Related Manuals for Haier HTW70-M1217
Summary of Contents for Haier HTW70-M1217
- Page 1 TWIN TUB WASHING MACHINE USER MANUAL MODEL HTW70-M1217 HTW90-M1217 HTW110-M1217 HTW130-M1217 Please read this manual carefully before operating your washing machine and retain it for future reference.
-
Page 2: Table Of Contents
CONTENTS Product Overview Safety precautions Installation and adjustment Before Washing Laundry Guidelines Operation Cleaning and Maintenance Troubleshooting Packing list Specifications... -
Page 3: Product Overview
Product Overview Wash selector (HTW70- M1217/HTW90-M1217) Wash selector Drain selector (HTW110-M1217/HTW130-M1217) Wash timer Water inlet Spin Tub Cover Water inlet selector Safety Cover Control panel Overflow filter Spin tub Lint filter (Installed by user) Wash Tub Cover Wash tub Cabinet Drain hose Base frame (Installed by user) -
Page 4: Safety Precautions
Safety precautions Contents marked with this symbol are Ensure the plug is removed and the taps related to the safety information of the turned off in the following cases. Power products. Please operate in accordance to failure, cleaning, moving, installation and the contents of this manual, to prevent when not in use. - Page 5 Safety precautions Do not attempt to put your hand into the washing machine Do not leave hot or heavy items on cover or control panel as this may cause or modify the appliance yourself. damage to the washer or make the washer unsafe to operate.
-
Page 6: Installation And Adjustment
Installation and adjustment Install the lint filter into the filter case as shown. Please ensure the lint filter is in place, otherwise the lint filter may detach from the filter case when the washing is undergoing and impact on the washing performance. - Page 7 Installation and adjustment Install the water inlet hose; Select the water level control panel. Set the water level according the laundries loaded. Note: The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
-
Page 8: Before Washing
Before Washing Preparation before washing 1. Connect the jointer of the water inlet hose to the water faucet. Turn on the water faucet. 2. The washing machine must be properly grounded. Then plug in the power cord to the power socket. Do not ground the washing machine to a gas pipe, water pipe or telephone line. -
Page 9: Laundry Guidelines
Laundry Guidelines laundry that could be loaded into the appliance. actual capacity. laundries loaded to avoid the water splashing. powder. Usage of the detergent : bleach ・ bleach washing tub. ・ Avoid using bleach on the laundries directly. Bleach causes discoloration on clothes. - Page 10 Wash timer Wash selector Wash selector Drain selector Spin timer (HTW70-M1217) (HTW110-M1217) (HTW110-M1217) (If to set less than 1 （ If you wish to (HTW90-M1217) (HTW130-M1217) (HTW130-M1217) set it for less than min, in order to (Intensity can (Intensity can...
-
Page 11: Operation
Operation 1. Spread the laundries into the spinning tub evenly. a.Put and push the inner cover properly no matter how much laundries loaded. Push Inner cover Push No Inner cover Proper The laundry Proper is slanted. b.Close the spin tub cover and safety cover. c.Set the spinning time by rotating the spin timer. - Page 12 Operation Rinsing Overflow-Rinse 1.Unload the laundries from spin tub and load into wash tub, turn the water inlet selector to WASH. Set the washing time by rotating the wash timer according to laundries loaded. 2.Adjust the water level according to laundries loaded, turn on the water tap until the cycle finished.
- Page 13 Operation Final Spin 1.Same as the first spin operation, loaded the wet laundries and put the inner spin cover inside the spin tub properly. 2.Close the spin tub cover and safety cover. 3.Set the spin time by rotating the spin timer according to the wet laundries loaded. During the spinning process, there may be noise caused by wet laundries not loaded properly.
-
Page 14: Cleaning And Maintenance
Cleaning and Maintenance Remove the power plug before carry out any cleaning and maintenance. Clean the lint filter and overflow filter after each wash cycle, otherwise it may influence your next use. Cleaning the lint filter Lint filter must be used during washing. Clean the line filter after using. - Page 15 Cleaning and Maintenance Cleaning the overflow filter Too much lint residual in the overflow filter will affect the performance, please clean the filter regularly. 1.Remove the overflow filter by pressing the side handle and pull it out. 2.Clean the filter with running water. 3.When cleaning is completed, press the side handle and put the filter back to the filter case.
-
Page 16: Troubleshooting
Troubleshooting Many occurring problems could be solved by yourself without specific expertise. Please check all the shown possibilities and the solution below before contact the customer care team. Please switch off the machine and remove the power plug before troubleshooting. Phenomena The reason Is there a power failure? -
Page 17: Packing List
Packing list Name Quantity Twin tub washing machine Water intake hose User manual Inner Cover Lint filter Drain hose Hose clamp Four Mounting foot... -
Page 18: Specifications
Specifications HTW90-M1217 HTW70-M1217 220-240V~ 220-240V~ 441 939 HTW110-M1217 HTW130-M1217 220-240V~ 220-240V~ 890 542 030 859 504 999...