Table of Contents
Quick Links
Table of Contents
Related Manuals for Hitachi CPX14QE
Summary of Contents for Hitachi CPX14QE
- Page 1 CPX14QE OPERATING GUIDE FOR COLOUR MONITOR...
-
Page 2: Table Of Contents
OPERATING GUIDE ENGLISH - OPERATING GUIDE Contents (English) Safety Mains Supply Important note for the U.K. Plug Earthing Setup Operation & Volume Monitor Controls On Screen Help Volume Picture View Modes Dwell Time Screen & Output 1 Output 2 Output 3 Alarms Alarms History... -
Page 3: Uk Operating Guide
BEFORE OPERATING THIS EQUIPMENT Mains Supply This equipment is designed to operate on 220-240V AC 50Hz only. Do not operate on DC power supplies or other voltages. Before connecting to the mains, please read the following instructions carefully. Important for the U.K. The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. -
Page 4: Setup
Rear View of Monitor RS232 Video In Video Out For further details, please Video input Video in contact HITACHI Sales division. To VCR or from an external from cameras. (Refer to the back cover of this other monitor. device e.g. a VCR. -
Page 5: Operation & Volume
OPERATION Monitor Controls - cont. Once the monitor has been set up to your requirements using the menus as shown in this manual, you may find the following features useful. MENU - Press to show the Main Menu. BUTTON 1(LEFT) - Press to show Volume bar, then use the LEFT/RIGHT buttons to adjust the volume. -
Page 6: Picture
PICTURE The Contrast, Brightness and Colour can be individually adjusted and set for each camera in both full screen and quad modes. Follow the steps below to adjust each camera. Please Note : Only the Contrast, Brightness and Colour can be individually adjusted to suit each camera. -
Page 7: View Modes
Output 1 will always follow the picture and sound settings for the Screen option. Option 1 is for use with an external (larger) monitor, etc.) 2. HITACHI recommends the connection of a VCR to Output 2. Screen & Output 1 This has 7 different options available (CAMERA 1,2,3,4, CYCLE, QUAD(MANUAL) and QUAD(CYCLE) - please see next page for details). -
Page 8: View Modes
VIEW MODES CAMERA 1 CAMERA 2 Shows on screen the input from camera 1 Shows on screen the input from camera 2 only, with sound. only, with sound. CAMERA 3 CAMERA 4 Shows on screen the input from camera Shows on screen the input from camera 3 only, with sound. -
Page 9: Alarms
ALARMS This option enables the user to set an alarm to ring if the input from one of the attached cameras fails, either through a short circuit or signal failure. Please see below for details. Enter the Main Menu as previous and select Alarms. Press the LEFT/RIGHT buttons to confirm. -
Page 10: Install
MAIN MENU (MORE. . .) This option enables the user to enter further options in the Main Menu. These options allow you to set the language of the OSD’s, the date and time, to name each camera input and to change the picture highlighting preferences . -
Page 11: Memory Reset
MAIN MENU (MORE. . .) Memory Reset This option resets the monitor to its initial state, i.e. factory settings. Press the UP/DOWN buttons to select Memory Reset. Press the LEFT/RIGHT buttons to confirm The next screen will ask if you are sure you want to reset the memory. -
Page 12: Pip Labels
MAIN MENU (MORE. . . ) PIP Labels This option enables the user to choose whether they want the label of each camera displayed on screen and also the size of the label. Choose LARGE, SMALL or OFF as shown below. Press the UP/DOWN buttons to select PIP Labels. -
Page 13: Specifications
SPECIFICATIONS Picture Tube ................34cm Type A34EACO1X06 Mains Voltage ................220 - 240V AC 50 Hz Power Consumption ................38 Watts Speaker ......................8 Dimensions (W x H x D) cm .............37 x 35.5 x 38.5 Weight ......................11 kg EXTERNAL CONNECTORS Phono Connectors Audio Output - 0V5 nominal level - 0V2 minimum - 2V0 maximum at an impedance of less than 1K... -
Page 14: Guarantee
The product has been installed and used only in accordance with the instructions supplied with the product. The product has not been repaired, maintained, or modified by any person other than an HITACHI authorised engineer. iii) The product serial number has not been removed or altered. - Page 16 Fax: +46 (0) 8 562 711 13 Tel: +39 02 38073415 Servizio Clienti Email: [email protected] Fax: +39 02 48786381/2 Email: [email protected] HITACHI EUROPE S.A.S HITACHI EUROPE LTD (Norway) AB Lyon Office STRANDVEIEN 18 B.P. 45, 69671 BRON CEDEX 1366 Lysaker FRANCE...