Fujitsu PRIMERGY RX1330 M4 Upgrade And Maintenance Manual
  1. Manuals
  2. Brands
  3. Fujitsu Manuals
  4. Server
  5. PRIMERGY RX1330 M4
  6. Upgrade and maintenance manual

Fujitsu PRIMERGY RX1330 M4 Upgrade And Maintenance Manual

Hide thumbs Also See for PRIMERGY RX1330 M4:
1
2
3
4
5
6
Table Of Contents
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
Table of Contents

Quick Links

Upgrade and Maintenance Manual - English
FUJITSU Server PRIMERGY RX1330 M4
Upgrade and Maintenance Manual
04/2022
Table of Contents
loading

Related Manuals for Fujitsu PRIMERGY RX1330 M4

Summary of Contents for Fujitsu PRIMERGY RX1330 M4

  • Page 1 Upgrade and Maintenance Manual - English FUJITSU Server PRIMERGY RX1330 M4 Upgrade and Maintenance Manual 04/2022...
  • Page 2 All hardware and software names used are trademarks of their respective manufacturers. The contents of this manual may be revised without prior notice. – Fujitsu assumes no liability for damages to third party copyrights or other rights arising from – the use of any information in this manual.
  • Page 3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure that these safety notes are understood before using the product.
  • Page 4 Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning.
  • Page 5 HDD, see the following internet address: https://jp.fujitsu.com/platform/server/primergy/harddisk/ Only for Japan: Shielded LAN cables should be used in this product. UK Importer information Fujitsu Services Limited 22 Baker Street, London, W1U 3BW, United Kingdom RX1330 M4 Upgrade and Maintenance Manual...
  • Page 6 Version history Issue Issue date Description number V 1.0 11/2018 Initial release V 2.0 09/2019 New text Chassis ID Prom Tool, new CPU types V 3.0 01/2021 Note for memory modules added V 4.0 06/2021 – Verifying system information backup/restore –...

  • Page 7: Table Of Contents

    Content Introduction Concept and target groups of this manual Notational conventions Before you start Basic information 2.1.1 Proceeding 2.1.2 Advanced Thermal Design (ATD) 2.1.3 Installing optional components 2.1.4 Replacing a defective component Classification of procedures 2.2.1 Assignment of unit categories 2.2.2 Customer Replaceable Units (CRU) 2.2.3...
  • Page 8 Content 3.2.3 Installation and operation 3.2.4 Batteries 3.2.5 Working with optical disk drives (ODDs) and media 3.2.6 Laser information 3.2.7 Modules with Electrostatic-Sensitive Devices (ESD modules) 3.2.8 Transporting the server 3.2.9 Installing the server in the rack 3.2.10 Other important information ENERGY STAR CE conformity FCC Class A Compliance Statement...
  • Page 9 Content Switching on the server Handling riser modules 4.8.1 Removing a riser module 4.8.2 Installing a riser module Handling the air duct 4.9.1 Removing the air duct 4.9.2 Installing the air duct Basic software procedures Validation Starting the maintenance task 5.2.1 Suspending BitLocker functionality 5.2.2...
  • Page 10 Installing a hot-plug PSU 6.4.3 Removing a hot-plug PSU 6.4.4 Replacing a hot-plug PSU 6.4.5 Replacing the power distribution board Fujitsu battery unit (FJBU) 6.5.1 Installing an FJBU 6.5.2 Removing an FJBU 6.5.3 Replacing an FJBU Converting a standard power supply to a redundant power...
  • Page 11 Content Hard disk drive (HDD) / solid state drive (SSD) Safety notes Basic information Handling HDDs or SSDs without installation frame 7.3.1 2.5-inch HDD/SSD and 2.5-inch installation frame 7.3.2 2.5-inch HDD/SSD and 3.5-inch installation frame 7.3.3 3.5-inch HDD and 3.5-inch installation frame 3.5-inch HDD configurations 7.4.1 Overview of configurations...
  • Page 12 Content Basic information Replacing fan modules Expansion cards and backup units Safety notes Basic information Handling slot brackets 9.3.1 Installing slot brackets 9.3.2 Removing slot brackets Handling SFP+ transceiver modules 9.4.1 Installing SFP+ transceiver modules 9.4.2 Removing SFP+ transceiver modules Expansion cards and riser cards 9.5.1 Installing an expansion card...
  • Page 13 Content 10.4 Removing memory modules 10.5 Replacing memory modules Processor (CPU) 11.1 Safety notes 11.2 Basic information 11.3 Upgrading or replacing the CPU 11.4 Replacing the heat sink Accessible drives 12.1 Safety notes 12.2 Basic information 12.3 Optical disk drive (ODD) 12.3.1 Installing the ODD 12.3.2...
  • Page 14 Content 13.5 Front panel on QRL (10x 2.5-inch HDD) 13.5.1 Replacing the front panel on QRL Serial interface 14.1 Safety notes 14.2 Installing the serial interface 14.3 Removing the serial interface 14.4 Replacing the serial interface System board and components 15.1 Safety notes 15.2...
  • Page 15 Content 15.7 Dual microSD 64GB Enterprise 15.7.1 Installing the Dual microSD 64GB Enterprise 15.7.2 Removing the Dual microSD 64GB Enterprise 15.7.3 Replacing the Dual microSD 64GB Enterprise 15.7.4 Replacing the microSD card 15.8 System board 15.8.1 Replacing the system board Appendix A 16.1 Mechanical overview...
  • Page 16 Content Appendix B 17.1 Supplied documents Upgrade and Maintenance Manual RX1330 M4...

  • Page 17: Introduction

    Introduction Concept and target groups of this manual This upgrade and maintenance manual provides instructions for the following procedures: – Upgrading the server configuration by adding optional hardware components. – Upgrading the server configuration by replacing existing hardware components with superior ones. –...
  • Page 18 Introduction "Quotation marks" Indicate names of chapters and terms that are being emphasized. ▶ Describes activities that must be performed in the order shown. [Abc] Indicates keys on the keyboard. Pay particular attention to texts marked with this CAUTION symbol. Failure to observe this warning may endanger your life, destroy the system or lead to the loss of data.

  • Page 19: Before You Start

    Before you start Basic information 2.1.1 Proceeding Before you start any upgrade or maintenance task, proceed as follows: ▶ Carefully read the safety instructions, see "Important information" on page ▶ Make sure that all necessary manuals are available, see "About availability of manuals"...

  • Page 20: Installing Optional Components

    For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/ Please contact your local Fujitsu customer service partner for details on how to order expansion kits or spare parts. 2.1.4 Replacing a defective component The Global Error indicator on the front of the server reports defective hardware components that need to be replaced.

  • Page 21: Classification Of Procedures

    At the beginning of each procedure, the involved unit category is indicated by one of the symbols introduced in this section. Please ask your local Fujitsu service center for more information. 2.2.2 Customer Replaceable Units (CRU)

  • Page 22: Upgrade And Repair Units (Uru)

    (Repair Units). For Japan, customer allows only upgrade. For upgrade units as customer replaceable, see: https://www.fujitsu.com/jp/products/computing/servers/primergy/ Server management error messages and diagnostic indicators on the front panel and system board will report defective Upgrade and Repair Units as customer replaceable CSS components.

  • Page 23: Field Replaceable Units (Fru)

    Before you start CAUTION The device may be seriously damaged or cause damage if it is opened without authorization or if repairs are attempted by unauthorized and untrained personnel. Components that are handled as Upgrade Units – CPU (upgrade kits) –...
  • Page 24 CAUTION Maintenance procedures involving Field Replaceable Units must be performed exclusively by Fujitsu service personnel or technicians trained by Fujitsu. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Components that are handled as Field Replaceable Units –...

  • Page 25: Average Task Duration

    Before you start Average task duration Hardware: 10 minutes The average task duration including preliminary and concluding steps is indicated at the beginning of each procedure next to the procedure class. The following table gives an overview of steps taken into account for calculating the average task duration.

  • Page 26: Tools You Need At Hand

    Important safety information, available online, Regulations" manual or as a printed copy "安全上のご注意" for Japan "FUJITSU Server Information how to install, set up and operate PRIMERGY RX1330 M4 your server, available online Operating Manual" Upgrade and Maintenance Manual RX1330 M4...
  • Page 27 Before you start Document Description "FUJITSU Server Instructions for upgrading the server PRIMERGY RX1330 M4 configuration or replacing defective hardware, Upgrade and Maintenance available online Manual" "D3675 BIOS Setup Utility Information on configurable BIOS options and for FUJITSU Server parameters, available online PRIMERGY RX1330 M4 Reference Manual"...
  • Page 28 "保証書" for Japan printed copy "Returning used devices" Recycling and contact information, available manual online at https://ts.fujitsu.com/recycling, or as a printed copy "Service Desk" leaflet Not applicable in Japan and other countries that "サポート＆サービス" for have different regulations for recycling...

  • Page 29: Important Information

    Important information Introduction In this chapter you will find essential information regarding safety when working on your server. Depending on your server or the installed options some information is not valid for your server. CAUTION ▶ Before installing and starting up a server, please observe the safety instructions listed in the following section.

  • Page 30: Before Starting Up

    Important information ▶ Only valid for non hot-plug components Before installing/removing internal components to/from the server, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cords from the power outlet. Failure to do so can cause electric shock or damage.
  • Page 31 Important information ▶ If a DC power cord is used, the server must be connected to a proper DC source and earth ground stud/end. ▶ Ensure that the server is connected to a properly grounded power outlet close to the server. ▶...
  • Page 32 Important information ▶ Proper operation of the server (in accordance with IEC 60950-1/62368-1 resp. EN 60950-1/62368-1) is only ensured if the server is completely assembled and the rear covers for the installation slots have been fitted (electric shock, cooling, fire protection, interference suppression). ▶...

  • Page 33: Batteries

    Important information ▶ Install the screw removed during installation/detaching internal options in former position. To use a screw of the different kind can cause a breakdown of equipment. ▶ The procedure of installation on this notes might change depending on a configuration of option.
  • Page 34 Important information CAUTION ▶ Only use CDs/DVDs/BDs that are in perfect condition, in order to prevent data loss, equipment damage and injury. ▶ Check each CD/DVD/BD for damage, cracks, breakages etc. before inserting it in the drive. Note that any additional labels applied may change the mechanical properties of a CD/DVD/BD and cause imbalance and vibrations.

  • Page 35: Laser Information

    Important information ▶ Do not bend or place heavy objects on CDs/DVDs/BDs. ▶ Do not write with ballpoint pen or pencil on the label (printed) side. ▶ Do not attach stickers or similar to the label side. Doing so may cause rotational eccentricity and abnormal vibrations.
  • Page 36 Important information Figure 1: ESD label The ESD label can be different. When you handle ESD modules, you must always observe the following points: ▶ Switch off the server and remove the power plugs from the power outlets before installing or removing ESD modules. ▶...

  • Page 37: Transporting The Server

    Important information 3.2.8 Transporting the server CAUTION ▶ Only transport the server in its original packaging or in packaging that protects it from impacts and jolts. In Japan and APAC, transporting the server in its original packaging does not apply. ▶...

  • Page 38: Installing The Server In The Rack

    Important information 3.2.9 Installing the server in the rack CAUTION ▶ For safety reasons, at least 2 people are required to install the server in the rack because of its weight and size. (For Japan, see "安全上のご注意".) ▶ Never lift the server into the rack using the QRLs on the front panel. ▶...

  • Page 39: Energy Star

    ▶ Select the product class, e.g. "Industry Standard Servers". ▶ Select the subclass, e.g. "Rack server". ▶ Select your server, e.g. "PRIMERGY RX1330 M4". ▶ Select the document, e.g. "CE Cert PRIMERGY RX1330 M4". RX1330 M4 Upgrade and Maintenance Manual...

  • Page 40: Fcc Class A Compliance Statement

    ▶ Consult the dealer or an experienced radio/TV technician for help. Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.

  • Page 41: Environmental Protection

    Important information Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account.
  • Page 42 More information can be found at: https://ts.fujitsu.com/recycling Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu branch, or at: https://ts.fujitsu.com/recycling Upgrade and Maintenance Manual RX1330 M4...

  • Page 43: Basic Hardware Procedures

    Basic hardware procedures Using diagnostic information 4.1.1 Proceeding Use the Fujitsu ServerView Suite management software to plan the upgrade or replacement of hardware components: ▶ In ServerView Operations Manager Single System View select Maintenance from the Information/Operation menu. It is recommended to prepare local maintenance tasks using remote diagnostics procedures, see the "ServerView Suite Local Service Concept...

  • Page 44: Determining The Error Class

    Basic hardware procedures Using the ServerView Operations Manager ▶ To toggle the ID indicator from the ServerView Operations Manager, choose Single System View and press the Locate button. Using the Infrastructure Manager ▶ To toggle the ID indicator from the Infrastructure Manager, select a node from the Node List screen and operate the ID indicator from the Action button.

  • Page 45: Shutting Down The Server

    Basic hardware procedures For more information, see the "ServerView Suite Local Service Concept (LSC)" manual. Possibilities to get more information about the defective component – Checking the ServerView System Monitor, available on Windows or Linux based servers with ServerView agents installed. For more information, see the "ServerView System Monitor"...

  • Page 46: Disconnecting The Power Cord

    Basic hardware procedures This step is only required when upgrading or replacing non-hot-plug components. ▶ Inform the system administrator that the server will be shut down and put offline. ▶ Terminate all applications. ▶ Perform the required procedures described in the preliminary steps of each upgrade or maintenance task.
  • Page 47 Basic hardware procedures ▶ Pull out on the locking lever on the cable tie (1) and loosen the loop (2). ▶ Disconnect the power cord from the PSU and remove it from the cable tie. Redundant power supply   Figure 3: Unlocking the cable clamp of a PSU ▶...

  • Page 48: Getting Access To The Component

    Basic hardware procedures Getting access to the component CAUTION ▶ Only for non-hot plug components: ● Before removing or attaching covers, turn off the server, all peripheral devices, and any other connected devices. ● Because there is a risk of electric shock or damage, please disconnect all power cords from the outlet.

  • Page 49: Removing The Server From The Rack

    Basic hardware procedures Figure 4: Extending the server out of the rack ▶ Fold down the two quick release levers (1). ▶ Pull the server out of the rack until it locks in place (2). CAUTION ▶ Do not use the extended server as a surface on which to put things or as a work surface, and strictly avoid leaning on or against it.
  • Page 50 Basic hardware procedures For configurations below 32 kg: At least two people are needed to lift the server out of the rack cabinet. For configurations below 55 kg: At least three people are needed to lift the server out of the rack cabinet.

  • Page 51: Removing The Top Cover

    Basic hardware procedures Figure 5: Removing the server from the rack ▶ Release the locking bars on both rack rails (1). ▶ Lift the server out of the rack rails (2) and place it on an even surface. 4.4.3 Removing the top cover Figure 6: Removing the top cover RX1330 M4 Upgrade and Maintenance Manual...

  • Page 52: Reassembling

    Basic hardware procedures ▶ Push green touch points inside (1). ▶ Push the top cover as far as it will go in the direction of the arrow (2). ▶ Lift off the top cover upward (3). Reassembling CAUTION ▶ Before attaching the covers, make sure no unnecessary parts or tools are left inside the server.

  • Page 53: Installing The Server In The Rack

    Basic hardware procedures 4.5.2 Installing the server in the rack CAUTION At least two people are needed to position the server on the rack rails. (For Japan, see "安全上のご注意".) For configurations below 32 kg: At least two people are needed to lift the server into the rack cabinet.
  • Page 54 Basic hardware procedures Figure 8: Inserting the server into the rack rails ▶ Fully extend the rack rails until they lock in place (1). The rack rails must click into place so that they can no longer be moved. ▶ At a slight angle, lower the server onto the rear mounting point on the rack rails (2).

  • Page 55: Sliding The Server Into The Rack

    Basic hardware procedures 4.5.3 Sliding the server into the rack Figure 9: Sliding the server into the rack ▶ Release the locking mechanism of both rails (1). ▶ Push the server as far as it will go into the rack (2) until the quick-release levers engage (3).

  • Page 56: Connecting The Power Cord

    Basic hardware procedures Connecting the power cord CAUTION The server automatically adjusts to a mains voltage in the range from 100 V - 240 V. ▶ You may only operate the server if its rated voltage range corresponds to the local mains voltage. Standard power supply ▶...
  • Page 57 Basic hardware procedures It will take about 60 seconds until the server can be powered on. Redundant power supply ▶ If applicable, connect the mains plugs to power outlets of the rack socket strip. To provide true phase redundancy, the second PSU should be connected to a different AC power source from the other PSU.

  • Page 58: Switching On The Server

    Basic hardware procedures ▶ Press the cable clamp down until it engages to secure the cable (3). It will take about 60 seconds until the server can be powered on. Switching on the server CAUTION ▶ Before switching on the server, make sure the top cover is closed. In order to comply with applicable EMC regulations (regulations on electromagnetic compatibility) and satisfy cooling requirements, the server must not run while the top cover is removed.

  • Page 59: Handling Riser Modules

    Basic hardware procedures Handling riser modules 4.8.1 Removing a riser module Figure 12: Removing the riser module 1 Figure 13: Removing the riser module 2 RX1330 M4 Upgrade and Maintenance Manual...
  • Page 60 Basic hardware procedures Figure 14: Removing the riser module 3 Figure 15: Removing the full height riser module ▶ If necessary, disconnect the cables from the other components. ▶ Carefully pull out the corresponding riser module upward. Upgrade and Maintenance Manual RX1330 M4...

  • Page 61: Installing A Riser Module

    Basic hardware procedures 4.8.2 Installing a riser module Figure 16: Installing the riser module 1 Figure 17: Installing the riser module 2 RX1330 M4 Upgrade and Maintenance Manual...
  • Page 62 Basic hardware procedures Figure 18: Installing the riser module 3 Figure 19: Installing the full height riser module Upgrade and Maintenance Manual RX1330 M4...

  • Page 63: Handling The Air Duct

    Basic hardware procedures ▶ Insert the riser card into the system board slot and press down the green touch points (see circles). CAUTION Valid for the full height riser module: ▶ Make sure that the EMC springs make contact correctly (see close-ups).

  • Page 64: Installing The Air Duct

    Basic hardware procedures ▶ Carefully pull out the air duct upward using the green touch points (see circles). 4.9.2 Installing the air duct Figure 21: Installing the air duct ▶ Carefully place the air duct on the CPU. Ensure that the hooks on the right side fit in the fan cage (see close-ups).

  • Page 65: Basic Software Procedures

    Basic software procedures Validation Depending on your server and the installed features some information is not valid for your server. Starting the maintenance task 5.2.1 Suspending BitLocker functionality BitLocker Drive Encryption provides protection for OS and data drives by encrypting the contents and requiring users to authenticate their credentials to access the information.

  • Page 66: Disabling The Boot Watchdog

    Group Policy settings. For more information on how to suspend BitLocker drive encryption, see the Microsoft TechNet library at: https://technet.microsoft.com/library/cc731549.aspx For more information, see the Fujitsu web pages. 5.2.2 Disabling the boot watchdog The boot watchdog determines whether the OS boots within a preset time frame.
  • Page 67 Basic software procedures task. Otherwise, the boot watchdog might initiate a system reboot before the flash process is complete. CAUTION An incomplete firmware upgrade process may render the server inaccessible or result in damaged/destroyed hardware. Timer settings can be configured in the BIOS or using the ServerView iRMC web interface.

  • Page 68: Removing Backup And Optical Disk Media

    Please contact Fujitsu support, if "forcible" tape ejection is necessary. Fujitsu does not assume responsibility for any damage to the tape drive, the data cartridge/tape or for the loss of any data resulting from manual tape extraction procedures.

  • Page 69: Completing The Maintenance Task

    Basic software procedures Using the ID button on the front panel ▶ Press the ID button on the front panel to switch on the system identification LEDs. For more information, see "Indicators on the front panel" on page 346. Using the ID icon in the iRMC S5 web interface ▶...
  • Page 70 After updating or recovering the BIOS and iRMC, enable the boot watchdog again, see "Enabling the boot watchdog" on page Fujitsu does not assume responsibility for any damage done to the server or for the loss of any data resulting from BIOS updates. BIOS flash procedure ▶...

  • Page 71: Verifying System Information Backup Or Restore

    Basic software procedures 5.3.2 Verifying system information backup or restore To avoid the loss of non-default settings when replacing the system board, a backup copy of important system configuration data is automatically stored from the system board NVRAM to the Chassis ID EPROM. After replacing the system board the backup data is restored from the Chassis ID board to the new system board.

  • Page 72: Updating Expansion Card Firmware

    – ServerView Update Manager Express: "Local System Update for PRIMERGY Servers" user guide Using the flash tool The latest firmware files are available as ASPs (Autonomous Support Packages) for Windows or as Linux tools from the Fujitsu support web pages https://ts.fujitsu.com/support/ Upgrade and Maintenance Manual RX1330 M4...

  • Page 73: Enabling Option Rom Scan

    Basic software procedures For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/ 5.3.4 Enabling Option ROM scan In order to configure an expansion card that has been installed or replaced, the Option ROM of the card has to be enabled in the BIOS. The firmware of the card is called by the BIOS upon reboot and can be entered and configured.

  • Page 74: Reconfiguring The Backup Software Solution

    More information on suitable backup software solutions and related documentation is available from the Fujitsu web pages. Re-enabling backup drives If a backup drive has been disabled or deleted from the backup software drive list (see "Verifying and configuring the backup software solution"...
  • Page 75 Basic software procedures ▶ Exit the BIOS. Resetting the boot retry counter The boot retry counter should be reset to its original value concluding every service task. Please note, if the customer does not know about the original boot retry values: If the system boots up and no further errors occur within 6 hours after that successful boot attempt, the boot retry counter will automatically be...

  • Page 76: Resetting The Error Status After Replacing Memory Modules Or Cpu

    Using ServerView Maintenance Tools (Windows only) ▶ Launch the ServerView Maintenance Tools: Start > Apps > Fujitsu > Maintenance Tools ▶ Choose the Memory status tab. Upgrade and Maintenance Manual RX1330 M4...
  • Page 77 Basic software procedures ▶ Select the memory module which shows the pre-failure status. ▶ Click on Reset Status. The Reset Status button will only be available if the selected memory module contains errors. ▶ Ensure that all pre-fail/fail status issues have been resolved in ServerView Operations Manager.

  • Page 78: Resetting The Error Status After Replacing Cpus

    Using ServerView Maintenance Tools (Windows only) ▶ Launch the ServerView Maintenance Tools: Start > Apps > Fujitsu > Maintenance Tools ▶ Choose the CPU status tab. ▶ Select the CPU which shows the pre-failure status.
  • Page 79 Basic software procedures ▶ Enter the command below, followed by [ENTER]: parameters are "0" for CPU 1 and "1" for CPU 2. For rack and floorstand servers (RX and TX server series): /usr/sbin/eecdcp -c oc=0609 oi= For blade and scale-out servers (BX and CX server series): /usr/sbin/eecdcp -c oc=0609 oi=...

  • Page 80: Enabling The Boot Watchdog

    Basic software procedures When replacing the CPU, the status will be updated after getting information manually or automatically updated daily. Proceed as follows to get node information with Infrastructure Manager: ▶ Start up the GUI of the Infrastructure Manager and login. ▶...

  • Page 81: Enabling Replaced Components In The Bios

    Basic software procedures ▶ Select Reset from the Watchdog Action list. ▶ Click Apply for the changes to take effect. For more information on iRMC settings, see the iRMC user guides. 5.3.9 Enabling replaced components in the BIOS When a CPU, an expansion card, or a memory module fails, the defective component will be set to Disabled or Failed in the BIOS.

  • Page 82: Verifying The System Time Settings

    Basic software procedures pairs. In this case, the operation mode will automatically revert to Independent Channel Mode. For more information on memory operation modes available for your server, see "Modes of operation" on page 235. After replacing the defective module(s) the memory operation mode is automatically reset to its original state.

  • Page 83: Viewing And Clearing The System Event Log (Sel)

    Basic software procedures ▶ Select the Main menu. ▶ Under System Time and System Date specify the correct time and date. By default, the system time set in the BIOS is RTC (Real Time Clock) local time. If your IT infrastructure relies on universally accepted time standards, set the System Time to UTC (Universal Time, Coordinated) instead.
  • Page 84 Basic software procedures Note on the Driver Monitor of the ServerView Operations Manager The Driver Monitor view gives you an overview of the monitored components as well as the associated events contained in the system event log on the managed server. Under Monitored Components the monitored components are listed.

  • Page 85: Updating The Nic Configuration File In A Linux And Vmware Environment

    The Infrastructure Manager can collect various logs including System Event Log for system operation and maintainance. Please refer to the following manuals of Infrastructure Manager for collecting logs from ISM. See manual "FUJITSU Software Infrastructure Manager V2.6.0 User's Guide", section "2.5 Log Management", available at: https://ts.fujitsu.com/support/ For Japan: See manual "FUJITSU Software Infrastructure Manager V2.6.0 解説書",...

  • Page 86: Resuming Bitlocker Functionality

    Basic software procedures interface card in the related NIC configuration file of the Linux/VMware OS. When replacing a network controller or the system board with onboard LAN controllers in a server running Linux/VMware OS, the MAC address will change but not automatically be updated in the definition file. In order to prevent communication problems, it is necessary to update the changed MAC address stored in the related ifcfg-eth...

  • Page 87: Performing A Raid Array Rebuild

    For more information on how to resume BitLocker drive encryption, see the Microsoft TechNet library at: https://technet.microsoft.com/library/cc731549.aspx For more information, see the Fujitsu web pages. 5.3.15 Performing a RAID array rebuild After replacing an HDD that has been combined into a RAID array, RAID rebuild will be performed completely unattended as a background process.

  • Page 88: Looking For Mac/Wwn/Guid And Sas Addresses

    Basic software procedures Figure 22: Progress bar (RAID array rebuild) CAUTION The system is now operational, however, data redundancy will not be available until the RAID array rebuild is complete. Depending on the HDD capacity the overall process can take up to several hours, in some cases even days.

  • Page 89: Looking For The Mac Address Of A Lan Controller

    Basic software procedures Different controllers send different addresses: – LAN controller: MAC (Media Access Control) address – Fibre channel controller: WWN (World Wide Name) address – Infiniband/Omni-Path controller: GUID (Globally Unique IDentifier) address – SAS controller: SAS (Serial Attached SCSI) address 5.3.16.2 Looking for the MAC address of a LAN controller There are several possible locations where these addresses can be found.

  • Page 90: Looking For The Wwn Address Of A Fibre Channel Controller

    Command Line Protocol (CLP) will be displayed. For add-in cards the vendors provide documentation and tools, offered on the Fujitsu support web pages: https://ts.fujitsu.com/support/ Select the server, select Downloads - More Details - Driver. Some vendors bundle the documentation together with the driver package.

  • Page 91: Looking For Sas Addresses Of Sas Controllers For External Devices

    There are several possible locations where these addresses can be found. ▶ Inform the customer about the new SAS address. The customer need the new SAS address, especially when the server is connected to a Fujitsu Storage ETERNUS system. Using ServerView RAID Manager ▶...
  • Page 92 – from rack model to floorstand model – from floorstand model to rack model Update your system information using the Chassis ID Prom tool. The tool and more information are available to maintenance personnel from the Fujitsu web pages: https://partners.ts.fujitsu.com/com/service/ps/Servers/PRIMERGY/ ▶...

  • Page 93: Configuring Lan Teaming

    Basic software procedures ▶ In the Tools area click Tools: Chassis-IDProm Tool to download the file (tool-chassis-Idprom-Tool.zip). For Japan: Follow the instructions provided separately. Note on Advanced Thermal Design (ATD) If the Advanced Thermal Design (ATD) option is available and has been enabled for your server, please set information within the Chassis ID Prom Tool accordingly.
  • Page 94 Please refer to the following manuals of the Infrastructure Manager. See manual "FUJITSU Software Infrastructure Manager V2.6.0 User's Guide", section "2.4.2 Profiles and Policies", available at: https://ts.fujitsu.com/support/ For Japan: See manual "FUJITSU Software Infrastructure Manager V2.6.0 解説書",...

  • Page 95: Switching Off The Id Indicator

    Basic software procedures For more information, see the relevant LAN driver manual. 5.3.19 Switching off the ID indicator ▶ Press the ID button on the front panel, or use the ServerView Operations Manager, the iRMC S5 web interface or the Infrastructure Manager to switch off the ID indicator after the maintenance task has been concluded successfully.

  • Page 96: Performing A Fan Test

    Basic software procedures 5.3.20 Performing a fan test Notes on replacing a defective fan After replacing a defective system fan or PSU containing a defective fan, the fan error indicators will stay lit until the next fan test. By default, a fan test is automatically started every 24 hours.
  • Page 97 ▶ After the fan test is complete, restore the time setting to its initial value and click Save Page. In case of maintenance done by Fujitsu engineers in Japan: Executing the fan test via Chassis ID Prom Tool Please follow the instructions provided separately.
  • Page 98 Basic software procedures Upgrade and Maintenance Manual RX1330 M4...

  • Page 99: Power Supply Unit (Psu)

    – a standard PSU – up to two hot-plug PSUs – one hot-plug PSU and a Fujitsu battery unit (FJBU) Server equipped with a standard PSU The PSU adjusts automatically to any mains voltage in the range of 100 V - 240 V.

  • Page 100: Standard Power Supply

    PSU can be replaced during operation (hot-plug). Server equipped with one hot-plug PSU and a Fujitsu battery unit (FJBU) Besides the PSU, an FJBU can be installed optionally as a modular UPS. When power fail happened, the server can operate via FJBU for a while. The FJBU can be replaced during operation (hot-plug).
  • Page 101 Power supply unit (PSU) ▶ "Disconnecting the power cord" on page 46 ▶ "Getting access to the component" on page 48 Removing the defective standard PSU Figure 23: Disconnecting the power cables ▶ Disconnect the two power cables from the system board connectors "PC98" and "PWR MAIN".
  • Page 102 Power supply unit (PSU) ▶ Remove the two screws (see circles). Figure 25: Removing the standard PSU ▶ Remove the two screws (1). ▶ Pull the PSU a few centimeters toward the inside (2). ▶ Take the PSU out upward (3). Upgrade and Maintenance Manual RX1330 M4...
  • Page 103 Power supply unit (PSU) Installing the new standard PSU Figure 26: Installing the standard PSU ▶ Insert the PSU into the bay (1). ▶ Push the PSU toward the adapter plate (2). ▶ Fasten the PSU with two screws in the chassis (3). ▶...
  • Page 104 Power supply unit (PSU) Figure 27: Connecting the power cables ▶ Connect the power cables to the system board: For the cable plans, see "Appendix B" on page 365. ▶ PSU power cable (1) to connector "PWR MAIN". ▶ Power signal cable (2) to connector "PC98". Concluding steps ▶...

  • Page 105: Redundant Power Supply

    Power supply unit (PSU) Redundant power supply 6.4.1 PSU bays PSU 1 PSU 2 Figure 28: PSU bays 6.4.2 Installing a hot-plug PSU Customer Replaceable Hardware: 5 minutes Unit (CRU) Tools: Tool-less Preliminary steps No steps needed. Removing the dummy cover Figure 29: Removing the dummy cover ▶...
  • Page 106 Power supply unit (PSU) CAUTION ▶ Keep the dummy cover for future use. ▶ If you remove a PSU and do not immediately replace it with a new one, a dummy cover must be installed in the bay again to comply with applicable EMC regulations and satisfy cooling requirements.
  • Page 107 Power supply unit (PSU) Figure 31: Installing the PSU ▶ Push the PSU into its bay (1) as far as it will go until the release latch snaps in place. ▶ Fold down the handle on the PSU (2). Ensure that the PSU engages correctly in the bay and is locked in position.

  • Page 108: Removing A Hot-Plug Psu

    Power supply unit (PSU) Figure 32: Installing the cable clamp ▶ Push the cable clamp into the corresponding hole until it clicks in. Concluding steps ▶ "Connecting the power cord" on page ▶ "Performing a fan test" on page 6.4.3 Removing a hot-plug PSU Customer Replaceable Hardware: 5 minutes...
  • Page 109 Power supply unit (PSU) Figure 33: Unlocking the CMA stopper ▶ Push the lock spring inward to unlock the CMA stopper. CAUTION ▶ In case of not enough space at the under side, unlock the CMA stopper of the server below and pull out the CMA to the rear side.
  • Page 110 Power supply unit (PSU) Figure 34: Removing the CMA stopper ▶ Remove the CMA stopper with the mounted crossbar. ▶ Hold the CMA stopper, the crossbar and the CMA including cables in the one hand. Figure 35: Removing the PSU Upgrade and Maintenance Manual RX1330 M4...
  • Page 111 Power supply unit (PSU) ▶ Remove the PSU and install the dummy cover carefully. Note for PSU1: Remove the PSU1 carefully while lifting PSU1 and bringing PSU1 to the right, in order to avoid interference. ▶ Mount the complete assembly (CMA stopper, the crossbar and the CMA) again into the rail.

  • Page 112: Replacing A Hot-Plug Psu

    Power supply unit (PSU) ▶ While keeping the green locking latch pressed, pull the PSU out of its bay (3). CAUTION Excessive temperatures could damage system components. ▶ Never leave the bay for the hot-plug PSU empty for more than two minutes during operation.
  • Page 113 Power supply unit (PSU) Tools: tool-less CAUTION ▶ When replacing a PSU in a non-redundant PSU configuration, the server must be switched off first. ▶ Replace the PSU after specifying the one that breaks down at work by revitalization. Note for servers using CMA (Cable Management Arm) Regarding of removing PSUs, additional tasks are needed, due to an interference between CMA and the PSUs.

  • Page 114: Replacing The Power Distribution Board

    Power supply unit (PSU) ▶ Remove the power cord from the defective PSU, see "Disconnecting the power cord" on page Removing the defective hot-plug PSU ▶ Remove the PSU, see "Removing a hot-plug PSU" on page 108. Installing the new hot-plug PSU ▶...
  • Page 115 Power supply unit (PSU) Removing the defective power distribution board ▶ Remove all PSUs, see "Removing a hot-plug PSU" on page 108. Figure 38: Disconnecting the front USB cable and the front panel cable ▶ Recommended for servers with front panel module: disconnect the front USB cable and the front panel cable from the system board.
  • Page 116 Power supply unit (PSU) Figure 39: Disconnecting cables (A) ▶ Disconnect the two power cables and the flat band cable from the system board (see blue arrows). ▶ Disconnect the HDD power cable from the power distribution board (see orange arrow). Upgrade and Maintenance Manual RX1330 M4...
  • Page 117 Power supply unit (PSU) Figure 40: Removing the power distribution board ▶ Remove one screw (see circle). ▶ Lift the power distribution board out of the centering ring on the standoff (1) and move it in direction to the system board (2). ▶...
  • Page 118 Power supply unit (PSU) Figure 41: Disconnecting cables (B) ▶ Disconnect the remaining cables from the defective power distribution board (see arrows). Upgrade and Maintenance Manual RX1330 M4...
  • Page 119 Power supply unit (PSU) Installing the new power distribution board Figure 42: Installing the power distribution board ▶ Insert the power distribution board (1) and slide it in the guidings of the chassis (2). ▶ Fasten the power distribution board with one screw (see circle). RX1330 M4 Upgrade and Maintenance Manual...
  • Page 120 Power supply unit (PSU) Figure 43: Connecting cables (A) ▶ Connect the flat band cable to the system board and the power distribution board. Upgrade and Maintenance Manual RX1330 M4...
  • Page 121 Power supply unit (PSU) Figure 44: Connecting the front USB cable and the front panel cable ▶ If disconnected before: connect the front panel cable and the front USB cable to the system board. Ensure that the front panel cable is situated under the front USB cable.
  • Page 122 Power supply unit (PSU) Figure 45: Connecting cables (B) ▶ Connect the power cable to the system board and the power distribution board (1). ▶ Connect the HDD power cable to the power distribution board (2). Upgrade and Maintenance Manual RX1330 M4...
  • Page 123 Power supply unit (PSU) Figure 46: Connecting power cables (C) ▶ Connect the power cable to the system board and the power distribution board. ▶ Install the PSUs, see "Installing a hot-plug PSU" on page 105. Concluding steps ▶ "Reassembling" on page ▶...

  • Page 124: Fujitsu Battery Unit (Fjbu)

    Power supply unit (PSU) Fujitsu battery unit (FJBU) 6.5.1 Installing an FJBU Customer Replaceable Hardware: 5 minutes Unit (CRU) Tools: tool-less Preliminary steps No steps needed. Removing the dummy cover ▶ Remove the dummy cover, see "Removing the dummy cover" on page 105.

  • Page 125: Removing An Fjbu

    Power supply unit (PSU) To execute auto shutdown after power fail, you should install the FJBU management software. How to install and configure the FJBU management software, see the “Fujitsu Battery Unit" user guide. 6.5.2 Removing an FJBU Customer Replaceable...

  • Page 126: Replacing An Fjbu

    Power supply unit (PSU) Removing an FJBU Figure 48: Removing an FJBU ▶ Press in on the green locking latch (1). ▶ While keeping the green locking latch pressed, pull the FJBU out of its bay (2). CAUTION ▶ Never leave the bay for the FJBU empty. ▶...

  • Page 127: Converting A Standard Power Supply To A Redundant Power Supply

    Power supply unit (PSU) ▶ Push the lock spring inward to unlock the CMA stopper, see Figure CAUTION ▶ In case of not enough space at the under side, unlock the CMA stopper of the server below and pull out the CMA to the rear side.
  • Page 128 Power supply unit (PSU) Tools: Phillips PH2 / (+) No. 2 screw driver The standard power supply can be replaced by a redundant power supply. The redundant power supply consists of up to two hot-plug PSUs. The upgrade kit contains only one hot-plug PSU, for PSU redundancy the second hot-plug PSU must be additionally ordered.
  • Page 129 Power supply unit (PSU) Figure 49: Removing the adapter plate ▶ Remove the screw (see circle) which attach the adapter plate of the PSU to the housing. ▶ Push the adapter plate a few centimeters inward to detach it from the two bolts (see close-ups).
  • Page 130 Power supply unit (PSU) Figure 51: Inserting the PSU cage ▶ Insert the PSU cage in the chassis and push it to the rear side. The PSU cage must engage in the five bolts, see "Positions of the bolts" on page 129.
  • Page 131 Power supply unit (PSU) Figure 53: Folding the flat cable ▶ Fold the flat cable as shown. ▶ Install the power distribution board, see "Installing the new power distribution board". ▶ Install the PSU, see "Installing a hot-plug PSU" on page 105.
  • Page 132 Power supply unit (PSU) Figure 54: Removing the foam ▶ Remove the foam. ▶ Install the additional fan, see "Installing the new fan module" on page 181. Concluding steps ▶ "Installing the air duct" on page ▶ "Reassembling" on page ▶...

  • Page 133: Hard Disk Drive (Hdd) / Solid State Drive (Ssd)

    Hard disk drive (HDD) / solid state drive (SSD) Safety notes CAUTION ▶ Before removing several HDD/SSD modules, make sure that all HDD/SSD modules can be reinstalled into their original bay. Otherwise, data may be lost. ▶ Do not touch the circuitry on boards or soldered parts. Hold circuit boards by their metallic areas or edges.

  • Page 134: Basic Information

    Hard disk drive (HDD) / solid state drive (SSD) Basic information The HDD or SSD and the installation frame together make up the HDD module or SSD module. The server is shipped with one of the following HDD or SSD subsystems: –...

  • Page 135: Handling Hdds Or Ssds Without Installation Frame

    Hard disk drive (HDD) / solid state drive (SSD) Handling HDDs or SSDs without installation frame 7.3.1 2.5-inch HDD/SSD and 2.5-inch installation frame Installing or removing the installation frame is only necessary for Japan. Customer Replaceable Hardware: 5 minutes Unit (CRU) Tools: Phillips PH1 / (+) No.

  • Page 136: Inch Hdd/Ssd And 3.5-Inch Installation Frame

    Hard disk drive (HDD) / solid state drive (SSD) Figure 56: Installing the 2.5-inch HDD/SSD in the 2.5-inch installation frame (B) ▶ Fasten the 2.5-inch HDD/SSD with four screws. Removing a 2.5-inch HDD/SSD from a 2.5-inch installation frame ▶ Please proceed in reversed order. Concluding steps No steps needed.
  • Page 137 Hard disk drive (HDD) / solid state drive (SSD) In order to use 2.5-inch HDD/SSD, you can install a 2.5-inch HDD/SSD in the 3.5-inch installation frame. Preliminary steps No steps needed. Installing a 2.5-inch HDD/SSD in a 3.5-inch installation frame Figure 57: Installing the 2.5-inch HDD/SSD in the 3.5-inch installation frame (A) ▶...

  • Page 138: Inch Hdd And 3.5-Inch Installation Frame

    Hard disk drive (HDD) / solid state drive (SSD) Figure 58: Installing the 2.5-inch HDD/SSD in the 3.5-inch installation frame (B) ▶ Fasten the 2.5-inch HDD/SSD with four screws. Removing a 2.5-inch HDD/SSD from a 3.5-inch installation frame ▶ Please proceed in reversed order. Concluding steps No steps needed.
  • Page 139 Hard disk drive (HDD) / solid state drive (SSD) Preliminary steps No steps needed. Installing a 3.5-inch HDD in a 3.5-inch installation frame Figure 59: Installing the 3.5-inch HDD in the 3.5-inch installation frame (A) ▶ Lay the 3.5-inch HDD into the 3.5-inch installation frame as shown. Figure 60: Installing the 3.5-inch HDD in the 3.5-inch installation frame (B) RX1330 M4 Upgrade and Maintenance Manual...

  • Page 140: Inch Hdd Configurations

    Hard disk drive (HDD) / solid state drive (SSD) ▶ Fasten the 3.5-inch HDD with four screws. Removing a 3.5-inch HDD from a 3.5-inch installation frame ▶ Please proceed in reversed order. Concluding steps No steps needed. 3.5-inch HDD configurations 7.4.1 Overview of configurations 7.4.1.1...

  • Page 141: Installing 3.5-Inch Hdd Modules

    Hard disk drive (HDD) / solid state drive (SSD) 7.4.2 Installing 3.5-inch HDD modules Customer Replaceable Hardware: 5 minutes Unit (CRU) Tools: tool-less Preliminary steps ▶ Locate the correct drive bay, see "Overview of configurations" on page 140. Removing a 3.5-inch HDD dummy module Figure 62: Removing the 3.5-inch dummy module ▶...
  • Page 142 Hard disk drive (HDD) / solid state drive (SSD) Installing a 3.5-inch HDD module Figure 63: Opening the locking lever ▶ Pinch the green locking clip (1) and open the locking lever (2). Figure 64: Installing the 3.5-inch HDD module ▶...

  • Page 143: Removing 3.5-Inch Hdd Modules

    Hard disk drive (HDD) / solid state drive (SSD) Concluding steps No steps needed. 7.4.3 Removing 3.5-inch HDD modules Customer Replaceable Hardware: 5 minutes Unit (CRU) Tools: tool-less Preliminary steps ▶ If the HDD module to be removed is combined into a RAID array, please proceed as follows: RAID level Procedure...
  • Page 144 Hard disk drive (HDD) / solid state drive (SSD) CAUTION All data on all HDDs in the array will be lost when deleting the RAID array! ▶ Be sure to back up your data before deleting a RAID array. ▶ For more information, see the "ServerView Suite RAID Management"...

  • Page 145: Replacing A 3.5-Inch Hdd Module

    Hard disk drive (HDD) / solid state drive (SSD) Concluding steps No steps needed. 7.4.4 Replacing a 3.5-inch HDD module Customer Replaceable Hardware: 5 minutes Unit (CRU) Tools: – Installation frame included: tool-less – Installation frame excluded: Phillips PH1 / (+) No. 1 screw driver RX1330 M4 Upgrade and Maintenance Manual...
  • Page 146 Hard disk drive (HDD) / solid state drive (SSD) CAUTION ▶ Only remove an HDD module during operation if the drive is not currently being accessed. Observe the indicators on the corresponding HDD module, see "Indicators on the hot-plug HDD/ SSD module"...

  • Page 147: Replacing The 3.5-Inch Hdd Backplane

    Hard disk drive (HDD) / solid state drive (SSD) Removing the defective 3.5-inch HDD module ▶ Remove the HDD module, see "Removing a 3.5-inch HDD module" on page 144. ▶ If applicable, remove the HDD from the installation frame, see "Handling HDDs or SSDs without installation frame"...
  • Page 148 Hard disk drive (HDD) / solid state drive (SSD) ▶ Release all HDD modules and pull them out a few centimeters, see "Removing a 3.5-inch HDD module" on page 144. CAUTION The HDD modules need not to be removed. ▶ If you want to remove them nevertheless, check if all HDD modules are uniquely identified so that you can reinsert them into their original bays.
  • Page 149 Hard disk drive (HDD) / solid state drive (SSD) ▶ Position the HDD backplane on the three hooks (see circles). ▶ Push the HDD backplane downward. Ensure that the HDD backplane fits into the guides (A). There are five guides, three can be seen in figure. CAUTION ▶...

  • Page 150: Inch Hdd/Ssd Configurations

    Hard disk drive (HDD) / solid state drive (SSD) ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page 2.5-inch HDD/SSD configurations 7.5.1 Overview of configurations 7.5.1.1 Configuration with up to four HDD/SSD modules Figure 69: Configuration with up to four 2.5-inch HDDs/SSDs Position Logical drive ServerView RAID Manager display...

  • Page 151: Configuration With Up To Eight Hdd/Ssd Modules

    Hard disk drive (HDD) / solid state drive (SSD) 7.5.1.2 Configuration with up to eight HDD/SSD modules Figure 70: Configuration with up to eight HDDs/SSDs Position Logical drive ServerView RAID Manager display number name Vendor Product (0) Vendor Product (1) Vendor Product (2) Vendor Product (3) Vendor Product (4)

  • Page 152: Configuration With Up To Ten Hdd/Ssd Modules

    Hard disk drive (HDD) / solid state drive (SSD) Position Logical drive ServerView RAID Manager display number name Vendor Product (2) Vendor Product (3) 7.5.1.3 Configuration with up to ten HDD/SSD modules Figure 71: Configuration with up to 10 HDDs/SSDs Position Logical drive ServerView RAID Manager display...
  • Page 153 Hard disk drive (HDD) / solid state drive (SSD) Tools: tool-less Preliminary steps ▶ Locate the correct drive bay, see 150. Removing a 2.5-inch HDD/SSD dummy module In configuration with only one 4x 2.5-inch HDD backplane dummy locks are installed to make it impossible to equip the bays with no HDD backplane behind.
  • Page 154 Hard disk drive (HDD) / solid state drive (SSD) ▶ Press both tabs together (1) and pull the dummy module out of its bay (2). CAUTION ▶ Keep the dummy module for future use. ▶ Always replace dummy modules into unused HDD/SSD bays to comply with applicable EMC regulations and satisfy cooling requirements.

  • Page 155: Removing 2.5-Inch Hdd/Ssd Modules

    Hard disk drive (HDD) / solid state drive (SSD) ▶ Insert the HDD/SSD module into a drive bay and carefully push back as far as it will go (1). ▶ Close the locking lever to lock the HDD/SSD module in place (2). ▶...
  • Page 156 Hard disk drive (HDD) / solid state drive (SSD) RAID level Procedure RAID 0 CAUTION RAID 0 provides no data redundancy. In case of an HDD module is defect, all data are lost! RAID 1 Removing an HDD/SSD module from a RAID 1 or RAID 5 array will not result in data loss.

  • Page 157: Replacing A 2.5-Inch Hdd/Ssd Module

    Hard disk drive (HDD) / solid state drive (SSD) ▶ Pull the HDD/SSD module completely out of its bay. Installing a 2.5-inch dummy module CAUTION ▶ If the removed HDD/SSD module is not replaced immediately, always replace a dummy module into the unused HDD/SSD bay to comply with applicable EMC regulations and satisfy cooling requirements.
  • Page 158 Hard disk drive (HDD) / solid state drive (SSD) CAUTION ▶ Only remove an HDD/SSD module during operation if the drive is not currently being accessed. Observe the indicators on the corresponding HDD/SSD module, see "Indicators on the hot-plug HDD/SSD module" on page 351.

  • Page 159: Replacing The 4 X 2.5-Inch Hdd Backplane (Left Side)

    Hard disk drive (HDD) / solid state drive (SSD) Removing the defective 2.5-inch HDD/SSD module ▶ Remove the HDD/SSD module, see "Removing a 2.5-inch HDD/SSD module" on page 156. ▶ If applicable, remove the HDD/SSD from the installation frame, see "Handling HDDs or SSDs without installation frame"...
  • Page 160 Hard disk drive (HDD) / solid state drive (SSD) ▶ Release all HDD/SSD modules and pull them out a few centimeters, see "Removing a 2.5-inch HDD/SSD module" on page 156. CAUTION The HDD/SSD modules need not to be removed. ▶ If you want to remove them nevertheless, check if all HDD/SSD modules are uniquely identified so that you can reinsert them into their original bays.
  • Page 161 Hard disk drive (HDD) / solid state drive (SSD) Figure 78: Removing the 4x 2.5-inch HDD backplane ▶ Pull the HDD backplane upward until the six hooks disengage (see circles). ▶ Take out the HDD backplane. Installing the new 4x 2.5-inch HDD backplane Figure 79: Installing the 4x 2.5-inch HDD backplane ▶...
  • Page 162 Hard disk drive (HDD) / solid state drive (SSD) Figure 80: Connecting the cables to the ODD and the 4x 2.5-inch HDD backplane ODD power cable (if applicable) OOB cable to connector "SMBus" ODD data cable (if applicable) Power cable SAS cable to connector "X5"...
  • Page 163 Hard disk drive (HDD) / solid state drive (SSD) 7.5.6 Replacing the 4 x 2.5-inch HDD backplane (right side) or PCIe SSD backplane Field Replaceable Unit Hardware: 5 minutes (FRU) Tools: tool-less Preliminary steps ▶ "Locating the defective server" on page ▶...

  • Page 164: Ssd Backplane

    Hard disk drive (HDD) / solid state drive (SSD) Removing the defective 4x 2.5-inch HDD backplane (right side) or PCIe SSD backplane Figure 81: Removing the 4 x 2.5-inch HDD backplane Figure 82: Removing the 4 x 2.5-inch PCIe SSD backplane ▶...
  • Page 165 Hard disk drive (HDD) / solid state drive (SSD) Installing the new 4x 2.5-inch HDD backplane (right side) or PCIe SSD backplane Figure 83: Installing the 4x 2.5-inch HDD backplane (right side) ▶ Position the HDD backplane on the four hooks (see circles). ▶...
  • Page 166 Hard disk drive (HDD) / solid state drive (SSD) Figure 85: Connecting cables to the 4 x 2.5-inch PCIe SSD backplane Oculink cable (black) to connector Oculink cable (red) to connector "P4_X4" "P1_X1" Oculink cable (green) to connector Power cable "P3_X3"...

  • Page 167: Replacing The 10 X 2.5-Inch Hdd Backplane

    Hard disk drive (HDD) / solid state drive (SSD) 7.5.7 Replacing the 10 x 2.5-inch HDD backplane Field Replaceable Unit Hardware: 15 minutes (FRU) Tools: Phillips PH2 / (+) No. 2 screw driver (for removing/installing SAS expander board) Preliminary steps ▶...
  • Page 168 Hard disk drive (HDD) / solid state drive (SSD) Removing the SAS expander board Figure 86: Disconnecting SAS cables ▶ Disconnect the power cable from the HDD backplane. ▶ Disconnect the two SAS cables from the SAS expander board. Figure 87: Removing the SAS expander board (A) Upgrade and Maintenance Manual RX1330 M4...
  • Page 169 Hard disk drive (HDD) / solid state drive (SSD) ▶ Remove the two screws from the SAS expander board (see circles). Figure 88: Removing the SAS expander board (B) ▶ Get the SAS expander board out of the two connectors of the HDD backplane and remove it.
  • Page 170 Hard disk drive (HDD) / solid state drive (SSD) Installing the new 10x 2.5-inch HDD backplane Figure 90: Installing the 10x 2.5-inch HDD backplane ▶ Position the HDD backplane on the six hooks (see circles). ▶ Push the HDD backplane downward. Make sure that the HDD backplane fits into the guides (A).
  • Page 171 Hard disk drive (HDD) / solid state drive (SSD) Figure 92: Installing the SAS expander board (B) ▶ Fasten the SAS expander board with two screws (see circles). MLC 2 MLC 1 Figure 93: Connecting SAS cables SAS cable to SAS expander board Power cable to backplane SAS cable to SAS expander board ▶...

  • Page 172: Replacing The Sas Expander Board

    Hard disk drive (HDD) / solid state drive (SSD) For the cable plans, see "Appendix B" on page 365. Concluding steps ▶ Insert all HDD/SSD modules, see "Installing 2.5-inch HDD/SSD modules" on page 152. Make sure that you reinstall the HDD/SSD module in the bay it was located before the HDD backplane replacement.

  • Page 173: Upgrading Configuration From Up To Four To Up To Eight 2.5-Inch Hdds/Ssds

    Hard disk drive (HDD) / solid state drive (SSD) Installing the new SAS expander board ▶ Install the SAS expander board, see "Installing the SAS expander board" on page 170. Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶...
  • Page 174 Hard disk drive (HDD) / solid state drive (SSD) Removing the ODD lock ▶ If an ODD has been installed, remove the ODD, see "Removing the ODD" on page 262. Figure 94: Removing the ODD lock (A) ▶ Push the ODD lock in direction of the arrow. Figure 95: Removing the ODD lock (B) ▶...
  • Page 175 Hard disk drive (HDD) / solid state drive (SSD) Installing the second HDD backplane ▶ Install the second HDD backplane, see "Installing the new 4x 2.5-inch HDD backplane" on page 161. ▶ If applicable, install a dual-channel RAID controller, see "Installing an expansion card"...
  • Page 176 Hard disk drive (HDD) / solid state drive (SSD) Upgrade and Maintenance Manual RX1330 M4...

  • Page 177: Fans

    Fans Safety notes CAUTION ▶ Do not damage or modify internal cables or devices. Doing so may cause a device failure, fire, or electric shock. ▶ Devices and components inside the server remain hot after shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.
  • Page 178 Fans Two types of fan modules are available, single fans and dual fans. There is no difference for installing and removing procedures. Numbering of the fan modules In configurations with a Standard PSU, position 3 remains free and is occupied with a foam. Figure 96: Numbering of the single fan modules Fan 1 Fan 4...

  • Page 179: Replacing Fan Modules

    Fans Figure 97: Numbering of the dual fan modules Fan 1 Fan 4 Fan 2 Fan 4 Fan 3 Replacing fan modules Field Replaceable Unit Hardware: 10 minutes (FRU) Tools: tool-less Preliminary steps ▶ "Locating the defective server" on page ▶...
  • Page 180 Fans ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the air duct" on page ▶ "Locating the defective component" on page Removing the defective fan module Figure 98: Removing the fan module ▶...
  • Page 181 Fans Installing the new fan module Figure 99: Installing the fan module (A) ▶ Insert the fan module in the fan bay. Notice the right position of the rubber pins and the fan connector. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 182 Fans Figure 100: Installing the fan module (B) ▶ Press down the fan and the fan connector. Concluding steps ▶ "Installing the air duct" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶...

  • Page 183: Expansion Cards And Backup Units

    Expansion cards and backup units Safety notes CAUTION ▶ Do not damage or modify internal cables or devices. Doing so may cause a device failure, fire, or electric shock. ▶ Devices and components inside the server remain hot after shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options.

  • Page 184: Basic Information

    Expansion cards and backup units Basic information Reset PWR MAIN Front Panel1 Slot 3 PC98 Front USB USB 2.0 PWR3 PWR2 Front Panel2 PWR1 USB 2.0 FAN5 USB 3.1 Gen 2 USB 3.1 Gen 2 FAN4 Intel C246 SERIAL SSD1 SSD2 FAN3 HDD LED...

  • Page 185: Handling Slot Brackets

    214. In this case the slot 2 is not available and slot 3 can be equipped with a full height expansion card. For system relevant information, see the hardware configurator of your server available online at the following address:https://ts.fujitsu.com/ products/standard_servers/index.htm For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/ Handling slot brackets 9.3.1...
  • Page 186 Expansion cards and backup units Figure 102: Perforated and non-perforated slot brackets Full height bracket non-perforated Low profile bracket perforated Full height bracket perforated Installing a slot bracket ▶ Place the controller on the mounting tabs on the slot bracket. ▶...

  • Page 187: Removing Slot Brackets

    Expansion cards and backup units Example: EP4x0i Figure 103: Placing the slot bracket ▶ Place the controller on the slot bracket. ▶ Secure the slot bracket to the expansion card with two screws (see circles). 9.3.2 Removing slot brackets Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools:...

  • Page 188: Handling Sfp+ Transceiver Modules

    Expansion cards and backup units Handling SFP+ transceiver modules 9.4.1 Installing SFP+ transceiver modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less A network adapter is equipped with one or two SFP+ (small form-factor pluggable) transceiver modules. SFP+ transceiver modules are hot-pluggable. Installing SFP+ transceiver modules Figure 104: Removing the protective cap Upgrade and Maintenance Manual...
  • Page 189 Expansion cards and backup units ▶ Remove the SFP+ transceiver module from its protective packaging. ▶ Remove the protective cap from the new/additional SFP+ transceiver module. CAUTION ▶ Always keep the protective caps attached to the SFP+ transceiver modules and fiber-optic cable connectors until you are ready to make a connection.
  • Page 190 Expansion cards and backup units Figure 106: Inserting the SFP+ transceiver module ▶ Insert and slide the SFP+ transceiver module into the socket connector as far as it will go. If only one slot is equipped with a SFP+ transceiver module, use the left connector as shown.
  • Page 191 Expansion cards and backup units Figure 107: Latching the locking bail ▶ Carefully fold up and latch the locking bail. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 192 Expansion cards and backup units Figure 108: Installing the protective cap ▶ If the SFP+ transceiver module is not immediately connected to an LC connector, attach the protective cap to the SFP+ transceiver module. Upgrade and Maintenance Manual RX1330 M4...

  • Page 193: Removing Sfp+ Transceiver Modules

    Expansion cards and backup units Figure 109: Installing the secondary SFP+ transceiver module ▶ If applicable, install the secondary SFP+ transceiver module accordingly. 9.4.2 Removing SFP+ transceiver modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less A network adapter is equipped with one or two SFP+ (small form-factor pluggable) transceiver modules.
  • Page 194 Expansion cards and backup units Removing an SFP+ transceiver module Figure 110: Removing the protective cap ▶ If present, remove the protective cap from the SFP+ transceiver module. CAUTION ▶ Keep the protective cap for future use. Upgrade and Maintenance Manual RX1330 M4...
  • Page 195 Expansion cards and backup units Figure 111: Unlatching the locking bail ▶ Carefully unlatch and fold down the locking bail on the SFP+ transceiver module to eject the transceiver from the socket connector. RX1330 M4 Upgrade and Maintenance Manual...

  • Page 196: Expansion Cards And Riser Cards

    Expansion cards and backup units Figure 112: Removing the SFP+ transceiver module ▶ Pull the SFP+ transceiver module out of its socket connector. ▶ Attach the protective cap to the SFP+ transceiver module. Place the removed SFP+ transceiver module in an antistatic bag or other protective environment.
  • Page 197 Expansion cards and backup units Preliminary steps ▶ "Suspending BitLocker functionality" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ Remove the corresponding riser module, see "Removing a riser module"...
  • Page 198 Expansion cards and backup units Installing the expansion card ▶ Read the documentation supplied with the expansion card. ▶ If applicable, attach the required slot bracket to the expansion card, see "Installing a slot bracket" on page 186. Figure 114: Installing the expansion card - example riser module 1 ▶...
  • Page 199 Expansion cards and backup units Example PRAID CP400i Figure 115: PRAID CP400i in riser module 1 ▶ Install the PRAID CP400i in the corresponding riser module. ▶ Connect the corresponding SAS/SATA cables to the PRAID CP400i. ▶ Connect the SAS/SATA cables to the corresponding HDD backplane. For the cable plans, see "Appendix B"...
  • Page 200 Expansion cards and backup units Example PRAID EP5x0i Figure 116: PRAID EP5x0i - Connecting cables ▶ If applicable, connect the corresponding FBU cable (1) and HDD LED cable (2) to the PRAID EP5x0i. ▶ Install the PRAID EP5x0i in the corresponding riser module. Upgrade and Maintenance Manual RX1330 M4...
  • Page 201 Expansion cards and backup units Figure 117: Example - PRAID EP5x0i in riser module 1 ▶ Connect the corresponding SAS/SATA cables or Oculink cables to the PRAID EP5x0i. ▶ Connect the HDD LED cable to connector "HDD LED" on the system board (see circle).
  • Page 202 Expansion cards and backup units Figure 118: Example - PRAID EP5x0i in riser module 1 and riser module 3 ▶ Connect the following cables: 1 SAS/SATA cable, is routed to top side and left side 4x 2.5-inch HDD backplane 2 Oculink cable (green/black), is routed to bottom side and right side 4x 2.5-inch PCIe SSD backplane 3 Oculink cable (yellow/red), is routed to bottom side and right side 4x 2.5-inch PCIe SSD backplane...

  • Page 203: Removing An Expansion Card

    Expansion cards and backup units For the cable plan, see "Appendix B" on page 365. Concluding steps ▶ Install the corresponding riser module, see "Installing a riser module" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶...
  • Page 204 Expansion cards and backup units Figure 119: Removing the expansion card - example riser module 1 ▶ Pull out the expansion card from the riser card slot. Installing the slot cover Figure 120: Installing the slot cover - example riser module 1 ▶...

  • Page 205: Replacing An Expansion Card

    Expansion cards and backup units Concluding steps ▶ Install the corresponding riser module, see "Installing a riser module" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Resuming BitLocker functionality" on page 9.5.3 Replacing an expansion card Upgrade and Repair Unit...
  • Page 206 Expansion cards and backup units ▶ If applicable, disconnect external cables to the expansion card. ▶ "Getting access to the component" on page ▶ "Locating the defective component" on page ▶ Remove the corresponding riser module, see "Removing a riser module" on page Removing the defective expansion card ▶...

  • Page 207: Replacing A Riser Card

    Expansion cards and backup units ▶ Inform the customer about changed WWN, MAC and SAS addresses, see "Looking for MAC/WWN/GUID and SAS addresses" on page ▶ "Updating the NIC configuration file in a Linux and VMware environment" on page ▶ "Updating expansion card firmware"...
  • Page 208 Expansion cards and backup units Removing the riser card ▶ Remove the expansion card, see "Removing an expansion card" on page 203. Figure 121: Removing the riser card - example riser module 1 ▶ Remove the two screws (1). ▶ Remove the riser card (2). Installing the riser card Figure 122: Installing the riser card - example riser module 1 ▶...

  • Page 209: Replacing A Tfm

    Expansion cards and backup units Concluding steps ▶ Install the corresponding riser module, see "Installing a riser module" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page 9.5.5 Replacing a TFM Upgrade and Repair Unit Hardware: 10 minutes (URU)
  • Page 210 Expansion cards and backup units Example RAID controller Figure 123: Disconnecting the FBU adapter cable from the TFM ▶ Disconnect the FBU adapter cable from the TFM. Upgrade and Maintenance Manual RX1330 M4...
  • Page 211 Expansion cards and backup units Figure 124: Removing the TFM ▶ Remove the two screws (1). ▶ Remove the TFM (2). Note for replacing the TFM: The two spacer bolts can remain on the RAID controller. Installing the new TFM Example RAID controller RX1330 M4 Upgrade and Maintenance Manual...
  • Page 212 Expansion cards and backup units Figure 125: Installing the TFM (A) ▶ If no TFM has been installed before: fit the two spacer bolts on the RAID controller. Upgrade and Maintenance Manual RX1330 M4...
  • Page 213 Expansion cards and backup units Figure 126: Installing the TFM (B) ▶ Fasten the TFM on the RAID controller with the two screws from the TFM kit. Figure 127: Connecting the FBU adapter cable RX1330 M4 Upgrade and Maintenance Manual...

  • Page 214: Upgrading To The Full Height Riser Module

    Expansion cards and backup units ▶ Connect the FBU adapter cable to the TFM. ▶ Install the RAID controller, see "Installing an expansion card" on page 196. Concluding steps ▶ "Reassembling" on page ▶ If applicable, connect external cables to the expansion card. ▶...
  • Page 215 Expansion cards and backup units Preliminary steps ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ Remove the riser module 2 and the riser module 3, see "Removing a riser module"...
  • Page 216 Expansion cards and backup units Figure 130: Installing the riser card - example full height riser module ▶ Insert the riser card (1). ▶ Fasten the riser card with two screws (2). ▶ If applicable, install a full height slot bracket to the expansion card, see "Installing a slot bracket"...
  • Page 217 Expansion cards and backup units Figure 132: Installing the extension bracket ▶ Fasten the extension bracket with one screw to the full height riser module (see circle). Figure 133: Installing the full height riser module RX1330 M4 Upgrade and Maintenance Manual...

  • Page 218: Flash Backup Unit (Fbu)

    Expansion cards and backup units ▶ Insert the riser card into the system board slot and press down the green touch points (see circles). CAUTION Valid for the full height riser module: ▶ Make sure that the EMC springs make contact correctly (see close-ups).

  • Page 219: Installing An Fbu

    Expansion cards and backup units Figure 134: Position of the shoulder screw caps FBU 1 FBU 2 9.6.2 Installing an FBU Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: Phillips PH1 / (+) No.1 screw driver (for installing the TFM) Preliminary steps ▶...
  • Page 220 Expansion cards and backup units Preparing the FBU Figure 135: Installing the FBU in the holder ▶ At a slight angle, fit the FBU under both retaining brackets of the holder. The direction of the cable is different for the FBU345. For the FBU345 the cable is on the upper side, see "FBU345 in the holder"...
  • Page 221 Expansion cards and backup units Figure 136: FBU in the holder Figure 137: FBU345 in the holder ▶ Ensure that the FBU is properly seated in the holder as shown. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 222 Expansion cards and backup units Figure 138: Connecting the FBU adapter cable to the FBU ▶ Connect the FBU cable to the corresponding FBU adapter cable. Upgrade and Maintenance Manual RX1330 M4...
  • Page 223 Expansion cards and backup units Installing the FBU Figure 139: Installing the FBU with the holder RX1330 M4 Upgrade and Maintenance Manual...
  • Page 224 Expansion cards and backup units Figure 140: Installing the FBU345 with the holder ▶ Insert the holder into the chassis so that the three shoulder screw caps on the chassis floor rest in the wide ends of the keyhole slots on the holder. ▶...
  • Page 225 Expansion cards and backup units Figure 141: Example - second FBU345 ▶ Install the second FBU. Ensure that no cables are damaged. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 226 Expansion cards and backup units Figure 142: Example - routing FBU345 adapter cables ▶ Connect the FBU345 adapter cables: 1 FBU345 adapter cable, is routed through the recess on top side and RAID controller in riser module 3 2 FBU345 adapter cable, is routed to bottom side and RAID controller in riser module 1 Concluding steps ▶...

  • Page 227: Removing An Fbu

    Expansion cards and backup units 9.6.3 Removing an FBU Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: tool-less CAUTION ▶ Dispose of used battery properly. Keep away from children. ▶ Do not throw flash backup units into the trash can. Batteries must be disposed of in accordance with local regulations concerning special waste.
  • Page 228 Expansion cards and backup units Removing the FBU with the holder Figure 143: Removing the FBU with the holder ▶ Lift up the green locking handle on the holder (see circle) while sliding the holder in direction of the arrow as far as it will go. After that, the shoulder screw caps on the chassis floor will rest in the wide ends of the keyhole slots on the holder.
  • Page 229 Expansion cards and backup units Disconnecting the FBU cable from the FBU Figure 144: Disconnecting the FBU cable from the FBU ▶ Disconnect the FBU cable from the FBU. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 230 Expansion cards and backup units Removing the FBU from the holder Figure 145: Removing the FBU from the holder ▶ Pull the FBU at a slight angle out of the holder. Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶...

  • Page 231: Replacing An Fbu

    Expansion cards and backup units 9.6.4 Replacing an FBU Upgrade and Repair Unit Hardware: 15 minutes (URU) Tools: tool-less CAUTION ▶ Dispose of used battery properly. Keep away from children. ▶ Do not throw flash backup units into the trash can. Batteries must be disposed of in accordance with local regulations concerning special waste.
  • Page 232 Expansion cards and backup units Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Updating expansion card firmware" on page Upgrade and Maintenance Manual RX1330 M4...

  • Page 233: Main Memory

    Main memory 10.1 Safety notes CAUTION ▶ Before removing several memory modules, make sure that all memory modules can be reinstalled into their original slots. Otherwise, data may be lost. ▶ Do not install unsupported third party memory modules. For more information on supported memory modules, see "Basic informations "...

  • Page 234: Basic Informations

    Main memory 10.2 Basic informations FAN5 USB 3.1 Gen 2 USB 3.1 Gen 2 FAN4 Intel C246 SERIAL SSD1 SSD2 FAN3 HDD LED DIMM 2A Slot 2 DIMM 1A DIMM 2B Slot 1 FAN2 DIMM 1B LAN 1 INDICATE Intel i210 USB 1 SATA...

  • Page 235: Installing Memory Modules

    Main memory Channel A Channel B No. of Slot ID = 2A Slot ID = 1A Slot ID = 2B Slot ID = 1B DIMMS Table 3: Mounting order Modes of operation – The maximum performance can be achieved in a symmetric dual-channel configuration.
  • Page 236 Main memory Preliminary steps ▶ "Suspending BitLocker functionality" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the air duct" on page Selecting the memory slot ▶...
  • Page 237 Main memory ▶ Align the notch on the bottom of the module with the crossbar in the slot. ▶ Press down on the memory module until the securing clips snap into the cutouts at each end of the module. Figure 149: Correct position of securing clips To improve the contact of the memory module perform the following steps: ▶...
  • Page 238 Main memory ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Updating or recovering the BIOS and iRMC S5" on page ▶ "Resuming BitLocker functionality" on page 10.4 Removing memory modules Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools:...
  • Page 239 Main memory Figure 151: Removing memory modules (B) ▶ Remove the ejected memory module. Concluding steps ▶ "Installing the air duct" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶...
  • Page 240 Main memory ▶ "Removing the air duct" on page ▶ "Locating the defective component" on page Removing the defective memory module ▶ Remove the memory module, see "Removing memory modules" on page 238. Installing the new memory module ▶ Install the memory module, see "Installing memory modules"...
  • Page 241 – one Intel® Xeon® CPU E21xx or E22xx or Pentium or Core i3, up to 95 W, up to 8 cores – one CPU socket LGA 1151 For system relevant information, see the hardware configurator of your server available online at the following address: httpss://ts.fujitsu.com/products/standard_servers/index.htm For Japan: https://www.fujitsu.com/jp/products/computing/servers/primergy/ RX1330 M4 Upgrade and Maintenance Manual...
  • Page 242 Processor (CPU) Depending on ATD support, there are different heat sinks available. 4x3,5" 4x / 8x 2,5" ATD35 ATD40 ATD45 Coffee Lake-S (LGA1151) Heatsink Heatsink Heatsink Xeon E-21xx (without Graphics) B1034-V1 FFB0412EN B1034-V2 FFB0412EN B1034-V2 GFM0412SS Xeon E-2124 4C/4T 3.3GHz 8MB 2666MHz Turbo 71W B1034-V1 FFB0412EN B1034-V2 FFB0412EN B1034-V2 GFM0412SS Xeon E-2134 4C/8T 3.5GHz 8MB 2666MHz Turbo 71W B1034-V1 FFB0412EN B1034-V2 FFB0412EN B1034-V2 GFM0412SS...
  • Page 243 Processor (CPU) 10x2,5" ATD35 ATD40 ATD45 Coffee Lake-S (LGA1151) Heatsink Heatsink Heatsink Xeon E-21xx (without Graphics) B1034-V2 FFB0412EN B1034-V2 GFM0412SS Xeon E-2124 4C/4T 3.3GHz 8MB 2666MHz Turbo 71W B1034-V2 FFB0412EN B1034-V2 GFM0412SS Xeon E-2134 4C/8T 3.5GHz 8MB 2666MHz Turbo 71W B1034-V2 FFB0412EN B1034-V2 GFM0412SS Xeon E-2136 6C/12T 3.3GHz 12MB 2666MHz Turbo 80W Xeon E-21xxG (with Graphics)
  • Page 244 Processor (CPU) CAUTION CPUs are extremely sensitive to electrostatic discharge and therefore must always be handled with care. ▶ After a CPU has been removed from its protective sleeve or from its socket, place it upside down on a nonconducting, antistatic surface. ▶...
  • Page 245 Processor (CPU) Removing the heat sink Figure 154: Removing the heat sink ▶ Loosen the four screws on the heat sink in a crossover pattern according to the numbering (1-4). ▶ Carefully twist the heat sink to detach it from the CPU. This may be necessary due to the adhesive quality of the thermal paste located between the heat sink and CPU.
  • Page 246 Processor (CPU) Removing the CPU Figure 155: Unlatching the socket release lever ▶ Unlatch the socket release lever by pushing it down and away from the socket (1). ▶ Fold back the socket release lever (2). Figure 156: Removing the CPU ▶...
  • Page 247 Processor (CPU) CAUTION ▶ Be careful not to touch or bend the spring contacts on the CPU socket. Installing the CPU ▶ Confirm that the CPU model number printed on the top of the CPU fits with the requirements. ▶ If applicable, remove the protective cap from the bottom side of the CPU. Figure 157: Installing the CPU ▶...
  • Page 248 Processor (CPU) Figure 158: Closing the load plate (A) ▶ Lower the load plate over the CPU while leaving the socket release lever in its open position. Figure 159: Closing the load plate (B) ▶ Lower the socket release lever while making sure that the front edge of the load plate slides under the shoulder screw cap (see close-up) as the lever is lowered.
  • Page 249 Processor (CPU) Figure 160: Latching the socket release lever ▶ Latch the socket release lever under the load plate tab. Applying thermal paste to the CPU surface For Japan, the service engineer must follow the instruction provided separately. If the CPU upgrade or replacement kit contains a new heat sink, a thin layer of thermal compound has already been pre-applied to its lower surface.
  • Page 250 Processor (CPU) Figure 161: Thermal paste syringe One thermal compound syringe (FSP:P304000004) contains thermal paste for three CPUs. In order to determine the correct amount of thermal paste (equal to 1.0 gram), divide the grey area of the syringe up into three equal segments. Add graduation marks to the syringe using a permanent marker to help you apply the thermal paste.
  • Page 251 Processor (CPU) Figure 162: Applying the thermal paste ▶ Apply a small point-shaped amount of thermal paste (1.0 gram, see description above) to the center of the CPU surface as shown. CAUTION ▶ Do not mix different types of thermal paste. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 252 Processor (CPU) Installing the heat sink Figure 163: Installing the heat sink ▶ Ensure that the heat sink cooling fins match the direction of the airflow! ▶ Carefully seat the heat sink on the four threaded holes as shown. CAUTION ▶...
  • Page 253 Processor (CPU) ▶ "Switching on the server" on page When the system is powered on after a CPU has been replaced or upgraded, the Global Error indicator will start flashing with the message CPU has been changed. This only indicates that the CPU configuration has been altered. There is no technical problem.
  • Page 254 Processor (CPU) Preliminary steps ▶ "Locating the defective server" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the air duct" on page Removing the defective heat sink ▶...
  • Page 255 Accessible drives 12.1 Safety notes CAUTION ▶ Before installing an accessible drive, acquaint yourself with the drive's user documentation. ▶ When inserting an accessible drive into the server, ensure not to pinch or strain any connected cables. ▶ When installing an accessible drive, hold it by its sides. Applying force to the top of the casing may cause failures.
  • Page 256 Accessible drives 3.5-inch HDD configuration Figure 164: Position of the ODD bay - example 3.5-inch HDD configuration Figure 165: Routing ODD cables - example 3.5-inch HDD configuration Blue line shows routing of ODD data cable. Red line shows routing of ODD power cable. 2.5-inch HDD configuration Figure 166: Position of the ODD bay - example 2.5-inch HDD configuration Upgrade and Maintenance Manual...
  • Page 257 Accessible drives Figure 167: Routing ODD cables - example 2.5-inch HDD configuration Blue line shows routing of ODD data cable. Red line shows routing of ODD power cable. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 258 Accessible drives 12.3 Optical disk drive (ODD) 12.3.1 Installing the ODD Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: Phillips PH1 / (+) No. 1 screw driver Preliminary steps ▶ "Suspending BitLocker functionality" on page ▶ "Shutting down the server" on page ▶...
  • Page 259 Accessible drives CAUTION ▶ Keep the dummy cover for future use. ▶ If you remove the accessible drive again and do not replace it with a new one, the dummy cover must be reinstalled to comply with EMC regulations and to satisfy cooling requirements and fire protection measures.
  • Page 260 Accessible drives Figure 170: Installing the ODD latch on the ODD ▶ Fasten the ODD latch with two screws to the rear side of the ODD (see circles). Figure 171: Installing the ODD ▶ Push the ODD into the bay (1) simultaneously pressing the front of the ODD slightly down until the ODD latch engages (2).
  • Page 261 Accessible drives Figure 172: Connecting cables (example with 2nd 2.5-inch HDD backplane) Figure 173: Connecting cables (example without 2nd 2.5-inch HDD backplane) ▶ Connect the ODD power cable (1) to the ODD. ▶ Connect the SATA cable (2) to the ODD. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 262 Accessible drives The ODD power cable and the SATA cable are preinstalled. Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Resuming BitLocker functionality" on page 12.3.2 Removing the ODD Field Replaceable Unit Hardware: 5 minutes (FRU)
  • Page 263 Accessible drives Removing the ODD Figure 174: Disconnecting cables (example with 2nd 2.5-inch HDD backplane) Figure 175: Disconnecting cables (example without 2nd 2.5-inch HDD backplane) ▶ Disconnect the ODD power cable and the SATA cable from the ODD. RX1330 M4 Upgrade and Maintenance Manual...
  • Page 264 Accessible drives Figure 176: Removing the ODD ▶ Press the ODD latch in direction of the arrow until it disengages (1). ▶ Pull the ODD out of the bay (2). Figure 177: Removing the ODD latch from the ODD ▶ Remove the two screws (see circles). ▶...
  • Page 265 Accessible drives Installing the dummy cover Figure 178: Installing the dummy cover ▶ Push the dummy cover inward until it engages at the right side. Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶...
  • Page 266 Accessible drives ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page Removing the defective ODD ▶ Remove the ODD, see "Removing the ODD" on page 262. Installing the new ODD ▶...
  • Page 267 Front panel 13.1 Safety notes CAUTION ▶ When inserting the front panel module into the server, ensure not to pinch or strain any connected cables. ▶ Circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity. Always discharge static build-up (e.g.
  • Page 268 Front panel 13.3 Front panel module 13.3.1 Replacing the front panel module Field Replaceable Unit Hardware: 10 minutes (FRU) Software: 5 minutes Tools: – Phillips PH1 / (+) No. 1 screw driver – Phillips PH2 / (+) No. 2 screw driver –...
  • Page 269 Front panel ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the air duct" on page Removing the front panel module Figure 179: Disconnecting the cables (A) ▶ Disconnect the front USB cable (1) and the front panel cable (2) from the system board.
  • Page 270 Front panel Figure 181: Removing the front panel module ▶ Remove the two screws (1). ▶ Pull the front panel module out of its bay (2) until the holder is completely accessible. Figure 182: Removing cables from the front panel module ▶...
  • Page 271 Front panel Do not cut the cable tie. ▶ Remove the two corresponding screws and disconnect the front USB cable (2). ▶ If applicable, open the cable tie and disconnect the front VGA cable (3). Do not cut the cable tie. ▶...
  • Page 272 Front panel ▶ If applicable, connect the front VGA cable to the front VGA board and secure it with the cable tie (3). Figure 184: Installing the front panel module ▶ Push the front panel module in its bay (1). ▶...
  • Page 273 Front panel Figure 186: Connecting the cables (B) ▶ If applicable, connect the front VGA cable (black) to the system board. Concluding steps ▶ "Installing the air duct" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶...
  • Page 274 Front panel Preliminary steps ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the front panel module" on page 269. Removing the dummy cover Figure 187: Removing the dummy cover ▶...
  • Page 275 Front panel Installing the front VGA board Figure 188: Installing the front VGA board ▶ Push the front VGA connector in the corresponding recess (1) and fasten the front VGA board with two screws (2). ▶ Route the cable tie under the front VGA board (3). Concluding steps ▶...
  • Page 276 Front panel Preliminary steps ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the front panel module" on page 269. Removing the front VGA board Figure 189: Removing the front VGA board ▶...
  • Page 277 Front panel ▶ "Switching on the server" on page 13.4.3 Replacing the front VGA board Upgrade and Repair Unit Hardware: 10 minutes (URU) Tools: Phillips PH1 / (+) No. 1 screw driver Preliminary steps ▶ "Locating the defective server" on page ▶...
  • Page 278 Front panel 13.5 Front panel on QRL (10x 2.5-inch HDD) 13.5.1 Replacing the front panel on QRL Field Replaceable Unit Hardware: 10 minutes (FRU) Software: 5 minutes Tools: Phillips PH1 / (+) No. 1 screw driver Note on system information backup/restore The front panel (front panel module, front panel board or front panel on QRL) contains the Chassis ID EPROM that contains system information like server name and model, housing type, serial number and manufacturing data.
  • Page 279 Front panel Removing the front panel on QRL The front panel on QRL and the front panel cable are combined in one spare part. Figure 190: Disconnecting the front panel cable ▶ Pull up the locking bar (1). ▶ Remove the front panel cable (2). ▶...
  • Page 280 Front panel Figure 191: Removing the front panel on QRL (A) ▶ Remove the two screws (see circles). Figure 192: Removing the front panel on QRL (B) ▶ Remove the front panel. ▶ Pull the front panel cable out of the opening. Upgrade and Maintenance Manual RX1330 M4...
  • Page 281 Front panel Installing the front panel on QRL Figure 193: Installing the front panel (A) ▶ Thread the front panel cable through the opening. Figure 194: Installing the front panel (B) ▶ Position the front panel on the ear. ▶ Fasten the front panel with two screws (see Figure 191).
  • Page 282 Front panel Figure 195: Connecting the front panel cable ▶ Pull up the locking bar (1). ▶ Bend the cable 90 degrees by hand for easier routing. ▶ Insert the front panel cable (2). Please make sure that the front panel cable is assembled as shown (blue marking).
  • Page 283 Serial interface 14.1 Safety notes CAUTION ▶ For more information, see "Important information" on page 14.2 Installing the serial interface Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less ① ② Figure 196: Serial interface kit Long slot bracket Serial interface with short slot bracket The long slot bracket is not used in this server.
  • Page 284 Serial interface Preliminary steps ▶ "Suspending BitLocker functionality" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page Removing the slot cover ▶ Remove the corresponding riser module, see "Removing a riser module"...
  • Page 285 Serial interface Figure 198: Connecting the serial interface cable ▶ Connect the serial interface cable to the system board connector "SERIAL". Figure 199: Installing riser module RX1330 M4 Upgrade and Maintenance Manual...
  • Page 286 Serial interface ▶ Install the corresponding riser module, see "Installing a riser module" on page Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶ "Resuming BitLocker functionality" on page 14.3 Removing the serial interface Upgrade and Repair Unit...
  • Page 287 Serial interface Figure 200: Disconnecting the serial interface cable ▶ Disconnect the serial interface cable from the system board connector "SERIAL". Figure 201: Removing the serial interface - example riser module 2 RX1330 M4 Upgrade and Maintenance Manual...
  • Page 288 Serial interface ▶ Remove the serial interface. Installing the slot cover ▶ Install the corresponding slot cover, see "Installing the slot cover" on page 204. ▶ Install the corresponding riser module, see "Installing a riser module" on page Concluding steps ▶...
  • Page 289 Serial interface Installing the new serial interface ▶ Install the serial interface, see "Installing the serial interface" on page 283. Concluding steps ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page ▶...
  • Page 290 Serial interface Upgrade and Maintenance Manual RX1330 M4...
  • Page 291 System board and components 15.1 Safety notes CAUTION ▶ Devices and components inside the server remain hot after shutdown. After shutting down the server, wait for hot components to cool down before installing or removing internal options. ▶ Circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity.
  • Page 292 System board and components ● iRMC microSD card The iRMC microSD card is necessary for using the embedded Lifecycle Management (eLCM) functionality of the iRMC. ● M.2 SSD The system board offers two M.2 slots (Key M) with support for 42 mm, 60 mm, 80 mm and 110 mm long M.2 SSDs.
  • Page 293 System board and components Note on BIOS settings recovery When replacing the CMOS battery, the BIOS settings will be reset. Ensure to note down your current BIOS settings including "System Time" and "System date" before replacing the CMOS battery. Preliminary steps ▶...
  • Page 294 System board and components ▶ Press the locking spring into direction of the arrow (1), so that the CMOS battery jumps out of its socket. ▶ Remove the CMOS battery (2). CAUTION Sharp tools such as screw drivers might damage system board components in case of slipping.
  • Page 295 System board and components 15.4 Trusted Platform Module (TPM) 15.4.1 TPM kit Figure 203: TPM installation kit Special screw for TPM TPM spacer TPM bit insert for TPM special screw 15.4.2 Position of the TPM Reset PWR MAIN Slot 3 Front Panel1 PC98 Front USB...
  • Page 296 System board and components 15.4.3 Installing the TPM Field Replaceable Unit Hardware: 5 minutes (FRU) Software: 5 minutes Tools: – Bit screw driver – TPM bit insert For Japan: – TPM module fixing tool (S26361-F3552-L909) Preliminary steps ▶ "Suspending BitLocker functionality" on page ▶...
  • Page 297 System board and components Figure 206: Inserting the TPM spacer on the system board ▶ Insert the TPM spacer into the hole on the system board. Figure 207: TPM bit insert ▶ Attach the TPM bit insert or TPM module fixing tool (for Japan) to a bit screw driver.
  • Page 298 System board and components Figure 208: Installing the TPM ▶ Connect the TPM to the system board (1). ▶ Fasten the TPM with the special screw for the TPM using the TPM bit insert or TPM module fixing tool (Japan) (2). CAUTION ▶...
  • Page 299 System board and components ▶ As soon as the startup screen appears, press the [F2] function key to enter the BIOS setup menu. ▶ Select the Advanced menu. ▶ Select the Trusted Computing submenu. ▶ Set the TPM Support and TPM State settings to Enabled. ▶...
  • Page 300 Decrypting the volume may be time-consuming. By decrypting the volume, all of the information stored on that computer is decrypted. For more information on how to disable BitLocker drive encryption, see the Microsoft Knowledge Base. See the Fujitsu web pages for more details. Upgrade and Maintenance Manual...
  • Page 301 System board and components Disabling the TPM in the system board BIOS Proceed as follows: ▶ Switch on or restart your server. ▶ As soon as the startup screen appears, press the [F2] function key to enter the BIOS setup menu. ▶...
  • Page 302 System board and components Figure 209: Removing the TPM screw ▶ Locate the slotted lower end of the TPM screw (1). ▶ Carefully loosen the TPM screw using a thin slotted screw driver (e. g. watchmaker's screw driver) or the dedicated TPM screw driver (Japan) (2). CAUTION ▶...
  • Page 303 System board and components Figure 210: Removing the TPM spacer ▶ Using a flat nose pliers, press together the hooks on the TPM spacer (1, see close-up) and remove it from the system board (2). If the TPM is to be replaced, the TPM spacer may remain on the system board.
  • Page 304 System board and components Tools: Removing the system board: – Phillips PH2 / (+) No. 2 screw driver Replacing the TPM: – Bit screw driver – TPM bit insert – thin slotted screw driver (2 x 0.4 mm) For Japan: –...
  • Page 305 System board and components Installing the new TPM The TPM spacer is already present on the system board. ▶ Install the TPM, see "Installing the TPM" on page 296. Concluding steps ▶ "Installing the air duct" on page ▶ "Reassembling" on page ▶...
  • Page 306 System board and components Tools: tool-less Preliminary steps ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the air duct" on page ▶ Remove the riser module 1, see "Removing a riser module"...
  • Page 307 System board and components ▶ With the label facing up, insert the iRMC microSD card into the microSD card slot (1) until it locks in place (2). The onboard position of the microSD card slot can be found in "Connectors and indicators on the system board" on page 342.
  • Page 308 System board and components Removing the iRMC microSD card Figure 213: Removing the iRMC microSD card ▶ To eject the iRMC microSD card, gently push it in and then let go (1). ▶ Pull the iRMC microSD card straight out of its slot (2). CAUTION (not valid for Europe, Middle East, India and Africa) The iRMC microSD card contains customer information.
  • Page 309 System board and components 15.5.4 Replacing the iRMC microSD card Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools: tool-less Preliminary steps ▶ "Locating the defective server" on page ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶...
  • Page 310 System board and components Concluding steps ▶ Install the riser module 1, see "Installing a riser module" on page ▶ "Installing the air duct" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page 15.6 M.2 SSD 15.6.1...
  • Page 311 System board and components Installing the M.2 SSD Figure 214: Example M.2 SSD Figure 215: Slots for M.2 SSDs M.2 slot 1 M.2 slot 2 RX1330 M4 Upgrade and Maintenance Manual...
  • Page 312 System board and components CAUTION An M.2 SSD in M.2 slot 2 is not recognized, if M.2 slot 1 is free. ▶ The M.2 slot 1 must be equipped first. Each M.2 SSD needs one hexagon standoff for fastening. To support different length of M.2 SSD, several nuts are on the system board indicating the positions for fastening the M.2 SSD.
  • Page 313 System board and components Figure 217: Fastening the M.2 SSD ▶ Fasten the M.2 SSD with the screw (see circle). Concluding steps ▶ If applicable, install riser modules 2 and 3, see "Installing a riser module" on page ▶ "Reassembling" on page ▶...
  • Page 314 For Japan In order to setup the ESXi, see the corresponding version of the "VMware vSphere Software Description" from the following URL and reinstall ESXi to the M.2 SSD. https://jp.fujitsu.com/platform/server/primergy/software/vmware/manual/ 15.6.2 Removing an M.2 SSD Upgrade and Repair Unit Hardware: 5 minutes...
  • Page 315 System board and components ▶ If applicable, remove riser modules 2 and 3, see "Removing a riser module" on page Removing the M.2 SSD Figure 218: Removing the M.2 SSD (A) ▶ Remove the screw (see circle). Figure 219: Removing the M.2 SSD (B) ▶...
  • Page 316 System board and components Concluding steps ▶ If applicable, install riser modules 2 and 3, see "Installing a riser module" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page 15.6.3 Replacing an M.2 SSD Upgrade and Repair Unit...
  • Page 317 System board and components ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page Software configuration To install the ESXi to the M.2 SSD, see "Software configuration" on page 313. 15.7 Dual microSD 64GB Enterprise 15.7.1 Installing the Dual microSD 64GB Enterprise Upgrade and Repair Unit Hardware: 5 minutes...
  • Page 318 System board and components Installing the Dual microSD 64GB Enterprise DIMM 2B Slot 1 FAN2 DIMM 1B LAN 1 INDICATE Intel i210 USB 1 SATA SATA Shared LAN 2 LAN 1 iRMC Intel RCVR i210 PWD CLR FAN1 Management Micro Service PWR4 Figure 220: Position on the system board...
  • Page 319 System board and components Figure 222: Installing the Dual microSD 64GB Enterprise ▶ Insert the Dual microSD 64GB Enterprise into the system board connector "Internal USB 3.0" on the system board. ▶ Connect the cable to the connector "ROC" on the system board. Concluding steps ▶...
  • Page 320 System board and components Tools: tool-less Preliminary steps ▶ "Shutting down the server" on page ▶ "Disconnecting the power cord" on page ▶ "Getting access to the component" on page ▶ "Removing the air duct" on page Removing the Dual microSD 64GB Enterprise Figure 223: Removing the Dual microSD 64GB Enterprise ▶...
  • Page 321 System board and components Concluding steps ▶ "Installing the air duct" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ "Switching on the server" on page 15.7.3 Replacing the Dual microSD 64GB Enterprise Upgrade and Repair Unit Hardware: 5 minutes (URU) Tools:...
  • Page 322 System board and components Replacing the Dual microSD 64GB Enterprise ▶ Remove the defective Dual microSD 64GB Enterprise, see "Removing the Dual microSD 64GB Enterprise" on page 320. ▶ Remove both microSD cards from the defective Dual microSD 64GB Enterprise. Proceed as described in the following: Figure 224: Removing the microSD card ▶...
  • Page 323 System board and components ▶ Install the new Dual microSD 64GB Enterprise, see "Installing the Dual microSD 64GB Enterprise" on page 318. Concluding steps ▶ "Installing the air duct" on page ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶...
  • Page 324 System board and components Replacing the microSD card ▶ Remove the Dual microSD 64GB Enterprise, see "Removing the Dual microSD 64GB Enterprise" on page 320. ▶ Remove the defective microSD card from the Dual microSD 64GB Enterprise. Proceed as described in the following: ▶...
  • Page 325 System board and components 15.8 System board 15.8.1 Replacing the system board Field Replaceable Unit Hardware: 40 minutes (FRU) Software: 20 minutes Tools: Replacing the system board: – Phillips PH2 / (+) No. 2 screw driver – Magnifying glass for inspecting CPU socket springs (recommended) Replacing the TPM: –...
  • Page 326 System board and components CAUTION ▶ Before replacing the system board, ask the customer whether TPM functionality is used. ▶ If the customer is using TPM functionality, remove the TPM from the old system board and install it on the new system board. ▶...
  • Page 327 System board and components When the system board is replaced, the settings in the Security tab on the BIOS setup menu are not automatically transferred, so you must manually restore the BIOS settings. The settings related to Security block all data writing in order to prevent data tampering from external sources such as applications.
  • Page 328 System board and components ▶ Remove all memory modules, see "Removing memory modules" on page 238. Before removing the memory modules, take a note on the installation slot number for each memory module. Ensure that you install the memory modules in the slot they were located before the replacement.
  • Page 329 System board and components Figure 226: System board - Position of the screws ▶ Remove the eight screws from the system board (see circles). RX1330 M4 Upgrade and Maintenance Manual...
  • Page 330 System board and components Figure 227: Removing the system board ▶ Use both hands to lift the system board carefully out of the chassis in a slight angle. Thereby you pull the connectors out of the I/O panel. CAUTION ▶ Always take the system board with both hands! ▶...
  • Page 331 System board and components ▶ Remove the protective plastic cover from the CPU socket of the new system board and fit it onto the socket of the defective system board which will be sent back to spares. Returned system boards without this cover probably have to be scrapped.
  • Page 332 System board and components ▶ Reconnect all cables to the system board: – Power cables of PSU – Front panel cable – Front USB cable (if applicable) – Power cable for HDD backplane (if applicable) – SATA cable(s) for HDD backplane (if applicable) –...
  • Page 333 System board and components ▶ "Reassembling" on page ▶ "Connecting the power cord" on page ▶ Connect all external cables. ▶ "Switching on the server" on page When the system is powered on after a CPU has been replaced or upgraded, the Global Error indicator will start flashing with the message CPU has been changed.
  • Page 334 System board and components ▶ If applicable, reconfigure your network settings in the operation system according to the original configuration of the replaced controller (expansion card or onboard). Configuration of network settings should be performed by the customer. For more information, see "Note on network settings recovery"...
  • Page 335 16.1.1 Server front 16.1.1.1 2.5-inch HDD/SSD configuration The PRIMERGY RX1330 M4 server is available as a rack model. Figure 228: Server front with up to 4x 2.5-inch HDDs/SSDs ID card ODD (option) / dummy cover Front VGA (option) / dummy cover Up to 4x 2.5-inch HDDs/SSDs...
  • Page 336 Up to 10x 2.5-inch HDDs/SSDs Front panel on QRL 16.1.1.2 3.5-inch HDD configuration The PRIMERGY RX1330 M4 server is available as a rack model. Figure 231: Server front with up to 4x 3.5-inch HDDs ODD (option) / dummy cover Front panel module ID card Up to 4x 3.5-inch HDDs...
  • Page 337 Appendix A 16.1.2.2 Server rear with hot-plug PSUs Figure 233: Server rear with hot-plug PSUs Up to 2 hot-plug PSUs PCI slot 1 / riser module 1 PCI slot 3 / riser module 3 I/O panel PCI slot 2 / riser module 2 RX1330 M4 Upgrade and Maintenance Manual...
  • Page 338 Appendix A 16.1.3 Server interior Example with 3.5-inch HDDs and hot-plug PSUs Figure 234: Server interior - 3.5-inch HDDs and hot-plug PSUs Up to 2 hot-plug PSUs / dummy cover Front panel module Main memory Up to 4x 3.5-inch HDDs / dummy Riser module 1 modules Riser module 2...
  • Page 339 Appendix A Example with 2.5-inch HDDs and standard PSU Figure 235: Server interior - 2.5-inch HDDs and standard PSU Standard PSU Front panel module Main memory Up to 8x 2.5-inch HDDs / dummy Riser module 1 modules Riser module 2 ODD (option) / dummy cover M.2 SSD Fan modules (4x)
  • Page 340 Appendix A Example with 2.5-inch HDDs/PCIe SSDs and hot-plug PSUs Figure 236: Server interior - 2.5-inch HDDs/PCIe SSDs and hot-plug PSUs Up to 2 hot-plug PSUs / dummy cover Fan modules (5x) FBU345 (2x) Front panel module Main memory ODD (option) / dummy cover Riser module 1 Up to 4x 2.5-inch HDDs and up to 4x Riser module 2...
  • Page 341 Appendix A Example with 10x 2.5-inch HDDs and hot-plug PSUs Figure 237: Server interior - 10x 2.5-inch HDDs and hot-plug PSUs Up to 2 hot-plug PSUs / dummy cover Fan modules (5x) Front panel on ear Main memory Up to 10x 2.5-inch HDDs / dummy Riser module 1 modules Riser module 2...
  • Page 342 Appendix A 16.2 Connectors and indicators 16.2.1 Connectors and indicators on the system board 16.2.1.1 System board D3675 Onboard connectors Reset PWR MAIN Front Panel1 Slot 3 PC98 Front USB USB 2.0 PWR3 PWR2 Front Panel2 PWR1 USB 2.0 FAN5 USB 3.1 Gen 2 USB 3.1...
  • Page 343 Appendix A Pos. Print Description Connector for optional TPM Front USB Front USB connector Front Panel2 Front panel connector (front panel on QRL) PWR1 PSU connector 12 V Front Panel1 Front panel connector (front panel module) PWR2 Power connector for HDD backplane PC98 PSU connector (standard PSU) PSU connector (hot-plug PSU)
  • Page 344 Appendix A Pos. Print Description M.2 SSD1 M.2 slot 1 M.2 SSD2 M.2 slot 2 SERIAL Connector for optional serial interface Onboard indicators and controls Reset PWR MAIN Slot 3 Front Panel1 PC98 Front USB USB 2.0 PWR3 PWR2 Front Panel2 PWR1 USB 2.0...
  • Page 345 Appendix A If the server has been powered off (power plugs must be disconnected) it is possible to indicate the faulty component by pressing the indicate CSS button. The LEDs have the following meaning: Indicator Status Description The server has been highlighted using Identification ServerView Operations Manager, iRMC S5 blue on...
  • Page 346 Appendix A Indicator Status Description G - Memory Memory module running orange on Memory module failure H - iRMC iRMC S5 inactive flashing green iRMC S5 okay I - Fan System fan running orange on System fan failure K - Standby orange on All standby voltages OK Power...
  • Page 347 Appendix A Figure 241: Indicators on the front panel on QRL ID indicator HDD/SSD activity indicator CSS indicator Power-on indicator Global Error indicator AC connected indicator ID indicator (1) See also "iRMC-related status signals" on page 349. Status Description blue on The server has been highlighted using ServerView Operations Manager, iRMC web interface or the ID button on the front panel for easy identification.
  • Page 348 Appendix A Status Description flashing orange CSS component failure detected. Global Error indicator (3) See also "iRMC-related status signals" on page 349. Status Description No critical event detected (non-CSS component). orange on Prefailure event detected (non-CSS component). flashing orange Non-CSS component failure detected. Possible causes: –...
  • Page 349 An emergency flash of the iRMC firmware is in progress. For more information about the iRMC flash procedure, see "Basic software procedures" in the "FUJITSU Server PRIMERGY RX1330 M4 Upgrade and Maintenance Manual". RX1330 M4 Upgrade and Maintenance Manual...
  • Page 350 Appendix A HDD prefailure detection Depending on your hardware configuration HDD prefailure detection will be supported. The requirements are: – iRMC S5 Firmware 1.2 or later – supported OOB RAID system 16.2.2.2 Indicator on the ODD ODDs may have an indicator or not. Figure 242: Indicator on the ODD (example) Activity indicator Activity indicator (1)
  • Page 351 Appendix A 16.2.2.3 Indicators on the hot-plug HDD/SSD module Figure 243: Indicators on the hot-plug HDD/SSD module Access indicator Error indicator Access Indicator (1) Status Description The HDD/SSD is inactive. green on The HDD/SSD being accessed. Error indicator (2) Status Description No HDD/SSD error detected.
  • Page 352 Appendix A Status Description flashing orange slowly HDD/SSD RAID rebuild is in progress. Data is being restored after replacing a drive that has been combined into a RAID array. 16.2.3 Server rear 16.2.3.1 Connectors on the server rear Figure 244: Connectors on the server rear USB 3.0 connectors (2x) Shared LAN connector (LAN2) USB 3.1 Gen 2 connectors (2x)
  • Page 353 Appendix A 16.2.3.2 ID, CSS and Global Error indicators Figure 245: Indicators on the I/O panel: ID, CSS and Global Error indicators ID indicator, CSS indicator, Global Error indicator Note on CSS and Global Error indicators on the I/O panel: If CSS and Global Error indicators are located in the same place on the I/O panel of the server, also check the indicators on the front panel to determine if a CSS or Global Error event has been detected.
  • Page 354 Appendix A CSS indicator (1) Status Description No critical event detected (CSS component). orange on Prefailure event detected (CSS component). flashing orange CSS component failure detected. Global Error indicator (1) See also "iRMC-related status signals" on page 354. Status Description No critical event detected (non-CSS component).
  • Page 355 Appendix A For more information about the iRMC flash procedure, see "Basic software procedures" in the "FUJITSU Server PRIMERGY RX1330 M4 Upgrade and Maintenance Manual". HDD prefailure detection Depending on your hardware configuration HDD prefailure detection will be supported. The requirements are: –...
  • Page 356 Appendix A LAN speed indicator (2) Status Description yellow on Data traffic at a transfer rate of 1 Gbit/s. green on Data traffic at a transfer rate of 100 Mbit/s. Data traffic at a transfer rate of 10 Mbit/s. Indication of LAN connection supporting Energy Efficient Ethernet (EEE mode) To configure the EEE mode, it is necessary that the onboard LAN or an add-in LAN card supports this mode and the connected switch supports this mode as...
  • Page 357 Appendix A 16.2.3.4 Indicator on hot-plug PSU ① Figure 247: PSU status indicator PSU status indicator PSU status indicator (1) Status Description flashing green The server is switched off, but mains voltage is present (standby mode). green on The server is switched on and operating properly. flashing orange An overload has been detected.
  • Page 358 Appendix A 16.2.3.5 Indicator on FJBU Figure 248: Indicator on FJBU FJBU status indicator FJBU status indicator (1) Status Description flashing green The battery unit is charging. flashing green The battery unit is discharging. slowly green on The battery unit is fully charged. flashing orange A battery unit failure has been detected.
  • Page 359 Appendix A 16.2.4 Acoustic indicators PEI Beep Codes Pre-EFI Initialization (PEI) - memory Initialization (bootblock) # of Description Action Beep ▶ Check if the memory module is Memory not installed installed. ▶ Check if the memory module is installed correctly. Recovery started Recovery procedure is initialized by jumper settings on the system board and...
  • Page 360 Appendix A # of Description Action Beep ▶ Check for the correct password and try Invalid password again. Make sure that the caps lock key is deactivated. No Console Input Booting will continue. devices or Output Serial console redirection is considered devices are found a console output device if enabled.
  • Page 361 Appendix A 16.3 Onboard settings HDD LED DIMM 2A Slot 2 DIMM 1A DIMM 2B Slot 1 FAN2 DIMM 1B LAN 1 INDICATE Intel i210 USB 1 SATA SATA Shared LAN 2 LAN 1 iRMC Intel RCVR i210 PWD CLR FAN1 Management Micro...
  • Page 362 Appendix A 16.4 Minimum startup configuration Field Replaceable Units (FRU) If the server does not start up or other problems occur, it may be necessary to take the system down to its most basic configuration in order to isolate the defective component.
  • Page 363 Appendix A CAUTION ▶ Since the fan module is not included in the minimum startup configuration, the server must be shut down immediately after the diagnostic process is complete (POST phase has been passed). ▶ The minimum startup configuration must be used exclusively for diagnostic purposes by maintenance personnel, never in daily operation! RX1330 M4...
  • Page 364 Appendix A Upgrade and Maintenance Manual RX1330 M4...
  • Page 365 17.1 Supplied documents The following documents are available in this appendix: ● "Cable plan for FUJITSU Server PRIMERGY RX1330 M4 Reference Manual" ● "List of Released Adapters incl. Installation sequence and priority" ● "List of all used screws for PRIMERGY Servers - Assembled in Germany and Japan"...
  • Page 366 Reference Manual - English Cable Plan for FUJITSU Server PRIMERGY RX1330 M4 Reference Manual April 2022...
  • Page 367 Cable Plan Contents List of used cables List of used cables List of used cables (continuation) List of used cables (continuation) Basic Cabling 4x3.5" Basic Cabling 4x3.5" Basic Cabling 4x2,5" and 8x2.5" Basic Cabling 4x2,5" and 8x2.5" Basic Cabling 4x PCIe SSD + 4x HDD Basic Cabling 4x PCIe SSD + 4x HDD Basic Cabling 10x2.5"...
  • Page 368 Cable Plan List of used cables Ref. Name Number Routing Basic Basic Cabling 4x3.5" CBL_FRONTPANEL_550 T26139-Y4015-V305 Basic Cabling 4x2,5" and 8x2.5" Basic Cabling 4x PCIe SSD + 4x HDD Basic Cabling 4x3.5" CBL_FRONT_USB_530 T26139-Y3999-V513 Basic Cabling 4x2,5" and 8x2.5" Basic Cabling 4x PCIe SSD + 4x HDD CBL FLEXP 22PL 600 T26139-Y4042-V2 Basic Cabling 10x2.5"...
  • Page 369 Cable Plan List of used cables (continuation) Ref. Name Number Routing Data CBL_HOST-BP_430 T26139-Y4050-V12 Data Cabling 4x PCIe SSD + 4x HDD SATA CBL_HOST-BP_530 T26139-Y4050-V13 Data Cabling 4x PCIe SSD + 4x HDD SATA Accessible drives Power Cabling 4x3.5" Std. Power Cabling 4x3.5"...
  • Page 370 Cable Plan Basic Cabling 4x3.5" System Board System Board Front Panel Front Panel PWR MAIN PWR MAIN Front Panel Front Panel PWR 1 PWR 1 USB 3.0 USB 3.0 Front VGA Front VGA PC98 PC98 PWR 2 PWR 2 PWR 3 PWR 3 FRONTPANEL 1 FRONTPANEL 1...
  • Page 371 Cable Plan Basic Cabling 4x2,5" and 8x2.5" System Board System Board Front Panel Front Panel PWR MAIN PWR MAIN Front Panel Front Panel PWR 1 PWR 1 USB 3.0 USB 3.0 Front VGA Front VGA PC98 PC98 PWR 2 PWR 2 PWR 3 PWR 3 FRONTPANEL 1...
  • Page 372 Cable Plan Basic Cabling 4x PCIe SSD + 4x HDD System Board System Board Front Panel Front Panel PWR MAIN PWR MAIN Front Panel Front Panel PWR 1 PWR 1 USB 3.0 USB 3.0 Front VGA Front VGA PC98 PC98 PWR 2 PWR 2 PWR 3...
  • Page 373 Cable Plan Basic Cabling 10x2.5" System Board System Board Front Panel on QRL Front Panel on QRL PWR MAIN PWR MAIN Front Panel Front Panel PWR 1 PWR 1 PC98 PC98 PWR 2 PWR 2 PWR 3 PWR 3 FRONTPANEL 1 FRONTPANEL 1 Front USB Front USB...
  • Page 374 Cable Plan Power Cabling 4x3.5" Std. System Board System Board Standard PSU PWR MAIN PWR MAIN PWR 1 PWR 1 PC98 PC98 PWR 2 PWR 2 PWR 3 PWR 3 FRONTPANEL 1 FRONTPANEL 1 Front USB Front USB 4x3.5" HDD 4x3.5"...
  • Page 375 Cable Plan Power Cabling 4x3.5" Red. System Board System Board Power Backplane Power Backplane A3C40206590 A3C40206590 PWR MAIN PWR MAIN PWR MAIN PWR MAIN PWR 1 PWR 1 PWR EXT PWR EXT PWR CTRL PWR CTRL PC98 PC98 PWR 1 PWR 1 PWR 2 PWR 2...
  • Page 376 Cable Plan Power Cabling 4x2.5" and 8x2.5" Std. System Board System Board Standard PSU PWR MAIN PWR MAIN PWR 1 PWR 1 PC98 PC98 PWR 2 PWR 2 4x2.5" HDD L-Shape 4x2.5" HDD L-Shape PWR 3 PWR 3 A3C40196780 A3C40196780 FRONTPANEL 1 FRONTPANEL 1 Front USB...
  • Page 377 Cable Plan Power Cabling 4x2,5" and 8x2.5" Red. System Board System Board Power Backplane Power Backplane A3C40206590 A3C40206590 PWR MAIN PWR MAIN PWR MAIN PWR MAIN PWR 1 PWR 1 PWR EXT PWR EXT PWR CTRL PWR CTRL PC98 PC98 PWR 1 PWR 1 PWR 2...
  • Page 378 Cable Plan Power Cabling 4x PCIe SSD + 4x HDD System Board System Board Power Backplane Power Backplane A3C40206590 A3C40206590 PWR MAIN PWR MAIN PWR MAIN PWR MAIN PWR 1 PWR 1 PWR EXT PWR EXT PWR CTRL PWR CTRL PC98 PC98 PWR 1...
  • Page 379 Cable Plan Power Cabling 10x2.5" Red. System Board System Board Power Backplane Power Backplane A3C40206590 A3C40206590 PWR MAIN PWR MAIN PWR MAIN PWR MAIN PWR 1 PWR 1 PWR EXT PWR EXT PWR CTRL PWR CTRL PC98 PC98 PWR 1 PWR 1 PWR 2 PWR 2...
  • Page 380 Cable Plan Data Cabling 4x3.5" System Board System Board PWR MAIN PWR MAIN PWR 1 PWR 1 PC98 PC98 SATA ODD SATA ODD PWR 2 PWR 2 PWR 3 PWR 3 Data Data Power Power FRONTPANEL 1 FRONTPANEL 1 Front USB Front USB 4x3.5"...
  • Page 381 Cable Plan Data Cabling 4x3.5" PSAS and PRAID System Board System Board SATA ODD SATA ODD Data Data Power Power 4x3.5" HDD 4x3.5" HDD A3C40157818 A3C40157818 SATA ODD SATA ODD HDD LED HDD LED SMBUS SMBUS SGPIO SGPIO Slot 1 Slot 1 MLC2 MLC2...
  • Page 382 Cable Plan Data Cabling 4x3.5" CP2100-8i System Board System Board SATA ODD SATA ODD Data Data Power Power 4x3.5" HDD 4x3.5" HDD A3C40157818 A3C40157818 SATA ODD SATA ODD HDD LED HDD LED SMBUS SMBUS SGPIO SGPIO Slot 1 Slot 1 CP2100-8i CP2100-8i RX1330 M4...
  • Page 383 Cable Plan Data Cabling 4x3.5" PRAID EP5xx System Board System Board SATA ODD SATA ODD Data Data Power Power 4x3.5" HDD 4x3.5" HDD A3C40157818 A3C40157818 SATA ODD SATA ODD SATA 0-3 SATA 0-3 HDD LED HDD LED SMBUS SMBUS J10DACT J10DACT SGPIO SGPIO...
  • Page 384 Cable Plan Data Cabling 4x2.5" System Board System Board PWR MAIN PWR MAIN PWR 1 PWR 1 PC98 PC98 PWR 2 PWR 2 PWR 3 PWR 3 FRONTPANEL 1 FRONTPANEL 1 Front USB Front USB FRONTPANEL 2 FRONTPANEL 2 USB 1 USB 1 SATA ODD SATA ODD...
  • Page 385 Cable Plan Data Cabling 4x2.5" and 8x2.5" PSAS and PRAID System Board System Board SATA ODD SATA ODD Data Data Power Power 4x2.5" HDD L-Shape 4x2.5" HDD L-Shape A3C40196780 A3C40196780 SMBUS SMBUS 4x2.5" HDD 4x2.5" HDD SATA ODD SATA ODD A3C40196777 A3C40196777 HDD LED...
  • Page 386 Cable Plan Data Cabling 4x2.5" and 8x2.5" CP2100-8i System Board System Board SATA ODD SATA ODD Data Data Power Power 4x2.5" HDD L-Shape 4x2.5" HDD L-Shape A3C40196780 A3C40196780 SMBUS SMBUS 4x2.5" HDD 4x2.5" HDD SATA ODD SATA ODD A3C40196777 A3C40196777 HDD LED HDD LED SMBUS...
  • Page 387 Cable Plan Data Cabling 4x2.5" and 8x2.5" PRAID EP5xx System Board System Board SATA ODD SATA ODD Data Data Power Power 4x2.5" HDD L-Shape 4x2.5" HDD L-Shape A3C40196780 A3C40196780 SATA ODD SATA ODD SATA 0-3 SATA 0-3 SMBUS SMBUS HDD LED HDD LED 4x2.5"...
  • Page 388 Cable Plan Data Cabling 4x PCIe SSD + 4x HDD SATA System Board System Board SATA ODD SATA ODD Data Data Power Power 4x2.5" HDD L-Shape 4x2.5" HDD L-Shape A3C40196780 A3C40196780 SATA ODD SATA ODD SMBUS SMBUS SATA 0-3 SATA 0-3 Label Label HDD LED...
  • Page 389 Cable Plan Data Cabling 4x PCIe SSD + 4x HDD SAS System Board SATA ODD SATA ODD Data Data Power Power FBU 2 SATA ODD 4x2.5" HDD L-Shape 4x2.5" HDD L-Shape HDD LED A3C40196780 A3C40196780 Label J10DACT J10DACT SMBUS SMBUS Slot 3 Slot 3 EP5xx...
  • Page 390 Cable Plan Data Cabling 10x2.5" PRAID EP4xx System Board System Board 10x2.5" HDD 10x2.5" HDD A3C40197295 A3C40197295 X40 - Power X40 - Power X42 - OOB X42 - OOB MLC2 MLC2 SAS Expander SAS Expander MLC1 MLC1 A3C40167225 A3C40167225 SATA ODD SATA ODD HDD LED HDD LED...
  • Page 391 Cable Plan Data Cabling 10x2.5" CP2100-8i System Board System Board 10x2.5" HDD 10x2.5" HDD A3C40197295 A3C40197295 X40 - Power X40 - Power X42 - OOB X42 - OOB MLC2 MLC2 SAS Expander SAS Expander MLC1 MLC1 A3C40167225 A3C40167225 SATA ODD SATA ODD HDD LED HDD LED...
  • Page 392 Cable Plan Data Cabling 10x2.5" PRAID EP5xx System Board System Board 10x2.5" HDD 10x2.5" HDD A3C40197295 A3C40197295 X40 - Power X40 - Power X42 - OOB X42 - OOB MLC2 MLC2 SAS Expander SAS Expander SATA ODD SATA ODD MLC1 MLC1 A3C40167225 A3C40167225...
  • Page 393 Cable Plan SERIAL ext. System Board System Board PWR MAIN PWR MAIN PWR 1 PWR 1 PC98 PC98 PWR 2 PWR 2 PWR 3 PWR 3 FRONTPANEL 1 FRONTPANEL 1 Front USB Front USB FRONTPANEL 2 FRONTPANEL 2 USB 1 USB 1 Front VGA Front VGA...
  • Page 394 Cable Plan Dual microSD 64GB Enterprise System Board CON1 USB 1 Dual microSD 64GB Enterprise RX1330 M4...
  • Page 395 System Status: Planned System Name: PRIMERGY RX1330 M4 CPU sockets: #PCIe Slots of system: Riser Option support: y/n Overview and properties of System PCI devices and slots List of Released Adapters incl. Installation sequence and priority System PCI Slot #...
  • Page 396 Adapter Installation Sequence Order within Adapter Adapter Class Category Adapter Product Name Max # Category (Cluster) Description (Softwarepool) Adapter 2 n/a if 3FH USB intern M.2 SSD1 M.2 SSD2 PRAID EP420i PRAID EP400i PRAID CP500i PRAID CP400i Controller Card - SAS int PSAS CP400i PSAS CP503i PSAS CP 2100-8i...
  • Page 397 Adapter Installation Sequence Order within Adapter Adapter Class Category Adapter Product Name Max # Category (Cluster) Description (Softwarepool) Adapter 2 n/a if 3FH USB intern M.2 SSD1 M.2 SSD2 PFC EP LPe 32000 1x32Gb PFC EP QLE 2740 1x32Gb PFC EP LPe31000 1x 16Gb Emulex PFC EP QLE2690 1x 16Gb Qlogic...
  • Page 398 List of all used screws for PRIMERGY Servers Assembled in Germany and Japan February 2019...
  • Page 399 / JIS 1012 type A3C40137316 / LSZ: L3-25419-01 hexagon head C26192-Y10-C151 M3 x 3.5 mm 5 mm / cross black 0.6 Nm S301 M3 x 5 mm F6-SW2N3-05121 with spring Phillips PH2 silver 0.6 Nm and washer Copyright 2019 FUJITSU LIMITED...
  • Page 400 M3 x 6 mm F6-SW2N3-06121 with spring Phillips PH2 silver 0.6 Nm and washer countersink C26192-Y10-C111 M3 x 6 mm silver 0.6 Nm Phillips PH2 S308 countersink F6-SSA3-06121 M3 x 6 mm silver 0.6 Nm Phillips PH2 Copyright 2019 FUJITSU LIMITED...
  • Page 401 0.6 Nm / JIS 1012 type CA32432-0170 6-32 x 4 mm Knurled screw S506 C26192-Y10-C211 Phillips PH1 black 0.2 Nm M3 x 4.5 mm Knurled screw S507 A3C40218449 Phillips PH1 silver 0.2 Nm M3 x 15 mm Copyright 2019 FUJITSU LIMITED...
  • Page 402 M2 x 3.5 mm silver 0.2 Nm PDUAL Phillips PH 0 AP200 kit) Denotation scheme S2xx : Screws M2x S3xx : Screws M3x S4xx : Screws M4x S5xx : Screws for special application S6xx : Bolts Copyright 2019 FUJITSU LIMITED...
  • Page 403 09. November 2018 Bolt and screw for M.2 on board Screw C26361-B443-C220 screw is part of PDUAL AP200 09. January 2019 C26361-Y10-C133 Flat head Kurled screw RAID controller 19. February 2019 : A3C40218449 and RX2530 M5 Copyright 2019 FUJITSU LIMITED...

Table of Contents