Page 1
H8908A/B Humidistat; H8908C/D Dehumidistat INSTALLATION INSTRUCTIONS APPLICATION The H8908 family of low-voltage humidistats/ dehumidistats provide accurate control of whole house humidifiers, dehumidifiers, and ventilators. They have a snap-acting, dust-proof SPST switch and can be mounted to a duct or wall.
H8908A/B HUMIDISTAT; H8908C/D DEHUMIDISTAT DUCT INSTALLATION REMOTE MOUNT INSTALLATION 1. Choose a location on the duct. 1. Choose a location in the living area. ALTERNATE LOCATION NOTE: Select a location clear of drafts or excessive RETURN RETURN humidity. Avoid mounting near doors or win- dows, or in bathrooms or kitchens.
Page 3
H8908A/B HUMIDISTAT; H8908C/D DEHUMIDISTAT 4. Remove the base bracket from the humidistat. For 5. Secure the base bracket to the duct or remote loca- duct mount, slide the black gasket onto the base tion. Secure to the duct with four 1-in. (25 mm) bracket.
Page 4
H8908A/B HUMIDISTAT; H8908C/D DEHUMIDISTAT WIRING H8908 CAUTION Personal Injury Hazard. Can cause electrical shock and injury. (HOT) POWER Disconnect power before installation or servicing. FAN CONTROL SUPPLY All wiring must comply with applicable local codes, TRANSFORMER ordinances and regulations. Make wiring connections...
Page 5
H8908A/B HUMIDISTAT; H8908C/D DEHUMIDISTAT H8908 H8908 PRESSURE SWITCH/ FAN WIRING SAIL SWITCH TERMINALS SYSTEM HUMIDISTAT TRANSFORMER TERMINALS HUMIDIFIER 24V WIRING. NOTE: FOLLOW THE INSTALLATION INSTRUCTIONS (HOT) INCLUDED WITH THE STEAM HUMIDIFIER HUMIDIFIER TO WIRE THE SYSTEM FAN. POWER SUPPLY. PROVIDE DISCONNECT MEANS M24731 AND OVERLOAD PROTECTION AS REQUIRED.
H8908A/B HUMIDISTAT; H8908C/D DEHUMIDISTAT CHECKOUT OPERATION Turn the H8908 dial to “ON” to test proper installation. Humidity Control Adjustment See Fig. 20. To maintain optimal humidity levels without causing You will hear an audible click if installed correctly, and condensation on cold surfaces such as windows, the water will begin flowing to the humidifier.
Page 9
Humidistat H8908A/B Déshumidistat H8908C/D NOTICE D'INSTALLATION APPLICATION Les humidistats et les déshumidistats basse tension de la gamme H8908 assurent la régulation précise de l'humidification, la déshumidification et la ventilation dans toute la maison. Ils fonctionnent au moyen d'un interrupteur unipolaire unidirectionnel à rupture brusque, à...
Page 10
HUMIDISTAT H8908A/B DÉSHUMIDISTAT H8908C/D INSTALLATION SUR UNE GAINE MONTAGE À DISTANCE DANS UNE PIÈCE 1. Choisir l'emplacement sur la gaine. EMPLACEMENTS POSSIBLES 1. Choisir l'emplacement de montage dans la pièce. RETOUR RETOUR REMARQUE : Choisir un emplacement à l'abri des cou- D’AIR...
Page 11
HUMIDISTAT H8908A/B DÉSHUMIDISTAT H8908C/D 4. Retirer la plaque de montage de l'humidistat. Dans 5. Poser la plaque de montage sur la gaine ou à le cas d'une installation sur une gaine, insérer la l'emplacement choisi dans la pièce. Fixer à la gaine garniture d'étanchéité...
Page 12
HUMIDISTAT H8908A/B DÉSHUMIDISTAT H8908C/D RACCORDEMENT bas de l'humidistat pour enclencher la charnière du bas. Un clic se fait entendre lorsque l'humidistat est bien en place. MISE EN GARDE Risque de blessure Peut causer des chocs électriques et des blessures. Débrancher toute source d'alimentation avant d'installer ou de réparer.
Page 13
HUMIDISTAT H8908A/B DÉSHUMIDISTAT H8908C/D H8908 H8908 PRESSOSTAT D'AIR/ INTERRUPTEUR À AILETTE FILS DU SOLÉNOÏDE DE L’EAU TRANSFORMATEUR TRANSFORMATEUR L1 (SOUS L1 (SOUS TENSION) TENSION) HUMIDIFICATEUR ALIMENTATION. FOURNIR, AU BESOIN, UN DISPOSITIF DE COUPURE ET UNE PROTECTION CONTRE LES SURCHARGES. RELAIS À...
Page 14
HUMIDISTAT H8908A/B DÉSHUMIDISTAT H8908C/D THERMOSTAT VISIONPRO ® H8908D VENTILATEUR/DÉSHUMIDIFICATEUR BORNES H8908D Fresh Air Ventilation System Système de ventilation à air frais RELAIS DE CHAUFFAGE MF24732 OU BOBINE DE LA VANNE Fig. 19. Schéma de raccordement typique dans des applications de ventilation avec un HR150, HR200, ER150 et ER200 ou de déshumidification avec un...
HUMIDISTAT H8908A/B DÉSHUMIDISTAT H8908C/D VÉRIFICATION FONCTIONNEMENT Tourner le cadran du H8908 jusqu'à la position Réglage du régulateur d'humidité « marche » pour vérifier le fonctionnement de l'installation. Voir la Fig. 20. Pour obtenir un niveau d'humidité optimal sans condensation sur les surfaces froides comme les Si l'installation est bien effectuée, un clic se fait entendre...