GE JGSP42SETSS Installation Instructions Manual
30” gas self-clean slide-in range
Hide thumbs
Also See for JGSP42SETSS:
- Owner's manual (136 pages) ,
- Dimensions and installation information (2 pages) ,
- Use and care manual (136 pages)
Table of Contents
Quick Links
Installation Instructions
30" Gas Self-Clean Slide-In Range
Questions?
Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca
BefoRe You BeGIn
Read these instructions completely and carefully.
–
IMPoRTAnT
•
Save these instructions
for local inspector's use.
–
IMPoRTAnT
•
Observe all governing
codes and ordinances.
•
note to Installer – Leave these
instructions with appliance after installation
is complete.
•
note to Consumer – Keep these
instructions for future reference.
•
note to Servicer – The electrical diagram
is in an envelope attached to the back
of the range.
WARnInG:
fire and explosion Hazard:
If the information in the manual is not followed exactly, a fire or explosion may result causing
property damage, personal injury, or death.
•
If you smell gas:
– Open windows
– Don't touch electrical switches.
– Extinguish any open flame.
– Immediately call your gas supplier.
•
Do not store or use combustible materials, gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
•
Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
•
Remove all packing material and literature from oven before connecting gas and electrical
supply to the range.
In THe CoMMonWeALTH of MASSACHuSeTTS:
•
This product must be installed by a licensed plumber or gas fitter.
•
When using ball-type gas shut-off valves, they shall be the T-handle type.
•
A flexible gas connector, when used, must not exceed 3 feet (91.4 cm).
•
Proper installation is the responsibility
of the installer. Product failure due to
improper installation is not covered under
the Warranty.
•
Installation of the range must conform
with local codes or, in the absence of local
codes, with the National Fuel Gas, ANSI
Z223.1/NFPA 54, latest edition. In Canada,
installation must conform with the current
Natural Gas Installation Code, CAN/CSA-
B149.1 or the current Propane Installation
Code, CAN/CSA-B149.2, and with local
codes where applicable. This range has
been design-certified by Underwriter's
Laboratories for use in the United States
and Canada.
WARnInG:
electrical Shock Hazard:
This appliance must be properly grounded in accordance with local codes or, in the absence of local codes,
in accordance with the National Electrical Code (ANSI/NFPA 70, latest edition). In Canada, electrical
grounding must be in accordance with the current CSA C22.1 Canadian Electrical Code Part 1 and/or local
codes. See the Electrical Requirements section.
PReSSuRe TeST InfoRMATIon
The maximum allowable supply pressure for the regulator is 14" W.C. The minimum supply
pressure needed to check the regulator setting is 7" W.C. for natural gas and 10" W.C. for LP
gas.
WARnInG:
The range and its individual shut-off valve must be
disconnected from the gas supply piping system during any pressure testing of the gas
supply system at test pressures of more than 1/2 psig (pounds per square inch gauge).
The range must be isolated from the gas supply piping system by closing its individual
shut-off valve during any pressure testing of the gas supply system at test pressures
equal to or greater than 1/2 psig. noTe: 1/2 psig = 13.855" w.c.
MATeRIALS You MAY need
CSA-Approved Flexible Gas Line 3/8" Min. ID, 1/2" NPT Connection
Shut-Off Valve
Joint Sealant
Pipe Fittings
TooLS You WILL need
Drill with 1/8" Bit
Level
Safety Glasses
Tape Measure
Adjustable Wrench
Pliers
Pipe Wrench
1/4" Nut Driver
If you did not receive an anti-tip
bracket with your purchase, call
1.800.626.8774 to receive one
at no cost. (In Canada, call
1.800.561.3344.) For installation
instructions of the bracket, visit: www.
Anti-Tip Bracket
GEAppliances.com.
Kit Included
(In Canada, www.GEAppliances.ca.)
Phillips-Head Screwdriver
Flat-Blade Screwdriver
Table of Contents
Related Manuals for GE JGSP42SETSS
Summary of Contents for GE JGSP42SETSS
-
Page 1: Installation Instructions
Installation Instructions 30” Gas Self-Clean Slide-In Range Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca BefoRe You BeGIn • Proper installation is the responsibility Read these instructions completely and carefully. - Page 2 R EMOVE PACKAGING MATERIAls Failure to remove packaging materials could result in damage to the appliance. Remove all packing parts from oven, racks and drawer. Also, remove protective film and labels on the door, cooktop and backguard. However, do not remove protective channel from sides of glass cooktop, if applicable, until later in installation. Move Range Indoors in Front of Cabinet Opening: Do not use hand trucks when moving the unpacked range, as damage to the cooktop may occur. Protect the Kitchen Floor: Flatten and place a piece of the shipping carton in front of the installation location to protect the flooring. PREPARE THE OPENING (FOR INdOOR usE ONly) If the countertop area is not flat, excess tension may be applied to the cooktop causing damage and voiding the warranty. Make sure the wall covering, countertop, flooring and cabinets around the range can withstand the heat (up to 200°F [93.3°C]) generated by the range. A. A llow 30” (76.2 cm) minimum clearance between burners and bottom of unprotected wood or metal cabinet, or allow a 24” (61 cm) minimum when bottom of wood or metal cabinet is protected by no less than 1/4” (6.4 mm) thick flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015” [.38 mm] thick), .015” (.38 mm) thick stainless steel, .025” (0.64 mm) aluminum or .020”...
-
Page 3: Electrical Requirements
31-10675-1 31-10737-1 = French version 31-10738-1 = Spanish version 09-2009 GE 5 ELECTRiCAL REqUiREmEnTS warNING: IMPOrtaNt:This appliance must be electrically grounded in accordance with local codes or, in the absence of local codes, with the national Electrical Code, AnSi/nFPA 70 or Canadian Electrical Code, CSA C22.1. -
Page 4: A Nti-Tip Device Installation
M AKE GAS CONNECTIONS WARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury. Always use new flexible connectors when installing a gas appliance. WARNING: Do not use a flame to check for gas leaks. Use liquid leak detector at all joints and connections to check for leaks in the system. A. I nstall a manual shut-off valve in the gas supply line in an easily accessible location. B. K now how and where to shut off the gas supply to the range. C. S hut off gas supply before removing an old range. -
Page 5: Cooktop Burners
R EPLACING THE OVEN DOOR NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. A. L ift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle. B. W ith the door at the same angle as the removal position (approximately 1”–2” [2.5 cm–5.1 cm] from the closed position), seat the notch of the hinge arm into the bottom edge of the hinge slot. The notch of the hinge arm must be fully seated into the bottom of the slot. C. F ully open the door. If the door will not fully open, the indentation is not seated correctly in the bottom edge of the slot. D. P ush the hinge locks up against the front frame of the oven cavity, to the locked position. E. C lose the oven door. Bottom edge of slot Hinge in locked position Notch of hinge securely fitted into bottom of hinge slot REPLACE THE STORAGE DRAWER A. P lace the drawer rail on the guides. Push the drawer in until it stops. - Page 6 The burner flames should not flutter or blow away from the burner. The cover inner cone of the flame should be between 1/2” and 3/4” (12.7 mm and 19.1 mm) long. If the burner flames are yellow in color or not the proper length, call GE Service. burners should be checked frequently. WArnInG: please use caution. burns could result.
-
Page 7: Adjust The Air Shutter
11 BAKE AND BROIL BuRNERs chEcKINg thE OvEN BuRNERs to check the bake burner flames with the oven door in the closed position: A. O pen the door and remove it. (Optional—see Step 4.) B. Remove the oven racks. c. R emove the oven bottom. Lift the oven bottom up at the rear and pull forward. D. R emove the four screws holding the burner baffle (flame spreader) to the burner box. -
Page 8: Operation Checklist
12 F INAL INSTALLATION CHECKLIST • C hecktomakesurethecircuitbreakerisclosed(RESET)orthecircuitfusesarereplaced. • B esurepowerisinservicetothebuilding. • C heckthatallpackingmaterialsandtapehavebeenremoved.Thiswillincludetapeonmetal panelundercontrolknobs(ifapplicable),adhesivetape,wireties,cardboardandprotectiveplastic. Failuretoremovethesematerialscouldresultindamagetotheapplianceoncetheappliancehas beenturnedonandsurfaceshaveheated. • C heckthatthedooranddrawerareparalleltoeachotherandthatbothoperatesmoothly.Ifthey donot,repeatsteps4and9. • C hecktomakesurethattherearlevelinglegisfullyinsertedintotheanti-tipbracketandthat thebracketissecurelyinstalled. OpErATION CHECKLIST • C heckthattheovencontroloperatesproperly.Iftheovencontroldoesnotoperateproperly, recheckthewiringconnections. • B esureallrangecontrolsareintheOFFpositionbeforeleavingtherange.