Quick Links
INSTALLATION AND MAINTENANCE INSTRUCTIONS
D355PL Duct Smoke Detector
SPECIfICATIONS
Operating Temperature:
–4° to 158°F (–20° to 70°C)
32° to 120°F (0° to 49°C) with module installed in the D355PL
Storage Temperature:
–22° to 158°F (–30° to 70°C)
Humidity:
0% to 93% Relative Humidity Non-condensing
Air Velocity:
100 to 4000 ft./min. (0.5 to 20.3 m/sec.)
Rectangular Footprint Dimensions:
14.38 in L×5 in W×2.5 in D (37 cm L×12.7 cm W×6.36 cm D)
Square Footprint Dimensions:
7.75 in L×9 in W×2.5 in D (19.7 cm L×22.9 cm W×6.35 cm D)
Weight:
1.8 pounds; 0.82 kg
Operating Voltage Range:
15 to 32 VDC
Standby Current:
300µA @ 24 VDC (one communication every 5 seconds with LED blink enabled)
Max. Alarm Current (LED on):
6.5 mA @ 24 VDC
NOTE: The D355PL come with the sensor head factory installed, part number SD355R.
Table of Contents
[1] Limitations of Duct Smoke Detectors . . . . . . . . . . . . . . . . . . . . . . . . .1
[2] General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[3] Contents of the Duct Smoke Detector Kit . . . . . . . . . . . . . . . . . . . . . .1
[4] Detector Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[5] Sampling Tube Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
[6] Measurement Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
[7] Field Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
[8] Verification of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
[9] Dectector Cleaning Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
[10] Sensor Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
[11] Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Warranty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
BEfORE INSTALLINg
Read the System Sensor Guide for Proper Use of Smoke Detectors in Duct Appli-
cations (A05-1004), which provides detailed information on detector spacing,
placement, zoning, wiring, and special applications. Copies of this manual
are available online at www.systemsensor.com. NFPA Standards 72 and 90A
should also be referenced for detailed information.
NOTICE: This manual shall be left with the owner/user of this equipment.
IMPORTANT: This detector must be tested and maintained regularly following
NFPA 72 requirements. The detector must be tested an maintained regularly
following NFPA 72 requirements. According to NFPA, the detector should be
visually inspected semiannually and functionally tested at least once a year.
This may need to be more frequent depending on the air quality of the duct
supply air.
[1]LIMITATIONS Of DUCT SMOkE DETECTORS
WARNING
The National Fire Protection Association has established that DUCT DETEC-
TORS MUST NOT BE USED AS A SUBSTITUTE FOR OPEN AREA DETECTOR
PROTECTION as a means of providing life safety. Nor are they a substitute for
early warning in a building's regular fire detection system.
System Sensor supports this position and strongly recommends that the user
read NFPA Standards 90A, 72, and 101. The D355PL Air Duct Smoke Detectors
are listed per UL 268A.
This device will not operate without electrical power. Fire situations may
cause an interruption of power. The system safeguards should be discussed
with your local fire protection specialist.
This device will not sense smoke unless the ventilation system is operating
and the cover is installed.
For this detector to function properly, it MUST be installed according to the in-
structions in this manual. Furthermore, the detector MUST be operated within
ALL electrical and environmental specifications listed in this manual and the
sensor head installation manual. Failure to comply with these requirements
may prevent the detector from activating when smoke is present in the air duct.
FL-300-000
Northford, CT 06472
ACCESSORY CURRENT LOADS AT 24 VDC
DEVICE
STANDBY
RA400Z/RA100Z
0mA
RTS451/RTS151
0mA
RTS451KEY/
12mA
RTS151KEY
[2]gENERAL DESCRIPTION
Page
Smoke introduced into this air duct system will be distributed throughout the
entire building. Smoke detectors designed for use in air duct systems are used
to sense the presence of smoke in the duct.
Model D355PL Air Duct Smoke Detector utilizes photoelectric technology for
the detection of smoke. This detection method, when combined with an ef-
ficient housing design, samples air passing through the duct and allows detec-
tion of a developing hazardous condition. When sufficient smoke is sensed,
an alarm signal is initiated at the fire control panel monitoring the detector,
and appropriate action can be taken to shut off fans, blowers, change over air
handling systems, etc. These actions can facilitate the management of toxic
smoke and fire gases throughout the areas served by the duct system.
The D355PL incorporates a sensor cover tamper feature that provides a trou-
ble signal at the panel immediately if the cover is removed or improperly in-
stalled. Proper installation of the sensor cover removes the trouble condition.
If programmed with the system control panel, two LEDs on each duct smoke
detector light to provide local visible indication.
The D355PL provides a remote alarm output for use with auxiliary devices,
such as the RA400Z/RA100Z remote LED annunciator, as well as remote test ca-
pability with the RTS451/151 or RTS451KEY/RTS151KEY Remote Test Stations.
[2.1] DETECTOR fEATURE SET
– Utilizes plug-in head, part number SD355R
– Sampling tubes install from front and rear
– Compatible with existing accessories
– Able to address detector per code switches on sensor head.
[3]CONTENTS Of ThE DUCT SMOkE DETECTOR kIT
1. Sensor/power board assembly and covers sensor head is factory installed
2. Three #10 sheet metal screws for mounting
3. Drilling template
4. One sampling tube end cap
5. One plastic exhaust tube
NOTE: A sampling tube must be ordered to complete the installation. It must
be the correct length for the width of the duct where it will be installed. See
Table 1 on page 3 to determine the inlet tube required for different duct widths.
[4]DETECTOR INSTALLATION
[4.1]VERIfy DUCT AIR fLOw DIRECTION AND VELOCITy
Model D355PL detectors are designed to be used in air handling systems hav-
ing air velocities of 100 to 4000 feet per minute. Duct widths from 6 inches to
12 feet can be accommodated. Be sure to check engineering specifications to
ensure that the air velocity in the duct falls within these parameters. If neces-
sary, use a velocity meter (anemometer) to check the air velocity in the duct.
[4.2]DETERMINE MOUNTINg LOCATION AND CONfIgURATION
On ducts wider than 18 inches it is recommended that the detector be
mounted downstream of a bend, obstruction in the duct, or the supply or
return air inlet.
Exception: Installation of duct detectors can be on or within a commercial
1
One FireLite Place
Phone: 203.484.7161
ALARM
12mA Max.
12mA Max.
12mA Max.
I56-3255-007R
Related Manuals for Honeywell Fire-Lite Alarms Innovair flex D365PL
Summary of Contents for Honeywell Fire-Lite Alarms Innovair flex D365PL
- Page 1 INSTALLATION AND MAINTENANCE INSTRUCTIONS One FireLite Place Northford, CT 06472 D355PL Duct Smoke Detector Phone: 203.484.7161 SPECIfICATIONS Operating Temperature: –4° to 158°F (–20° to 70°C) 32° to 120°F (0° to 49°C) with module installed in the D355PL ACCESSORY CURRENT LOADS AT 24 VDC Storage Temperature: –22°...
- Page 2 fIgURE 1. ExPLODED VIEw Of DUCT SMOkE DETECTOR COMPONENTS: EXHAUST TUBE WIRING COMPARTMENT WIRING COMPARTMENT COVER SAMPLING TUBE SOLD SEPERATELY SENSOR MODULE SENSOR HEAD NOTE: SENSOR HEAD IS ONLY H0569-06 INCLUDED ON SPECIFIED MODELS. SENSOR MODULE COVER packaged rooftop heating and air-conditioning system, fire/smoke dampers Use two (rectangular configuration) or three (square configuration) of the pro- and economizers.
- Page 3 CAUTION: The sampling tube end cap, included with the detector, is criti- [5.4]REMOTE SAMPLINg TUBE INSTALLATION cal to proper operation of the duct smoke detector. The end cap is needed to The detector arrangement can also incorporate the remote mounting of the create the proper air flow to the sensor of the duct smoke detector.
- Page 4 [7.1]wIRINg INSTRUCTIONS [8.4.1]TEST ThE UNIT [10]SENSOR REPLACEMENT [11.2] OPTION 2: REMOTE TEST USINg A TEST COIL: Disconnect power from the communication line before installing the D355PL 1. M02-04-00 Magnet Test (not included) This sensor can be functionally tested 1. Remove the sensor head by rotating counterclockwise. The use of a remote test station requires the installation of an accessory duct smoke detector.