Quick Links
1.) Read these instructions.
2.) Keep these instructions.
3.) Heed all warnings.
4.) Follow all instructions.
5.) Do not use this apparatus near water.
6.) Clean only with dry cloth.
7.) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11.) Only use attachments / accessories specified by the manufacturer.
12.) Unplug this apparatus during lightning storms or when unused for long periods of time.
13.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
14.) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
15.) The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on apparatus.
16.) Mains plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus from the
mains completely, the mains plug should be disconnected from the mains
socket outlet completely.
17.) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
PRÉCAUTION: Danger d'explosion si les piles sont remplacées de facon incorrect. Remplacer
les piles seulement par le méme type de pile ou l'équivalent.
Remove any descriptive labels,stickers or protective films on the front or top
of the cabinet,if any.
Front Panel
1
2
3
4
Top Panel
10
TIME
CLOCK
ZONE
SET
ON/OFF BAND
STO.
MEM.
TUNE− TUNE＋ VOL− VOL＋
SNOOZE
DIMMER
SLEEP
11 12 13 14
15
16 17 18 19
11.) TIME ZONE/ ON/OFF Button
12.) CLOCK SET/ BAND Select Button
13.) AL1 Setting/ STO.(Store) Button.
14.) AL2 Setting/ MEM.(Memory) Button
15.) SLEEP/ SNOOZE/ DIMMER Button
16.) ◀ Set-/Tune- Button
17.) ▶ Set+/Tune+ Button
7.) MHz (FM Radio) Indicator.
18.) ▼ Down/Volume- Button
19.) ▲ Up/Volume+ Button
8.) KHz (AM Radio) Indicator.
20.) Time/Date Display
9.) AM Indicator ('On'=AM,'Off'=PM)
10.) AC adapter (Back Cabinet).
21.) Speaker(Top Cabinet)
press and hold
until the
display'Flashes'
Release
Checking the Current Year-Date-Day of Week-Time Settings
Press briefly the CLOCK SET button repeatedly to see the cycle of
year, date, day of week and time. To restore time display mode,
leave it idle for few secs.
Setting the Year
the CLOCK SET button until the Year 'Flashes',
the button;
Press the
or
button to adjust the Year;
Setting the Date
Press the CLOCK SET button again and release, the Date 'Flashes';
Press the
or
button to adjust the Month;
5
For example, May 21th will appear as '5.21';
Setting the Time
6
Press the CLOCK SET button again and release,
the Hour 'Flashes';
7
Press the
or
button to adjust the Hour (where AM
indicator 'On' is AM, 'Off' is PM);
Press the
or
button to adjust the Minutes;
8
Press the CLOCK SET button again, or leave
9
it idle for few seconds, to store all new settings
and restore it to time display mode.
Note：Time zone and clock settings can only be adjusted in Standby mode,where the
AM/FM Radio is disabled(i.e.the indicators of kHz and MHz are'Off')
9
8
7
6
5
21
Adjusting The Wake Up Time and Alarm Week Mode
IMPORTANT:Alarm settings can only be adjusted in Standby mode.
you may use one alarm for weekdays and the other for weekend wake up times.The
procedure for adjusting the wake up times is the same for both Alarm1and Alarm2.
•Press and hold either the AL1 or AL2 button until the display blinks and changes from
the current time to the Alarm 1 or Alarm 2 wake up time.
20
•Release the AL1(AL2) button,press the◀or▶button to adjust Hour
▼ or▲to adjust Minutes.
•Press the AL1(AL2) button again,Alarm Week Mode will blink .Press the ◀ or▶
button repeatedly to select your desired Alarm Week Mode:d1-7,d1-5 or d6-7
•Press the AL1(AL2) button again to store the alarm setting and resume to clock mode.
week
d1-7
d1-5
d6-7
Week
it
week
Week
Press◀or▶to select week mode.
Week
and hold
Alarm Week Mode
◀
▶
press the
pressandholdtheAL1
time.Press
press
Press
Alarm Week Mode
Related Manuals for Emerson SmartSet CKS1900
Summary of Contents for Emerson SmartSet CKS1900
- Page 1 PRÉCAUTION: Danger d’explosion si les piles sont remplacées de facon incorrect. Remplacer les piles seulement par le méme type de pile ou l’équivalent. press and hold until the display‘Flashes’ Remove any descriptive labels,stickers or protective films on the front or top of the cabinet,if any.
- Page 2 band the BAND BAND Press the ON/OFF button to turn ON the radio first. Then press (default sleep timer setting). steps below: briefly CLOCK SET STO. previous page to ON/OFF button once. STO. Follow the instructions on sections Setting the Year/Date/Time to set the clock to the correct year,date and time Press the CLOCK SET button repeatedly to check the year,date and time.