Related Manuals for Siemens SPCK 420
Summary of Contents for Siemens SPCK 420
- Page 1 SPCK 420/421 LCD-Keypad User Guide Version 3.1 Siemens AB A6V10209178 26.09.2011 Security Products...
- Page 2 Copyright Technical specifications and availability subject to change without notice. © Copyright Siemens AB We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights and undertakes not to...
-
Page 3: Table Of Contents
DOOR CONTROL ................28 6.2.12 GRANT ACCESS ................28 6.2.13 REPORT TO ENG ................29 6.2.14 ACCESS LOG ..................29 Appendix ......................30 User rights ......................30 User PINs ......................32 Zone chart ......................32 Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 4: Security
Danger of electrical shock during maintenance Maintenance work must only be carried out by trained specialists. Danger of electrical shock while cleaning the device Do not use liquid cleaners or sprays that contain alcohol, spirit or ammonia. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 5: Meaning Of Written Warning Notices
Possible danger of death or severe bodily harm. CAUTION Danger of minor bodily injury or property damage IMPORTANT Danger of malfunctions Meaning of hazard symbols WARNING Warning of hazard area WARNING Warning of dangerous electrical voltage Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 6: Directives And Standards
This product complies with the requirements of the European Directives 2004/108/EC “Directive of Electromagnetic Compatibility” and 2006/95/EC “Low Voltage Directive”. The EU declaration of conformity is available to the responsible agencies at: Siemens AB Building Technologies Division International Headquarters Fire Safety & Security Products Postal Address P.O. -
Page 7: Introduction
3 LEDs on the keypad provide an indication of AC power, system alerts, and communications status. The standard keypad may be factory fitted with a Portable ACE (PACE) proximity device reader (see page [➙ 10]). Siemens AB A6V10209178 Security Products 26.09.2011... - Page 8 Users can unhinge these clips from the front assembly by inserting a 5mm screwdriver into the recesses and pushing gently. Back assembly This screw secures the front and back assemblies on the keypad. This screw securing screw must be removed to open the keypad. Siemens AB A6V10209178 Security Products 26.09.2011...
- Page 9 X-BUS If the keypad is being installed for the first time and power is supplied to it before a connection to the controller X-BUS interface is made, the LED remains in the ON state Siemens AB A6V10209178 Security Products 26.09.2011...
-
Page 10: Overview Of Keypad Types
✓ Comfort Keypad with Audio/CR SPCK623 ✓ ✓ ✓ Keypad Label SPCK420/421 1 Label on inside of Keypad 2 Pull-down label for providing installer details. Fill in all relevant details when installation is complete. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 11: Using The Keypad Interface
In Alphanumeric mode, press this key over a lower case character to change the character to upper case. 7 LEFT SOFT This key is used to select the option presented on the left side of the bottom line display. Siemens AB A6V10209178 Security Products 26.09.2011... - Page 12 Modem 2 fault – Modem 2 line – Fail to communicate – User panic – XBUS cable fault – XBUS communications fault – XBUS mains fault – XBUS battery fault – XBUS power supply fault Siemens AB A6V10209178 Security Products 26.09.2011...
- Page 13 Area state – Low battery (sensor) – Sensor lost – WPA Low battery – WPA lost – WPA Test overdue – Camera offline – Reboot – Hardware fault – Aux over current – Battery low Siemens AB A6V10209178 Security Products 26.09.2011...
-
Page 14: User Programming Via The Keypad
For each menu option, the keypad must be in User programming: 1. Enter a valid User code. 2. To select a programming option, use the up/down arrow keys or enter the digit listed in the table below. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 15: Unset
The second line displays the exit time and the buzzer sounds to indicate that the user should exit the building. When the system has been fully set, the LCD displays SYSTEM FULLSET on the bottom line for approximately 10 seconds. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 16: Partset
(in accordance with standards). An alert condition can only be restored once the fault or zone that caused the alert has been physically reset to its normal operating state; e.g. an open zone has been Siemens AB A6V10209178 Security Products... -
Page 17: Coded Restore
Contact the installer before entering user programming and selecting the coded restore feature. The contact details of the installer should be available from the drop down label beneath the keypad. 1. Press SELECT on the Coded Restore option. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 18: User Menus
REPORT TO ENG Allows the user to request that the last 10 events in the log be sent to the engineer by SMS message. The 10 events may require more than one SMS message, depending on Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 19: System Status
Inhibiting a zone removes that zone from the system for one alarm set period only. To inhibit zones or alerts from X-BUS devices: 1. Scroll to INHIBIT and press SELECT. 2. Scroll to the desired option in the table below and press SELECT: Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 20: Set Date/Time
5. Press ENTER to save the new time. If an attempt is made to save an invalid time value, the text INVALID VALUE is displayed for 1 second and the user is prompted to enter a valid time. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 21: Test
The keypad display flashes ACTIVATE WPA. 3. Press and hold all 3 buttons on the WPA. The LED on the WPA turns on. The WPA transmitter ID, status and signal strength are displayed on the keypad. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 22: Event Log
The chime function can be enabled or disabled on all zones where the chime has been programmed as an audible alert feature. To enable or disable the chime function: 1. Scroll to CHIME and press SELECT. 2. Toggle between ENABLED and DISABLED for the chime. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 23: Users
1. Confirm the new PIN and press SAVE. 2. Press BACK to return to the previous screen to amend the PIN. During the process if the display times out, the old PIN remains valid. Siemens AB A6V10209178 Security Products... -
Page 24: Sms
The SMS notification can operate with a PSTN modem if the PSTN operator supports SMS over PSTN where as SMS control will need a GSM modem at the panel. A GSM modem will support both SMS notification and control. Siemens AB A6V10209178 Security Products... - Page 25 Adding a phone number To add a phone number for SMS use: 1. Scroll to SMS EVENTS and press SELECT. 2. Scroll to ADD NUMBER and press SELECT. The LCD displays SMS NUMBER. Siemens AB A6V10209178 Security Products 26.09.2011...
-
Page 26: Sms Commands
Where **** is the code and “command” is the command: ****.command or **** command. For example, the command “HELP” is this text: **** HELP or ****.HELP COMMANDS (**** = code) Siemens AB A6V10209178 Security Products 26.09.2011... - Page 27 (Example: O5 for mapping gate 5) For SMS recognition, X-10 device uses the format: XYNN, where X stands for X- 10; Y stands for the alphabetic identity and NN are the available numeric placeholders. (Example: XA1) Siemens AB A6V10209178 Security Products 26.09.2011...
-
Page 28: Door Control
1. Scroll to GRANT ACCESS and press SELECT. 2. Select to ALLOW ENGINEER and select ENABLED. 3. Select to ALLOW MANUFACT. and select ENABLED. 4. To disallow engineer/manufacturer access, follow the same path and toggle to DISABLED and press SELECT. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 29: Report To Eng
2. Select a door on the system for which you want to display access events. The most recent access events are displayed with a date and time. 3. Scroll down through the access events or enter a date and press ENTER to find a particular access event. Siemens AB A6V10209178 Security Products 26.09.2011... -
Page 30: Appendix
An alert condition can only be restored after the zone(s) or fault(s) that triggered the alert condition have been restored to their normal operating state and the Siemens AB A6V10209178 Security Products 26.09.2011... - Page 31 This menu option allows for enabling or disabling of the chime feature on all zones. Standard* This feature allows users to set up the SMS messaging Manager service if a modem is installed on the system. Siemens AB A6V10209178 Security Products 26.09.2011...
-
Page 32: User Pins
Number of variations 10,000 100,000 10,000,000 10,000,000 100,000,000 All User PINs are valid, hence for a 4 digit PIN the numbers can be from 0000 through to 9999 with any combination allowed in between. Zone chart Siemens AB A6V10209178 Security Products 26.09.2011... - Page 33 Appendix Zone chart Zone # Description Siemens AB A6V10209178 Security Products 26.09.2011...
- Page 34 Appendix Zone chart Zone # Description Siemens AB A6V10209178 Security Products 26.09.2011...
- Page 35 Issued by © 2011 Copyright Siemens AB Siemens AB Technical specifications and availability subject to change without notice. Industry Sector Security Products International Headquarters Englundavägen 7 SE-171 24 Solna Tel. +46 8 629 0300 www.siemens.com/securityproducts Document ID A6V10209178 Edition 26.09.2011...