1. Manuals
  2. Brands
  3. HP Manuals
  4. Storage
  5. StorageWorks 7100 - Virtual Array
  6. Appendix

HP StorageWorks 7100 - Virtual Array Appendix page 14

Appendix a. disk array controller log
Hide thumbs Also See for StorageWorks 7100 - Virtual Array:
FC-SCSI Interface SpecificationDescribes the IceCube SCSI interface. Targetted as part of OEM manual.Disk Array Con
Event
Event
Number
Name
(dec/hex)
314/0x13a
Drive Missing At Power On
315/0x13b
RAM Image Upload Failed
316/0x13c
Old Cache Configuration Used
317/0x13d
Incompatible RAM Image
Content
318/0x13e
Disk Interface Underrun Event
319/0x13f
Disk Interface Overrun Event
320/0x140
Disk Interface Timeout Event
321/0x141
Controller ECC Miscorrection
322/0x142
Controller Data Bus
Microprocessor Access Error
323/0x143
Incompatible Address Table In
RAM Image
324/0x144
Non-Volatile Memory
Initialized
325/0x145
Battery Failed Discharge Test
326/0x146
Fan Failed
327/0x147
Power Supply Failed
328/0x148
Power Down Due To Fan
Predictive
Suspected
Maintenance
Components
Implication
Y
Ignore unless no
Disk Drive,
Operator activity
Controller,
Back End FC
Link
Y
Single
Disk Drives,
Occurrance
Controller,
Back End FC
Link
Y
Ignore - See
None
errors associated
with shut down
Y
Ignore - Operator
None
error
Y
Single
Disk,
Occurrance not
controller, disk
with other entries
interface
Y
Single
Disk,
Occurrance not
controller, disk
with other entries
interface
Y
> 2 occurrances
Disk,
per hot plug
controller, disk
insert or removal
interface
Y
Single
SIMM,
Occurrance
Controller
Y
Single
Controller
Occurrance
Y
Ignore - Operator
None
error
Y
Ignore unless no
SDRAM
operator activity
DIMM,
Controller
Y
Single
Battery
Occurrance
Y
Single
Fan, Controller,
Occurrance
Backplane
Y
Single
Power Supply,
Occurrance
Controller,
Backplane
Y
Single
Fans,
Error! No text of specified style in document.
Description
used.
N
This error code indicates that a drive was discovered
to be missing during a power on or reset. This event
occurs for volume set members only. The device
number of the drive removed appears in this change
record. A device number consisting of the
controller serial number followed by a 0 indicates
that the device number has not yet been assigned.
N
The subsystem was unable to upload a usable disk
copy of NVRAM during startup. System state is
NO_MAPS.
N
Write data found in the uploaded NVRAM image
blocked a requested transition to a new cache
configuration; the previous configuration is being
used. To get to the new configuration, get cache
flushed and do another upload.
N
This is an error detected by the startupSystem when
the current RAM config is not compatible with the
RAM config of the NVRAM disk image. This is
similar to except that not enough physical RAM
space is not the problem but rather a different
mapping of NVRAM in the disk image that cannot
be supported by the current config (i.e., the image
supports 8G drives but the current config does not).
A new VS is created. System state is NO_MAPS.
To use the disk image the current config must be
updated to the disk config.
N
An attached device sent/received less data than
expected.
N
An attached disk sent/received more data than
expected.
N
A command to an attached disk did not complete
within the allotted time.
N
This error code indicates that the system
experienced a correctable error which was mostlikly
misscorrected.
N
This error code indicates that the system
experienced a uP access error without the needed
other qualifiers. Microprocessor access errors
should only occur in conjunction with correctable or
uncorrectable memory errors, or with parity errors.
If no other condition is present this event is reported
to indicate the malfunction.
N
This error occurs when NVRAM (SIMM(S)) is
removed, forcing the Time Stamp Table to shrink,
or the image to be reloaded has an invalid size.
Once NVRAM is added and the Table is expanded,
it cannot shrink.
N
This message is logged when NV-SDRAM is found
to be invalid at boot and must be initialized. This
should not cause concern if memory was purposely
invalidated or a new board or new memory has just
been installed.
N
This error code indicates that a battery has failed the
long discharge test. This test occurs following
power on and every 30 days thereafter. The test
takes about 36 hours to complete. Replace
Batteries.
N
This error code indicates that a fan has failed.
N
This error code indicates that a power supply has
failed.
N
This error code indicates that the Background
loading

Related Manuals for HP StorageWorks 7100 - Virtual Array

Related Products for HP StorageWorks 7100 - Virtual Array