Related Manuals for Hitachi CM1473ME
Summary of Contents for Hitachi CM1473ME
- Page 1 ..,.’”-’ ‘“ COLOUR DISPLAY OPERATING GUIDE...
- Page 2 POWER SOURCE This colour display is designed to operate on 220/240 volts 50 Hz, AC. Insert the power cord plug into a 220/240 volts 50 Hz safety grounded outlet. DO NOT CONNECT THE DISPLAY TO OTHER THAN THE SPECI- FIED VOLTAGE. Never remove the back cover of the display as this can expose you to very high voltage and other hazards.
- Page 3 INTRODUCTION The Multi 560 (CM1473ME) from HITACHI is a high resolution colour display monitor that automatically adjust to horizontal scanning frequencies of graphics boards from 15.5 kHz to 35 kHz and vertical scanning frequencies from 50 Hz to 80 Hz.
- Page 4 Cautions when using the Multi 560 WARNINGS NEVER REMOVE THE BACK COVER Removal of the back cover shall be done only by qualified personnel. CORRECT VOLTAGE Use only the rated voltage supply. When the power voltage is extremely high or low, -”...
- Page 5 HOW TO USE (1) Signal cables are not supplied with this monitor. (2) Proper signal cables have to be obtained from dealer to suit your application. your Signal CGA, Personrd Olivetti source System/2 compatibles 9pin-9pin 9pin-15pin 9pin-25pin Signal cable SC–15 SC–09 SC–25 (12) Auto/...
- Page 6 Location and Description of User Controls 11111111111111] l[lllllllllllll mlllltllllllltllllll~ln- POWER SWITCH Press to turn the power ON. Press again to turn the power OFF. POWER ON INDICATOR A green light comes on when the power is ON. HORIZONTAL PHASE CONTROL This control adjust the horizontal position of the display data.
- Page 7 Q!E%$ TTL/ANALoGuE s~TcH By pressing this switch, input signals can be selected between analogue and TTL. * Avoid supplying both analogue and TTL signals at the same time since this may cause interferences between the signals (cross-talk). Both connectors can be connected at the same time.
- Page 8 When signals other than the recommended signal are received Cause Phenomenon Adjustment Picture width too wide. Data display period is more than standard timing. Adjust horizontal size control @) . Picture width too narrow. Data display period is less than standard timing. Adjust horizontal size control Picture deviates to...
- Page 9 Cause Phenomenon Adjustment Picture length Vertical blanking period is less than standard timing. much extended. $, ., .. ,, Adjust verticil sizecontrol @) . , :..Picture deviates upward. Vertical front porch is less than standard timing. ,,.
- Page 10 SPECIFICATIONS ‘====) 14”, 90-deg., In-Line, 0.31 mm dot pitch P22, Tinted glass (55%), Non-Glare (Silica) Analogue TTL level positive 0.6Vp-p/75-ohm positive R, G, B, I (16-colour) R, G, B Video Input Signal R, r, G, g, B,b (64-colour) H/V composite H, V separate TTL sync : 15.5 -35kHz...
- Page 11 (1) TTL input EGA 16/64-colour CGA 16-colour PIN No. Ground Ground Secondary Red No Connection Primary Red Primary Green Green Primary Blue Blue Intensity Secondary Green Secondary Blue Not comected Horizontal Sync Horizontal Sync Vertical Sync Vertical Sync (2) Analog input ~$c”...
- Page 12 SEPARATE SYNC. VIDEO HORIZONTAL VIDEO VERTICAL TIMING EXAMPLE AT MANUAL POSITION EXAMPLE OF TIMING REMARKS 15.75kHz 24.83kHz 30.lkHz 63.5 40.28 33.2 64.5 to 28.6/Js (15.5 to 35kHz) BJLS 5.08 3.04 3.43 2 to 1o/.ls 7.62 2.80 2.86 2 to 8.151M “~ 46.3 32.4...
- Page 13 Timing Position List at Auto Type Resolution 15.70 21.85 kHz Front porch 6.65 I us Svnc width 8.15 44.3 I us Distdav time 39,3 USTotal 63.7 45.8 Usfv Hz Front porch H Sync width H Back porch H Display time H Total H H.
- Page 14 You can set the colour monitor to the desired angle with the tilt stand supplied. CAUTION – This colour monitor may be used only with HITACHI exclusive tilt stand. Use with other tilt stands may result in instability causing possible injury.
- Page 15 MEMO...
- Page 16 — — TAC l-l 460373 Printed in Japan YN-N...