1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Scanner
  5. YOUJIE YJ-HH360
  6. User manual

Honeywell YOUJIE YJ-HH360 User Manual

Linear scanner
Hide thumbs
Table of Contents

Quick Links

YJ-HH360
Linear Scanner
User's Guide
™
Table of Contents
loading

Related Manuals for Honeywell YOUJIE YJ-HH360

Summary of Contents for Honeywell YOUJIE YJ-HH360

  • Page 1 YJ-HH360 Linear Scanner User’s Guide ™...
  • Page 2 Disclaimer Youjie reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Youjie to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of Youjie.

  • Page 3: Table Of Contents

    USB HID POS ............2-3 USB Serial Commands ..........2-3 USB Serial Emulation..........2-3 CTS/RTS Emulation ..........2-4 ACK/NAK Mode............. 2-4 Honeywell Bioptic Aux Port Configuration....2-4 ® Datalogic™ Magellan Bioptic Aux Port Configuration ............... 2-5 Keyboard Country Layout ........... 2-5 Keyboard Mode Options ...........
  • Page 4 RS-232 Handshaking..........2-22 RS232 Timeout ............ 2-24 XON/XOFF ............2-24 ACK/NAK ............. 2-24 Scanner to Bioptic Communication......2-25 Scanner-Bioptic Packet Mode ......2-25 Chapter 3 - Input/Output Settings Good Read Indicators..........3-1 Beeper – Good Read ..........3-1 Beeper Volume – Good Read........ 3-1 Beeper Pitch –...
  • Page 5 Chapter 4 - Data Editing Prefix/Suffix Overview ..........4-1 To Add a Prefix or Suffix ........4-2 To Clear One or All Prefixes or Suffixes....4-2 To Add a Carriage Return Suffix to All Symbologies............4-3 Prefix Selections............ 4-3 Suffix Selections............ 4-4 Function Code Transmit ........
  • Page 6 All Symbologies ............6-2 Codabar Start/Stop Characters ......6-3 Codabar Check Character ........6-4 Codabar Concatenation ......... 6-5 Codabar Message Length ........6-6 Code 39 Start/Stop Characters ......6-7 Code 39 Check Character ........6-7 Code 39 Message Length........6-8 Code 39 Append ............
  • Page 7 UPC E0 Addenda ..........6-34 EAN/JAN 13 Check Digit........6-35 EAN/JAN 13 Addenda......... 6-36 EAN/JAN 13 Addenda Required ......6-36 EAN/JAN 13 Addenda Separator ......6-37 EAN/JAN 8 Check Digit........6-38 EAN/JAN 8 Addenda........... 6-39 EAN/JAN 8 Addenda Required ......6-39 EAN/JAN 8 Addenda Separator ......
  • Page 8 Resetting the Standard Product Defaults ....9-4 Menu Commands ............9-5 Chapter 10 - Product Specifications Youjie HH360 Product Specifications ......10-1 Standard Connector Pinouts........10-2 Chapter 11 - Maintenance and Troubleshooting Repairs ..............11-1 Maintenance .............. 11-1 Cleaning the Device..........11-1 Inspecting Cords and Connectors .......

  • Page 9: Chapter 1 - Getting Started

    Youjie HH360. Product specifications, dimensions, warranty, and customer sup- port information are also included. Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.

  • Page 10: Connecting With Keyboard Wedge

    3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. For additional USB programming and technical information, refer to the Honey- well “USB Application Note,” available at www.honeywellaidc.com. Connecting with Keyboard Wedge A scanner can be connected between the keyboard and PC as a “keyboard wedge,”...

  • Page 11: Connecting With Rs-232 Serial Port

    Connecting with RS-232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. only if power supply is included 3. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port.

  • Page 12: Menu Bar Code Security Settings

    Menu Bar Code Security Settings Honeywell scanners are programmed by scanning menu bar codes or by send- ing serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings.
  • Page 13 Serial Programming Commands starting on page 9-1 lists the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages). 1 - 5...
  • Page 14 1 - 6...

  • Page 15: Chapter 2 - Programming The Interface

    Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.

  • Page 16: Rs232 Serial Port

    RS232 Serial Port The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface bar code also programs a car- riage return (CR) and a line feed (LF) suffix, baud rate, and data format as indi- cated below.

  • Page 17: Usb Pc Or Macintosh Keyboard

    Scan the following code to program the scanner to emulate a regular RS232- based COM Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh comput- ers recognize the scanner as a USB CDC class device and automatically uses a class driver.

  • Page 18: Cts/Rts Emulation

    * ACK/NAK Mode Off Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit. Character RTS/CTS with timeout and 232 ACK/NAK are also enabled.

  • Page 19: Configuration

    ® Datalogic™ Magellan Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Datalogic Magellan bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Datalogic Magellan Bioptic Settings Note: If you are having unexpected results with this programming code, scan Resetting the Custom Defaults...
  • Page 20 Azeri (Latin) Belarus Belgium Bosnia Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) 2 - 6...
  • Page 21 Canada (French) Canada (Multilingual) China Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark 2 - 7...
  • Page 22 Dutch (Netherlands) Estonia Faroese Finland France Gaelic Germany Greek Greek (220 Latin) 2 - 8...
  • Page 23 Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary 2 - 9...
  • Page 24 Iceland Ireland Italian (142) Italy Japan ASCII Kazakh Korea Kyrgyz (Cyrillic) Latin America 2 - 10...
  • Page 25 Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) Norway Poland 2 - 11...
  • Page 26 Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) Serbia (Cyrillic) 2 - 12...
  • Page 27 Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) 2 - 13...
  • Page 28 Switzerland (German) Tatar Thailand Turkey F Turkey Q Ukrainian United Kingdom United Stated (Dvorak right) United States (Dvorak left) 2 - 14...

  • Page 29: Keyboard Mode Options

    United States (Dvorak) United States (International) Uzbek (Cyrillic) Vietnam Keyboard Mode Options ALT Mode If your bar code contains special characters from the extended ASCII chart for example, an e with an accent grave (è), you will use ALT Mode. (See Extended ASCII Characters on page A-6.) Note: Scan the ALT mode bar code after scanning the appropriate Keyboard Country code.

  • Page 30: Keyboard Style

    Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. Default = Regular. Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Shift Lock is used when you normally have the Shift Lock key on (not common to U.S.

  • Page 31: Keyboard Modifiers

    Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent). Emulate External Keyboard Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer. Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes. Control + X (Control + ASCII) Mode On: The scanner sends key combina- tions for ASCII control characters for values 00-1F.
  • Page 32 Default = Control + ASCII Off Windows Mode Control + X Mode On * Control + X Mode Off DOS Mode Control + X Mode Windows Mode Prefix/Suffix Off Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad.
  • Page 33 Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off Automatic Direct Connect Mode On * Automatic Direct Connect Mode Off 2 - 19...

  • Page 34: Rs232 Modifiers

    RS232 Modifiers RS-232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 38400. 4800 9600 19200 *38400 57,600 115,200...

  • Page 35: Rs-232 Word Length: Data Bits, Stop Bits, And Parity

    RS-232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an applica- tion requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.

  • Page 36: Rs-232 Handshaking

    RS-232 Handshaking RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. RTS/CTS Off: RTS/CTS is turned off so no data flow control is used, but RTS is still active. RTS/CTS Off, RTS Inactive: RTS/CTS is turned off so no data flow control is used and RTS is inactive.
  • Page 37 Flow Control, No Timeout Character-Based Flow Control, No Timeout Two-Direction Flow Control Flow Control with Timeout Character-Based Flow Control with Timeout CTS-Based Flow Control, No Timeout RTS On No RTS if CTS is On 2 - 23...

  • Page 38: Rs232 Timeout

    RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1- 65535 milliseconds) by scanning digits from the Programming Chart inside back...

  • Page 39: Scanner To Bioptic Communication

    ACK/NAK On * ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner. See "RS232 Modifiers"...
  • Page 40 2 - 26...

  • Page 41: Chapter 3 - Input/Output Settings

    Input/Output Settings Good Read Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = On. * On Beeper Volume –...

  • Page 42: Beeper Pitch - Good Read

    Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium Low (1600 Hz) * Medium (2700 Hz) High (4200 Hz) Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read.

  • Page 43: Beeper Pitch - Error

    Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = 100 Hz. * Razz (100 Hz) Medium (2000 Hz) High (4200 Hz) LED –...

  • Page 44: Number Of Beeps - Error

    scan the bar code below and then scan a digit (1-9) bar code and the Save bar code on the Programming Chart inside the back cover of this manual. Default = One. Number of Pulses Number of Beeps – Error The number of beeps and LED flashes emitted by the scanner for a bad read or error can be programmed from 1 - 9.

  • Page 45: Good Read Delay

    Good Read Delay This sets the minimum amount of time before the scanner can read another bar code. Default = No Delay. * No Delay Short Delay (500 ms) Medium Delay (1000 ms) Long Delay (1500 ms) User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from Programming Chart...

  • Page 46: Automatic Trigger

    When in serial mode, the scanner scans until a bar code has been read or until the deactivate command is sent. In serial mode, the scanner can also be set to turn itself off after a specified time has elapsed (see Read Time-Out, which fol- lows).

  • Page 47: Hands Free Time-Out

    for this capability. Once you have the aiming beam over the correct bar code, pull the trigger to read the code. Scan the Continuous Illumination Off bar code to turn off this feature. Continuous Illumination Mode On * Continuous Illumination Mode Off Hands Free Time-Out The Automatic Trigger and Presentation Modes are referred to as “hands free”...

  • Page 48: User-Specified Reread Delay

    Reread Delay only works when in automatic trigger mode or presentation mode (see page 3-6). Short (500 ms) * Medium (750 ms) Long (1000 ms) Extra Long (2000 ms) User-Specified Reread Delay If you want to set your own length for the reread delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the Pro- gramming Chart...

  • Page 49: Output Sequence Overview

    Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the Default Sequence symbol programs the scanner to the Universal values, shown below.
  • Page 50 Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 barcodes, but you want the image scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example. A - Code 39 B - Code 128 C - Code 93...

  • Page 51: Output Sequence Editor

    The breakdown of the command line is shown below: SEQBLK sequence editor start command code identifier for Code 39 0012 A - Code 39 sample length (11) plus CR suffix (1) = 12 start character match for Code 39, 41h = “A” termination string for first code code identifier for Code 128 0013...

  • Page 52: Multiple Symbols

    When the output sequence is Off, the barcode data is output to the host as the image scanner decodes it. Note: This selection is unavailable when the Multiple Symbols Selection is turned on. Required On/Not Required *Off Multiple Symbols When this programming selection is turned On, it allows you to read multiple symbols with a single pull of the scanner’s trigger.

  • Page 53: No Read

    No Read With No Read turned On, the scanner sends an “NR” to the host if you pull and release the trigger without reading a code (e.g., bad bar code). If No Read is turned Off, the “NR” will not be sent to the host. * Off If you want a different notation than “NR,”...
  • Page 54 3 - 14...

  • Page 55: Chapter 4 - Data Editing

    Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.

  • Page 56: To Add A Prefix Or Suffix

    To Add a Prefix or Suffix Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-3). Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in Appendix A) for the symbology to which you want to apply the prefix or suffix.

  • Page 57: To Add A Carriage Return Suffix To All Symbologies

    Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in Appendix A) for the symbology from which you want to clear the prefix or suffix. Step 3.

  • Page 58: Suffix Selections

    Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Transmit Alternate Extended ASCII Characters You may need to emulate special keyboard functions, such as up or down arrows, Alt/Make or Alt/Break commands, that are not supported in the Extended ASCII Character table. Refer to Alternate Extended ASCII Charac- ters (page 4-5) for a range of keyboard function keys and corresponding deci-...
  • Page 59 Alternate Extended ASCII Characters DEC HEX Keyboard Function DEC HEX Keyboard Function ↑ 128 80 152 98 up arrow ↓ 129 81 153 99 down arrow → 130 82 154 9A right arrow ← 131 83 155 9B left arrow 132 84 Insert 156 9C Numeric Keypad +...

  • Page 60: Function Code Transmit

    Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 7-2.

  • Page 61: Intercharacter Delay

    Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of steps in 5 millisecond incre- ments and the Save bar code using the Programming Chart inside the back cover of this manual.

  • Page 62: Interfunction Delay

    Next, scan the Character to Trigger Delay bar code, then the 2-digit hex value for a printable character to trigger the delay (see Lower ASCII Reference Table on page A-5). The range is 00-FF. Delay Length Character to Trigger Delay To remove this delay, scan the Delay Length bar code, and set the number of steps to 0.

  • Page 63: Intermessage Delay

    Intermessage Delay An intermessage delay of up to 495 milliseconds may be placed between each scan transmission. Scan the Intermessage Delay bar code below, then scan the number of steps in 5 millisecond increments and the Save bar code using Programming Chart inside the back cover of this manual.
  • Page 64 4 - 10...

  • Page 65: Chapter 5 - Data Formatting

    Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For exam- ple, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.

  • Page 66: Other Programming Selections

    Step 3. Terminal Type Refer to the Supported Terminals Chart (page 5-4) and locate the Ter- minal ID number for your PC. Scan three numeric bar codes on the Programming Chart inside back cover to program the scanner for your terminal ID (you must enter 3 digits).
  • Page 67 clearing your primary format. Scan the Terminal Type (refer to the Supported Terminals Chart on page 5-4), Code I.D. (refer to the Symbology Charts page A-1), and the bar code data length for the specific data format that you want to delete. All other formats remain unaffected. •...

  • Page 68: Interface / Terminal Id Table

    Interface / Terminal ID Table Interface Terminal ID PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop Serial RS232 TTL RS232 True Keyboard PS2 compatibles AT compatibles Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your input data string.
  • Page 69 F2 Example: Send a number of characters Send the first 10 characters from the bar code above, followed by a carriage return. Command string: F2100D F2 is the “Send a number of characters” command 10 is the number of characters to send 0D is the hex value for a CR The data is output as: 1234567890 F2 and F1 Example: Split characters into 2 lines...
  • Page 70 The data is output as: 1234567890AB Insert symbology name B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page A-1). Refer to the...

  • Page 71: Move Commands

    Move Commands Move the cursor forward a number of characters F5 Move the cursor ahead “nn” characters from current cursor position. Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead. F5 Example: Move the cursor forward and send the data Move the cursor forward 3 characters, then send the rest of the the bar code data from the bar code above.
  • Page 72 F8 Example: Send bar code data that starts after a particular character Search for the letter “D” in bar codes and send all the data that follows, including the “D.” Using the bar code above: Command string: F844F10D F8 is the “Search forward for a character” command 44 is the hex value for “D”...
  • Page 73 48 is the hex value for “H” F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: FGHIJ Search backward for a string B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s”...

  • Page 74: Miscellaneous Commands

    Search backward for a non-matching character E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non- “xx” character. Syntax = E7xx where xx stands for the search character’s hex value for the CP1252 character.
  • Page 75 Replace characters E4 Replaces up to 15 characters in the output message, without moving the cursor. Replacement continues until the E5 command is encountered. Syntax = E4nnxx ...zz where nn is the total count of of the number of characters in the list (characters to be replaced plus replacement characters);...
  • Page 76 Compare string B2 Compare the string in the input message to the string “s.” If the strings are equal, move the cursor forward past the end of the string. Syntax = B2nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string.
  • Page 77 F1 is the “Send all characters” command 0D is the hex value for a CR If this bar code is read, the next data format, if there is one, will be used on this data. If there is no other format, the format fails and the raw data is output as 1234AB.

  • Page 78: Data Format Editor

    Data Format Editor Enter Data Format * Default Data Format Clear One Data Format Clear All Data Formats Save Discard Data Formatter When Data Formatter is turned off, the bar code data is output to the host as read (including prefixes and suffixes). Choose one of the following options. 5 - 14...
  • Page 79 Default = Data Formatter On. * Data Formatter On, but Not Required Data Formatter Off When Data Formatter is required, all input data must conform to an edited for- mat or the scanner does not transmit the input data to the host device. Data Format On, Format Required 5 - 15...
  • Page 80 5 - 16...

  • Page 81: Introduction

    Symbologies Introduction This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults. • All Symbologies • GS1 DataBar Expanded • China Post Code • Interleaved 2 of 5 • Codabar • Label Code • Codablock F •...

  • Page 82: All Symbologies

    All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology.

  • Page 83: Codabar Start/Stop Characters

    EXAMPLE: Decode only those bar codes with a count of 9-20 characters. Min. length = 09 Max. length = 20 EXAMPLE: Decode only those bar codes with a count of 15 characters. Min. length = 15 Max. length = 15 For a value other than the minimum and maximum message length defaults, scan the bar codes included in the explanation of the symbology, then scan the digit value of the message length and Save bar codes on the...

  • Page 84: Codabar Check Character

    Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can pro- gram the scanner to read only Codabar bar codes with Modulo 16 check char- acters. Default = No Check Character. No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.

  • Page 85: Codabar Concatenation

    Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concat- enated into one with the “D” characters omitted. Character Start Stop...

  • Page 86: Codabar Message Length

    Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Minimum Message Length Maximum Message Length 6 - 6...

  • Page 87: Code 39 Start/Stop Characters

    Code 39 < Default All Code 39 Settings > Code 39 Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Code 39 Check Character...

  • Page 88: Code 39 Message Length

    When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check character, and will transmit this charac- ter at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit...
  • Page 89 are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 39 bar code that starts with a character other than a space. Default = Off. *Off Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies.

  • Page 90: Full Ascii

    Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.

  • Page 91: Check Digit

    ASCII Conversion Chart (Code Page 1252), page A-3, and scan the value and the Save bar code from the Programming Chart inside the back cover of this manual. The data characters should then appear properly. Code 39 Code Page Interleaved 2 of 5 <...

  • Page 92: Interleaved 2 Of 5 Message Length

    When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...

  • Page 93: Code 93 Message Length

    Code 93 < Default All Code 93 Settings > Code 93 * On Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 0-80.
  • Page 94 one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were created from the chart, ASCII Conversion Chart (Code Page 1252), page A-3, and scan the value and the Save bar code from the Programming Chart inside the back cover of this...

  • Page 95: Straight 2 Of 5 Industrial Message Length

    Straight 2 of 5 Industrial (three-bar start/stop) Straight 2 of 5 Industrial * On Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information.

  • Page 96: Straight 2 Of 5 Iata Message Length

    Straight 2 of 5 IATA (two-bar start/stop) Straight 2 of 5 IATA Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information.

  • Page 97: Matrix 2 Of 5 Message Length

    Matrix 2 of 5 Matrix 2 of 5 * Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 1-80.

  • Page 98: Check Digits Required

    Code 11 Code 11 * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit * Two Check Digits 6 - 18...

  • Page 99: Code 11 Message Length

    Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128 ...

  • Page 100: Code 128 Message Length

    recommendation to use Code 128 due to its high degree of security and its space-efficient design, 3) a variation of Code 128 that supports concatenation of neighboring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off.

  • Page 101: Code 128 Function Code Transmit

    Code 128 Code Page Code 128 Function Code Transmit By default, Code 128 function codes are not transmitted with Code 128 bar code data. However, if you wish to transmit Code 128 function codes with the bar code data, scan the Function Codes On bar code, below. Default = Off * Function Codes Off Function Codes On Telepen...

  • Page 102: Telepen Output

    Telepen * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2).

  • Page 103: Telepen Message Length

    Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60. Minimum Message Length Maximum Message Length 6 - 23...

  • Page 104: Upc A Check Digit

    UPC A UPC A * On UPC A Check Digit This selection allows you to specify whether the check digit should be transmit- ted at the end of the scanned data or not. Default = On. * On 6 - 24...

  • Page 105: Upc A Number System

    UPC A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data.

  • Page 106: Upc A Addenda Required

    UPC A Addenda Required When Addenda Required is set to on, the scanner will only read UPC A bar codes that have addenda. Default = Not Required. Required * Not Required UPC A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda.
  • Page 107 If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off. * Off Allow Concatenation Require Concatenation...
  • Page 108 Default = Don’t Require Coupon Code. * Don’t Require Coupon Code Require Coupon Code UPC-A Number System 5 Addenda Required This setting programs the scanner to require any combination of a coupon code, a 2 digit addenda, or a 5 digit addenda on UPC-A bar codes that begin with a “5.”...
  • Page 109 Default = Don’t Require Coupon Code/Addenda. * Don’t Require Coupon Code/ Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda Require Coupon Code Require Coupon Code or 2 Digit Addenda Require Coupon Code or 5 Digit Addenda Require Coupon Code, 2 Digit, or 5 Digit Addenda...
  • Page 110 Addenda Timeout You can set a time during which the scanner looks for a coupon code. If a coupon code is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A/ EAN-13 with Extended Coupon Code UPC-A Number System 4...

  • Page 111: Upc E0 And Upc E1

    UPC E UPC E0 and UPC E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number sys- tem, use the UPC E1 selection.

  • Page 112: Upc E0 And Upc E1 Expand

    UPC E0 and UPC E1 Expand UPC E Expand expands the UPC E code to the 12 digit, UPC A format. Default = Off. * Off UPC E0 and UPC E1 Addenda Required When Addenda Required is set to on, the scanner will only read UPC E bar codes that have addenda.

  • Page 113: Upc E0 And Upc E1 Addenda Separator

    UPC E0 and UPC E1 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On UPC E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not.

  • Page 114: Upc E0 Number System

    UPC E0 Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On UPC E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC E data.

  • Page 115: Ean/Jan 13 Check Digit

    EAN/JAN 13 EAN/JAN 13 * On EAN/JAN 13 Check Digit This selection allows you to specify whether the check digit should be transmit- ted at the end of the scanned data or not. Default = On. * On 6 - 35...

  • Page 116: Ean/Jan 13 Addenda

    EAN/JAN 13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 13 Addenda Required When Addenda Required is set to on, the scanner will only read EAN/JAN 13...

  • Page 117: Ean/Jan 13 Addenda Separator

    EAN/JAN 13 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon Code on page 6-26.

  • Page 118: Ean/Jan 8 Check Digit

    EAN/JAN 8 * On EAN/JAN 8 Check Digit This selection allows you to specify whether the check digit should be transmit- ted at the end of the scanned data or not. Default = On. * On 6 - 38...

  • Page 119: Ean/Jan 8 Addenda

    EAN/JAN 8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda * 5 Digit Addenda Off EAN/JAN 8 Addenda Required...

  • Page 120: Ean/Jan 8 Addenda Separator

    EAN/JAN 8 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On * Off MSI Check Character Different types of check characters are used with MSI bar codes.

  • Page 121: Msi Message Length

    When Check Character is set to Validate and Transmit, the scanner will only read MSI bar codes printed with the specified type check character, and will transmit this character at the end of the scanned data. When Check Character is set to Validate, but Don’t Transmit, the unit will only read MSI bar codes printed with the specified type check character, but will not transmit the check character with the scanned data.

  • Page 122: Plessey Message Length

    Plessey Code * Off Plessey Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length GS1 DataBar Omnidirectional...
  • Page 123 GS1 DataBar Omnidirectional * On GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited * On GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > 6 - 43...

  • Page 124: Gs1 Databar Expanded Message Length

    GS1 DataBar Expanded * On GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74. Minimum Message Length Maximum Message Length China Post Code...
  • Page 125 China Post Code * Off China Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length 6 - 45...

  • Page 126: Korea Post Message Length

    Korea Post Code Korea Post Code * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 2-80.

  • Page 127: Codablock F Message Length

    Codablock F Codablock F * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048. Minimum Message Length Maximum Message Length 6 - 47...

  • Page 128: Code 49 Message Length

    Code 49 Code 49 * Off Code 49 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description on page 6-2 for additional information. Minimum and Maximum lengths = 1-81. Minimum Default = 1, Maximum Default = 81. Minimum Message Length Maximum Message Length 6 - 48...
  • Page 129 Trioptic Code Trioptic Code is used for labeling magnetic storage media. GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and GS1-128 DataBar and GS1Composites.
  • Page 130 Label Code The standard Label Code is used in library situations. Default = Off. * Off 6 - 50...

  • Page 131: Chapter 7 - Interface Keys

    Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the scanner. Refer to Windows Mode Control + X Mode On (page 2-18) to enable Control + ASCII mode.

  • Page 132: Supported Interface Keys

    Supported Interface Keys IBM AT/XT and PS/2 Compatibles, WYSE PC/AT ASCII Supported Keys Reserved Enter (KP) Cap Lock ALT make ALT break CTRL make CTRL break CR/Enter Reserved Reserved Delete CR/Enter Insert Escape Home Print Back Space Back Tab * IBM 3191/92, 3471/72, 3196/97, 3476/77, Telex (all models) 7 - 2...
  • Page 133 Supported Interface Keys Apple Mac/iMac ASCII Supported Keys Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make APPLE break RETURN Ins Help Home Prnt Scrn BACKSPACE LSHIFT TAB BACKSPACE 7 - 3...
  • Page 134 7 - 4...

  • Page 135: Chapter 8 - Utilities

    Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts (page A-1) for the single character code that identifies each symbology.) This action first clears all cur- rent prefixes, then programs a Code I.D.

  • Page 136: Resetting The Standard Product Defaults

    Resetting the Standard Product Defaults This selection erases all your settings and resets the scanner to the original factory defaults. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default set- tings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults.

  • Page 137: Chapter 9 - Serial Programming Commands

    Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will pro- gram the scanner. For complete descriptions and examples of each serial pro- gramming command, refer to the corresponding programming bar code in this manual.

  • Page 138: Query Commands

    Query Commands Several special characters can be used to query the device about its settings. What is the default value for the setting(s). What is the device’s current value for the setting(s). What is the range of possible values for the setting(s). (The de- vice’s response uses a dash (-) to indicate a continuous range of values.

  • Page 139: Examples Of Query Commands

    Examples of Query Commands In the following examples, a bracketed notation [ ] depicts a non-displayable response. Example: Example #1:What is the range of possible values for Codabar Coding Enable? Enter: cbrena*. Response: CBRENA0-1[ACK] This response indicates that Codabar Coding Enable (CBRENA) has a range of values from 0 to 1 (off and on).

  • Page 140: Trigger Commands

    Trigger Commands You can activate and deactivate the scanner with serial trigger commands. First, the scanner must be put in Manual/Serial Trigger Mode either by scanning the Manual/Serial Trigger Mode bar code (page 3-5), or by sending the Manual/ Serial Menu Command (page 9-12).

  • Page 141: Menu Commands

    Menu Commands Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Product Default Settings Setting Custom Set Custom Defaults MNUCDF Defaults Resetting the Custom Activate Custom DEFALT Defaults Defaults Programming the Interface Plug and Play Codes Keyboard Wedge: IBM PAP_AT PC AT and...
  • Page 142 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Arabic KBDCTY91 Azeri (Cyrillic) KBDCTY81 Azeri (Latin) KBDCTY80 Belarus KBDCTY82 Belgium KBDCTY1 Bosnia KBDCTY33 Brazil KBDCTY16 Brazil (MS) KBDCTY59 Bulgaria (Cyrillic) KBDCTY52 Bulgaria (Latin) KBDCTY53 Canada (French KBDCTY54 legacy) Canada (French)
  • Page 143 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Greek (319 Latin) KBDCTY65 Greek (319) KBDCTY62 Greek (Latin) KBDCTY63 Greek (MS) KBDCTY66 Greek (Polytonic) KBDCTY60 Hebrew KBDCTY12 Hungarian (101 key) KBDCTY50 Hungary KBDCTY19 Iceland KBDCTY75 2-10 Ireland KBDCTY73 2-10...
  • Page 144 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Russian (MS) KBDCTY67 2-12 Russian (Typewriter) KBDCTY68 2-12 KBDCTY21 2-12 Serbia (Cyrillic) KBDCTY37 2-12 Serbia (Latin) KBDCTY36 2-13 Slovakia KBDCTY22 2-13 Slovakia (QWERTY) KBDCTY49 2-13 Slovakia (QWERTZ) KBDCTY48 2-13 Slovenia...
  • Page 145 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Keyboard Style *Regular KBDALT7 2-16 Caps Lock KBDSTY1 2-16 Shift Lock KBDSTY2 2-16 Automatic Caps Lock KBDSTY6 2-16 Autocaps via KBDSTY7 2-16 NumLock Emulate External KBDSTY5 2-17 Keyboard Keyboard Modifiers Windows Mode...
  • Page 146 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Word Length: Data 7 Data, 1 Stop, Parity 2-21 232WRD3 Bits, Stop Bits, and Even Parity 7 Data, 1 Stop, Parity 232WRD6 2-21 7 Data, 2 Stop, Parity 232WRD4 2-21 Even...
  • Page 147 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry *ACK/NAK Off 232ACK0 2-25 ACK/NAK On 232ACK1 2-25 Scanner-Bioptic *Packet Mode Off 232PKT0 2-25 Packet Mode Packet Mode On 232PKT1 2-25 Output Selections Beeper - Good Read BEPBEP0 BEPBEP1 Beeper Volume - Good...
  • Page 148 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry User-Specified Good Range 0 - 30,000 ms DLYGRD##### Read Delay Trigger Mode *Manual/Serial Trigger TRGMOD0 Read Time-Out (0 - TRGSTO#### 300,000 ms) *30,000 Automatic Trigger TRGMOD1 Continuous ILLAON1 Illumination On *Continuous...
  • Page 149 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Prefix Add Prefix PREBK2## Clear One Prefix PRECL2 Clear All Prefixes PRECA2 Suffix Add Suffix SUFBK2## Clear One Suffix SUFCL2 Clear All Suffixes SUFCA2 Transmit Alternative Transmit Alternate KBDEXT0 Extended ASCII Extended ASCII...
  • Page 150 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Codabar Default All Codabar CBRDFT Settings Codabar CBRENA0 CBRENA1 Codabar Start/Stop *Don’t Transmit CBRSSX0 Char. Transmit CBRSSX1 Codabar Check Char. *No Check Char. CBRCK20 Validate, But Don’t CBRCK21 Transmit Validate, and Transmit...
  • Page 151 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Code 32 *Off C39B320 Pharmaceutical C39B321 (PARAF) Code 39 Full ASCII *Off C39ASC0 6-10 C39ASC1 6-10 Interleaved 2 of 5 Default All Interleaved I25DFT 6-11 2 of 5 Settings Interleaved 2 of 5 I25ENA0 6-11...
  • Page 152 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Straight 2 of 5 IATA *Off A25ENA0 6-16 A25ENA1 6-16 Straight 2 of 5 IATA Minimum (1 - 48) *4 A25MIN## 6-16 Message Length Maximum (1 - 48) *48 A25MAX## 6-16 Matrix 2 of 5...
  • Page 153 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Telepen *Off TELENA0 6-22 TELENA1 6-22 Telepen Output *AIM Telepen Output TELOLD0 6-22 Original Telepen TELOLD1 6-22 Output Telepen Message Minimum (1 - 60) *1 TELMIN## 6-23 Length Maximum (1 - 60) *60 TELMAX##...
  • Page 154 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry UPC-A Number * Don’t Require ARQSY50 6-29 System 5 Addenda Coupon Code/ Required Addenda Require 2 Digit ARQSY51 6-29 Addenda Require 5 Digit ARQSY52 6-29 Addenda Require 2 or 5 Digit ARQSY53 6-29 Addenda...
  • Page 155 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry UPC E 2 Digit *Off UPEAD20 6-34 Addenda UPEAD21 6-34 UPC E 5 Digit *Off UPEAD50 6-34 Addenda UPEAD51 6-34 UPC E Addenda *Not Required UPEARQ0 6-32 Required Required UPEARQ1...
  • Page 156 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry EAN/JAN 8 5 Digit *Off EA8AD50 6-39 Addenda EA8AD51 6-39 EAN/JAN 8 Addenda *Not Required EA8ARQ0 6-32 Required Required EA8ARQ1 6-32 EAN/JAN 8 Addenda EA8ADS0 6-40 Separator EA8ADS1 6-40 Default All MSI...
  • Page 157 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry GS1 DataBar Default All GS1 RSEDFT 6-44 Expanded DataBar Expanded Settings GS1 DataBar RSEENA0 6-44 Expanded RSEENA1 6-44 GS1 DataBar Minimum (4 - 74) *4 RSEMIN## 6-44 Expanded Msg.
  • Page 158 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry GS1 Emulation EANEMU2 6-49 GS1 Emulation GS1-128 Emulation EANEMU1 6-49 *GS1 Emulation Off EANEMU0 6-49 Label Code *Off LBLENA0 6-50 LBLENA1 6-50 9 - 22...

  • Page 159: Chapter 10 - Product Specifications

    Product Specifications Youjie HH360 Product Specifications Parameter Specification Mechanical Height 6.1 inches (15.5 cm) Length 5.0 inches (12.6 cm) Width 2.8 inches (7.3 cm) Weight 4.7 ounces (135 g) Electrical LED source 630 nm visible red LED Input Voltage 4.5-5.5VDC at imager Operating Power 180mA @ 5V Standby Power...

  • Page 160: Standard Connector Pinouts

    Standard Connector Pinouts Keyboard Wedge 10 Pin RJ41 Modular Plug - connects to the scanner handle 1 Cable shield 2 Cable select 3 Supply ground 4 Terminal data 5 Terminal clock 6 Keyboard clock 7 +5V power 8 Keyboard data Serial Output 10 Pin RJ41 Modular Plug - connects to the scanner handle 1 Cable shield...
  • Page 161 Required Safety Label Locations Light Source Model Number Compliance Label Label Location 10 - 3...
  • Page 162 10 - 4...

  • Page 163: Chapter 11 - Maintenance And Troubleshooting

    Inspect the scanner’s interface cable and connector for wear or other signs of damage. A badly worn cable or damaged connector may interfere with scanner operation. Contact your Honeywell distributor for information about cable replacement. Cable replacement instructions are on page 11-2.

  • Page 164: Replacing The Interface Cable

    The interface cable is designed to be field replace- able. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.
  • Page 165 Is the scanner having trouble reading your symbols? If the scanner isn’t reading symbols well, check that the symbols: • Aren’t smeared, rough, scratched, or exhibiting voids. • Aren’t coated with frost or water droplets on the surface. • Are enabled in the scanner or in the decoder to which the scanner connects. Is the bar code displayed but not entered? The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example).
  • Page 166 11 - 4...

  • Page 167: Chapter 12 - Technical Assistance

    Technical Assistance Contact information for technical support, product service, and repair can be found at www.youjieaidc.com. Limited Warranty Youjie warrants its products to be free from defects in materials and workman- ship and to conform to Youjie’s published specifications applicable to the prod- ucts purchased at the time of shipment.
  • Page 168 All provisions of this Limited Warranty are separate and severable, which means that if any provision is held invalid and unenforceable, such determina- tion shall not affect the validity of enforceability of the other provisions hereof. Use of any peripherals not provided by the manufacturer may result in damage not covered by this warranty.

  • Page 169: Symbology Charts

    Symbologies, 99) entry. Refer toData Editing beginning on page 4-1 and Data Formatting beginning on page 5-1 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible Symbology modifiers All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical <...
  • Page 170 0, 1 0, 1, 2, 3, 8, 9, A, B, C UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C A - 2...

  • Page 171: Postal Symbologies

    Postal Symbologies Honeywell Possible Symbology modifiers All Symbologies Australian Post British Post Canadian Post China Post InfoMail Intelligent Mail Bar Code Japanese Post KIX (Netherlands) Post Korea Post Planet Code Postal-4i Postnet ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 dif- ferent ways, as shown below.
  • Page 172 CTRL+ B Bold Caps Lock Txt: [STX] CTRL+ C Copy ALT Make Txt: [EXT] CTRL+ D Bookmark ALT Break Txt: [EOT] CTRL+ E Center CTRL Make Txt: [ENQ] CTRL+ F Find CTRL Break Txt: [ACK] CTRL+ G Enter / Ret Txt: [BEL] CTRL+ H History...

  • Page 173: Lower Ascii Reference Table

    Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. Printable Characters DEC HEX Character DEC HEX Character DEC HEX Character " & < > ⌂ A - 5...
  • Page 174 Extended ASCII Characters PS2 Scan DEC HEX CP 1252 ASCII Alternate Extended Code ↑ € Ç 0x48 up arrow ↓ ü 0x50 down arrow → ‚ é 0x4B right arrow ← ƒ â 0x4D left arrow „ ä Insert 0x52 …...
  • Page 175 Extended ASCII Characters (Continued) PS2 Scan DEC HEX CP 1252 ASCII Alternate Extended Code ¥ Ñ Print Screen ¦ ª 0x0F § º Shift Tab 0x8F ¨ ¿ Enter 0x1C © ⌐ 0x01 ª ¬ Alt Make 0x36 « ½ Alt Break 0xB6 ¬...
  • Page 176 Extended ASCII Characters (Continued) PS2 Scan DEC HEX CP 1252 ASCII Alternate Extended Code Ì ╠ Í ═ Î ╬ Ï ╧ Ð ╨ Ñ ╤ Ò ╥ Ó ╙ Ô ╘ Õ ╒ Ö ╓ × ╫ Ø ╪ Ù...

  • Page 177: Iso 2022/Iso 646 Character Replacements

    United States (standard ASCII) ISO/IEC 646-IRV Automatic National Character Replacement ISO/IEC 2022 2 (default) Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. A - 9...
  • Page 178 United States ISO/IEC 646-06 Canada ISO /IEC 646-121 Canada ISO /IEC 646-122 Japan ISO/IEC 646-14 China ISO/IEC 646-57 Great Britain (UK) ISO /IEC 646-04 France ISO /IEC 646-69 Germany ISO/IEC646-21 Switzerland ISO /IEC 646-CH Sweden / Finland (extended Annex C) ISO/IEC 646-11 Ireland ISO /IEC 646-207...
  • Page 179 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ⎯ ¥ ⎯ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...
  • Page 180 Unicode Key Maps 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
  • Page 181 Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 1234567890 Code 128 Code 128 EAN 13 9 780330 290951 EAN 8 3210 5 UPC-E 456123...
  • Page 182 Sample Symbols Code 39 Codabar BC321 Code 93 A13579B Straight 2 of 5 Industrial 123456-9$ 123456 Matrix 2 of 5 6543210 GS1 DataBar (01)00123456789012...
  • Page 183 Programming Chart...
  • Page 184 Programming Chart Save Discard Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
  • Page 186 YJ-HH360-UG Rev (a) 07/15...

Table of Contents