Page 1
1/2" MODEL 3612B INSTRUCTION MANUAL DOUBLE INSULATION Main body load Overall Collet chuck weight capacity stroke speed length 6 5 m m 23,000 287 m m 112" (1 1-5/16") (12.7 Ibs) 2-9/16") R/min.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
Page 3
DISCONNECT TOOLS. When not use, before servicing, and when chang- ing accessories, such as blades, bits, cutters. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning with AVOID UNINTENTIONAL STARTING.
ADDITIONAL SAFETY RULES These bits come fully sharpened. Handle them carefully t o prevent injury. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation.
Page 5
Installing Loosen the collet nut and insert the bit into the chuck hole. Press the shaft lock and use the wrench to secure the bit care- fully. Use the collet sleeve if necessary. CAUTION : Do not tighten the collet chuck without inserting a bit; do not install a small bit with- out using collet sleeve.
Page 6
Stopper block .The stopper block has an adjustment hex bolts which move 1 mm (1/32") per turn. After obtaining the desired depth setting, tighten the hex nut on the bolt with the spanner. block Nylon nut By turning the nylon nut, the upper limit of the tool can be adjusted.
Operation *After switching on the tool, lower the router, keeping the base plate firmly against the work surface while routing. CAUTION When doing edge routing, the workpiece surface should be on the left side of the bit in the router feed direction or a dangerous kickback may result. Bit revolving direction Correct bit feed direction...
Page 8
Straight guide .The straight guide is effectively used for straight cuts when chamfering or groov- ing. When grooving, the router tends to pull away to the left in relation to the feed direction. Install the straight guide on the right side assure good finished cut.
Page 9
Trimmer guide .Trimming, inside work and curved cuts in veneers for furniture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures fine cut. *The trimmer guide can be attached to the guide holder with the thumb bolt Loosening the thumb bolt the distance...
BNSh holder holder cap as shown on the figure. .Take out the worn brush, insert the new one and secure the brush holder cap. Any other maintenance should be performed by an Authorized Makita Service Center or point of purchase.
Page 11
ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should used in the proper and intended manner.
Page 12
Bits STRAIGHT -Single Flute CARBIDE TIPPED P A R T N O . 1-1/2 2-3/4 733002-0A 733002-4A 1 /2 1-1 /4 1 -3/8 2-7/8 HIGH SPEED STEEL PART NO. 733232-6A 5/16 V l / 8 1 /4 1.518 STRAIGHT 2 Flute CARBIDE TIPPED PART NO.
Page 13
VEINING -Single Flute SOLID CARBIDE PART NO 3 / 1 6 7/32 1-1 14 1-1 12 733007-8A ROUND NOSE CARBIDE TIPPED PART NO 1-718 733008-2A 15/32 1-1 14 9116 1-114 733008-4A 1 12 11116 1-114 2-3116 7330086A 11116 1-114 2.114 733008-8A 13116 1-114...
Page 14
14" DOVE TAIL CARBIDE TIPPED PART NO. 1 I2 733009-6A 1-1/4 1-718 HIGH SPEED STEEL PART NO. 733239-6A 1-318 STAGGER TOOTH - I D ! - CARBIDE TIPPED PART NO. 733007-0A 1-112 1-1 I 4 PANEL PILOT CARBIDE TIPPED PART NO. 733030-4A 733030-6A 1 118...
Page 18
3 FLUTE 22" BEVEL REPLACEMENT CUTTER SOLID CARBIDE P A R T N O . 733129-8A FOR BEVEL TRIMMER /4" REPLACEMENT ARBOR PART NO. 1 /4 1-114 1 I 4 2.318 733131-2A FOR FLUSH TRIMMER ASSEMBLY NO. 733129-2A AND NO. 733129-4A BALL BEARING PILOT PART NO.
Page 19
Jan - 2 4 -'E6 EN mm (1/2") ROUTER Model 3612B...
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.