Interface Box Connections Installing the Ceiling (IP54 Housing) Gasket Attach Housing to the Interface Box Secure Housing to Ceiling Preparing the Bubble Connection 11.1 Connecting the AUTODOME camera to the PC Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 5
Licenses 14.54 Diagnostics 14.55 System Overview Operation 15.1 Using the AUTODOME Camera 15.2 Using Intelligent Tracking 15.3 Recommended Use of Your Camera Troubleshooting Maintenance Technical data User Command Table Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Legal Information Copyright This manual is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.
Page 7
(rain, snow, etc.); liquid has been spilled in or on the equipment; Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
16. Attachments, changes or modifications - Only use attachments/accessories specified by the manufacturer. Any change or modification of the equipment, not expressly approved by Bosch, could void the warranty or, in the case of an authorization agreement, authority to operate the equipment.
Page 9
Please dispose of these units at an environmentally compatible recycling facility, per European Directive 2002/96/EC. Environmental statement - Bosch has a strong commitment towards the environment. This unit has been designed to respect the environment as much as possible.
Page 10
Because the ISDN circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the Telephone Network Voltage (TNV) circuits. Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information.
High Power-over-Ethernet (High PoE): This unit can by powered via High PoE. To power the unit this way, use only approved High PoE devices – those offered or recommended by Bosch. High PoE can be connected at the same time as a 24 VAC power supply. If auxiliary power...
Page 12
Asia Pacific Region Please contact your local distributor or Bosch sales office. Use this link: http://www.boschsecurity.com/startpage/html/asia_pacific.htm More Information For more information please contact the nearest Bosch Security Systems location or visit www.boschsecurity.com 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. Refer to Customer Support and Service, for contact information.
Power Supply Box and cover with 120 VAC transformer VG4-A-PSU1 or with 230 VAC transformer VG4-A-PSU2 Trim Skirt for Power Supply Box (optional) VG4-A-TSKIRT Bosch High PoE 60W midspan NPD-6001A Corner Mount Kit – Corner Mount Plate VG4-A-9542 Mast (Pole) Mount Kit –...
Page 15
– Roof parapet Mount straight blade – Pipe Mount Screwdriver, No. 1 – Roof parapet Mount Phillips – Pipe Mount Pipe wrench – Roof parapet Mount – Pipe Mount Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
In-ceiling Mount cutting a hole in drywall or ceiling tile Pliers In-ceiling Mount Additional Products Required The following table lists additional products, sold separately by Bosch or other manufacturers, necessary to install AUTODOME cameras. Quantity Product Part Number Size SD card...
(not supplied). Warning! To minimize the potential for corrosion on the housing, use only Bosch hardware and mounts. See number 5 (Installation in a corrosive environment) in the section Recommended Use of Your Camera, page 141 for more information.
Cameras attached to a pole, roof, or to a bridge are especially vulnerable. Bosch offers the following recommendations to stabilize an AUTODOME 7000 and to decrease the affects of vibration on transmitted images, privacy masks, and Intelligent Tracking.
(such as wearing grounded wrist straps) to avoid electrostatic discharge. Warning! Bosch recommends disconnecting power to the camera while adding or removing an SD card. Follow the steps in one of these sections (depending on the type of camera mount): Remove the bubble from an in-ceiling housing, page 68 or Remove the bubble from a pendant housing, page 68.
Page 22
Follow the steps in one of these sections (depending on the type of camera mount): Replace the bubble in an in-ceiling housing, page 70 or Replace the bubble in a pendant housing, page 70. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
100–380 mm (4–15 in.). You must use a banding tool (sold separately) for a mast or pole installation. Follow the instructions provided with the banding tool to securely mount the Mast Plate to the pole. Contact your Bosch Sales Representative to order Banding Tool P/N TC9311PM3T.
Page 24
For units intended to be installed outdoors: All wiring (power and I/O cabling) connecting to the unit must be routed separately inside different permanently earthed metal conduits (not supplied). 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
COMMUNICATIONS to P106 in the Power Supply Box. Refer to connector P106 in the Power Supply Box Connections section below. Attach an RJ45 plug to the incoming Ethernet cable. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 26
Supply Box, page 33 for additional information. Power Supply Box Connections The following figure is a detailed illustration of the Pendant Arm Power Supply Box, which includes the fuse specifications. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 27
Series cameras: If you are mounting an AUTODOME 7000 Series camera to an ARM mount that was wired for an earlier model of Bosch AUTODOME, you must either re-wire cable 8 to be audio input and output, or disconnected it from the power supply.
Page 28
Pins for P106 1, 2, 4, and 5 are used for audio input and output for AUTODOME 7000 Series cameras; however, their labels are still those of previous versions of analog AUTODOME cameras. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
6 5 4 3 2 1 Figure 8.3: VG4-PSU1/VG4-PSU2 120/230 VAC Power In Transformer Ground Wire In/Out Conduit (1/2 in. [15 mm] NPS Fitting P101 Connector 24 VAC Power Out to VG4-PA0 P107 Connector Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 30
Connect the third wire to pin 3 (Earth Ground) connector. Refer to connector P107 in the table above and to the image below for an illustration of these connections: Figure 8.5: Outgoing 24 VAC power supply 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 31
P101 Connector Control Data and Video In/Out Wires (analog models only) 9. Follow the instructions in Attach Pendant Arm to Power Supply Box, page 32 to continue the installation. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Serious injury or death can occur if the hinge pins of the Pendant Arm are not fully engaged (locked) to the Power Supply Box. Exercise caution before releasing the Pendant Arm. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
After all wiring is complete, close the cover door and tighten the two (2) captive screws on the cover door to 10-12 N-m (90-105 in.-lbs) to ensure the Power Supply Box is watertight. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Follow the instructions provided with the banding tool to securely mount the Mast Plate to the pole. Contact your Bosch Sales Representative to order Banding Tool P/N TC9311PM3T.
Page 35
Pendant Arm and before proceeding to the next step. While continuing to hold the top hinge pin open, align the top and bottom hinges of the Pendant Arm to their mating points on the Mounting Plate. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 36
Mounting Plate. For a mast mount, route all wires through the right-angle conduit. Attach the water-tight plug to the other conduit. Attach the grounding spade terminal (item 1, below) to one of the spade terminals inside the Mounting Plate. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 37
(cable 7). 13. Connect the incoming serial communication wires to the 6-pin mating connector supplied with the VGA-PEND-WPLATE kit. Refer to the Power Supply Box Connections table above for details. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Tilt the bottom of the dome toward the pendant arm base and place the mounting hook, located on top of the dome housing, over the recessed hinge pin of the arm. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 39
Caution! If you feel any resistance when rotating the dome housing or when engaging the connector, stop immediately and start over. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 40
10-12 N-m (90-105 in.-lbs). Caution! You must tighten the two mounting screws to a minimum torque of 10-12 N-m (90‑105 in.-lbs) to ensure a proper seal between the arm and the housing. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
The VGA-ROOF-MOUNT is a stationary mount intended for rooftop parapet vertical walls. It is made of light weight aluminum with a corrosion-resistant finish and is used for all Bosch AUTODOME cameras up to a rated load of 29 kg (64 lb). This mount can be fitted to the inside or outside of parapet walls and can swivel for ease of positioning and for servicing the camera.
Page 42
Method Two is to bypass the Power Supply Box and route the video, control, and alarm wires directly to the Interface Board. You connect only the power wires inside the Power Supply Box. All conduit and junction boxes used must be electrically earth-grounded. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 43
The Power Supply Box with transformer comes with a barrier that separates the high voltage side on the left from the low voltage 24 VAC side on the right. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 44
Route the control wires from the Power Supply to the Pipe Interface Board. Then attach the supplied six (6) pin control data connector to the wires in the Power Supply Box. Refer to Wire the Pipe Interface Board, page 52. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 45
3 Fiber Optic cable (user-supplied) Power Supply Box Connections The following figure is a detailed illustration of the Roof or Pipe Mount Power Supply Box, which includes the fuse specifications. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 46
115 V T 1.6 A T 2.0 A T 3.15 A 230 V T 0.8A T 2.0 A T 3.15 A The following table lists the Power Supply Box connectors: 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Cover Door before proceeding to the next step. While holding the top hinge pin open, position the Cover Door to the Power Supply Box and align its hinges. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Apply sealant around each fastener hole Parapet Wall Bracket Roof Mount Plate 3/8-16 SS Hex Head Bolt Use a minimum of six (6) fasteners (not (supplied) supplied). Eight (8) fastener holes shown. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 49
10. Thread the Dome Cap onto the down pipe and tighten securely. See the illustration below. Warning! You must thread the Dome Cap onto the Down Pipe until it is tight. Failure to do so can result in damage, serious injury, or death. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Customer must supply 1-1/2 inch (NPS) pipe threaded on both ends with a minimum length of 5 inches (12.7 cm). You must use Teflon tape for thread-sealing compound. All screws shall be tightened securely. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 51
Thread the Pipe Cap onto the down pipe and tighten securely to prevent leaks. Warning! You must thread the Dome Cap onto the pipe until it is tight. Failure to do so can result in damage or serious injury or death. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
This section provides instructions for connecting wires and cables to the Pipe Interface Board, as illustrated below. Refer to the Connection, page 71 chapter for cable and wiring recommendations and specifications. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 53
Installing the Roof Parapet and Pipe Mounts | en AGND OUT 3 OUT 2 OUT 1 Figure 9.11: Pipe Interface Board Connections Pipe Interface Module Video Coax In J102 Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 54
Normally Open Dome Power P101 Dome 24 VAC 18-14 Earth Ground Dome 24 VAC Heater Power P107 Heater 24 VAC 18-14 Heater 24 VAC RJ45 Ethernet J101 To camera 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 55
Alarm Out 3 Alarm in 5 Alarm Out 4 Normally Closed Alarm Ground Alarm in 6 Earth Ground Alarm in 7 Analog Alarm 1 Alarm Ground Analog Alarm 2 Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Tilt the Pendant enough to place its mounting hook on top of the its housing, over the recessed hinge pin of the Dome Cap. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 57
Tighten the three (3) 10-mm (3/8-inch) stainless steel hex bolts on the bracket to lock the Parapet Arm in position. Caution! Do not over tighten the bolts. The maximum torque is 34 N-m (25 ft-lb). Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Connect the 24 VAC to Dome plug, installed previously, to its mating connector P107 on the right side of the box. Connect the 115/230 VAC, 3-pin Power-in plug, installed previously, to its mating connector P101 on the left side of the box. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Bar Clips Use the bracket Base Plate as a template or cut a holesize hole in the center of the ceiling tile with a drywall utility saw or jig saw. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 60
Tighten the four (4) securing screws to the Bracket Assembly. Figure 10.3: Tighten Bracket Securing Screw Secure the Bracket Assembly to an overhead securing point with a safety wire. Figure 10.4: Secure Bracket Assembly 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
To connect alarm inputs and outputs, attach the supplied 6-pin Alarms In and the 4-pin Alarms Out connector plugs with flying lead wires to the appropriate incoming alarm wires. Alarm Out 4 is a relay. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Secure the lid to the Interface box by pushing the lid down until the clip on the lid catches against the box. Interface Box Connections The following figure is a detailed illustration of the In-ceiling Interface box. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 63
(Audio IN-, (Audio IN+) (Ground) (Audio OUT+) (Audio CATIONS Audio in (Audio) OUT-; (Ground) signal Audio out ground) signal ground) J101 Ethernet Connector Input Table 10.1: Interface Box Wire Terminals Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
IP54 protection. (Refer to Replace the trim ring (optional) (In-ceiling models), page 69 for step-by-step installation instructions.) 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Carefully slide the gasket down over the housing, until it rests on the flange of the housing. Attach Housing to the Interface Box The In-Ceiling Housing is attached to the Interface Box and secured by two (2) thumbscrews. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 66
Tighten the two (2) Thumbscrews to secure the Interface Box to the housing. Figure 10.10: In-Ceiling Housing and Interface Box Interface Box Thumb Screw Ball Stud Tether Point In-ceiling Housing Ceiling Clamp 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Over-torquing the Ceiling Clamps can damage the clamp or ceiling. Only tighten the clamp until it contacts the ceiling and you start to feel some resistance. If using a power screwdriver, set the torque level to the lowest setting. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Notice! To avoid excessive moisture saturation inside the housing, limit the amount of time that the bubble is disconnected from the housing. Bosch recommends that the bubble be removed from the housing for no more than five (5) minutes. Remove the bubble from an in-ceiling housing Loosen the lockscrew (item 1 in the illustration below) in the trim ring using a P1 or smaller Phillips screwdriver until the bubble can rotate freely.
Page 69
Installing the Ceiling (IP54 Housing) Gasket, page 64 for an illustration of the correct placement of the gasket.) Place the black trim ring over the inner ring. Replace and tighten the four (4) screws. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 70
Replace the bubble in a pendant housing Insert the bubble and trim ring assembly into the pendant housing. Rotate the assembly clockwise until it locks. The latch mechanism makes a click when it locks. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
IP Connection Network Switch Computer Notice! You can also use the Bosch Video Client software application to configure the network settings for an AUTODOME 7000 Series camera. Go to www.boschsecurity.com to download the Configuration Manager software and Operating Manual. 11.2...
TCP/IP network using the built-in Web server. In addition, power can be supplied over the Ethernet cable using the Bosch High PoE 60W midspan (sold separately). Power can also be supplied over the Ethernet cable to in-ceiling models and indoor/outdoor pendant models used in indoor applications (where the heater is not powered) using PoE+ PSEs (midspan switches) compliant with the IEEE 802.3at, class 4 standard.
100 m (328 ft) Bandwidth 10 Base-T/100 Base-TX High PoE (required for pendants in outdoor applications that use Use the Bosch High PoE 60W midspan heaters) (sold separately). PoE+ (only for indoor models or indoor applications for pendant model IEEE 802.3at, class 4 standard...
Install a 2.2 K end-of-line resistor in the alarm circuit. Connect the alarm wires to input 1 or 2 (pin 5 or 6) and to the ground (pin 7) at the camera. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 75
From the Settings menu, select Advanced Mode > Interfaces > Alarm Inputs, select the Alarm Input # and N.C. See the table below for contact and condition details. AutoDome Programmed N.C.S. Contact Alarm Condition Open Alarm Closed Normal Short Tamper Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 76
From the Settings menu, select Advanced Mode > Interfaces > Alarm Inputs, select the Alarm Input # and N.C. See the table below for contact and condition details. AutoDome Programmed N.C. Circuit Alarm Indication Open Alarm Closed Normal 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Internal gain level adjustment is available in case the signal level is too low. Audio Line Output Specifications The following Line Output specifications should be complied with in all cases. Typical Output 1 Vrms Voltage Impedance 1.5 K Ω (typical) Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 78
Figure 12.6: Connections for audio over an Ethernet network Audio_In- (C-) AUTODOME Data In/Out Audio_In+ (C+) P105/P106 Connector Earth Ground Audio Out Audio_Out+ (RXD) Audio_Out– (TXD) Signal Ground 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 79
Separate the audio cables from the AC power lines to avoid noise. To configure audio on the camera, refer to Basic Mode: Audio, page 86 or Audio, page 106. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer. If you choose to use a computer running Microsoft Internet Explorer or any of the Bosch software, the computer must conform to the following minimum requirements: –...
Contact your local network administrator for a valid IP address, Subnet Mask, and a Gateway IP Address. Using the Configuration Manager Configuration Manager is an optional network utility provided on the Bosch Security Systems Web site. Use the Configuration Manager Manual to make any configuration changes. Notice! Depending on the PC network security settings, the user may need to add the new IP address to the browser’s trusted sites list for the controls to operate.
Page 82
Configure the settings on this page based on the addresses provided by your local network administrator. Note that the text on the Set button changes to Set and Reboot. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 83
Clicking the Set button saves the settings only in the current field. Changes in any other fields are ignored. Some changes only take effect after the unit is rebooted. In this case, the Set button changes to Set and Reboot. Make the desired changes. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Make sure that the display does not go beyond the green zone during modulation. For more information, refer to Audio, page 106. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
You can give the camera a name to make it easier to identify. The name makes the task of administering multiple units in larger video monitoring systems easier, for example using the Bosch Video Management Systems programs. The device name is used for the remote identification of a unit, in the event of an alarm for example.
If a DHCP server is employed in the network for the dynamic assignment of IP addresses, you can activate acceptance of IP addresses automatically assigned to the camera. Certain applications (VIDOS, Bosch Video Management Systems, Archive Player, Configuration Manager) use the IP address for the unique assignment of the unit. If you use these...
You can select all required text on this page with the mouse and copy it to the clipboard with the [Ctrl]+[C] key combination, for example if you want to send it via e-mail. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Note: It is important that the date/time is correct for recording. An incorrect date/time setting could prevent correct recording. Device time zone Select the time zone in which your system is located. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
If you select the Custom option, additional fields are displayed where you can specify the exact position (Position (XY)). In the Position (XY) fields, enter the values for the desired position. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 91
(live or saved) has been manipulated. If you want to add a digital signature to the transmitted video images to ensure their integrity, select one of the cryptographic algorithms for this signature. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Video player Select the desired video player from the list in the drop-down box. Options are “Auto detect” (default), Bosch Video SDK, Bosch Autoload Decoder, JPEG JPEG size You can specify the size of the JPEG image on the LIVE page. Options are Small, Medium, Large, 720p, 1080p, and “Best possible”...
Here you can specify whether the LIVE page displays the Special Functions section. Path for JPEG and video files Enter the path for the storage location of individual images and video sequences that you can save from the LIVE page. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
1280 x 720 and at 1920 x 1080. Orientation Reverses the image 180º (ideal when mounting upside down). Set the orientation to Normal (default) or Inverted. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 95
Click the Defaults button to restore the configuration settings defined in the camera’s web server to their default values. A confirmation screen appears. Allow 5 seconds for the camera to optimize the picture after a mode reset. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
The profiles are rather complex. They include a large number of parameters that interact with one another, so it is generally best to use the default profiles. Change the profiles only once you are fully familiar with all the configuration options. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 97
(IP frames only) or using as little bandwidth as possible. Options are IP, IBP, and IBBP. GOP is not available for megapixel cameras. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Note: In order to select the option “H.264 MP 720p50/60 Fixed” here, you must set the Max. frame rate field in the Advanced Mode: Camera >Installer Menu to “H.264 MP 720p50/60 Fixed” first. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 99
Picture quality: This setting allows you to adjust the image quality. Use the slide bar to choose a quality between Low and High. Note: The M-JPEG frame rate can vary depending on system loading. See also – Encoder Profile, page 96 Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Motion – Monitoring traffic or fast moving objects; motion artifacts are minimized – Vibrant – Enhanced contrast color reproduction and sharpness The default setting depends on whether the camera is an in-ceiling camera or a pendant camera. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 101
Select the speed of the response of auto exposure. Options are Super slow, Slow, Medium (default), Fast. Sharpness Adjusts the sharpness of the picture. To set the sharpness, use the slider to select a number. The default is 12. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 102
– Monochrome: Forces the camera to stay in Nigh Mode and transmit monochrome images. – Color: The camera does not switch to Night Mode regardless of ambient light conditions. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Normal (default): iris controls operate normally. – Reverse: iris controls are reversed. Auto iris level Increases or decreases brightness according to the amount of light. Type a value between 1 and 15. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Sets the left Auto Pan limit of the camera. Use the preview window to move the camera to the left pan limit and click the button. The camera will not move past this limit when in Auto Pan Between Limits mode (AUX 2 ON). 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
To delete a scene from the list, select the scene and click the Delete scene (“X”) button. To overwrite an existing scene: Click the View Control link to access the PTZ controls. Use the PTZ controls to navigate to the new scene. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
You can set the gain of the audio signals to suit your specific requirements. The current video image is shown in the small window next to the slide controls to help you check the audio source and improve assignments. Your changes are effective immediately. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
It is also possible to let the VRM Video Recording Manager control all recording with accessing an iSCSI system. This is an external program for configuring recording tasks for video servers. For further information please contact your local customer service at Bosch Security Systems Inc.
Page 108
Check the boxes for the Overwrite older recordings option to specify which older recordings can be overwritten once the available memory capacity has been used. Recording 1 corresponds to Stream 1, Recording 2 corresponds to Stream 2. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
If you select Off, no automatic recording takes place. Caution! You can specify limitations for overwriting older recordings in Continuous mode by configuring the retention time (see Maximum Retention Time, page 110). Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Maximum Retention Time Enter the required retention time in hours or days for each recording. Recording 1 corresponds to Stream 1, Recording 2 corresponds to Stream 2. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Recording status The graphic indicates the recording activity of the camera. You will see an animated graphic while recording is taking place. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
In this page, you can save a maximum of ten destination IP addresses and hence up to ten passwords for connecting to remote stations. If connections to more than ten remote stations are to be possible, for example when initiating connections via higher-ranking systems such as 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 113
AUTODOME 7000 Configuration via IP, Advanced Mode | en VIDOS or Bosch Video Management System, you can store a general password here. The camera can use this general password to connect to all remote stations protected with the same password. In this case, proceed as follows: Select 10 from the Number of destination IP address list field.
Page 114
This can be useful if you want to test a number of different configurations. Save a functioning configuration and test new settings. You can use the saved configuration to restore the original settings at any time. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 115
Notice! Additional analysis algorithms with comprehensive functions such as IVMD and IVA are available from Bosch Security Systems Inc. If you select one of these algorithms, you can set the corresponding parameters here directly. You can find information on this in the relevant documents on the product CD supplied.
Page 116
The options for tamper detection can only be set for fixed cameras. Dome cameras or other motorized cameras cannot be protected in this manner as the movement of the camera itself causes changes in the video image that are too great. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 117
Check the box Reference check to activate on-going matching. The stored reference image is displayed in black and white below the current video image, and the selected areas are marked in yellow. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
The camera can create alarms on the basis of audio signals. You can configure signal strengths and frequency ranges in such a way that false alarms, for example due to machine noise or background noise, are avoided. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Select On if you want the device to generate audio alarms. Name The name makes it easier to identify the alarm in extensive video monitoring systems, for example with the VIDOS and Bosch Video Management System programs. Enter a unique and clear name here. Caution! Do not use any special characters, for example &, in the name.
LIVE page. The physical input connection can be activated by dry contact devices such as pressure pads, door contacts, and similar devices. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Output name Type an optional name for the relay connection, up to 20 characters. Trigger output Click the appropriate Trigger output button to test the relay / output connection. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
If a DHCP server is employed in the network for the dynamic assignment of IP addresses, you can activate acceptance of IP addresses automatically assigned to the camera. Certain applications (Bosch Video Management System, Archive Player, Configuration Manager) use the IP address for the unique assignment of the unit. If you use these...
Page 123
To exchange connection data, you can activate the unsecured RCP+ port 1756. If you want connection data to be transmitted only when encrypted, select the Off option to deactivate the port. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
The status of the DynDNS function is displayed here for information purposes. You cannot change any of these settings. Notification mail Select On to set the system to provide email notification of domain registration. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
1. SNMP host address / 2. SNMP host address If you wish to send SNMP traps automatically, enter the IP addresses of one or two required target units here. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Example: the file snap011005_114530.jpg was stored on October 1, 2005 at 11:45 and 30 seconds. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
A special license, with which you will receive a corresponding activation key, is required to encrypt user data. You can enter the activation key to release the function on the Licenses page (see Licenses, page 130). 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
The page displays a progress bar as the firmware is uploaded. Note: Once the progress bar reaches 100%, the system opens the reset page. Allow the reset page to complete its action. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
You can select all required text on this page with the mouse and copy it to the clipboard with the [Ctrl]+[C] key combination, for example if you want to send it via e-mail. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
“discovery” symbol is shown. While discovery is executed, gaps might be shown in places which the discovery has not yet reached. The gap will automatically be replaced by the true video, as soon as the correct information is available. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 132
If you do not connect, the unit may have reached its maximum number of connections. Depending on the unit and network configuration, each camera can have up to 50 Web browser connections or up to 100 connections via the Bosch Video Management System (BVMS).
Page 133
The device’s configuration determines whether the alarm is displayed, as well as additional details (see the AUTODOME 7000 Series online help). Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 134
Set scene, AUX on, AUX off). A valid combination either issues a command to the camera or displays an on-screen menu. To access the AUX Control tab, go to the LIVE page and click the AUX Control tab. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 135
Click the Set scene button. The image area displays a message that indicates which shot number was saved. To View a Preset Shot: Click the number of the scene you want to view using the on-screen keypad. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 136
JPEG format on your computer's hard drive. The icon for recording single images is only visible if the unit is configured to enable this process. Click the icon. The storage location depends on the configuration of the camera. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 137
Click Recordings to access the Recordings page from the LIVE page or SETTINGS page (the Recordings link is only visible if a storage medium has been selected). Figure 16.2: Playback page Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 138
All bookmarks are deleted when leaving the page. Tracking For information about the Tracking section of the LIVE page, refer to Using Intelligent Tracking, page 139. See also – User Command Table, page 149 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Avoid neon lights, flashing lights, night time lights, and reflected light (from a window or mirror, for example). The flickering of these lights can affect the Intelligent Tracking operation. – Avoid motion from moving leaves/branches that present a persistent fixed motion. Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 140
Intelligent Tracking is idle, waiting to track a target. Gray eye with a “pause” Intelligent Tracking attempts to track a symbol target passively while a user has camera control. Tracking triggered by IVA rules 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
The tour should also include at least 10° of tilt movement. Preset Tours For scenarios that require the camera to be in continuous motion for most of the day, Bosch recommends that you set the camera in Preset Tour mode, moving between a desired set of presets.
Page 142
If you must remove the bubble (for example, to install or remove an SD card), do not leave the bubble off of the dome for longer than five minutes. Bosch also recommends that you keep the dome camera in its packaging until you are ready to install the camera.
Page 143
SD cards for recording. Bosch is not liable for any damage that results from missing video information. Bosch does not make any commitments or promises regarding quality, performance, or other features with respect to third party products (such as SD cards).
If camera’s IP address is not set, then: – Use Configuration Manager to confirm that two cameras do not have the same IP address. If they do, change the address of one of the cameras. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Page 145
- In the Base frame rate field, choose either 25 ips or 30 ips. – Check the integrity of all connectors and splices of the Ethernet cable. If O.K., then: – Contact Bosch Technical Support. Loss of Privacy when – Webbrowsers, BVC or BVMS using Privacy Mask –...
Notice! To avoid excessive moisture saturation inside the housing, limit the amount of time that the bubble is disconnected from the housing. Bosch recommends that the bubble be removed from the housing for no more than five (5) minutes. Bubble Handling The bubble may be packaged with a protective plastic sheet.
Page 147
Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com to order or to find a local distributor.
For product specifications, see the datasheets for AUTODOME IP 7000 Series and for AUTODOME HD 7000 Series, available on the appropriate product pages of the Online Product Catalog at www.boschsecurity.com. 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.
Turns Intelligent Tracking on or off On/Off Digital Zoom Lock Turns digital zoom on and off On/Off Sector Blanking On–enable Off–disable On/Off Privacy Masking On–enable Off–disable On/Off Command Lock/Unlock On–lock on Off–lock off Bosch Security Systems, Inc. Operation Manual 2014.04 | 2.0 | F.01U.283.679...
Page 150
Turbo mode On – activates turbo mode Off – deactivates turbo mode Set/Shot 901-999 Adds or removes Set ###–adds preset to tour presets from tour Shot ###–removes preset from tour 2014.04 | 2.0 | F.01U.283.679 Operation Manual Bosch Security Systems, Inc.