multilin...
Page 321: Remote Double-Point Status Inputs
REMOTE OUTPUTS DNA BIT PAIRS REMOTE OUTPUTS DNA- 1(32) BIT PAIR Range: FlexLogic operand  REMOTE OUTPUTS DNA- 1 OPERAND:  DNA- 1 BIT PAIR Range: Disabled, Enabled DNA- 1 EVENTS: MESSAGE Disabled GE Multilin F35 Multiple Feeder Protection System 5-197...
Page 322: Resetting
RESET OP to identify the source of the command. The setting RESET OP (PUSHBUTTON) RESET OP (COMMS) RESET OP (OPERAND) shown above selects the operand that will create the operand. RESET OP (OPERAND) 5-198 F35 Multiple Feeder Protection System GE Multilin...
Page 323: Direct Inputs And Outputs
APPLICATION EXAMPLES The examples introduced in the earlier Direct inputs and outputs section (part of the Product Setup section) are continued below to illustrate usage of the direct inputs and outputs. GE Multilin F35 Multiple Feeder Protection System 5-199...
Page 324 DIRECT INPUT 7 DEFAULT STATE : "3" DIRECT INPUT 8 DEVICE ID : "3" DIRECT INPUT 8 BIT NUMBER : select "On" for security, select "Off" for dependability DIRECT INPUT 8 DEFAULT STATE 5-200 F35 Multiple Feeder Protection System GE Multilin...
Page 325 "3" (effectively, this is a message from IED 1) DIRECT INPUT 6 BIT NUMBER: UR IED 2: "1" DIRECT INPUT 5 DEVICE ID: "2" DIRECT INPUT 5 BIT NUMBER: "3" DIRECT INPUT 6 DEVICE ID: GE Multilin F35 Multiple Feeder Protection System 5-201...
Page 326: Teleprotection Inputs And Outputs
Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-1 MESSAGE DEFAULT: Off Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-2 MESSAGE DEFAULT: Off ↓ Range: Off, On, Latest/Off, Latest/On TELEPROT INPUT 2-16 MESSAGE DEFAULT: Off 5-202 F35 Multiple Feeder Protection System GE Multilin...
Page 327 (teleprotection outputs at the sending end or corresponding teleprotection inputs at the receiving end). On three-terminal two-channel systems, redundancy is achieved by programming signal re-transmittal in the case of channel failure between any pair of relays. GE Multilin F35 Multiple Feeder Protection System 5-203...
Page 328: Iec 61850 Goose Analogs
GOOSE analog input value. GOOSE Analogs are floating-point values, with no units. The GOOSE UNIT and PU base settings allow the user to configure GOOSE Analog, so that it can be used in a FlexElement. 5-204 F35 Multiple Feeder Protection System GE Multilin...
Page 329: Iec 61850 Goose Integers
“Default Value”, then the value of the GOOSE uinteger input is defined by the setting. UINTEGER 1 DEFAULT The GOOSE integer input FlexInteger values are available for use in other F35 functions that use FlexInteger values. GE Multilin F35 Multiple Feeder Protection System 5-205...
Page 330: Transducer Inputs And Outputs
–20 to +180 MW; in this case the value would be “–20” and the DCMA INPUT H1 MIN VALUE DCMA INPUT H1 MAX value “180”. Intermediate values between the min and max values are scaled linearly. VALUE 5-206 F35 Multiple Feeder Protection System GE Multilin...
Page 331: Rtd Inputs
1.5 pu. FlexElement operands are available to FlexLogic for further interlocking or to operate an output contact directly. Refer to the following table for reference temperature values for each RTD type. GE Multilin F35 Multiple Feeder Protection System 5-207...
Page 332 168.47 280.77 233.97 16.00 172.46 291.96 243.30 16.39 175.84 303.46 252.88 16.78 179.51 315.31 262.76 17.17 183.17 327.54 272.94 17.56 186.82 340.14 283.45 17.95 190.45 353.14 294.28 18.34 194.08 366.53 305.44 18.73 5-208 F35 Multiple Feeder Protection System GE Multilin...
Page 333: Dcma Outputs
The feature is intentionally inhibited if the settings are entered incorrectly, e.g. when – MAX VAL MIN VAL MAX VAL < 0.1 pu. The resulting characteristic is illustrated in the following figure. GE Multilin F35 Multiple Feeder Protection System 5-209...
Page 334 The minimum and maximum power values to be monitored (in pu) are: 20.65 MW 20.65 MW – ------------------------------ -------------------------- - minimum power 1.247 pu, maximum power 1.247 pu (EQ 5.35) – 16.56 MW 16.56 MW The following settings should be entered: 5-210 F35 Multiple Feeder Protection System GE Multilin...
Page 335 The minimum and maximum voltage values to be monitored (in pu) are: 161.66 kV 254.03 kV -------------------------- - -------------------------- - minimum voltage 0.404 pu, maximum voltage 0.635 pu (EQ 5.41) 400 kV 400 kV The following settings should be entered: GE Multilin F35 Multiple Feeder Protection System 5-211...
Page 336 1.27 kV – • ±0.5% of reading For example, under nominal conditions, the positive-sequence reads 230.94 kV and the worst-case error is 0.005 x 230.94 kV + 1.27 kV = 2.42 kV. 5-212 F35 Multiple Feeder Protection System GE Multilin...
Page 337: Testing
The test mode state is indicated on the relay faceplate by a combination of the Test Mode LED indicator, the In-Service LED indicator, and by the critical fail relay, as shown in the following table. GE Multilin F35 Multiple Feeder Protection System...
Page 338: Force Contact Inputs
Mode LED will be on, indicating that the relay is in test mode. The state of each contact input may be programmed as “Dis- abled”, “Open”, or “Closed”. All contact input operations return to normal when all settings for this feature are disabled. 5-214 F35 Multiple Feeder Protection System GE Multilin...
Page 339: Force Contact Outputs
PUSHBUTTON 1 FUNCTION input 1 to initiate the Test mode, make the following changes in the menu:   SETTINGS TESTING TEST MODE “Enabled” and “ ” TEST MODE FUNCTION: TEST MODE INITIATE: GE Multilin F35 Multiple Feeder Protection System 5-215...
Page 340 5.10 TESTING 5 SETTINGS 5-216 F35 Multiple Feeder Protection System GE Multilin...
Page 341: Actual Values
 STATUS  IEC 61850 See page 6-10.  GOOSE UINTEGERS  EGD PROTOCOL See page 6-10.  STATUS  TELEPROT CH TESTS See page 6-11.   INCIPIENT FAULT See page 6-11.  GE Multilin F35 Multiple Feeder Protection System...
Page 342  FAULT REPORTS See page 6-25.  RECORDS   EVENT RECORDS See page 6-25.   OSCILLOGRAPHY See page 6-26.   DATA LOGGER See page 6-26.   MAINTENANCE See page 6-27.  F35 Multiple Feeder Protection System GE Multilin...
Page 343 6 ACTUAL VALUES 6.1 OVERVIEW  ACTUAL VALUES  MODEL INFORMATION See page 6-28.  PRODUCT INFO   FIRMWARE REVISIONS See page 6-28.  GE Multilin F35 Multiple Feeder Protection System...
Page 344: Contact Inputs
The state displayed will be that of the remote point unless the remote device has been established to be “Offline” in which case the value shown is the programmed default state for the remote input. F35 Multiple Feeder Protection System GE Multilin...
Page 345: Remote Double-Point Status Inputs
The present state of the contact outputs is shown here. The first line of a message display indicates the ID of the contact output. For example, ‘Cont Op 1’ refers to the contact output in terms of the default name-array index. The second line of the display indicates the logic state of the contact output. GE Multilin F35 Multiple Feeder Protection System...
Page 346: Virtual Outputs
The present state of the programmed remote devices is shown here. The message indicates ALL REMOTE DEVICES ONLINE whether or not all programmed remote devices are online. If the corresponding state is "No", then at least one required remote device is not online. F35 Multiple Feeder Protection System GE Multilin...
Page 347: Digital Counters
Range: Current Position / 7 SELECTOR SWITCH 2 MESSAGE POSITION: 0/7 The display shows both the current position and the full range. The current position only (an integer from 0 through 7) is the actual value. GE Multilin F35 Multiple Feeder Protection System...
Page 348: Flex States
PTP grandmaster, this actual value is zero. The grandmasterIdentity code is specified by PTP to be globally unique, so one can always know which clock is grandmaster in a system with multiple grandmaster-capable clocks. F35 Multiple Feeder Protection System GE Multilin...
Page 349: Direct Inputs
The UNRETURNED MSG COUNT CRC FAIL values can be cleared using the command. COUNT CLEAR DIRECT I/O COUNTERS values represent the state of each direct input. DIRECT INPUT 1 DIRECT INPUT (32) GE Multilin F35 Multiple Feeder Protection System...
Page 350: Direct Devices Status
FAST EXCHANGE 1 MESSAGE DATA LENGTH: These values provide information that may be useful for debugging an EGD network. The EGD signature and packet size for the fast EGD exchange is displayed. 6-10 F35 Multiple Feeder Protection System GE Multilin...
Page 351: Teleprotection Channel Tests
The number of detected incipient faults for each incipient fault element are displayed here for each phase. These values can be reset to zero with the   command. COMMANDS CLEAR RECORDS CLEAR INCIPENT FAULT COUNTERS GE Multilin F35 Multiple Feeder Protection System 6-11...
Page 352: Remaining Connection Status
UR over Ethernet, the Modbus TCP status shows 3. If the EnerVista application is closed, the Modbus TCP status shows 4. Note that the maximum number of PMU TCP connections matches the number of aggregators. 6-12 F35 Multiple Feeder Protection System GE Multilin...
Page 353: Metering Conventions
WATTS = Negative VARS = Positive PF = Lead PF = Lag PF = Lead Current UR RELAY 827239AC.CDR S=VI Generator Figure 6–1: FLOW DIRECTION OF SIGNED VALUES FOR WATTS AND VARS GE Multilin F35 Multiple Feeder Protection System 6-13...
Page 354 ABC phase rotation: • ACB phase rotation: -- - V -- - V -- - V -- - V -- - V -- - V The above equations apply to currents as well. 6-14 F35 Multiple Feeder Protection System GE Multilin...
Page 355 SYSTEM SETUP POWER SYSTEM FREQUENCY AND PHASE REFERENCE The example above is illustrated in the following figure. SYSTEM VOLTAGES SYMMETRICAL COMPONENTS WYE VTs DELTA VTs 827844A1.CDR Figure 6–3: MEASUREMENT CONVENTION FOR SYMMETRICAL COMPONENTS GE Multilin F35 Multiple Feeder Protection System 6-15...
Page 356: Sources
SRC 1 RMS Ic: MESSAGE 0.000 SRC 1 RMS In: MESSAGE 0.000 SRC 1 PHASOR Ia: MESSAGE 0.000 0.0° SRC 1 PHASOR Ib: MESSAGE 0.000 0.0° SRC 1 PHASOR Ic: MESSAGE 0.000 0.0° 6-16 F35 Multiple Feeder Protection System GE Multilin...
Page 357 SRC 1 PHASOR Vcg: MESSAGE 0.000 0.0° SRC 1 RMS Vab: MESSAGE 0.00 SRC 1 RMS Vbc: MESSAGE 0.00 SRC 1 RMS Vca: MESSAGE 0.00 SRC 1 PHASOR Vab: MESSAGE 0.000 0.0° GE Multilin F35 Multiple Feeder Protection System 6-17...
Page 358 REACTIVE PWR MESSAGE φa: 0.000 SRC 1 REACTIVE PWR MESSAGE φb: 0.000 SRC 1 REACTIVE PWR MESSAGE φc: 0.000 SRC 1 APPARENT PWR MESSAGE 3φ: 0.000 SRC 1 APPARENT PWR MESSAGE φa: 0.000 6-18 F35 Multiple Feeder Protection System GE Multilin...
Page 359 Because energy values are accumulated, these values should be recorded and then reset immediately prior to changing CT or VT characteristics. h) DEMAND METERING    PATH: ACTUAL VALUES METERING SOURCE SRC 1 DEMAND  DEMAND SRC 1 DMD IA:  SRC 1 0.000 GE Multilin F35 Multiple Feeder Protection System 6-19...
Page 360 Maxi- mum demand quantities can be reset to zero with the  command. CLEAR RECORDS CLEAR DEMAND RECORDS 6-20 F35 Multiple Feeder Protection System GE Multilin...
Page 361 Voltage harmonics are calculated only for Wye connected phase VTs. Ensure the   SYSTEM SETUP AC INPUTS setting is “Wye” to enable voltage harmonics metering.  VOLTAGE BANK F5 PHASE VT XX CONNECTION NOTE GE Multilin F35 Multiple Feeder Protection System 6-21...
Page 362: Tracking Frequency
The tracking frequency is displayed here. The frequency is tracked based on the selection of the reference source with the setting in the   menu. Refer to the FREQUENCY AND PHASE REFERENCE SETTINGS SYSTEM SETUP POWER SYSTEM Power System section of chapter 5 for additional details. 6-22 F35 Multiple Feeder Protection System GE Multilin...
Page 363: Flexelements
2 for additional details. The IEC 61850 GGIO3 analog input data points are displayed in this menu. The GGIO3 analog data values are received via IEC 61850 GOOSE messages sent from other devices. GE Multilin F35 Multiple Feeder Protection System 6-23...
Page 364: Wattmetric Ground Fault
RTD INPUT xx  -50 °C Actual values for each RTD input channel that is enabled are displayed with the top line as the programmed channel ID and the bottom line as the value. 6-24 F35 Multiple Feeder Protection System GE Multilin...
Page 365: Records
COMMANDS CLEAR RECORDS Only major output operands generate events, not every operand. Elements that assert output per phase, for example, log operating phase output only without asserting the common three-phase operand event. GE Multilin F35 Multiple Feeder Protection System 6-25...
Page 366: Oscillography
It counts up at the defined sampling rate. If the data logger channels are defined, then both values are static. Refer to the  menu for clearing data logger records. COMMANDS CLEAR RECORDS 6-26 F35 Multiple Feeder Protection System GE Multilin...
Page 367: Breaker Maintenance
BKR 1 ARCING AMP  menu for clearing breaker arcing current records. The COMMANDS CLEAR RECORDS BREAKER OPERATING TIME defined as the slowest operating time of breaker poles that were initiated to open. GE Multilin F35 Multiple Feeder Protection System 6-27...
Page 368: Product Information
6.5PRODUCT INFORMATION 6.5.1 MODEL INFORMATION   PATH: ACTUAL VALUES PRODUCT INFO MODEL INFORMATION Range: standard GE Multilin order code format;  MODEL INFORMATION ORDER CODE LINE 1: example order code shown  F35-E00-HCH-F8F-H6G Range: standard GE Multilin order code format...
Page 369: Commands And
The states of up to 64 virtual inputs are changed here. The first line of the display indicates the ID of the virtual input. The second line indicates the current or selected status of the virtual input. This status will be a state off (logic 0) or on (logic 1). GE Multilin F35 Multiple Feeder Protection System...
Page 370 The complete date, as a minimum, must be entered to allow execution of this command. The new time (if entered) and date will take effect at the moment the ENTER key is clicked. The timescale of the entered time should be local time, including daylight time where and when applicable. F35 Multiple Feeder Protection System GE Multilin...
Page 371: Relay Maintenance
This allows the saved data to be as recent SAVE VOLATILE DATA as possible instead of relying on the periodic timer to save the data. GE Multilin F35 Multiple Feeder Protection System...
Page 372: Security
Operator Logoff: Selecting ‘Yes’ allows the Supervisor to forcefully logoff an operator session. • Clear Security Data: Selecting ‘Yes’ allows the Supervisor to forcefully clear all the security logs and clears all the operands associated with the self-tests. F35 Multiple Feeder Protection System GE Multilin...
Page 373: Targets Menu
The critical fail relay on the power supply module is de-energized. • All other output relays are de-energized and are prevented from further operation. • The faceplate In Service LED indicator is turned off. GE Multilin F35 Multiple Feeder Protection System...
Page 374 Most of the minor self-test errors can be disabled. Refer to the settings in the User-programmable self-tests section in the Settings chapter for additional details. MODULE FAILURE___: Contact Factory (xxx) • Latched target message: Yes. F35 Multiple Feeder Protection System GE Multilin...
Page 375 • What to do: Return the power supply module to GE Digital Energy for battery replacement. To instead dispose of the battery and power supply module, see the battery disposal information at the beginning of this manual.
Page 376 4L Discrepancy • Latched target message: No. • Description of problem: A discrepancy has been detected between the actual and desired state of a latching contact output of an installed type “4L” module. F35 Multiple Feeder Protection System GE Multilin...
Page 377 How often the test is performed: Event driven. • What to do: Contact the factory. d) WRONG TRANSCEIVER MESSAGES Description: The type of SFP does not match the CPU type. T-type CPU = All ports support fiber SFPs only GE Multilin F35 Multiple Feeder Protection System...
Page 378 Brick. Where multiple UR-series devices have self-test errors, look for common causes. 7-10 F35 Multiple Feeder Protection System GE Multilin...
Page 379 Brick output failing to respond to an output command can only be detected while the command is active, and so in this case the target is latched. A latched target can be unlatched by pressing the faceplate reset key if the command has ended, however the output may still be non-functional. GE Multilin F35 Multiple Feeder Protection System 7-11...
Page 380 7.2 TARGETS 7 COMMANDS AND TARGETS 7-12 F35 Multiple Feeder Protection System GE Multilin...
Page 381: Security
To add user accounts: Select the Security > User Management menu item to open the user management window. Enter a username in the User field. The username must be 4 to 20 characters in length. GE Multilin F35 Multiple Feeder Protection System...
Page 382: Modifying User Privileges
The EnerVista security management system must be enabled To modify user privileges: Select the Security > User Management menu item to open the user management window. Locate the username in the User field. F35 Multiple Feeder Protection System GE Multilin...
Page 383: Password Requirements
Password must contain characters from all of the following four categories: - English uppercase characters (A through Z) - English lowercase characters (a through z) - Base 10 digits (0 through 9) - Non-alphabetic characters (for example, ~, !, @, #, $,%, &) GE Multilin F35 Multiple Feeder Protection System...
Page 384: Cybersentry
(Administrator, Engineer, Supervisor, Observer, Operator) as login names and the associated passwords are stored on the UR device. As such, when using the local accounts, access is not user-attributable. F35 Multiple Feeder Protection System GE Multilin...
Page 385 All the other ports are closed. For example, Modbus is on by default, so its TCP port number, 502, is open. But if Modbus is disabled, port 502 is closed. This function has been tested and no unused ports have been found NOTE open. GE Multilin F35 Multiple Feeder Protection System...
Page 386: Security Menu
This setting must following (Shared) Secret meet the CyberSentry password password requirements. section for requirements RADIUS Authentication method used by RADIUS EAP-TTLS EAP-TTLS EAP-TTLS Administrator Authentication server. Currently fixed to EAP-TTLS. Method F35 Multiple Feeder Protection System GE Multilin...
Page 387 Change Text The specified role protected. All RADIUS users are password- following following Me1# and Administrator, protected. password password except for section for section for Supervisor, where requirements requireme it is only itself GE Multilin F35 Multiple Feeder Protection System...
Page 388 |--------------- Oscillography |--------------- Data Logger |--------------- Demand User Programmable |--------------- LEDs User Programmable |--------------- self test |--------------- Control Pushbuttons User programmable |--------------- Pushbuttons |--------------- Flex states User definable dis- |--------------- plays |--------------- Direct I/O F35 Multiple Feeder Protection System GE Multilin...
Page 389 |------------ Clear Records |------------ Set date and time User Displays Targets Actual Values |------------ Front Panel Labels Designer |------------ Status |------------ Metereing |------------ Transducer I/O |------------ Records |------------ Product Info Maintenance |------------ Modbus Analyzer GE Multilin F35 Multiple Feeder Protection System...
Page 390 Remote user IDs must reside on an external RADIUS server, and must be provided with the requisite user role (see the fol- lowing example). Users are specified in the RADIUS server configuration file for users. Roles are specified in the RADIUS server dictionary. Example: In the file ‘users’: exampleusername User-Password == "examplepassword" 8-10 F35 Multiple Feeder Protection System GE Multilin...
Page 391: Theory Of Operation
Depending on the fault type, appropriate voltage and current signals are selected from the phase quantities before applying the two equations above (the superscripts denote phases, the subscripts denote stations). For AG faults: ⋅ (EQ 9.7) GE Multilin F35 Multiple Feeder Protection System...
Page 392 -- - V (EQ 9.14) – – SYS0 -- - V – – SYS0 where Z is the equivalent zero-sequence impedance behind the relay as entered under the fault report setting menu. SYS0 F35 Multiple Feeder Protection System GE Multilin...
Page 393 FAULT TYPE FAULT FAULT LOCATION 3I_0 LOCATOR 1 FAULT# RECLOSE SHOT VA or VAB VB or VBC VC or VCA Vn or V_0 SHOT # FROM 827094A5.CDR AUTO RECLOSURE Figure 9–2: FAULT LOCATOR SCHEME GE Multilin F35 Multiple Feeder Protection System...
Page 394 9.1 FAULT LOCATOR 9 THEORY OF OPERATION F35 Multiple Feeder Protection System GE Multilin...
Page 395: Commissioning
The injected frequency should smoothly ramp through the set threshold, with the ramp starting frequency sufficiently out- side the threshold so the relay becomes conditioned to the trend before operation. For typical interconnected power sys- tems, the recommended testing ramp rate is 0.20 Hz/s. GE Multilin F35 Multiple Feeder Protection System 10-1...
Page 396 20 ms. The tracking frequency should not be used in timing measurements, as its algorithm involves phase locking, which purposely sets its frequency high or low to allow the F35 sample clock to catch-up or wait as necessary to reach synchro- nism with the power system. 10-2 F35 Multiple Feeder Protection System GE Multilin...
Page 397: Maintenance
Before performing this action, control power must be removed from the relay. Record the original loca- tion of the module to ensure that the same or replacement module is inserted into the correct slot. Modules with current input provide automatic shorting of external CT circuits. GE Multilin F35 Multiple Feeder Protection System 11-1...
Page 398 The new CT/VT modules can only be used with new CPUs; similarly, old CT/VT modules can only be used with old CPUs. In the event that there is a mismatch between the CPU and CT/VT module, the relay does not function and error displays. NOTE DSP ERROR HARDWARE MISMATCH 11-2 F35 Multiple Feeder Protection System GE Multilin...
Page 399: Batteries
10. Reinstall the battery clip and the metal cover, and reinsert the power supply module into the unit. 11. Power on the unit. 12. Dispose of the old battery as outlined in the next section. GE Multilin F35 Multiple Feeder Protection System 11-3...
Page 400: Dispose Of Battery
La batterie est marqué de ce symbole, qui comprennent les indications cadmium (Cd), plomb (Pb), ou mercure (Hg). Pour le recyclage, retourner la batterie à votre fournisseur ou à un point de collecte. Pour plus d'informations, voir: www.recyclethis.info. 11-4 F35 Multiple Feeder Protection System GE Multilin...
Page 401 Baterija je označena s tem simbolom, ki lahko vključuje napise, ki označujejo kadmij (Cd), svinec (Pb) ali živo srebro (Hg). Za ustrezno recikliranje baterijo vrnite dobavitelju ali jo odstranite na določenem zbirališču. Za več informacij obiščite spletno stran: www.recyclethis.info. GE Multilin F35 Multiple Feeder Protection System 11-5...
Page 402 Latin America +55 11 3614 1700 Europe, Middle East, Africa +(34) 94 485 88 00 Asia +86 21 2401 3208 India +91 80 41314617 From GE Part Number 1604-0021-A1, GE Publication Number GEK-113574 11-6 F35 Multiple Feeder Protection System GE Multilin...
Page 403: Uninstall And Clear Files And Data
Other files can be in standard formats, such as COMTRADE or .csv. You cannot erase directly the flash memory, but all records and settings in that memory can be deleted. Do this using the   command. SETTINGS PRODUCT SETUP CLEAR RELAY RECORDS GE Multilin F35 Multiple Feeder Protection System 11-7...
Page 404: Repairs
Customers are responsible for shipping costs to the factory, regardless of whether the unit is under warranty. • Fax a copy of the shipping information to the GE Digital Energy service department in Canada at +1 905 927 5098. Use the detailed return procedure outlined at https://www.gedigitalenergy.com/multilin/support/ret_proc.htm...
Page 405: Storage
Store the unit indoors in a cool, dry place. If possible, store in the original packaging. Follow the storage temperature range outlined in the Specifications. To avoid deterioration of electrolytic capacitors, power up units that are stored in a de-energized state once per year, for one hour continuously. GE Multilin F35 Multiple Feeder Protection System 11-9...
Page 406: Disposal
European Union, dispose of the battery as outlined earlier. To prevent non-intended use of the unit, remove the modules as outlined earlier, dismantle the unit, and recycle the metal when possible. 11-10 F35 Multiple Feeder Protection System GE Multilin...
Page 407: Parameter Lists
SRC 1 Igd Angle Degrees Source 1 differential ground current angle 6208 SRC 2 Ia RMS Amps Source 2 phase A current RMS 6210 SRC 2 Ib RMS Amps Source 2 phase B current RMS GE Multilin F35 Multiple Feeder Protection System...
Page 408 SRC 4 Ia RMS Amps Source 4 phase A current RMS 6338 SRC 4 Ib RMS Amps Source 4 phase B current RMS 6340 SRC 4 Ic RMS Amps Source 4 phase C current RMS F35 Multiple Feeder Protection System GE Multilin...
Page 409 SRC 6 Ib RMS Amps Source 6 phase B current RMS 6468 SRC 6 Ic RMS Amps Source 6 phase C current RMS 6470 SRC 6 In RMS Amps Source 6 neutral current RMS GE Multilin F35 Multiple Feeder Protection System...
Page 410 SRC 1 V_2 Mag Volts Source 1 negative-sequence voltage magnitude 6699 SRC 1 V_2 Angle Degrees Source 1 negative-sequence voltage angle 6720 SRC 2 Vag RMS Volts Source 2 phase AG voltage RMS F35 Multiple Feeder Protection System GE Multilin...
Page 411 6814 SRC 3 Vx RMS Volts Source 3 auxiliary voltage RMS 6816 SRC 3 Vx Mag Volts Source 3 auxiliary voltage magnitude 6818 SRC 3 Vx Angle Degrees Source 3 auxiliary voltage angle GE Multilin F35 Multiple Feeder Protection System...
Page 412 SRC 5 Vca RMS Volts Source 5 phase CA voltage RMS 6933 SRC 5 Vab Mag Volts Source 5 phase AB voltage magnitude 6935 SRC 5 Vab Angle Degrees Source 5 phase AB voltage angle F35 Multiple Feeder Protection System GE Multilin...
Page 413 Source 1 phase C real power 7176 SRC 1 Q Vars Source 1 three-phase reactive power 7178 SRC 1 Qa Vars Source 1 phase A reactive power 7180 SRC 1 Qb Vars Source 1 phase B reactive power GE Multilin F35 Multiple Feeder Protection System...
Page 414 Source 4 phase B real power 7270 SRC 4 Pc Watts Source 4 phase C real power 7272 SRC 4 Q Vars Source 4 three-phase reactive power 7274 SRC 4 Qa Vars Source 4 phase A reactive power F35 Multiple Feeder Protection System GE Multilin...
Page 415 SRC 1 Frequency Source 1 frequency 7554 SRC 2 Frequency Source 2 frequency 7556 SRC 3 Frequency Source 3 frequency 7558 SRC 4 Frequency Source 4 frequency 7560 SRC 5 Frequency Source 5 frequency GE Multilin F35 Multiple Feeder Protection System...
Page 416 Fault 1 pre-fault phase A voltage angle 9036 Prefault Vb Mag [0] Volts Fault 1 pre-fault phase B voltage magnitude 9038 Prefault Vb Ang [0] Degrees Fault 1 pre-fault phase B voltage angle A-10 F35 Multiple Feeder Protection System GE Multilin...
Page 417 Fault 3 pre-fault phase B current magnitude 9105 Prefault Ib Ang [2] Degrees Fault 3 pre-fault phase B current angle 9106 Prefault Ic Mag [2] Amps Fault 3 pre-fault phase C current magnitude GE Multilin F35 Multiple Feeder Protection System A-11...
Page 418 Fault 4 post-fault phase C voltage magnitude 9173 Postfault Vc Ang [3] Degrees Fault 4 post-fault phase C voltage angle 9174 Fault Type [3] Fault 4 type 9175 Fault Location [3] Fault 4 location A-12 F35 Multiple Feeder Protection System GE Multilin...
Page 419 DCmA input 17 actual value 13538 DCmA Inputs 18 Value DCmA input 18 actual value 13540 DCmA Inputs 19 Value DCmA input 19 actual value 13542 DCmA Inputs 20 Value DCmA input 20 actual value GE Multilin F35 Multiple Feeder Protection System A-13...
Page 420 RTD input 40 actual value 13592 RTD Inputs 41 Value RTD input 41 actual value 13593 RTD Inputs 42 Value RTD input 42 actual value 13594 RTD Inputs 43 Value RTD input 43 actual value A-14 F35 Multiple Feeder Protection System GE Multilin...
Page 421 GOOSE Analog In 7 IEC 61850 GOOSE analog input 7 45598 GOOSE Analog In 8 IEC 61850 GOOSE analog input 8 45600 GOOSE Analog In 9 IEC 61850 GOOSE analog input 9 GE Multilin F35 Multiple Feeder Protection System A-15...
Page 422: Flexinteger Items
IEC61850 GOOSE UInteger input 13 9994 GOOSE UInt Input 14 IEC61850 GOOSE UInteger input 14 9996 GOOSE UInt Input 15 IEC61850 GOOSE UInteger input 15 9998 GOOSE UInt Input 16 IEC61850 GOOSE UInteger input 16 A-16 F35 Multiple Feeder Protection System GE Multilin...
Page 423: Modbus Rtu Protocol
See the Supported Function Codes section for complete details. An exception response from the slave is indi- cated by setting the high order bit of the function code in the response packet. See the Exception Responses section for further details. GE Multilin F35 Multiple Feeder Protection System...
Page 424: Modbus Rtu Crc-16 Algorithm
This algorithm requires the characteristic polynomial to be reverse bit ordered. The most significant bit of the characteristic polynomial is dropped, since it does not affect the value of the remainder. A C programming language implementation of the CRC algorithm will be provided upon request. F35 Multiple Feeder Protection System GE Multilin...
Page 425 No: go to 8; Yes: G (+) A --> A and continue. Is j = 8? No: go to 5; Yes: continue i + 1 --> i Is i = N? No: go to 3; Yes: continue A --> CRC GE Multilin F35 Multiple Feeder Protection System...
Page 426: Modbus Function Codes
Modbus officially defines function codes from 1 to 127 though only a small subset is generally needed. The relay supports some of these functions, as summarized in the following table. Subsequent sections describe each function code in detail. FUNCTION CODE MODBUS DEFINITION GE MULTILIN DEFINITION Read holding registers Read actual values or settings Read holding registers...
Page 427: Execute Operation (Function Code 05H
DATA STARTING ADDRESS - low DATA STARTING ADDRESS - low DATA - high DATA - high DATA - low DATA - low CRC - low CRC - low CRC - high CRC - high GE Multilin F35 Multiple Feeder Protection System...
Page 428: Store Multiple Settings (Function Code 10H
PACKET FORMAT EXAMPLE (HEX) SLAVE ADDRESS SLAVE ADDRESS FUNCTION CODE FUNCTION CODE CRC - low order byte ERROR CODE CRC - high order byte CRC - low order byte CRC - high order byte F35 Multiple Feeder Protection System GE Multilin...
Page 429: File Transfers
Cleared Date to the present date and time. To read binary COMTRADE oscillography files, read the following filenames: OSCnnnn.CFG and OSCnnn.DAT Replace “nnn” with the desired oscillography trigger number. For ASCII format, use the following file names OSCAnnnn.CFG and OSCAnnn.DAT GE Multilin F35 Multiple Feeder Protection System...
Page 430 EVTnnn.TXT (replace nnn with the desired starting record number) To read from a specific record to another specific record, use the following filename: EVT.TXT xxxxx yyyyy (replace xxxxx with the starting record number and yyyyy with the ending record number) F35 Multiple Feeder Protection System GE Multilin...
Page 431: Memory Mapping
040E Virtual Input 15 State 0 to 1 F108 0 (Off) 040F Virtual Input 16 State 0 to 1 F108 0 (Off) 0410 Virtual Input 17 State 0 to 1 F108 0 (Off) GE Multilin F35 Multiple Feeder Protection System...
Page 432 -2147483647 to F004 2147483647 0804 Digital Counter 1 Frozen Time Stamp 0 to 4294967295 F050 0806 Digital Counter 1 Frozen Time Stamp us (microsecond part 0 to 4294967295 F003 of time stamp) B-10 F35 Multiple Feeder Protection System GE Multilin...
Page 433 Field Unit Contact Input Output Operand States (8 items) 0 to 65535 F500 15EB Field Contact Output Physical States (8 items) 0 to 65535 F500 15F3 Field Contact Output Current States (8 items) 0 to 65535 F500 GE Multilin F35 Multiple Feeder Protection System B-11...
Page 434 Source 1 Neutral Current Magnitude 0 to 999999.999 0.001 F060 1813 Source 1 Neutral Current Angle -359.9 to 0 degrees F002 1814 Source 1 Ground Current RMS 0 to 999999.999 0.001 F060 B-12 F35 Multiple Feeder Protection System GE Multilin...
Page 436 Source 1 Demand Watt 0 to 999999.999 0.001 F060 1E08 Source 1 Demand Var 0 to 999999.999 0.001 F060 1E0A Source 1 Demand Va 0 to 999999.999 0.001 F060 1E0C Reserved (4 items) F001 B-14 F35 Multiple Feeder Protection System GE Multilin...
Page 438 Autoreclose 5 Count 0 to 65535 F001 2415 Autoreclose 6 Count 0 to 65535 F001 Field Unit Raw Data Settings (Read/Write Setting) 2460 Field Raw Data Port 0 to 7 F244 6 (H1a) B-16 F35 Multiple Feeder Protection System GE Multilin...
Page 439 Expanded Remote Input/Output Status (Read Only) 2F00 Remote Device States, one per register (32 items) 0 to 1 F155 0 (Offline) 2F80 Remote Input States, one per register (64 items) 0 to 1 F108 0 (Off) GE Multilin F35 Multiple Feeder Protection System B-17...
Page 440 Security (Read Only) 32B4 Engineer Alphanumeric Password Status 0 to 1 F102 0 (Disabled) Security (Read/Write) 32B5 Engineer Alphanumeric Password Entry F202 (none) Security (Read/Write Setting) 32BF Operator Alphanumeric Password Setting F202 (none) B-18 F35 Multiple Feeder Protection System GE Multilin...
Page 441 0.001 F004 34C8 DCmA Inputs 5 Value -9999.999 to 9999.999 0.001 F004 34CA DCmA Inputs 6 Value -9999.999 to 9999.999 0.001 F004 34CC DCmA Inputs 7 Value -9999.999 to 9999.999 0.001 F004 GE Multilin F35 Multiple Feeder Protection System B-19...
Page 442 °C F002 3511 RTD Input 34 Value -32768 to 32767 °C F002 3512 RTD Input 35 Value -32768 to 32767 °C F002 3513 RTD Input 36 Value -32768 to 32767 °C F002 B-20 F35 Multiple Feeder Protection System GE Multilin...
Page 443 PTP - IRIG-B Delta FlexAnalog -262143 to 262143 F004 Field Units (Read/Write Setting) (8 modules) 3800 Field Unit 1 ID 0 to 1 F205 "U1" 3806 Field Unit 1 Function 0 to 1 F102 0 (Disabled) GE Multilin F35 Multiple Feeder Protection System B-21...
Page 446 Field Unit RTD 1 Origin 0 to 24 F253 0 (None) 3F07 Field Unit RTD 1 Type 0 to 2 F259 0 (100 Ohm Nickel) 3F08 ...Repeated for Field Unit RTD 2 B-24 F35 Multiple Feeder Protection System GE Multilin...
Page 447 0 to 1 F102 0 (Disabled) Passwords (Read/Write Setting) 402F Local Setting Auth 1 to 4294967295 F300 4031 Remote Setting Auth 0 to 4294967295 F300 4033 Access Auth Timeout 5 to 480 F001 GE Multilin F35 Multiple Feeder Protection System B-25...
Page 448 2 (1) 40B4 DNP Current Default Deadband 0 to 100000000 F003 30000 40B6 DNP Voltage Default Deadband 0 to 100000000 F003 30000 40B8 DNP Power Default Deadband 0 to 100000000 F003 30000 B-26 F35 Multiple Feeder Protection System GE Multilin...
Page 449 Ethernet Switch Port 3 Events 0 to 1 F102 0 (Disabled) 414E Ethernet Switch Port 4 Events 0 to 1 F102 0 (Disabled) 414F Ethernet Switch Port 5 Events 0 to 1 F102 0 (Disabled) GE Multilin F35 Multiple Feeder Protection System B-27...
Page 450 Oscillography Number of Records 3 to 64 F001 41C1 Oscillography Trigger Mode 0 to 1 F118 0 (Auto. Overwrite) 41C2 Oscillography Trigger Position 0 to 100 F001 41C3 Oscillography Trigger Source 0 to 4294967295 F300 B-28 F35 Multiple Feeder Protection System GE Multilin...
Page 452 Source 1 Auxiliary VT 0 to 63 F400 4587 ...Repeated for Source 2 458E ...Repeated for Source 3 4595 ...Repeated for Source 4 459C ...Repeated for Source 5 45A3 ...Repeated for Source 6 B-30 F35 Multiple Feeder Protection System GE Multilin...
Page 453 490A Demand Current Method 0 to 2 F139 0 (Thermal Exponential) 490B Demand Power Method 0 to 2 F139 0 (Thermal Exponential) 490C Demand Interval 0 to 5 F132 2 (15 MIN) GE Multilin F35 Multiple Feeder Protection System B-31...
Page 454 Raw Field Data Brick ADC Temperature 0 to 1 degree F002 4E20 Raw Field Data Brick Transceiver Temperature 0 to 1 degree F002 4E21 Raw Field Data Brick Transceiver Voltage 0 to 0.01 0.01 F001 B-32 F35 Multiple Feeder Protection System GE Multilin...
Page 456 58F0 ...Repeated for FlexLogic Timer 31 58F8 ...Repeated for FlexLogic Timer 32 Phase Time Overcurrent (Read/Write Grouped Setting) (6 modules) 5900 Phase Time Overcurrent 1 Function 0 to 1 F102 0 (Disabled) B-34 F35 Multiple Feeder Protection System GE Multilin...
Page 459 Autoreclose 1 Dead Time Shot 3 0 to 655.35 0.01 F001 6214 Autoreclose 1 Dead Time Shot 4 0 to 655.35 0.01 F001 6215 Autoreclose 1 Reset Lockout Delay 0 to 655.35 0.01 F001 6000 GE Multilin F35 Multiple Feeder Protection System B-37...
Page 460 Phase Undervoltage 1 Measurement Mode 0 to 1 F186 0 (Phase to Ground) 700B Reserved (6 items) 0 to 1 F001 7013 ...Repeated for Phase Undervoltage 2 7022 ...Repeated for Phase Undervoltage 3 B-38 F35 Multiple Feeder Protection System GE Multilin...
Page 462 Underfrequency 1 Reserved (5 items) 0 to 1 F001 7A8F ...Repeated for Underfrequency 2 7A9E ...Repeated for Underfrequency 3 7AAD ...Repeated for Underfrequency 4 7ABC ...Repeated for Underfrequency 5 7ACB ...Repeated for Underfrequency 6 B-40 F35 Multiple Feeder Protection System GE Multilin...
Page 463 0 (Definite Time) 7F65 Auxiliary Undervoltage 1 Minimum Voltage 0 to 3 0.001 F001 7F66 Auxiliary Undervoltage 1 Block 0 to 4294967295 F300 7F68 Auxiliary Undervoltage 1 Target 0 to 2 F109 0 (Self-reset) GE Multilin F35 Multiple Feeder Protection System B-41...
Page 464 EGD Fast Producer Exchange 1 Data Rate 50 to 1000 F001 1000 8404 EGD Fast Producer Exchange 1 Data Item 1 (20 items) 0 to 65535 F001 8418 Reserved (80 items) F001 B-42 F35 Multiple Feeder Protection System GE Multilin...
Page 468 FlexElement Actual Values (Read Only) (16 modules) 9000 FlexElement 1 Actual 0.001 F004 -2147483.647 to 2147483.647 9902 FlexElement 2 Actual 0.001 F004 -2147483.647 to 2147483.647 9904 FlexElement 3 Actual -2147483.647 to 2147483.647 0.001 F004 B-46 F35 Multiple Feeder Protection System GE Multilin...
Page 469 0 (Off) 9AD0 Teleprotection Input 2 States, 1 per register (16 items) 0 to 1 F108 0 (Off) Selector Switch Actual Values (Read Only) A210 Selector Switch 1 Position 1 to 7 F001 GE Multilin F35 Multiple Feeder Protection System B-47...
Page 470 0 to 600 0.01 F001 A50B PID 1 Deriv Time Const 0 to 600 0.01 F001 A50C PID 1 Derivative Limit 1 to 20 F001 A50D PID 1 Max -10000 to 10000 F002 B-48 F35 Multiple Feeder Protection System GE Multilin...
Page 472 F206 (none) AD55 IEC 61850 Logical Node PTRCx Name Prefix (6 items) 0 to 65534 F206 (none) AD67 IEC 61850 Logical Node PDIFx Name Prefix (4 items) 0 to 65534 F206 (none) B-50 F35 Multiple Feeder Protection System GE Multilin...
Page 473 0 to 7 F001 B068 IEC 61850 GOOSE VLAN ID 0 to 4095 F001 B069 IEC 61850 GOOSE ETYPE APPID 0 to 16383 F001 B06A Reserved (2 items) 0 to 1 F001 GE Multilin F35 Multiple Feeder Protection System B-51...
Page 476 0 to 197 F233 0 (None) (32 items) B920 ...Repeated for module number 2 B940 ...Repeated for module number 3 B960 ...Repeated for module number 4 B980 ...Repeated for module number 5 B-54 F35 Multiple Feeder Protection System GE Multilin...
Page 484 Remote Device 1 GOOSE Ethernet APPID 0 to 16383 F001 CB22 Remote Device 1 GOOSE Dataset 0 to 16 F184 0 (Fixed) CB23 Remote Device 1 in PMU Scheme 0 to 1 F126 0 (No) B-62 F35 Multiple Feeder Protection System GE Multilin...
Page 487 IEC 61850 GGIO2.CF.SPCSO36.ctlModel Value 0 to 2 F001 D344 IEC 61850 GGIO2.CF.SPCSO37.ctlModel Value 0 to 2 F001 D345 IEC 61850 GGIO2.CF.SPCSO38.ctlModel Value 0 to 2 F001 D346 IEC 61850 GGIO2.CF.SPCSO39.ctlModel Value 0 to 2 F001 GE Multilin F35 Multiple Feeder Protection System B-65...
Page 488 0 to 1 F102 1 (Enabled) DC9D Latching Output 1 Type 0 to 1 F090 0 (Operate- dominant) DC9E Reserved F001 DC9F ...Repeated for Contact Output 2 DCAE ...Repeated for Contact Output 3 B-66 F35 Multiple Feeder Protection System GE Multilin...
Page 490 Reserved F205 (none) Setting File Template (Read Only Non-Volatile) ED07 Last Settings Change Date 0 to 4294967295 F050 Settings File Template (Read/Write Setting) ED09 Template Bitmask (750 items) 0 to 65535 F001 B-68 F35 Multiple Feeder Protection System GE Multilin...
Page 491: Data Formats
0 = Disabled, 1 = Enabled UR_UINT32 TIME in SR format (alternate format for F050) First 16 bits are Hours/Minutes (HH:MM:xx.xxx). Hours: 0=12am, 1=1am,...,12=12pm,...23=11pm; Minutes: 0 to 59 in steps of 1 GE Multilin F35 Multiple Feeder Protection System B-69...
Page 492 F113 0.84 2.70 5.70 19.50 ENUMERATION: PARITY 0.86 2.80 5.80 20.00 0 = None, 1 = Odd, 2 = Even F122 ENUMERATION: ELEMENT INPUT SIGNAL TYPE 0 = Phasor, 1 = RMS B-70 F35 Multiple Feeder Protection System GE Multilin...
Page 493 Ground Instantaneous Overcurrent 5 Underfrequency 4 Ground Instantaneous Overcurrent 6 Underfrequency 5 Ground Instantaneous Overcurrent 7 Underfrequency 6 Ground Instantaneous Overcurrent 8 Selector switch 1 Ground Instantaneous Overcurrent 9 Selector switch 2 GE Multilin F35 Multiple Feeder Protection System B-71...
Page 494 Digital Element 48 Digital Counter 4 Trip Bus 1 Digital Counter 5 Trip Bus 2 Digital Counter 6 Trip Bus 3 Digital Counter 7 Trip Bus 4 Digital Counter 8 Trip Bus 5 B-72 F35 Multiple Feeder Protection System GE Multilin...
Page 495 Incipient cable fault detector 4 User-Programmable Pushbutton 1 Incipient cable fault detector 5 User-Programmable Pushbutton 2 Incipient cable fault detector 6 User-Programmable Pushbutton 3 1005 PID 1 User-Programmable Pushbutton 4 1006 PID 2 GE Multilin F35 Multiple Feeder Protection System B-73...
Page 496 0 = Not Programmed, 1 = Programmed Maintenance Alert Any Minor Error F134 Any Major Error ENUMERATION: PASS/FAIL Maintenance Alert 0 = Fail, 1 = OK, 2 = n/a Maintenance Alert IEC 61850 Data Set B-74 F35 Multiple Feeder Protection System GE Multilin...
Page 497 A bit value of 0 = no error, 1 = error System Integrity Recovery 07 F144 F147 ENUMERATION: FORCED CONTACT INPUT STATE ENUMERATION: LINE LENGTH UNITS 0 = Disabled, 1 = Open, 2 = Closed 0 = km, 1 = miles GE Multilin F35 Multiple Feeder Protection System B-75...
Page 498 F174 DNA-23 UserSt-26 ENUMERATION: TRANSDUCER RTD INPUT TYPE DNA-24 UserSt-27 0 = 100 Ohm Platinum, 1 = 120 Ohm Nickel, DNA-25 UserSt-28 2 = 100 Ohm Nickel, 3 = 10 Ohm Copper B-76 F35 Multiple Feeder Protection System GE Multilin...
Page 499 20 registers, 16 Bits: 1st Char MSB, 2nd Char LSB F202 TEXT20: 20-CHARACTER ASCII TEXT 10 registers, 16 Bits: 1st Char MSB, 2nd Char LSB F203 TEXT16: 16-CHARACTER ASCII TEXT F204 TEXT80: 80-CHARACTER ASCII TEXT GE Multilin F35 Multiple Feeder Protection System B-77...
Page 500 MMXU1.MX.TotW.mag.f MMXU2.MX.PhV.phsC.cVal.ang.f MMXU1.MX.TotVAr.mag.f MMXU2.MX.A.phsA.cVal.mag.f MMXU1.MX.TotVA.mag.f MMXU2.MX.A.phsA.cVal.ang.f MMXU1.MX.TotPF.mag.f MMXU2.MX.A.phsB.cVal.mag.f MMXU1.MX.Hz.mag.f MMXU2.MX.A.phsB.cVal.ang.f MMXU1.MX.PPV.phsAB.cVal.mag.f MMXU2.MX.A.phsC.cVal.mag.f MMXU1.MX.PPV.phsAB.cVal.ang.f MMXU2.MX.A.phsC.cVal.ang.f MMXU1.MX.PPV.phsBC.cVal.mag.f MMXU2.MX.A.neut.cVal.mag.f MMXU1.MX.PPV.phsBC.cVal.ang.f MMXU2.MX.A.neut.cVal.ang.f MMXU1.MX.PPV.phsCA.cVal.mag.f MMXU2.MX.W.phsA.cVal.mag.f MMXU1.MX.PPV.phsCA.cVal.ang.f MMXU2.MX.W.phsB.cVal.mag.f MMXU1.MX.PhV.phsA.cVal.mag.f MMXU2.MX.W.phsC.cVal.mag.f MMXU1.MX.PhV.phsA.cVal.ang.f MMXU2.MX.VAr.phsA.cVal.mag.f MMXU1.MX.PhV.phsB.cVal.mag.f MMXU2.MX.VAr.phsB.cVal.mag.f MMXU1.MX.PhV.phsB.cVal.ang.f MMXU2.MX.VAr.phsC.cVal.mag.f MMXU1.MX.PhV.phsC.cVal.mag.f MMXU2.MX.VA.phsA.cVal.mag.f B-78 F35 Multiple Feeder Protection System GE Multilin...
Page 501 MMXU3.MX.VA.phsB.cVal.mag.f MMXU5.MX.PhV.phsA.cVal.mag.f MMXU3.MX.VA.phsC.cVal.mag.f MMXU5.MX.PhV.phsA.cVal.ang.f MMXU3.MX.PF.phsA.cVal.mag.f MMXU5.MX.PhV.phsB.cVal.mag.f MMXU3.MX.PF.phsB.cVal.mag.f MMXU5.MX.PhV.phsB.cVal.ang.f MMXU3.MX.PF.phsC.cVal.mag.f MMXU5.MX.PhV.phsC.cVal.mag.f MMXU4.MX.TotW.mag.f MMXU5.MX.PhV.phsC.cVal.ang.f MMXU4.MX.TotVAr.mag.f MMXU5.MX.A.phsA.cVal.mag.f MMXU4.MX.TotVA.mag.f MMXU5.MX.A.phsA.cVal.ang.f MMXU4.MX.TotPF.mag.f MMXU5.MX.A.phsB.cVal.mag.f MMXU4.MX.Hz.mag.f MMXU5.MX.A.phsB.cVal.ang.f MMXU4.MX.PPV.phsAB.cVal.mag.f MMXU5.MX.A.phsC.cVal.mag.f MMXU4.MX.PPV.phsAB.cVal.ang.f MMXU5.MX.A.phsC.cVal.ang.f MMXU4.MX.PPV.phsBC.cVal.mag.f MMXU5.MX.A.neut.cVal.mag.f MMXU4.MX.PPV.phsBC.cVal.ang.f MMXU5.MX.A.neut.cVal.ang.f MMXU4.MX.PPV.phsCA.cVal.mag.f MMXU5.MX.W.phsA.cVal.mag.f MMXU4.MX.PPV.phsCA.cVal.ang.f MMXU5.MX.W.phsB.cVal.mag.f GE Multilin F35 Multiple Feeder Protection System B-79...
Page 502 MMXU6.MX.W.phsC.cVal.mag.f GGIO5.ST.UIntIn6.stVal MMXU6.MX.VAr.phsA.cVal.mag.f GGIO5.ST.UIntIn7.q MMXU6.MX.VAr.phsB.cVal.mag.f GGIO5.ST.UIntIn7.stVal MMXU6.MX.VAr.phsC.cVal.mag.f GGIO5.ST.UIntIn8.q MMXU6.MX.VA.phsA.cVal.mag.f GGIO5.ST.UIntIn8.stVal MMXU6.MX.VA.phsB.cVal.mag.f GGIO5.ST.UIntIn9.q MMXU6.MX.VA.phsC.cVal.mag.f GGIO5.ST.UIntIn9.stVal MMXU6.MX.PF.phsA.cVal.mag.f GGIO5.ST.UIntIn10.q MMXU6.MX.PF.phsB.cVal.mag.f GGIO5.ST.UIntIn10.stVal MMXU6.MX.PF.phsC.cVal.mag.f GGIO5.ST.UIntIn11.q GGIO4.MX.AnIn1.mag.f GGIO5.ST.UIntIn11.stVal GGIO4.MX.AnIn2.mag.f GGIO5.ST.UIntIn12.q GGIO4.MX.AnIn3.mag.f GGIO5.ST.UIntIn12.stVal GGIO4.MX.AnIn4.mag.f GGIO5.ST.UIntIn13.q GGIO4.MX.AnIn5.mag.f GGIO5.ST.UIntIn13.stVal GGIO4.MX.AnIn6.mag.f GGIO5.ST.UIntIn14.q B-80 F35 Multiple Feeder Protection System GE Multilin...
Page 503 ENUMERATION: WATTMETRIC GROUND FAULT VOLTAGE GGIO3.MX.AnIn22.mag.f GGIO3.MX.AnIn23.mag.f Value Voltage GGIO3.MX.AnIn24.mag.f Calculated VN GGIO3.MX.AnIn25.mag.f Measured VX GGIO3.MX.AnIn26.mag.f GGIO3.MX.AnIn27.mag.f F235 GGIO3.MX.AnIn28.mag.f ENUMERATION: WATTMETRIC GROUND FAULT CURRENT GGIO3.MX.AnIn29.mag.f GGIO3.MX.AnIn30.mag.f Value Current GGIO3.MX.AnIn31.mag.f Calculated IN GGIO3.MX.AnIn32.mag.f Measured IG GE Multilin F35 Multiple Feeder Protection System B-81...
Page 504 Saturday U2/AC1..3 U2/AC5..7 U3/AC1..3 F239 ENUMERATION: REAL TIME CLOCK DAYLIGHT SAVINGS U3/AC5..7 TIME START DAY INSTANCE U4/AC1..3 U4/AC5..7 Value Instance U5/AC1..3 First U5/AC5..7 Second U6/AC1..3 Third U6/AC5..7 Fourth U7/AC1..3 Last U7/AC5..7 U8/AC1..3 B-82 F35 Multiple Feeder Protection System GE Multilin...
Page 505 [2] CONTACT INPUTS (1 to 96) [3] CONTACT INPUTS OFF (1 to 96) None [4] VIRTUAL INPUTS (1 to 32) [6] VIRTUAL OUTPUTS (1 to 64) [8] CONTACT OUTPUTS [10] CONTACT OUTPUTS VOLTAGE DETECTED (1 to 64) GE Multilin F35 Multiple Feeder Protection System B-83...
Page 506 0 to 15 corresponding to input/output state 33 to 48 (if required). The fourth register indicates input/out- put state with bits 0 to 15 corresponding to input/output state 49 to 64 (if required). B-84 F35 Multiple Feeder Protection System GE Multilin...
Page 507 UR_UINT16: FLEXANALOG PARAMETER Corresponds to the Modbus address of the value used when this parameter is selected. Only certain values can be used as FlexAn- alogs (basically all metering quantities used in protection). GE Multilin F35 Multiple Feeder Protection System B-85...
Page 508 PIOC3.ST.Str.general PIOC29.ST.Op.general PIOC3.ST.Op.general PIOC30.ST.Str.general PIOC4.ST.Str.general PIOC30.ST.Op.general PIOC4.ST.Op.general PIOC31.ST.Str.general PIOC5.ST.Str.general PIOC31.ST.Op.general PIOC5.ST.Op.general PIOC32.ST.Str.general PIOC6.ST.Str.general PIOC32.ST.Op.general PIOC6.ST.Op.general PIOC33.ST.Str.general PIOC7.ST.Str.general PIOC33.ST.Op.general PIOC7.ST.Op.general PIOC34.ST.Str.general PIOC8.ST.Str.general PIOC34.ST.Op.general PIOC8.ST.Op.general PIOC35.ST.Str.general PIOC9.ST.Str.general PIOC35.ST.Op.general PIOC9.ST.Op.general PIOC36.ST.Str.general PIOC10.ST.Str.general PIOC36.ST.Op.general PIOC10.ST.Op.general PIOC37.ST.Str.general B-86 F35 Multiple Feeder Protection System GE Multilin...
Page 509 PIOC56.ST.Str.general PTOC10.ST.Op.general PIOC56.ST.Op.general PTOC11.ST.Str.general PIOC57.ST.Str.general PTOC11.ST.Op.general PIOC57.ST.Op.general PTOC12.ST.Str.general PIOC58.ST.Str.general PTOC12.ST.Op.general PIOC58.ST.Op.general PTOC13.ST.Str.general PIOC59.ST.Str.general PTOC13.ST.Op.general PIOC59.ST.Op.general PTOC14.ST.Str.general PIOC60.ST.Str.general PTOC14.ST.Op.general PIOC60.ST.Op.general PTOC15.ST.Str.general PIOC61.ST.Str.general PTOC15.ST.Op.general PIOC61.ST.Op.general PTOC16.ST.Str.general PIOC62.ST.Str.general PTOC16.ST.Op.general PIOC62.ST.Op.general PTOC17.ST.Str.general PIOC63.ST.Str.general PTOC17.ST.Op.general PIOC63.ST.Op.general PTOC18.ST.Str.general GE Multilin F35 Multiple Feeder Protection System B-87...
Page 510 PTRC3.ST.Tr.general RBRF10.ST.OpIn.general PTRC3.ST.Op.general RBRF11.ST.OpEx.general PTRC4.ST.Tr.general RBRF11.ST.OpIn.general PTRC4.ST.Op.general RBRF12.ST.OpEx.general PTRC5.ST.Tr.general RBRF12.ST.OpIn.general PTRC5.ST.Op.general RBRF13.ST.OpEx.general PTRC6.ST.Tr.general RBRF13.ST.OpIn.general PTRC6.ST.Op.general RBRF14.ST.OpEx.general PTUV1.ST.Str.general RBRF14.ST.OpIn.general PTUV1.ST.Op.general RBRF15.ST.OpEx.general PTUV2.ST.Str.general RBRF15.ST.OpIn.general PTUV2.ST.Op.general RBRF16.ST.OpEx.general PTUV3.ST.Str.general RBRF16.ST.OpIn.general PTUV3.ST.Op.general RBRF17.ST.OpEx.general PTUV4.ST.Str.general RBRF17.ST.OpIn.general PTUV4.ST.Op.general RBRF18.ST.OpEx.general B-88 F35 Multiple Feeder Protection System GE Multilin...
Page 511 CSWI3.ST.Loc.stVal CSWI29.ST.Pos.stVal CSWI3.ST.Pos.stVal CSWI30.ST.Loc.stVal CSWI4.ST.Loc.stVal CSWI30.ST.Pos.stVal CSWI4.ST.Pos.stVal GGIO1.ST.Ind1.stVal CSWI5.ST.Loc.stVal GGIO1.ST.Ind2.stVal CSWI5.ST.Pos.stVal GGIO1.ST.Ind3.stVal CSWI6.ST.Loc.stVal GGIO1.ST.Ind4.stVal CSWI6.ST.Pos.stVal GGIO1.ST.Ind5.stVal CSWI7.ST.Loc.stVal GGIO1.ST.Ind6.stVal CSWI7.ST.Pos.stVal GGIO1.ST.Ind7.stVal CSWI8.ST.Loc.stVal GGIO1.ST.Ind8.stVal CSWI8.ST.Pos.stVal GGIO1.ST.Ind9.stVal CSWI9.ST.Loc.stVal GGIO1.ST.Ind10.stVal CSWI9.ST.Pos.stVal GGIO1.ST.Ind11.stVal CSWI10.ST.Loc.stVal GGIO1.ST.Ind12.stVal CSWI10.ST.Pos.stVal GGIO1.ST.Ind13.stVal GE Multilin F35 Multiple Feeder Protection System B-89...
Page 512 GGIO1.ST.Ind51.stVal GGIO1.ST.Ind104.stVal GGIO1.ST.Ind52.stVal GGIO1.ST.Ind105.stVal GGIO1.ST.Ind53.stVal GGIO1.ST.Ind106.stVal GGIO1.ST.Ind54.stVal GGIO1.ST.Ind107.stVal GGIO1.ST.Ind55.stVal GGIO1.ST.Ind108.stVal GGIO1.ST.Ind56.stVal GGIO1.ST.Ind109.stVal GGIO1.ST.Ind57.stVal GGIO1.ST.Ind110.stVal GGIO1.ST.Ind58.stVal GGIO1.ST.Ind111.stVal GGIO1.ST.Ind59.stVal GGIO1.ST.Ind112.stVal GGIO1.ST.Ind60.stVal GGIO1.ST.Ind113.stVal GGIO1.ST.Ind61.stVal GGIO1.ST.Ind114.stVal GGIO1.ST.Ind62.stVal GGIO1.ST.Ind115.stVal GGIO1.ST.Ind63.stVal GGIO1.ST.Ind116.stVal GGIO1.ST.Ind64.stVal GGIO1.ST.Ind117.stVal GGIO1.ST.Ind65.stVal GGIO1.ST.Ind118.stVal GGIO1.ST.Ind66.stVal GGIO1.ST.Ind119.stVal B-90 F35 Multiple Feeder Protection System GE Multilin...
Page 513 MMXU1.MX.VAr.phsA.cVal.mag.f MMXU3.MX.PPV.phsBC.cVal.mag.f MMXU1.MX.VAr.phsB.cVal.mag.f MMXU3.MX.PPV.phsBC.cVal.ang.f MMXU1.MX.VAr.phsC.cVal.mag.f MMXU3.MX.PPV.phsCA.cVal.mag.f MMXU1.MX.VA.phsA.cVal.mag.f MMXU3.MX.PPV.phsCA.cVal.ang.f MMXU1.MX.VA.phsB.cVal.mag.f MMXU3.MX.PhV.phsA.cVal.mag.f MMXU1.MX.VA.phsC.cVal.mag.f MMXU3.MX.PhV.phsA.cVal.ang.f MMXU1.MX.PF.phsA.cVal.mag.f MMXU3.MX.PhV.phsB.cVal.mag.f MMXU1.MX.PF.phsB.cVal.mag.f MMXU3.MX.PhV.phsB.cVal.ang.f MMXU1.MX.PF.phsC.cVal.mag.f MMXU3.MX.PhV.phsC.cVal.mag.f MMXU2.MX.TotW.mag.f MMXU3.MX.PhV.phsC.cVal.ang.f MMXU2.MX.TotVAr.mag.f MMXU3.MX.A.phsA.cVal.mag.f MMXU2.MX.TotVA.mag.f MMXU3.MX.A.phsA.cVal.ang.f MMXU2.MX.TotPF.mag.f MMXU3.MX.A.phsB.cVal.mag.f MMXU2.MX.Hz.mag.f MMXU3.MX.A.phsB.cVal.ang.f MMXU2.MX.PPV.phsAB.cVal.mag.f MMXU3.MX.A.phsC.cVal.mag.f MMXU2.MX.PPV.phsAB.cVal.ang.f MMXU3.MX.A.phsC.cVal.ang.f GE Multilin F35 Multiple Feeder Protection System B-91...
Page 514 MMXU4.MX.A.neut.cVal.mag.f MMXU6.MX.TotVA.mag.f MMXU4.MX.A.neut.cVal.ang.f MMXU6.MX.TotPF.mag.f MMXU4.MX.W.phsA.cVal.mag.f MMXU6.MX.Hz.mag.f MMXU4.MX.W.phsB.cVal.mag.f MMXU6.MX.PPV.phsAB.cVal.mag.f MMXU4.MX.W.phsC.cVal.mag.f MMXU6.MX.PPV.phsAB.cVal.ang.f MMXU4.MX.VAr.phsA.cVal.mag.f MMXU6.MX.PPV.phsBC.cVal.mag.f MMXU4.MX.VAr.phsB.cVal.mag.f MMXU6.MX.PPV.phsBC.cVal.ang.f MMXU4.MX.VAr.phsC.cVal.mag.f MMXU6.MX.PPV.phsCA.cVal.mag.f MMXU4.MX.VA.phsA.cVal.mag.f MMXU6.MX.PPV.phsCA.cVal.ang.f MMXU4.MX.VA.phsB.cVal.mag.f MMXU6.MX.PhV.phsA.cVal.mag.f MMXU4.MX.VA.phsC.cVal.mag.f MMXU6.MX.PhV.phsA.cVal.ang.f MMXU4.MX.PF.phsA.cVal.mag.f MMXU6.MX.PhV.phsB.cVal.mag.f MMXU4.MX.PF.phsB.cVal.mag.f MMXU6.MX.PhV.phsB.cVal.ang.f MMXU4.MX.PF.phsC.cVal.mag.f MMXU6.MX.PhV.phsC.cVal.mag.f MMXU5.MX.TotW.mag.f MMXU6.MX.PhV.phsC.cVal.ang.f MMXU5.MX.TotVAr.mag.f MMXU6.MX.A.phsA.cVal.mag.f B-92 F35 Multiple Feeder Protection System GE Multilin...
Page 515 GGIO4.MX.AnIn19.mag.f XSWI20.ST.Pos.stVal GGIO4.MX.AnIn20.mag.f XSWI21.ST.Loc.stVal GGIO4.MX.AnIn21.mag.f XSWI21.ST.Pos.stVal GGIO4.MX.AnIn22.mag.f XSWI22.ST.Loc.stVal GGIO4.MX.AnIn23.mag.f XSWI22.ST.Pos.stVal GGIO4.MX.AnIn24.mag.f XSWI23.ST.Loc.stVal GGIO4.MX.AnIn25.mag.f XSWI23.ST.Pos.stVal GGIO4.MX.AnIn26.mag.f XSWI24.ST.Loc.stVal GGIO4.MX.AnIn27.mag.f XSWI24.ST.Pos.stVal GGIO4.MX.AnIn28.mag.f XCBR1.ST.Loc.stVal GGIO4.MX.AnIn29.mag.f XCBR1.ST.Pos.stVal GGIO4.MX.AnIn30.mag.f XCBR2.ST.Loc.stVal GGIO4.MX.AnIn31.mag.f XCBR2.ST.Pos.stVal GGIO4.MX.AnIn32.mag.f XCBR3.ST.Loc.stVal XSWI1.ST.Loc.stVal XCBR3.ST.Pos.stVal XSWI1.ST.Pos.stVal XCBR4.ST.Loc.stVal GE Multilin F35 Multiple Feeder Protection System B-93...
Page 516 GGIO1.ST.Ind14.q GGIO1.ST.Ind40.stVal GGIO1.ST.Ind14.stVal GGIO1.ST.Ind41.q GGIO1.ST.Ind15.q GGIO1.ST.Ind41.stVal GGIO1.ST.Ind15.stVal GGIO1.ST.Ind42.q GGIO1.ST.Ind16.q GGIO1.ST.Ind42.stVal GGIO1.ST.Ind16.stVal GGIO1.ST.Ind43.q GGIO1.ST.Ind17.q GGIO1.ST.Ind43.stVal GGIO1.ST.Ind17.stVal GGIO1.ST.Ind44.q GGIO1.ST.Ind18.q GGIO1.ST.Ind44.stVal GGIO1.ST.Ind18.stVal GGIO1.ST.Ind45.q GGIO1.ST.Ind19.q GGIO1.ST.Ind45.stVal GGIO1.ST.Ind19.stVal GGIO1.ST.Ind46.q GGIO1.ST.Ind20.q GGIO1.ST.Ind46.stVal GGIO1.ST.Ind20.stVal GGIO1.ST.Ind47.q GGIO1.ST.Ind21.q GGIO1.ST.Ind47.stVal GGIO1.ST.Ind21.stVal GGIO1.ST.Ind48.q B-94 F35 Multiple Feeder Protection System GE Multilin...
Page 517 GGIO1.ST.Ind67.q GGIO1.ST.Ind93.stVal GGIO1.ST.Ind67.stVal GGIO1.ST.Ind94.q GGIO1.ST.Ind68.q GGIO1.ST.Ind94.stVal GGIO1.ST.Ind68.stVal GGIO1.ST.Ind95.q GGIO1.ST.Ind69.q GGIO1.ST.Ind95.stVal GGIO1.ST.Ind69.stVal GGIO1.ST.Ind96.q GGIO1.ST.Ind70.q GGIO1.ST.Ind96.stVal GGIO1.ST.Ind70.stVal GGIO1.ST.Ind97.q GGIO1.ST.Ind71.q GGIO1.ST.Ind97.stVal GGIO1.ST.Ind71.stVal GGIO1.ST.Ind98.q GGIO1.ST.Ind72.q GGIO1.ST.Ind98.stVal GGIO1.ST.Ind72.stVal GGIO1.ST.Ind99.q GGIO1.ST.Ind73.q GGIO1.ST.Ind99.stVal GGIO1.ST.Ind73.stVal GGIO1.ST.Ind100.q GGIO1.ST.Ind74.q GGIO1.ST.Ind100.stVal GGIO1.ST.Ind74.stVal GGIO1.ST.Ind101.q GE Multilin F35 Multiple Feeder Protection System B-95...
Page 518 GGIO1.ST.Ind120.q MMXU1.MX.PF.phsB.cVal.mag.f GGIO1.ST.Ind120.stVal MMXU1.MX.PF.phsC.cVal.mag.f GGIO1.ST.Ind121.q MMXU2.MX.TotW.mag.f GGIO1.ST.Ind121.stVal MMXU2.MX.TotVAr.mag.f GGIO1.ST.Ind122.q MMXU2.MX.TotVA.mag.f GGIO1.ST.Ind122.stVal MMXU2.MX.TotPF.mag.f GGIO1.ST.Ind123.q MMXU2.MX.Hz.mag.f GGIO1.ST.Ind123.stVal MMXU2.MX.PPV.phsAB.cVal.mag.f GGIO1.ST.Ind124.q MMXU2.MX.PPV.phsAB.cVal.ang.f GGIO1.ST.Ind124.stVal MMXU2.MX.PPV.phsBC.cVal.mag.f GGIO1.ST.Ind125.q MMXU2.MX.PPV.phsBC.cVal.ang.f GGIO1.ST.Ind125.stVal MMXU2.MX.PPV.phsCA.cVal.mag.f GGIO1.ST.Ind126.q MMXU2.MX.PPV.phsCA.cVal.ang.f GGIO1.ST.Ind126.stVal MMXU2.MX.PhV.phsA.cVal.mag.f GGIO1.ST.Ind127.q MMXU2.MX.PhV.phsA.cVal.ang.f GGIO1.ST.Ind127.stVal MMXU2.MX.PhV.phsB.cVal.mag.f B-96 F35 Multiple Feeder Protection System GE Multilin...
Page 519 MMXU3.MX.PhV.phsB.cVal.ang.f MMXU4.MX.VAr.phsC.cVal.mag.f MMXU3.MX.PhV.phsC.cVal.mag.f MMXU4.MX.VA.phsA.cVal.mag.f MMXU3.MX.PhV.phsC.cVal.ang.f MMXU4.MX.VA.phsB.cVal.mag.f MMXU3.MX.A.phsA.cVal.mag.f MMXU4.MX.VA.phsC.cVal.mag.f MMXU3.MX.A.phsA.cVal.ang.f MMXU4.MX.PF.phsA.cVal.mag.f MMXU3.MX.A.phsB.cVal.mag.f MMXU4.MX.PF.phsB.cVal.mag.f MMXU3.MX.A.phsB.cVal.ang.f MMXU4.MX.PF.phsC.cVal.mag.f MMXU3.MX.A.phsC.cVal.mag.f MMXU5.MX.TotW.mag.f MMXU3.MX.A.phsC.cVal.ang.f MMXU5.MX.TotVAr.mag.f MMXU3.MX.A.neut.cVal.mag.f MMXU5.MX.TotVA.mag.f MMXU3.MX.A.neut.cVal.ang.f MMXU5.MX.TotPF.mag.f MMXU3.MX.W.phsA.cVal.mag.f MMXU5.MX.Hz.mag.f MMXU3.MX.W.phsB.cVal.mag.f MMXU5.MX.PPV.phsAB.cVal.mag.f MMXU3.MX.W.phsC.cVal.mag.f MMXU5.MX.PPV.phsAB.cVal.ang.f MMXU3.MX.VAr.phsA.cVal.mag.f MMXU5.MX.PPV.phsBC.cVal.mag.f MMXU3.MX.VAr.phsB.cVal.mag.f MMXU5.MX.PPV.phsBC.cVal.ang.f GE Multilin F35 Multiple Feeder Protection System B-97...
Page 520 MMXU6.MX.PPV.phsCA.cVal.mag.f GGIO4.MX.AnIn26.mag.f MMXU6.MX.PPV.phsCA.cVal.ang.f GGIO4.MX.AnIn27.mag.f MMXU6.MX.PhV.phsA.cVal.mag.f GGIO4.MX.AnIn28.mag.f MMXU6.MX.PhV.phsA.cVal.ang.f GGIO4.MX.AnIn29.mag.f MMXU6.MX.PhV.phsB.cVal.mag.f GGIO4.MX.AnIn30.mag.f MMXU6.MX.PhV.phsB.cVal.ang.f GGIO4.MX.AnIn31.mag.f MMXU6.MX.PhV.phsC.cVal.mag.f GGIO4.MX.AnIn32.mag.f MMXU6.MX.PhV.phsC.cVal.ang.f GGIO5.ST.UIntIn1.q MMXU6.MX.A.phsA.cVal.mag.f GGIO5.ST.UIntIn1.stVal MMXU6.MX.A.phsA.cVal.ang.f GGIO5.ST.UIntIn2.q MMXU6.MX.A.phsB.cVal.mag.f GGIO5.ST.UIntIn2.stVal MMXU6.MX.A.phsB.cVal.ang.f GGIO5.ST.UIntIn3.q MMXU6.MX.A.phsC.cVal.mag.f GGIO5.ST.UIntIn3.stVal MMXU6.MX.A.phsC.cVal.ang.f GGIO5.ST.UIntIn4.q MMXU6.MX.A.neut.cVal.mag.f GGIO5.ST.UIntIn4.stVal MMXU6.MX.A.neut.cVal.ang.f GGIO5.ST.UIntIn5.q B-98 F35 Multiple Feeder Protection System GE Multilin...
Page 521 PDIS4.ST.Str.general PIOC20.ST.Op.general PDIS4.ST.Op.general PIOC21.ST.Str.general PDIS5.ST.Str.general PIOC21.ST.Op.general PDIS5.ST.Op.general PIOC22.ST.Str.general PDIS6.ST.Str.general PIOC22.ST.Op.general PDIS6.ST.Op.general PIOC23.ST.Str.general PDIS7.ST.Str.general PIOC23.ST.Op.general PDIS7.ST.Op.general PIOC24.ST.Str.general PDIS8.ST.Str.general PIOC24.ST.Op.general PDIS8.ST.Op.general PIOC25.ST.Str.general PDIS9.ST.Str.general PIOC25.ST.Op.general PDIS9.ST.Op.general PIOC26.ST.Str.general PDIS10.ST.Str.general PIOC26.ST.Op.general PDIS10.ST.Op.general PIOC27.ST.Str.general PIOC1.ST.Str.general PIOC27.ST.Op.general PIOC1.ST.Op.general PIOC28.ST.Str.general GE Multilin F35 Multiple Feeder Protection System B-99...
Page 522 PIOC47.ST.Str.general PTOC1.ST.Op.general PIOC47.ST.Op.general PTOC2.ST.Str.general PIOC48.ST.Str.general PTOC2.ST.Op.general PIOC48.ST.Op.general PTOC3.ST.Str.general PIOC49.ST.Str.general PTOC3.ST.Op.general PIOC49.ST.Op.general PTOC4.ST.Str.general PIOC50.ST.Str.general PTOC4.ST.Op.general PIOC50.ST.Op.general PTOC5.ST.Str.general PIOC51.ST.Str.general PTOC5.ST.Op.general PIOC51.ST.Op.general PTOC6.ST.Str.general PIOC52.ST.Str.general PTOC6.ST.Op.general PIOC52.ST.Op.general PTOC7.ST.Str.general PIOC53.ST.Str.general PTOC7.ST.Op.general PIOC53.ST.Op.general PTOC8.ST.Str.general PIOC54.ST.Str.general PTOC8.ST.Op.general PIOC54.ST.Op.general PTOC9.ST.Str.general B-100 F35 Multiple Feeder Protection System GE Multilin...
Page 523 PTOV4.ST.Str.general RBRF1.ST.OpIn.general PTOV4.ST.Op.general RBRF2.ST.OpEx.general PTOV5.ST.Str.general RBRF2.ST.OpIn.general PTOV5.ST.Op.general RBRF3.ST.OpEx.general PTOV6.ST.Str.general RBRF3.ST.OpIn.general PTOV6.ST.Op.general RBRF4.ST.OpEx.general PTOV7.ST.Str.general RBRF4.ST.OpIn.general PTOV7.ST.Op.general RBRF5.ST.OpEx.general PTOV8.ST.Str.general RBRF5.ST.OpIn.general PTOV8.ST.Op.general RBRF6.ST.OpEx.general PTOV9.ST.Str.general RBRF6.ST.OpIn.general PTOV9.ST.Op.general RBRF7.ST.OpEx.general PTOV10.ST.Str.general RBRF7.ST.OpIn.general PTOV10.ST.Op.general RBRF8.ST.OpEx.general PTRC1.ST.Tr.general RBRF8.ST.OpIn.general PTRC1.ST.Op.general RBRF9.ST.OpEx.general GE Multilin F35 Multiple Feeder Protection System B-101...
Page 524 RPSB1.ST.Op.general CSWI20.ST.Pos.stVal RPSB1.ST.BlkZn.stVal CSWI21.ST.Loc.stVal RREC1.ST.Op.general CSWI21.ST.Pos.stVal RREC1.ST.AutoRecSt.stVal CSWI22.ST.Loc.stVal RREC2.ST.Op.general CSWI22.ST.Pos.stVal RREC2.ST.AutoRecSt.stVal CSWI23.ST.Loc.stVal RREC3.ST.Op.general CSWI23.ST.Pos.stVal RREC3.ST.AutoRecSt.stVal CSWI24.ST.Loc.stVal RREC4.ST.Op.general CSWI24.ST.Pos.stVal RREC4.ST.AutoRecSt.stVal CSWI25.ST.Loc.stVal RREC5.ST.Op.general CSWI25.ST.Pos.stVal RREC5.ST.AutoRecSt.stVal CSWI26.ST.Loc.stVal RREC6.ST.Op.general CSWI26.ST.Pos.stVal RREC6.ST.AutoRecSt.stVal CSWI27.ST.Loc.stVal CSWI1.ST.Loc.stVal CSWI27.ST.Pos.stVal CSWI1.ST.Pos.stVal CSWI28.ST.Loc.stVal B-102 F35 Multiple Feeder Protection System GE Multilin...
Page 525 XSWI16.ST.Pos.stVal ENUMERATION: RADIUS AUTHENTICATION METHOD XSWI17.ST.Loc.stVal 0 = EAP-TTLS XSWI17.ST.Pos.stVal XSWI18.ST.Loc.stVal XSWI18.ST.Pos.stVal F620 XSWI19.ST.Loc.stVal ENUMERATION: PASSWORD CHANGE ROLES XSWI19.ST.Pos.stVal Enumeration Role XSWI20.ST.Loc.stVal None XSWI20.ST.Pos.stVal Administrator XSWI21.ST.Loc.stVal Supervisor XSWI21.ST.Pos.stVal Engineer XSWI22.ST.Loc.stVal Operator XSWI22.ST.Pos.stVal GE Multilin F35 Multiple Feeder Protection System B-103...
Page 526 Network Port 1 PP/PTP/IRIG-B/SNTP Network Port 2 Network Port 3 F624 ENUMERATION: REAL-TIME CLOCK SYNCHRONIZING SOURCE ACTUALS Enumeration Item None Port 1 PTP Clock Port 2 PTP Clock Port 3 PTP Clock IRIG-B B-104 F35 Multiple Feeder Protection System GE Multilin...
Page 527: Iec 61850
System Specification Description (SSD) file. The entire substation con- figuration is stored in a Substation Configuration Description (SCD) file. The SCD file is the combination of the individ- ual ICD files and the SSD file. GE Multilin F35 Multiple Feeder Protection System...
Page 528: File Transfer By Iec 61850
With the Copy option active, select a file to transfer and click the Go button. The file is copied and displays in the Local list on the left side of the window. Repeat the process to transfer any other files. Figure 0–1: FILE TRANSFER BY IEC 61850 F35 Multiple Feeder Protection System GE Multilin...
Page 529: Server Data Organization
GGIO4 (4 to 32) and the choice of the FlexAnalog values that determine the value of the GGIO4 analog inputs. Clients can utilize polling or the IEC 61850 unbuffered reporting feature available from GGIO4 in order to obtain the analog values provided by GGIO4. GE Multilin F35 Multiple Feeder Protection System...
Page 530: Mmxu: Analog Measured Values
The following list describes the protection elements for all UR-series relays. The F35 relay will contain a subset of protec- tion elements from this list. • PDIF: bus differential, transformer instantaneous differential, transformer percent differential, current differential F35 Multiple Feeder Protection System GE Multilin...
Page 531 IEC 61850 control model. • XCBR1.CO.BlkCls: This is where IEC 61850 clients can issue block close commands to the breaker. Direct control with normal security is the only supported IEC 61850 control model. GE Multilin F35 Multiple Feeder Protection System...
Page 532: Server Features And Configuration
F35. This attribute is programmed through the setting and its LOCATION default value is “Location”. This value should be changed to describe the actual physical location of the F35. F35 Multiple Feeder Protection System GE Multilin...
Page 533: Logical Node Name Prefixes
The exact structure and values of the supported IEC 61850 logical nodes can be seen by connecting to a F35 relay with an MMS browser, such as the “MMS Object Explorer and AXS4-MMS” DDE/OPC server from Sisco Inc. GE Multilin F35 Multiple Feeder Protection System...
Page 534: Generic Substation Event Services: Gsse And Goose
The configurable GOOSE feature allows for the configuration of the datasets to be transmitted or received from the F35. The F35 supports the configuration of eight (8) transmission and reception datasets, allowing for the optimization of data transfer between devices. F35 Multiple Feeder Protection System GE Multilin...
Page 535 “GGIO1.ST.Ind1.stVal” to indicate the status value for GGIO1 status indication 1. ITEM 2 The transmission dataset now contains a set of quality flags and a single point status Boolean value. The reception dataset on the receiving device must exactly match this structure. GE Multilin F35 Multiple Feeder Protection System...
Page 536 The value of remote input 1 (Boolean on or off) in the receiving device will be determined by the GGIO1.ST.Ind1.stVal value in the sending device. The above settings will be automatically populated by the EnerVista UR Setup software when a com- plete SCD file is created by third party substation configurator software. C-10 F35 Multiple Feeder Protection System GE Multilin...
Page 537: Ethernet Mac Address For Gsse/Goose
DatSet - the name of the associated dataset, and GoCBRef - the reference (name) of the associated GOOSE control block. These strings are automatically populated and interpreted by the F35; no settings are required. GE Multilin F35 Multiple Feeder Protection System...
Page 538: Iec 61850 Implementation Via Enervista Ur Setup
An ICD file is generated for the F35 by the EnerVista UR Setup software that describe the capabilities of the IED. The ICD file is then imported into a system configurator along with other ICD files for other IEDs (from GE or other ven- dors) for system configuration.
Page 539: Configuring Iec 61850 Settings
It can also import a system SCL file (SCD) to set communication configuration parame- ters (that is, required addresses, reception GOOSE datasets, IDs of incoming GOOSE datasets, etc.) for the IED. The IED configurator functionality is implemented in the GE Multilin EnerVista UR Setup software. C.5.2 CONFIGURING IEC 61850 SETTINGS Before creating an ICD file, the user can customize the IEC 61850 related settings for the IED.
Page 540: About Icd Files
Although configurable transmission GOOSE can also be created and altered by some third-party system con- figurators, we recommend configuring transmission GOOSE for GE Multilin IEDs before creating the ICD, and strictly within EnerVista UR Setup software or the front panel display (access through the Settings > Product Setup > Com- munications >...
Page 541 Furthermore, it defines the capabilities of an IED in terms of communication services offered and, together with its LNType, instantiated data (DO) and its default or configuration values. There should be only one IED section in an ICD since it only describes one IED. GE Multilin F35 Multiple Feeder Protection System C-15...
Page 542 Other ReportControl elements DOI (name) SDI (name) DAI (name) Text Other DOI elements SDI (name) DAI (name) Text Other LN elements Other LDevice elements 842797A1.CDR Figure C–4: ICD FILE STRUCTURE, IED NODE C-16 F35 Multiple Feeder Protection System GE Multilin...
Page 543 BDA (name, bType, type) Other BDA elements Other BDA elements Other DAType elements Other DAType elements EnumType (id) Text EnumVal (ord) Other EnumVal elements Other EnumType elements 842798A1.CDR Figure C–5: ICD FILE STRUCTURE, DATATYPETEMPLATES NODE GE Multilin F35 Multiple Feeder Protection System C-17...
Page 544: Creating An Icd File With Enervista Ur Setup
C.5.5 ABOUT SCD FILES System configuration is performed in the system configurator. While many vendors (including GE Multilin) are working their own system configuration tools, there are some system configurators available in the market (for example, Siemens DIGSI version 4.6 or above and ASE Visual SCL Beta 0.12).
Page 545 Like ICD files, the Header node identifies the SCD file and its version, and specifies options for the mapping of names to signals. The Substation node describes the substation parameters: Substation PowerSystemResource EquipmentContainer Power Transformer GeneralEquipment EquipmentContainer VoltageLevel Voltage PowerSystemResource Function SubFunction GeneralEquipment 842792A1.CDR Figure C–7: SCD FILE STRUCTURE, SUBSTATION NODE GE Multilin F35 Multiple Feeder Protection System C-19...
Page 546 IdInst is the instance identification of the logical device within the IED on which the control block is located, and cbName is the name of the control block. C-20 F35 Multiple Feeder Protection System GE Multilin...
Page 547: Importing An Scd File With Enervista Ur Setup
The following procedure describes how to update the F35 with the new configuration from an SCD file with the EnerVista UR Setup software. Right-click anywhere in the files panel and select the Import Contents From SCD File item. Select the saved SCD file and click Open. GE Multilin F35 Multiple Feeder Protection System C-21...
Page 548 The software will open the SCD file and then prompt the user to save a UR-series settings file. Select a location and name for the URS (UR-series relay settings) file. If there is more than one GE Multilin IED defined in the SCD file, the software prompt the user to save a UR-series set- tings file for each IED.
Page 549: Acsi Basic Conformance Statement
REPORTING Buffered report control M7-1 sequence-number M7-2 report-time-stamp M7-3 reason-for-inclusion M7-4 data-set-name M7-5 data-reference M7-6 buffer-overflow M7-7 entryID M7-8 BufTm M7-9 IntgPd M7-10 Unbuffered report control M8-1 sequence-number M8-2 report-time-stamp M8-3 reason-for-inclusion GE Multilin F35 Multiple Feeder Protection System C-23...
Page 550: Acsi Services Conformance Statement
UR FAMILY PUBLISHER SERVER (CLAUSE 7) ServerDirectory APPLICATION ASSOCIATION (CLAUSE 8) Associate Abort Release LOGICAL DEVICE (CLAUSE 9) LogicalDeviceDirectory LOGICAL NODE (CLAUSE 10) LogicalNodeDirectory GetAllDataValues DATA (CLAUSE 11) GetDataValues SetDataValues GetDataDirectory GetDataDefinition C-24 F35 Multiple Feeder Protection System GE Multilin...
Page 551 LOG CONTROL BLOCK GetLCBValues SetLCBValues QueryLogByTime QueryLogByEntry GetLogStatusValues GENERIC SUBSTATION EVENT MODEL (GSE) (CLAUSE 18, ANNEX C) GOOSE-CONTROL-BLOCK (CLAUSE 18) SendGOOSEMessage GetReference GetGOOSEElementNumber GetGoCBValues SetGoCBValues GSSE-CONTROL-BLOCK (ANNEX C) SendGSSEMessage GetReference GetGSSEElementNumber GetGsCBValues GE Multilin F35 Multiple Feeder Protection System C-25...
Page 552 (SendGOOSEMessage or SendGSSEMessage) NOTE c9: shall declare support if TP association is available c10: shall declare support for at least one (SendMSVMessage or SendUSVMessage) C-26 F35 Multiple Feeder Protection System GE Multilin...
Page 553: C.7.1 Logical Nodes Table
GGIO: Generic process I/O GLOG: Generic log GSAL: Generic security application I: LOGICAL NODES FOR INTERFACING AND ARCHIVING IARC: Archiving IHMI: Human machine interface ISAF: Safety alarm function ITCI: Telecontrol interface ITMI: Telemonitoring interface GE Multilin F35 Multiple Feeder Protection System C-27...
Page 554: Logical Nodes Table
PSCH: Protection scheme PSDE: Sensitive directional earth fault PTEF: Transient earth fault PTOC: Time overcurrent PTOF: Overfrequency PTOV: Overvoltage PTRC: Protection trip conditioning PTTR: Thermal overload PTUC: Undercurrent PTUF: Underfrequency PTUV: Undervoltage C-28 F35 Multiple Feeder Protection System GE Multilin...
Page 555 T: LOGICAL NODES FOR INSTRUMENT TRANSFORMERS TANG: Angle TAXD: Axial displacement TCTR: Current transformer TDST: Distance TFLW: Liquid flow TFRQ: Frequency TGSN: Generic sensor THUM: Humidity TLVL: Media level TMGF: Magnetic field TMVM: Movement sensor GE Multilin F35 Multiple Feeder Protection System C-29...
Page 556 ZLIN: Power overhead line ZMOT: Motor ZREA: Reactor ZRES: Resistor ZRRC: Rotating reactive component ZSAR: Surge arrestor ZSCR: Semi-conductor controlled rectifier ZSMC: Synchronous machine ZTCF: Thyristor controlled frequency converter ZTRC: Thyristor controlled reactive component C-30 F35 Multiple Feeder Protection System GE Multilin...
Page 557: Iec 60870-5-104 Protocol
Balanced Transmission Not Present (Balanced Transmission Only)   Unbalanced Transmission One Octet  Two Octets  Structured  Unstructured Frame Length (maximum length, number of octets): Not selectable in companion IEC 60870-5-104 standard GE Multilin F35 Multiple Feeder Protection System...
Page 558  <18> := Packed start events of protection equipment with time tag M_EP_TB_1  <19> := Packed output circuit information of protection equipment with time tag M_EP_TC_1  <20> := Packed single-point information with status change detection M_SP_NA_1 F35 Multiple Feeder Protection System GE Multilin...
Page 559  <103> := Clock synchronization command (see Clause 7.6 in standard) C_CS_NA_1  <104> := Test command C_TS_NA_1  <105> := Reset process command C_RP_NA_1  <106> := Delay acquisition command C_CD_NA_1  <107> := Test command with time tag CP56Time2a C_TS_TA_1 GE Multilin F35 Multiple Feeder Protection System...
Page 560 •Blank boxes indicate functions or ASDU not used. •‘X’ if only used in the standard direction TYPE IDENTIFICATION CAUSE OF TRANSMISSION MNEMONIC <1> M_SP_NA_1 <2> M_SP_TA_1 <3> M_DP_NA_1 <4> M_DP_TA_1 <5> M_ST_NA_1 <6> M_ST_TA_1 <7> M_BO_NA_1 <8> M_BO_TA_1 <9> M_ME_NA_1 F35 Multiple Feeder Protection System GE Multilin...
Page 561 M_ME_TD_1 <35> M_ME_TE_1 <36> M_ME_TF_1 <37> M_IT_TB_1 <38> M_EP_TD_1 <39> M_EP_TE_1 <40> M_EP_TF_1 <45> C_SC_NA_1 <46> C_DC_NA_1 <47> C_RC_NA_1 <48> C_SE_NA_1 <49> C_SE_NB_1 <50> C_SE_NC_1 <51> C_BO_NA_1 <58> C_SC_TA_1 <59> C_DC_TA_1 <60> C_RC_TA_1 GE Multilin F35 Multiple Feeder Protection System...
Page 562 F_FR_NA_1 <121> F_SR_NA_1 <122> F_SC_NA_1 <123> F_LS_NA_1 <124> F_AF_NA_1 <125> F_SG_NA_1 <126> F_DR_TA_1*) BASIC APPLICATION FUNCTIONS Station Initialization:  Remote initialization Cyclic Data Transmission:  Cyclic data transmission Read Procedure:  Read procedure F35 Multiple Feeder Protection System GE Multilin...
Page 563  Mode B: Local freeze with counter interrogation  Mode C: Freeze and transmit by counter-interrogation commands  Mode D: Freeze by counter-interrogation command, frozen values reported simultaneously  Counter read  Counter freeze without reset GE Multilin F35 Multiple Feeder Protection System...
Page 564 Maximum number of outstanding I-format APDUs k and latest acknowledge APDUs (w): PARAMETER DEFAULT REMARKS SELECTED VALUE VALUE 12 APDUs Maximum difference receive sequence number to send state variable 12 APDUs 8 APDUs 8 APDUs Latest acknowledge after receiving I-format APDUs F35 Multiple Feeder Protection System GE Multilin...
Page 565: Points List
The IEC 60870-5-104 data points are configured through the    SETTINGS PRODUCT SETUP COMMUNICATIONS DNP / menu. Refer to the Communications section of Chapter 5 for additional details. IEC104 POINT LISTS GE Multilin F35 Multiple Feeder Protection System...
Page 566 D.1 IEC 60870-5-104 PROTOCOL APPENDIX D D-10 F35 Multiple Feeder Protection System GE Multilin...
Page 567: Device Profile Document
Maximum Data Link Re-tries: Maximum Application Layer Re-tries:  None  None  Fixed at 3  Configurable  Configurable Requires Data Link Layer Confirmation:  Never  Always  Sometimes  Configurable GE Multilin F35 Multiple Feeder Protection System...
Page 568 FlexLogic. The On/Off times and Count value are ignored. “Pulse Off” and “Latch Off” operations put the appropriate Virtual Input into the “Off” state. “Trip” and “Close” operations both put the appropriate Virtual Input into the “On” state. F35 Multiple Feeder Protection System GE Multilin...
Page 569  16 Bits (Counter 8) Default Variation: 1  32 Bits (Counters 0 to 7, 9)  Point-by-point list attached  Other Value: _____  Point-by-point list attached Sends Multi-Fragment Responses:  Yes  No GE Multilin F35 Multiple Feeder Protection System...
Page 570: E.1.2 Implementation Table
Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the F35 is not restarted, but the DNP process is restarted. F35 Multiple Feeder Protection System GE Multilin...
Page 571 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the F35 is not restarted, but the DNP process is restarted. GE Multilin F35 Multiple Feeder Protection System...
Page 572 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the F35 is not restarted, but the DNP process is restarted. F35 Multiple Feeder Protection System GE Multilin...
Page 573 Otherwise, static object requests sent with qualifiers 00, 01, 06, 07, or 08, will be responded with qualifiers 00 or 01 (for change- event objects, qualifiers 17 or 28 are always responded.) Note 3: Cold restarts are implemented the same as warm restarts – the F35 is not restarted, but the DNP process is restarted. GE Multilin F35 Multiple Feeder Protection System...
Page 574: Dnp Point Lists
Change Event Variation reported when variation 0 requested: 2 (Binary Input Change with Time), Configurable Change Event Scan Rate: 8 times per power system cycle Change Event Buffer Size: 500 Default Class for All Points: 1 F35 Multiple Feeder Protection System GE Multilin...
Page 575: Binary And Control Relay Output
Virtual Input 59 Virtual Input 28 Virtual Input 60 Virtual Input 29 Virtual Input 61 Virtual Input 30 Virtual Input 62 Virtual Input 31 Virtual Input 63 Virtual Input 32 Virtual Input 64 GE Multilin F35 Multiple Feeder Protection System...
Page 576: Counters
A counter freeze command has no meaning for counters 8 and 9. F35 Digital Counter values are represented as 32-bit inte- gers. The DNP 3.0 protocol defines counters to be unsigned integers. Care should be taken when interpreting negative counter values. E-10 F35 Multiple Feeder Protection System GE Multilin...
Page 577: Analog Inputs
Change Event Variation reported when variation 0 requested: 1 (Analog Change Event without Time) Change Event Scan Rate: defaults to 500 ms Change Event Buffer Size: 256 Default Class for all Points: 2 GE Multilin F35 Multiple Feeder Protection System E-11...
Page 578 E.2 DNP POINT LISTS APPENDIX E E-12 F35 Multiple Feeder Protection System GE Multilin...
Page 579: Revision History
12 March 2008 URX-260 1601-0106-T1 5.6x 27 June 2008 08-0390 1601-0106-U1 5.7x 29 May 2009 09-0938 1601-0106-U2 5.7x 30 September 2009 09-1165 1601-0106-V1 5.8x 29 May 2010 09-1457 1601-0106-V2 5.8x 04 January 2011 11-2237 GE Multilin F35 Multiple Feeder Protection System...
Page 580: Changes To The Manual
Table F–3: MAJOR UPDATES FOR F35 MANUAL REVISION Y2 PAGE PAGE CHANGE DESCRIPTION (Y1) (Y2) Update Minor changes throughout document Delete Deleted CPU options U and V Update Updated Figure 1-1 Rear Nameplate Update Updated Figure 3-10 Rear Terminal View F35 Multiple Feeder Protection System GE Multilin...
Page 581 Added Flexanalog item PTP–IRIG-B Delta to Table A-1: Flexanalog Data Items Update Updated Modbus memory map table to include port 0 for Modbus slave address, TCP, DNP, HTTP, TFTP, MMS, and removed references to COM 1 RS485 port GE Multilin F35 Multiple Feeder Protection System...
Page 582 Table F–4: MAJOR UPDATES FOR F35 MANUAL REVISION Y1 (Sheet 2 of 2) PAGE PAGE CHANGE DESCRIPTION (X2) (Y1) C-23 C-23 Update Updated tables in sections C.6.3 ACSI Services Conformance Statement and C.7.1 Logical Nodes Table F35 Multiple Feeder Protection System GE Multilin...
Page 583: Abbreviations
FxE ....FlexElement™ ANG ....Angle FWD....Forward ANSI....American National Standards Institute AR ....Automatic Reclosure G .....Generator ASDU ..... Application-layer Service Data Unit GE....General Electric ASYM ..... Asymmetry GND....Ground AUTO ..... Automatic GNTR....Generator AUX....Auxiliary GOOSE...General Object Oriented Substation Event AVG....
Page 584 WRT....With Respect To RST ....Reset RSTR ..... Restrained X ....Reactance RTD ....Resistance Temperature Detector XDUCER..Transducer RTU ....Remote Terminal Unit XFMR..... Transformer RX (Rx) ..Receive, Receiver Z..... Impedance, Zone F35 Multiple Feeder Protection System GE Multilin...
Page 585: F.3.1 Ge Multilin Warranty
F.3.1 GE MULTILIN WARRANTY For products shipped as of 1 October 2013, GE Digital Energy warrants most of its GE manufactured products for 10 years. For warranty details including any limitations and disclaimers, see the GE Digital Energy Terms and Conditions at https://www.gedigitalenergy.com/multilin/warranty.htm...
Page 586: Warranty
F.3 WARRANTY APPENDIX F F35 Multiple Feeder Protection System GE Multilin...
Page 588 CONTACT OUTPUTS Modbus registers ............B-16 DIMENSIONS ............. 3-1, 3-2 CURRENT HARMONICS ..........6-21 DIRECT DEVICES CURRENT METERING actual values ..............6-10 actual values ..............6-16 Modbus registers ............B-21 specifications ..............2-12 settings ................ 5-199 F35 Multiple Feeder Protection System GE Multilin...
Page 590 FLEX STATE PARAMETERS actual values ..............6-8 G.703 ............ 3-31, 3-32, 3-33, 3-36 Modbus registers ..........B-17, B-43 G.703 WIRE SIZE .............3-31 settings ................. 5-71 GE TYPE IAC CURVES ..........5-127 specifications..............2-11 GROUND CURRENT METERING ........6-17 FLEXANALOG ..............A-1 GROUND IOC FLEXCURVES FlexLogic™...
Page 592 IAC ................5-127 PRODUCTION TESTS ............2-18 IEC ................5-126 PROTECTION ELEMENTS ..........5-4 IEEE ................5-125 PU QUANTITY ..............5-4 OVERVOLTAGE PUSHBUTTONS, USER-PROGRAMMABLE auxiliary ............. 2-10, 5-148 see USER-PROGRAMMABLE PUSHBUTTONS neutral ..............2-10, 5-146 F35 Multiple Feeder Protection System GE Multilin...
Page 593 SOFTWARE, PC RTD INPUTS see entry for EnerVista UR Setup actual values ..............6-24 SOURCE FREQUENCY ............ 6-21 Modbus registers ..........B-20, B-33 SOURCE TRANSFER SCHEMES ........5-143 settings ............... 5-207 specifications ..............2-14 GE Multilin F35 Multiple Feeder Protection System...
Page 594 FlexLogic operands ............5-111 ground ................. 5-138 Modbus registers ..........B-32, B-41 neutral ................. 5-132 settings ................5-65 phase ................5-129 specifications ..............2-11 specifications ..............2-9 USER-PROGRAMMABLE SELF TESTS Modbus registers ............B-30 settings ................5-63 viii F35 Multiple Feeder Protection System GE Multilin...
Page 596 INDEX F35 Multiple Feeder Protection System GE Multilin...

GE UR F35 Series Instruction Manual

1 Getting Started

2 Product Description

3 Hardware

4 Human Interfaces

5 Settings

6 Actual Values

7 Commands and

8 Security

9 Theory of Operation

10 Commissioning

11 Maintenance

Parameter Lists

Modbus Rtu Protocol

Modbus Function Codes

File Transfers

Memory Mapping

Iec 61850

Overview

Server Data Organization

Server Features and Configuration

Quick Links

Related Manuals for GE UR F35 Series

Summary of Contents for GE UR F35 Series