Page 1
No. 0417 CML154XW SERVICE MANUAL MANUEL D'ENTRETIEN WARTUNGSHANDBUCH CAUTION: Before servicing this chassis, it is important that the service technician read the “Safety Precautions” and “Product Safety Notices” in this service manual. Data contained within this Service manual is subject to alteration for improvement.
1. 1. ELECTRICAL REQUIREMENTS ................2 A. LCD Panel Specification..........................2 B. CONTROLS .............................. 3 C. Power Management ..........................3 D. Display Modes FOR Inspections ....................... 5 2. ADJUSTMENT CONDITIONS..................6 A. Measuring Apparatuses Used ........................6 B. Input Signal..............................6 C.
B. CONTROLS B-1 Control panel (monitor front panel) 1. Power LED, ( Please refer to C-2 LED definition table) 2. Adjust decrease. 3. Adjust increase 4. Function select counter-clockwise. 5. Function select clockwise. 6. Power ON/OFF switch, push to ON and push to OFF. (toggle switch) C.
Page 5
C-2 LED definition Table State On mode Green Stand-by Yellow Suspend Yellow Off mode Yellow power off Dark 1. Yellow(stand-by; suspend; off mode) disconnection 2. LED Dark (power off) C-3 Power Consumption Meet VESA DPMS Proposal On mode 25 Wmax Stand-by 5 Wmax Suspend...
D. Display Modes FOR Inspections D-1 Supported Timing(for Not supported timing will go to power saving mode)T FH(KHZ) SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL TIMING FV(HZ) POLARITY (DOT/LINE) (DOT/LINE) WIDTH PORCH PORCH FOREQ. (DOT/LINE) (DOT/LINE) (DOT/LINE) (MHZ) 31.469 25.175 640x350 VGA-350 70.087...
2. ADJUSTMENT CONDITIONS A. Measuring Apparatuses Used Necessary measuring equipment that for the adjustment of LA-1221JMW’s MAIN PWB are following items. Adjusted Video Generator. Oscilloscope (more than 4 channels required) DC voltmeter B. Input Signal Input signal by using video signal generator with VGA Card port for this adjustment. C.
4. ADJUSTMENT OF BOARDS Equipment is connected with boards to be inspected before adjustments. Refer to diagram below. A. Connection Method A-1 VL547 For AU Panel and W/O Audio. 1. R.G.B Signal Cable 2. DC Power Cable 3. LCD Lamp Cables 4.
Page 9
VL542 For Hannstar Panel W/I Audio 1. R.G.B Signal Cable 2. DC Power Cable 3. LCD Lamp Cables 4. Control Cable 5. Audio Cable 6. Speaker and Wire / Connector...
5. DISPLAY CONTROL BOARD A. Description The VL-547 and VL-542 display control board is design to directly convert the R.G.B signals from VGA Card D-sub port to optimum LCD timing signals so as to construct a high display quality LCD monitor. B.
C-1 Sage Operation The s9050-100 is highly-integrated display processors. It has an ADC/PLL block and a microprocessor integrated on a single chip. The cost-effective s9050-100 is suitable for the XGA and the s9050 for the SXGA market segment with smaller memory requirements. Other features include a brand new high-end scaler, Active Color Management, a flexible OSD, Autoadjust, SureSync and independent monitoring of the analog interface.
E. Connector Type Location Type Maker Number of pins DZ11A91-L8 P1.524 FEMALE 96113-1003 E&T 96113-0703 E&T 98210-4011 E&T 98210-4011 E&T F. Connector pin assignment F-1 CN1 Pin NO. Signal Vertical Sync Horizontal Sync Blue Video Ground Blue Video Green Video Ground Green Video Red Video Ground Red Video...
Page 15
( VL-542 Control Board for Hannstar Panel )
Page 16
F-3 J2 Pin NO. Signal Comment NONE LED-Y Power saving mode LED-G Monitor is ON KEY-UP Function select counter-clockwise key KEY-Down Function select counter-clockwise key KEY-R Adjust up key KEY-L Adjust down key KEY-POWER Power ON/OFF key F-4 J3 Pin NO. Signal Comment VL547 / VL-542 power input...
6. VK-546 Control Panel Board A. Description The VK-546 is designed to offer an user interfaced control panel which passes and receives signals to and from power board . B. Connector and Switch Locations C. Connector type Location Type Maker Number of pins 96113-1113 E&T...
D. Connector pin Assignment D-1 J1 (Audio Function Only) Pin NO. Signal Comment MUTE1 Audio Mute RIN1 Audio volume adjust line IN R LIN1 Audio volume adjust line IN L RIN2 Audio volume adjust line OUT R LIN2 Audio volume adjust line OUT L R-EAR EAR Phone out R L-EAR...
Page 19
KEY-UP Function select up KEY-DOWN Function select down KEY-R Function select right KEY-L Function select left KEY-PWR Power ON/OFF signal D-5 VR1 (Audio Function Only) Volume control , clockwise for increasing ; counter-clockwise for decreasing D-6 Switch definition Location Definition Function select by clockwise direction Adjust down Adjust up...
7. POWER BOARD A. Description There are three kind of circuits in this power board-AC/AC, inverter and audio B. Electrical characteristics B-1 FOR HANNSTAR PANEL MIN. TYP. MAX. COMMENT INPUT VOLTAGE 11.4V 13.8V Vin=12V MAX. INPUT CURRENT -------- 1.2A BRIGHTNESS BACKLIGHT VOLTAGE 684Vrms 760V rms.
8. CIRCUIT DESCRPTION A. Micro-Controller Circuit The U5 (for VL-547 ) or U3 ( for VL-542 ) (s9050-100) is a system controller. The Y1 is 14.318MHz XTAL. B. Circuit of Plug and Play Plug and play allows the serial communication of host PC and peripherals offering minimal configurations to end users.
9. INTRODUCTION A. Front Panel Control and Led JS558(Without Audio) Front Panel Controls Item Control Function Press the power switch to switch the monitor DC Power Switch ON/OFF. LED lights Green color --- Power is ON. LED lights Yellow --- Monitor is in "Power DC Power-On Indicator Saving Mode".
Page 24
JS555(With Audio) Front Panel Controls Item Control Function PC Audio Stereo output. Stereo Speakers Increase Volume - Turn knob clockwise. Speaker Volume Control Decrease Volume - Turn knob counter clockwise Press the power switch to switch the monitor DC Power Switch ON/OFF.
B. Rear Panel connector Input Signals Rear Panel Cable and Connector Item Cable / Connector Function Signal Cable Connect the video port 2 AC IN Power Connect Connect the AC power cord Audio connector Connect the audio port (JS555 Only)