Page 1
SM0056 CMP205SXE SERVICE MANUAL CMP205SXU CMP205SXJ NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGEMENT VGA and XGA are registered trademarks of International Business Machines Corporation.
CONTENTS FEATURES ................................ 1 SAFETY GUIDELINES ............................2 ! WARNINGS ..............................3 ! CAUTIONS ..............................5 PRECAUTIONS ..............................7 FOR THE CUSTOMER IN CANADA ........................8 INSTALLATION ..............................9 STANDARD SETTINGS............................ 10 COMPONENT PARTS AND THEIR DESCRIPTIONS ..................11 OPERATION ..............................13 POWER SAVING FUNCTION...........................
SAFETY GUIDELINES This monitor is designed to be safe in normal usage. However, due to high internal voltages, fire or serious injury may occur unless you use this monitor in correct way. You are strongly suggested to follow the instruction shown below in order to avoid such injury. Keep to the safety guidelines Do not use the monitor if it fails If the following occur,...
WARNINGS Fire or electric shock may cause death or serious injury unless you follow the instruction below. n If you see smoke or an unusual smell comes from the monitor. Turn off the monitor and disconnect the power plug from the power point immediately. Request repair after confirming smoke is eliminated.
Page 5
WARNINGS Fire or electric shock may cause death or serious injury unless you follow the instruction below. n The enclosed power cord must be used ! Failure to do so may cause electric shock hazard or fire hazard. In USA/Canada, use a UL LISTED/CSA LABELLED or CERTIFIED power cord set meeting the following specifications : Rating: min.
WARNINGS Fire or electric shock may cause death or serious injury unless you follow the instruction below. n n FOR THE CUSTOMERS IN THE U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE.
Page 7
CAUTIONS Electric shock or other accidents may cause serious injury or damage to properties. n n CAUTION for 200 - 240V operation only This equipment relies on the protective devices in the building installation for short-circuit and over-current protection. Refer to the following table for the suitable type and location of the protective devices which should be provided in the building installation.
PRECAUTIONS n n Installation environment Do not block ventilation holes. Do not put the monitor on carpet or blanket, or other materials which could block the ventilation holes. Do not put the monitor in the following places. • Near heat sources or exposed to the direct sunshine. •...
n n Display stand The monitor can swivel though 45 degrees both clockwise and counter-clockwise and adjusts 3 degrees in downward and 8degrees in upward directions. All adjustments should be done using both hands. (To tilt towards the front, push the bottom of the monitor.) ! WARNING §...
INSTALLATION n n Package Contents Your CMP205SX package includes: ü CMP205SX monitor ü Signal Cable ü Power Cord ü User Manual (current manual) Please check immediately after opening the packaging and contact your supplier immediately if any items are missing or damaged. Also be sure to keep the packaging for use for future moving or shipping.
STANDARD SETTINGS Microprocessor-based preset functions can store adjusted settings. The industrial standard settings have been pre-programmed by the factory. Pre-programmed settings are as follows. In addition, more 15 user settings can be stored. Display mode Resolution H-frequency V-frequency Sync-polarity Scanning mode NEC 640x400-56 x 400 24.83 kHz 56.42 Hz...
COMPONENT PARTS AND THEIR DESCRIPTIONS ¬ MENU BUTTON Press to display or clear the menu screen. - c CONTRAST ' / $ BUTTON This button can be used to adjust contrast. Within the menu it is also used to select and change menu functions.
Page 13
15P mD-sub 13W3 Signals (Enclosed signal cable) (Video input terminal) Center of A1 R Video Center of A2 G Video Center of A3 B Video ------- N.C. Outer of A1 GND (R Video Return) Outer of A2 GND (G Video Return) Outer of A3 GND (B Video Return) -------...
OPERATION n EasyMenu for Display Adjustment This monitor has OSD Menu for display adjustment. (EasyMenu) Press MENU button for displaying the menu. The menu has 2 modes (MENU 1 & MENU 2), and you can follow the numbered steps in sequence as shown below.
Page 15
n n Adjustment & Setting (1) Contrast CONTRAST adjusts foreground white level of screen image. : increases contrast : decreases contrast ENTER : saves an adjusted value and closes MENU. MENU : returns to previous adjustment state and closes MENU. Those adjustments are valid for all input signals.
Page 16
(5) H. Position H. POSITION adjusts horizontal position. : moves display image to the right. : moves display image to the left. ENTER : saves an adjusted value and closes MENU. MENU : returns to previous adjustment state and closes MENU. The adjusted values are automatically saved and MENU is closed unless adjustment is done within 15 seconds.
Page 17
The adjusted values are automatically saved and MENU is closed unless adjustment is done within 15 seconds. (10) Auto Scaling Mode AUTO SCALING MODE sets a display enlarging mode. : enlarges a display image to almost full screen when an Input signal is same as or less than SVGA (800x600).
Page 18
1. Background Mode Background Mode changes background of OSD Menu. Blue Back : sets background color blue. See Through : sets transparent background ENTER : executes a setting and saves its value and then close MENU. MENU : makes a setting invalid and closes MENU. Those adjustments are setting for Background color of OSD Menu.
(15) Exit Used to exit from the Adjust/settings menu. (16) Hf/Vf Hf/Vf displays horizontal frequency(Hf) and vertical frequency(Vf) of input signals. No adjustment or setting capabilities are provided. POWER SAVING FUNCTION This PDP monitor comes with a VESA DPMS power conservation mode. When in power saving mode, the indicator lamp will light up in orange, and the display will enter one of the states indicated in the following table depending on the computer system to which it has been connected.
Page 20
Symptom Cure monitor generating excessive levels of EMI/RFI noise. -Connect the monitor to another power source. Surface temperature of display -Plasma display panels discharge electricity within the panel to too high. generate light. While this may cause the temperature of the surface of the panel to rise, it does not indicate the existence of any problems.