1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Industrial Equipment
  5. SIMATIC NET RUGGEDCOM RX1512
  6. Equipment manual

Siemens SIMATIC NET RUGGEDCOM RX1512 Equipment Manual

Rugged multi service platforms
Hide thumbs Also See for SIMATIC NET RUGGEDCOM RX1512:
Table of Contents

Quick Links

Edition
10/2023
Equipment Manual
SIMATIC NET
Rugged multi service platforms
RUGGEDCOM RX1512
https://www.siemens.com/ruggedcom
Table of Contents
loading

Related Manuals for Siemens SIMATIC NET RUGGEDCOM RX1512

Summary of Contents for Siemens SIMATIC NET RUGGEDCOM RX1512

  • Page 1 Edition 10/2023 Equipment Manual SIMATIC NET Rugged multi service platforms RUGGEDCOM RX1512 https://www.siemens.com/ruggedcom...
  • Page 2 Preface Introduction Installing the Device SIMATIC NET Device Management Rugged multi service platforms RUGGEDCOM RX1512 Modules Technical Specifications Equipment Manual Certification 10/2023 C79000-G8976-1057-25...
  • Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.

  • Page 4: Table Of Contents

    SIMATIC NET glossary ......................vi Registered trademarks ......................vi Warranty ..........................vii Training ..........................vii Customer support ......................... viii Contacting Siemens ......................viii Introduction ........................... 1 Feature Highlights ....................1 Description ......................1 Required Tools and Materials ................. 3 Decommissioning and disposal ................3 Cabling Recommendations ..................
  • Page 5 Table of contents Technical Specifications ...................... 27 General specifications ..................27 Chassis Specifications ..................27 Power Supply Specifications ................27 Failsafe Relay Specifications ................27 Operating Environment ..................28 Mechanical Specifications ..................28 Dimension Drawings ................... 28 Certification ......................... 31 Approvals ......................

  • Page 6: Preface

    Siemens' products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customer's exposure to cyber threats.

  • Page 7: Supplementary Documentation

    SIMATIC NET glossary The SIMATIC NET glossary describes special terms that may be used in this document. The glossary is available online via Siemens Industry Online Support (SIOS) at: https://support.industry.siemens.com/cs/ww/en/view/50305045 Registered trademarks The following and possibly other names not identified by the registered trademark sign ®...

  • Page 8: Warranty

    Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void.

  • Page 9: Customer Support

    Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit https://w3.siemens.com/aspa_app/?lang=en. Mobile app Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device and be able to: •...

  • Page 10: Introduction

    Introduction The RUGGEDCOM RX1512 is a cost-efficient, rugged Layer 3 switch and router. The RUGGEDCOM RX1512’s modular and field replaceable platform can be equipped with WAN, serial, and Ethernet options, making it ideally suited for electric power utilities, the industrial plant floor, and traffic control systems. The appliance’s compact form factor makes it ideal for pole mount applications or installation in restricted spaces.
  • Page 11 Introduction 1.2 Description Utility USB Port RS232 Serial Console Port (RJ45) Lamp Test/Alarm Cut-Off (LT/ACO) Button Management Port Compact Flash Card Port Alarm Indicator LED Power Status LEDs Port Status LEDs Figure 1.1 RUGGEDCOM RX1512 Management Port This 10/100Base-T Ethernet port is used for system management that is out-of-band from the switch fabric.

  • Page 12: Required Tools And Materials

    WEEE directive 2012/19/EU for the disposal of electrical and electronic equipment. Do not dispose of devices at public disposal sites. For environmentally friendly recycling and the disposal of devices, contact a certified disposal company for electronic scrap or your Siemens contact. For more information, refer to https://support.industry.siemens.com/cs/ww/en/ view/109479891.

  • Page 13: Cabling Recommendations

    Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions.
  • Page 14 Introduction 1.5.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations Cabling 1000Base- Required Action Category TX Compliant > 6 Connector and wiring standards to be determined. Follow these recommendations for copper data cabling in high electrical noise environments: • Data cable lengths should be as short as possible, preferably 3 m (10 ft) in length.
  • Page 15 Introduction 1.5.2 Gigabit Ethernet 1000Base-TX Cabling Recommendations RUGGEDCOM RX1512 Equipment Manual, 10/2023, C79000-G8976-1057-25...

  • Page 16: Installing The Device

    Installing the Device This chapter describes how to install the device, including mounting the device, installing/removing modules, connecting power, and connecting the device to the network. DANGER Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing any maintenance tasks, make sure all power to the device has been disconnected and wait approximately two minutes for any remaining energy to dissipate.

  • Page 17: General Procedure

    This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens Canada Ltd. could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment.

  • Page 18: Unpacking The Device

    Visually inspect each item in the package for any physical damage. Verify all items are included. Note If any item is missing or damaged, contact Siemens for assistance. Mounting the Device The RUGGEDCOM RX1512 is designed for maximum mounting and display flexibility.

  • Page 19: 2.3.2 Mounting The Device To A Panel

    Installing the Device 2.3.2 Mounting the Device to a Panel Panel/DIN Rail Adapter DIN Rail Screw Figure 2.1 DIN Rail Mounting Install one of the supplied screws on either side of the device to secure the adapters to the DIN rails. 2.3.2 Mounting the Device to a Panel For panel installations, the RUGGEDCOM RX1512 can be equipped with panel/DIN rail adapters pre-installed on each side of the chassis.

  • Page 20: Connecting The Failsafe Alarm Relay

    Installing the Device 2.4 Connecting the Failsafe Alarm Relay Screw Panel/DIN Rail Adapter Figure 2.2 Panel Mounting Prepare the mounting holes Align the device with the mounting holes and secure it to the panel. Connecting the Failsafe Alarm Relay The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is closed when the unit is powered and there are no active alarms.

  • Page 21: Connecting Power

    Installing the Device 2.5 Connecting Power Normally Closed Common Normally Open Figure 2.3 Failsafe Alarm Relay Wiring Connecting Power The RUGGEDCOM RX1512 supports a single low DC power source. DANGER Electrocution hazard – risk of serious personal injury or death Make sure all power sources are off before servicing the power module terminals. Make sure the power source is off before servicing the power terminal.

  • Page 22: 2.5.1 Connecting Low Dc Power

    Installing the Device 2.5.1 Connecting Low DC Power 2.5.1 Connecting Low DC Power To connect a low DC power supply to the device, do the following: NOTICE Electrical hazard – risk of damage to equipment Do not connect AC power cables to a 12, 24 or 48 VDC power supply terminal block. Damage to the power supply may occur.
  • Page 23 Installing the Device 2.5.1 Connecting Low DC Power Surge Ground Terminal Positive (+) Terminal Chassis Ground Terminal Negative (-) Terminal Jumper Chassis Ground Connection Figure 2.5 DC Terminal Block Wiring for Negative VDC Power Supplies Note For secure, reliable connections under severe shock or vibration, use M3.5 ring tongues with a maximum outer diameter of 7 mm (0.28 in).

  • Page 24: Testing Dielectric Strength

    Installing the Device 2.5.2 Testing Dielectric Strength #10 Ring Tongue #10-32 Screw Connection from External Power Source Chassis Ground Connection Figure 2.6 Chassis Ground Connection Install the safety cover over the terminal block. This is mandatory for 48 VDC and -48 VDC power supplies. 2.5.2 Testing Dielectric Strength Before performing any dielectric strength or HIPOT (High Potential) testing on the...
  • Page 25 Installing the Device 2.5.2 Testing Dielectric Strength Surge Ground Terminal Positive (+) Terminal Chassis Ground Terminal Negative (-) Terminal Jumper Chassis Ground Connection Figure 2.7 Jumper Connect one terminal from the HIPOT tester to the positive terminal and the negative terminal. Connect the second terminal of the HIPOT tester to chassis ground terminal.

  • Page 26: Device Management

    It may cause damage to the contact pins of the RJ45 ports. For a permanent solution, use Siemens 6XV1870-3Qxxx certified cables (manufactured December 2019 or after) or equivalent. Siemens recommends using Siemens certified cables and connectors for Siemens RUGGEDCOM products.
  • Page 27 Device Management 3.1 Connecting to the Device Serial Console and Management Ports Connect a workstation directly to the serial console or management ports to access the boot-time control and RUGGEDCOM RX1512 interfaces. The serial console port provides access to RUGGEDCOM RX1512's console interface, while the management port provides access to RUGGEDCOM RX1512's console and Web interfaces.

  • Page 28: Configuring The Device

    Device Management 3.2 Configuring the Device Name Description Receive Data- Transmit Data+ Reserved (Do Not Connect) Reserved (Do Not Connect) Transmit Data- Reserved (Do Not Connect) Reserved (Do Not Connect) Communication Ports Connect any of the available Ethernet ports on the device to a management switch and access the RUGGEDCOM RX1512 console and Web interfaces via the device's IP address.
  • Page 29 The following will void the warranty and potentially result in configuration data corruption/loss: • Using a CF card not approved by Siemens for use with this device • Removing the CF card in any scenario other than those described in this section...
  • Page 30 Device Management 3.3 Accessing the CompactFlash Card Remove the CF card access panel. Ejector Button CompactFlash Card Access Panel Figure 3.5 Removing the CF Card Press the ejector button to the left of the CF card and then pull the card out. Secure the CF card access panel to the chassis.
  • Page 31 Device Management 3.3 Accessing the CompactFlash Card RUGGEDCOM RX1512 Equipment Manual, 10/2023, C79000-G8976-1057-25...

  • Page 32: Modules

    Modules The RUGGEDCOM RX1512 features slots for up to two field-replaceable line modules, which can be used to expand and customize the capabilities of the device to suit specific applications. A variety of modules are available, each featuring a specific type of communication port: copper Ethernet, fiber optic Ethernet, SFP, WAN, cellular modem and DDS.

  • Page 33: Available Modules

    A variety of modules are available for use with the RUGGEDCOM RX1512. For more information, refer to the "RUGGEDCOM Modules Catalog [https:// support.industry.siemens.com/cs/us/en/view/109747072]" for the RUGGEDCOM RX1512. Installing/Removing Line Modules Upon installing a new line module in the device, all features associated with the module are available in RUGGEDCOM RX1512.
  • Page 34 Modules 4.3 Installing/Removing Line Modules Module Chassis Screw Figure 4.2 Removing a Module Install a new module or a blank module (to prevent the ingress of dust and dirt). [Optional] If necessary, install the device in the rack. Installing a Module To install a line module, do the following: [Optional] If the device is installed in a rack, remove it from the rack.
  • Page 35 Modules 4.3 Installing/Removing Line Modules Chassis Screw Figure 4.3 Installing a Module Tighten the screws to secure the module. [Optional] If necessary, install the device in the rack. RUGGEDCOM RX1512 Equipment Manual, 10/2023, C79000-G8976-1057-25...

  • Page 36: Technical Specifications

    Technical Specifications This section provides important technical specifications related to the device. General specifications Insulation Class I Overvoltage category OVC II Chassis Specifications Power Consumption 10 W Power Supply Specifications Note When determining cable lengths, make sure the nominal input voltage for the power supply is provided at the power source.

  • Page 37: Operating Environment

    Technical Specifications 5.5 Operating Environment Operating Environment The RUGGEDCOM RX1512 is rated to operate under the following environmental conditions. Note Temperature limits for select line modules may differ from that which can be withstood by the RUGGEDCOM RX1512. Make sure the selected modules are rated for the expected environmental conditions before deployment.
  • Page 38 Technical Specifications 5.7 Dimension Drawings 111.8 Figure 5.1 Overall Dimensions RUGGEDCOM RX1512 Equipment Manual, 10/2023, C79000-G8976-1057-25...
  • Page 39 Technical Specifications 5.7 Dimension Drawings 160.5 152.4 150.4 78.2 Figure 5.2 Panel and Din Rail Mount Dimensions 162.5 151.4 19.7 Figure 5.3 Line Module Dimensions 162.5 151.8 40.6 Figure 5.4 Power Module Dimensions RUGGEDCOM RX1512 Equipment Manual, 10/2023, C79000-G8976-1057-25...

  • Page 40: Certification

    Modules Catalog" for the device available online. Approvals This section details the standards to which the RUGGEDCOM RX1512 complies. Note All relevant certificates and test reports are available on Siemens Industry Online Support [https://support.industry.siemens.com/cs/ww/en/ps/16008/cert]. 6.1.1 UKCA This device is certified for use in Great Britain and bears the United Kingdom Certified Assessed (UKCA) marking.

  • Page 41: European Union (Eu)

    Certification 6.1.3 European Union (EU) 6.1.3 European Union (EU) This device is declared by Siemens Canada Ltd. to comply with essential requirements and other relevant provisions of the following EU directives: • Directive 2014/30/EU Directive 2014/30/EU of the European Parliament and of the Council of 26...

  • Page 42: Fcc

    Title 21 Code of Federal Regulations (CFR) – Chapter I – Sub-chapter J – Radiological Health 6.1.6 ISED This device is declared by Siemens Canada Ltd. to meet the requirements of the following ISED (Innovation Science and Economic Development Canada) standard: • CAN ICES-3 (A)/NMB-3 (A) 6.1.7...

  • Page 43: Rohs

    Certification 6.1.8 RoHS 6.1.8 RoHS This device is declared by Siemens Canada Ltd. to meet the requirements of the following RoHS (Restriction of Hazardous Substances) directives for the restricted use of certain hazardous substances in electrical and electronic equipment: • EU RoHS Directives (EU) 2011/65 and (EU) 2015/863 European Directive for Restriction of Hazardous Substances •...
  • Page 44 Signal ports 5 kV (Failsafe Relay output) DC Power Ports 5 kV Siemens-specified severity levels. EMC Immunity Type Tests for IEEE 1613 Note RUGGEDCOM products meet Class 1 requirements for copper Ethernet configurations and Class 2 for fiber Ethernet configurations. Class 1 allows for temporary communication loss, while Class 2 requires error-free and interrupted communications.
  • Page 45 Certification 6.2 EMC and Environmental Type Tests Description Test Levels 1 kV differential mode @ 1 MHz Radiated RFI Enclosure ports 35 V/m Enclosure Contact ± 8 kV Enclosure Air ± 15 kV Environmental Type Tests Test Description Test Levels Severity Levels IEC 60068-2-1 Cold Temperature...
  • Page 46 For more information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens Canada Ltd. Digital Industries Process Automation 300 Applewood Crescent Concord, Ontario, L4K 4E5 Canada © 2023 Siemens Canada Ltd. Subject to change...

Table of Contents