1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. Catalyst 2955 Series
  6. Installation notes

Cisco Catalyst 2955 Installation Notes

Switch din rail clip
Hide thumbs Also See for Catalyst 2955:
Table of Contents

Quick Links

See also: Configuration Manual
Catalyst 2955 Switch DIN Rail Clip

Installation Notes

These installation notes provide updated installation and removal instructions for the DIN rail clip on
the Catalyst 2955 switch.
For installation, software, or troubleshooting instructions for your switch, refer to the documentation on
Note
Cisco.com for the Catalyst 2955 switch.
Contents
This document contains these major sections:
•
•
•
•
•
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2003 Cisco Systems, Inc. All rights reserved.
Overview, page 2
Table of Contents
loading

Related Manuals for Cisco Catalyst 2955

Summary of Contents for Cisco Catalyst 2955

  • Page 1: Table Of Contents

    Removing the Switch from a DIN Rail, page 6 • • Related Documentation, page 7 Obtaining Technical Assistance, page 9 • Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 2003 Cisco Systems, Inc. All rights reserved.

  • Page 2: Overview

    Overview Overview The rear panel of the Catalyst 2955 switch has a DIN rail mounting clip assembly, as shown in Figure 1 DIN Rail Clip Parallel Mounting Configuration Catalyst 2955 switch rear panel DIN rail clip assembly Mounting the Switch on a DIN Rail You can mount the Catalyst 2955 switch on a DIN rail in a parallel or a face-down configuration.
  • Page 3 The enclosure must meet IP 54 or NEMA type 4 minimum enclosure rating standards. Caution To prevent the switch from overheating, there must be a minimum of 3 inches between any other device and the top, bottom, or sides of the switch.
  • Page 4 Mounting the Switch on a DIN Rail To attach the switch to a DIN rail, follow the procedures in this section. Position the rear panel of the switch directly in front of the DIN rail, making sure that the top of the DIN Step 1...
  • Page 5 Mounting the Switch on a DIN Rail in a Face-Down Configuration DIN rail clip DIN rail Rotate the switch down toward the DIN rail until the release tab on the rear panel clicks. Step 2 Step 3 Lift lightly on the bottom of the switch to ensure that it is firmly locked in place.

  • Page 6: Removing The Switch From A Din Rail

    To remove the switch from a DIN rail, follow these steps: Step 1 Ensure that power is removed from the switch, and disconnect all cables and connectors from the front panel of the switch. Push down on the top of the DIN rail clip release tab with your finger. As the clip releases, lift the bottom...

  • Page 7: Related Documentation

    Figure 6 Switch Removal in a Face-Down Mounting Configuration DIN rail clip DIN rail Related Documentation These documents provide complete information about the Catalyst 2955 switches and are available from this URL: http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2950/index.htm OL-5262-01 DIN rail clip release tab Catalyst 2955 Switch DIN Rail Clip Installation Notes...

  • Page 8: Obtaining Documentation

    You can order printed copies of documents with a DOC-xxxxxx= number from the Cisco.com sites and from the telephone numbers listed in the • Release Notes for the Catalyst 2955 Switch (not orderable but is available on Cisco.com) Note Switch requirements and procedures for initial configurations and software upgrades tend to change and therefore appear only in the release notes.

  • Page 9: Documentation Feedback

    The Cisco Technical Assistance Center (TAC) is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two levels of support are available: the Cisco TAC Web Site and the Cisco TAC Escalation Center. OL-5262-01 Obtaining Technical Assistance Catalyst 2955 Switch DIN Rail Clip Installation Notes...
  • Page 10 NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. Catalyst 2955 Switch DIN Rail Clip Installation Notes OL-5262-01...
  • Page 11 Cisco device. CCVP, the Cisco logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco...
  • Page 12 Catalyst 2955 Switch DIN Rail Clip Installation Notes OL-5262-01...

Table of Contents