HP P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade Installation Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. P5389A - Intel Pentium III-S 1.4 GHz Processor...
  6. Installation manual
HP P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade Installation Manual

HP P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade Installation Manual

Hp windows server 2003 for ia-32 general installation guide
Hide thumbs Also See for P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade:
Table of Contents

Quick Links

See also: Technical White Paper, Installation Manual
HP Windows Server 2003 for IA-32 General
Installation Guide
(This document is only available in English.)
April 11, 2003
Preparing your HP Server for your NOS installation

Hardware Setup

Prepare your HP server following the instructions in the HP Installation Guide provided for your server model.
It is recommended that you do not install any third party adapter until you verify that the HP equipment is functioning
properly and you complete the NOS installation.
Preparing your Hard Disk Drives
Your HP Server comes with new hard disk drive(s) that do not need specific setup. If you install additional and/or USED
hard disk drives in your new server HP recommends you perform one of the following:
·
If you have an HP SCSI RAID card then you must setup the Logical Drives following the procedures outlined by the
HP Installation Guide provided with the card.
·
If you are using the IDE RAID controller FastTrack 100 TX2, you must connect the hard disk drives to the
controller following instructions in the FastTrack User Guide. The RAID setup for this controller is performed at
the BIOS level when the system starts up. When prompted, press F to get into it, 3 to define the array,
to select the array to change the array, Down arrow to go to the available drives and space to
select which drives you want in this array. Then Y to save it. Finally, Y to exit back to
the main menu and reboot.
·
If you wish to recycle used hard disk drives:
Perform a media check
o
Use a utility such as fdisk to erase all data and partitions from your hard drive.
o
Updating your Server BIOS
HP recommends that you update your server BIOS with the latest system BIOS version to enjoy the most recent
compatibility fixes.
On the Internet you can obtain the latest BIOS for your system at:
http://welcome.hp.com/country/us/eng/software_drivers.htm
Follow the instructions for making a bootable floppy diskette and flashing the BIOS, if it is newer than your existing BIOS.
Installing Microsoft Windows Server 2003, Enterprise Edition
Prepare the Installation
Please refer to the Chapter 1 "Preparing your HP Server or your NOS installation" for our recommendations on the server
preparation.
Then gather the following material:
·
Microsoft Windows Server 2003 CD-ROM as well as the latest Microsoft Windows Server 2003 Service Pack (if
available).
·
Blank formatted 3.5-inch diskettes (if needed for drivers update).
·
Two or more clients for testing purpose (Optional)
by entering your product model number and downloading.
1
Table of Contents
loading

Related Manuals for HP P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade

Summary of Contents for HP P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade

  • Page 1: Hardware Setup

    HP Windows Server 2003 for IA-32 General Installation Guide (This document is only available in English.) April 11, 2003 Preparing your HP Server for your NOS installation Hardware Setup Prepare your HP server following the instructions in the HP Installation Guide provided for your server model. It is recommended that you do not install any third party adapter until you verify that the HP equipment is functioning properly and you complete the NOS installation.

  • Page 2: High Level Process Flow

    High Level Process Flow · Perform Windows Server 2003 Installation. · Complete the Installation (Microsoft Service Pack (if available), HP drivers, Recovery Console). · Configure the System. · Configure the Network. · Install additional HP accessories. Create the Driver Diskettes ·...
  • Page 3 At the "Windows Setup – Personalize Your Software" window enter your name, organization and click "Next". 10. At the "Windows Setup – Your Product Key" enter your Microsoft Windows Server 2003 product key. Example: ABCDE-12345-FGHIJ-67890-KLMNO 11. At the "Windows Setup – Licensing Modes" select the appropriate licensing mode according to your licensing for this server (default: per server number of concurrent connections 5) and click "Next".

  • Page 4: Completing The Installation

    19. At the "Logon to Windows" window enter the Administrator's password. 20. Click the "OK" button. 21. At the "Manage Your Server" window right click on the black X box at the top right of the screen. This will close this window, as we will postpone the customization of your server until completion of all the installation steps.

  • Page 5: Configure The Network

    · Question (?) means that the device is unknown. Note: If (!) or (?) symbols are reported then double click on each of the devices with (!) or (?). Use the "Device Status" message for troubleshooting. Or if a printer is available, use the View, Print from the menu to get a report.
  • Page 6 2. Create users using the Windows Server 2003 Computer Management utility: Start | Programs | Administrative Tools | Computer Management | System tools | Local Users and Groups | Users. 3. Connect clients PC to the network your HP server operates on. 4.

  • Page 7: Troubleshooting

    To expedite release of new products, HP may ship drivers without signature files. All Windows drivers provided by Hewlett-Packard are submitted to Microsoft for certification testing. Upon completion of testing, Microsoft produces signature files. HP then posts the revised driver package at http://welcome.hp.com/country/us/eng/support.html.
  • Page 8 Recovery option #2: Safe Mode Boot Activated by pressing F8 during the OS boot. It provides a minimal configuration with required drivers and services. The safe boot provides these options: Safe Mode. Windows only loads required files and drivers (i.e. Mouse, keyboard, base video, etc.) Excludes network services.

  • Page 9: On-Line Information And Software Sources

    3. The system will display a menu asking to select the instance of the NOS you want to boot. For example it displays: 1: C:\WINNT 4. Type 1 then Enter. 5. Type the administrator password when prompted. 6. At the command prompt type help and proceed to achieve your objective. 7.

This manual is also suitable for:

Tc2100Tc2110Tc4100Tc3100

Table of Contents