GE JDP47 Installation Instructions Manual
Self-cleaning radiant electric drop-in range
Hide thumbs
Also See for JDP47:
- Owner's manual (37 pages) ,
- Installation instructions manual (16 pages) ,
- Installation instructions manual (17 pages)
Table of Contents
Quick Links
See also:
Owner's Manual
Installation
Instructions
Self-Cleaning
Radiant
Electric Drop-In Range
JDP47, JD968
If you have questions, call 1.800.GE.CARES or visit our website at:
www.GEAppliances.com
Before You Begin
Read these instructions carefully and completely.
• IMPORTANT-save
these
instructions
for local inspector's
use.
• IMPORTANT-observe a,
governing
codes and ordinances.
• Note to InstallermBe
sure to leave these
instructions
with the consumer.
• Note to Consumer--Keep
these
instructions
for future reference,
• Proper installation
is the responsibility
of the installer
and product
failure due
to improper
installation
is NOT covered
under the warranty.
• NOTEmThis
appliance
must be properly
grounded.
• ATTENTION INSTALLER
All electric drop-in ranges must be hard
wired (direct wired) into an approved
junction box. A plug and receptacle
is NOT
permitted on these products.
Parts Included
%%
2 Shoulder Screws
(for stop device)
2 Screws
Materials Needed
Junction Box
Strain Relief Clamp
for 1/2" conduit
Wire Nuts
Pub. No. 31-10529-1
229c4053P508-1
Tools You Will Need
1/8" Drill Bit and
Electric or Hand Drill
Level
Phillips Screwdriver
Standard Screwdriver
Nut Driver
Tape Measure
Straight Edge
or Square
Hand or Sabre Saw
Hammer
Pencil
Safety Glasses
Table of Contents
Related Manuals for GE JDP47
Summary of Contents for GE JDP47
- Page 1 Installation Self-Cleaning Radiant Electric Drop-In Range Instructions JDP47, JD968 If you have questions, call 1.800.GE.CARES or visit our website at: www.GEAppliances.com Before You Begin • Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered Read these instructions carefully and completely.
- Page 2 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical For Your Safety Requirements WARNING: For personal This appliance must be supplied with the safety, remove house fuse or proper voltage and frequency, and connected open circuit breaker before to an individual, properly grounded branch beginning installation.
-
Page 3: Pre-Lnstallation Checklist
To obtain Kits: emove packing materials. Remove a. Visit GE Web Site (See page 1) labels on door, plastic on trims and b. Call GE Answer Center (See page 1) panel, and all tape around the range. - Page 4 Installation Instructions Pre-lnstallation Cutout and Required Clearances Overall Depth 26 1/2" NOTE: Drop-In Ranges are designed to hang from the countertop only. Do not install on a platform or support rails. Protective Strips (If Supplied) Follow instructions packaged with alternate appliances, Front (24"...
-
Page 5: Standard Installation Preparation
Installation Instructions Standard Installation Preparation STANDARD INSTALLATION Wall -_ Flat Area t 1' 1/4" Min. Flat ,yp%,y 1/4,,_ I-- 23-3/16" 9/16" Min. 9116" Min. Flat ,1{.-- --Flat Range_upport ..I" <-_ 29-15/16"-30-1/16" Smooth Cut Countertop Braces secured between the underside of the countertop and the cabinet if required to obtain 1-1/4"... -
Page 6: Electrical Connections
Installation Instructions Electrical Connections emove house fuse or open circuit breaker. WARNING: Improper connection of aluminum house Loosen screws for the junction wiring to copper leads can cover and rotate out of place or remove result in an electrical hazard or fire. the cover. - Page 7 Installation Instructions Electrical Connections cont THREE-CONDUCTOR BRANCH NEW CONSTRUCTION CIRCUIT CONNECTION FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION When connecting to a 3-conductor branch circuit, if local codes permit: • When installing in new construction, • When installing oven in a mobile home or Connect the bare oven ground recreational vehicle, or...
- Page 8 Installation Instructions Electrical Connections cont Reinstall Junction box cover. Do not shorten the flexible conduit. The conduit strain relief clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp. If the flexible conduit will not fit within the junction box, do not install the oven...
- Page 9 Installation Instructions I51Standard Installation Instructions Installing the Anti-Tip Bracket Select the proper position for the countertop thickness and move bracket to proper position. The anti-tip bracket is attached (Unit is supplied with bracket in position 1 .) the back of the Drop-In Range. It is For 3/4"...
- Page 10 Installation Instructions 1-51 Standard Installation Instructions cont. Install Stop Screw Placing the Range into the Opening These screws prevent the range from sliding out of position during operation. It is suggested that two people lift the range into place, carefully setting the side metal flanges under the glass on...
- Page 11 Installation Instructions 1-51 Standard Installation Instructions cont. Remove the Protective Attach the Lower Trim Channels (if provided) Attach the lower trim (supplied separately with the range) to the Carefully remove the protective bottom of the vertical side trim with channels from the sides of the glass the 2 screws supplied.
- Page 12 Installation Instructions 151 Standard Installation Instructions cont Replacing the Oven Door I"_ Push the hinge locks up against the front frame of the oven cavity, to the locked position. NOTE: The oven door is heavy. You Hinge in may need help lifting the door high Locked Position enough to slide it into the hinge slots.
-
Page 13: Final Checklist
Installation Instructions Final Checklist Check to make sure the circuit breaker is closed (Reset) or the circuit fuses are replaced. Be sure power is in service to the building. Check to be sure that all packing materials and tape on metal panel (if applicable) under control knobs and drawer have been removed. -
Page 14: Alternate Construction
Installation Instructions Alternate Construction Preparation Island Installation Optional Maintop Filler or Backguard When installing in an island or other non-standard location, countertop cutout If counter opening extends to the wall, it dimensions must be according to page 5. will require Maintop Filler Kit (JXS66XX) or Backguard Kit (JXS36XX or JXS39SS) For the anti-tip bracket instructions, see to close the gap. - Page 15 NOTES...
- Page 16 NOTES Pub, No, 31-10529-1 12-04 JR 22904053P508-1...