VESA DPMS. ® The E emblem does not represent EPA endorsement NERGY of any product or service. ® As an E Partner, Hitachi,Ltd. has determined that this NERGY ® product meets the E guidelines for energy efficiency. NERGY...
Page 2
TCO’99 STATEMENT Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. This product meets the requirements for the TCO'99 scheme which provides for an international environmental and quality labelling of personal computers.
Page 3
Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): [email protected] Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants...
1/31/01 or 36 months for both panel and backlight if purchased after 1/31/01. In the event of a defect during this 12 month, 36 month or 60 month period, Hitachi America, Ltd. will, at its option, repair or replace the monitor at no charge except as set forth below.
DISCONTINUED OR REFURBISHED. For Canadian Customers only Warranty Policy Hitachi Industrial Products are guaranteed to be free from defects in workmanship and material. If any failure, resulting from either workmanship or material defects should occur under normal and proper usage within the period stated hereunder from the original provable date of purchase, such failure should be repaired at no cost to the buyer for labor and parts if the defective product is brought to an AUTHORIZED HITACHI SERVICE CENTRE in Canada.
Page 6
Company is authorized to change, modify, or extend its terms in any manner whatsoever. Hitachi Canada Inc. shall not be responsible for any damages or loss of any kind attributed to the product rendered defective during usage, or attributed to incompatibility problems of any linked equipment including software.
Colour/Color Monitor CML153XW USER MANUAL Congratulations on your selection of the HITACHI Colour/Color Monitor. Read the instructions inside carefully, and keep this user manual for future reference. NOTE: * The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual.
Page 8
Interface for Arm Applications ..................21 Connecting the Display to your Computer..............21 Connecting the AC Power ..................23 Connecting the Audio Cable..................23 Setting Up the LCD Monitor..................23 Power Management System ..................23 Chapter 2 Display Controls ...............24 User Controls ......................
Using this Display Safely Common Safety Precautions Please read carefully and make sure you fully understand the following safety precautions: Operations should be done according to instructions and procedures described in this manual. Make sure to heed all warnings displayed on the device and manual. Neglecting to do so may result in fire or damage the device.
Page 10
Handling and Operation Do not handle or operate in ways other than what is depicted in the manual. If there are any problems with the device, turn OFF the power, unplug the cord then notify the dealer where the product was purchased or call a service person. Taking ample care The cautions noted on the device and manual have been carefully considered.
Warning Abnormal heat, smoke, sounds or smells. If anything abnormal should happen, turn OFF the power and unplug the power cord. Continued use in this condition may lead to electrical shock or fire. The area around the cord should be clear to allow the cord to be easily unplugged.
Page 12
Placing Objects on the Device DO NOT put flower vases, planters, vessels containing water, pins and paper clips or other metal items on the device. If anything should fall in, using the product in this condition may result in electrical shock. Handling of the power cord Use the power cord supplied with the product and be careful of the following during use.
Impact from Dropping To not drop, bang or subject to physical shock. Using after such incidents may result in electrical shock or fire. Power Usage The usable voltage is 100-120V / 200-240VAC. DO NOT use any other voltage. This may result in electrical shock or fire.
Aluminium Electrolysis Condenser The electrolyte condenser used in the AC adapter has a limited life. If used past the life span (approximately 5 years), replace the AC adapter. Leakage or drying up of the electrolyte liquid may result in fire, electrical shock. This may also cause the device itself to malfunction.
Page 15
Stand When adjusting the angle, hold the top left and right edges with both hands and move slowly. Using only one hand may cause it to fall. DO NOT place your hand near the stand when adjusting the LCD forward or back. Your fingers may get caught and cause injury.
Page 16
Keep the plastic bag used to wrap the display away from young children. The bag may cause suffocation.
FCC Statement Warning WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
For the Customers in CANADA NOTICE : This Class B digital apparatus complies with Canadian ICES-003. For the Customers in the UK THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE UK PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value...
Page 19
As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured GREEN or GREEN and YELLOW.
Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot.
Detaching LCD Monitor from Its Stand 1. Remove the rear panel from the monitor. (see Fig. 1-2) 2. Unscrew screws of the hinge bracket 3. Remove the stand from LCD monitor Figure 1-2 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-2.
Page 22
comply with FCC regulations. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used.
Connecting the AC Power 1. Connect the power cord to the AC adapter. (See Fig. 1-5) 2. Connect the AC adapter's DC output connector to the DC Power Jack of the monitor. 3. Connect the power cord to an AC power source.
Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 PC Audio Stereo output. Stereo Speakers Speaker Volume Increase Volume - Turn knob to right direction. Control Decrease Volume - Turn knob to left direction. DC Power Switch Press the power switch to switch the monitor ON/OFF.
Function Description Icon Function Function Description Brightness This function increases or decreases the brightness of the image. This function increases or decreases the difference between the Contrast dark and light color. H. Position This function shifts the entire display image left or right. V.
Chapter 3 Technical Information Specifications LCD Panel Size 15.0" (38 cm) Display Type Active matrix color TFT LCD Resolution 1024 x 768 Display Dot 1024 x (RGB) x 768 Display Area (mm) 304 x 228 (H x V) Display Color 262K Brightness 200 cd/m...
Page 27
Power Management Power Mode AC Input LED Color Consumption* 25W maximum 240 VAC Green Standby** 5W maximum 240 VAC Yellow Suspend** 5W maximum 240 VAC Yellow Off** 5W maximum 240 VAC Yellow DC Power Off 5W maximum 240 VAC Dark Yellow: Standby, Suspend, Off Disconnected 5W maximum...
Pin Assignment Signal Signal Description Description Green Blue Digital GND Digital GND Digital GND H. Sync. Red Rtn V. Sync. Green Rtn Blue Rtn Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing.
Page 29
experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes. Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor. PROBLEM Picture is unclear and unstable The picture is unclear and unstable, please perform the following steps :...
Page 30
Fax: +46 (0) 8 562 711 13 Tel: +39 02 38073415 Servizio Clienti Email: [email protected] Fax: +39 02 48786381/2 Email: [email protected] HITACHI EUROPE S.A.S HITACHI EUROPE LTD (Norway) AB Lyon Office STRANDVEIEN 18 B.P. 45, 69671 BRON CEDEX 1366 Lysaker FRANCE...