HP T2 TOUCHPANEL CUSTOMER SUPPORT SERVICE MANUAL CONTENTS 1. OVERVIEW AND WORKING PRINCIPLE .....................4 1.2. Working Principle: ........................4 2. TECHNICAL SPECIFICATIONS ......................5 3. INSTALLATION ..........................5 3.1. Issues that should be informed to customer ................5 4. CONTROL PANEL AND PROGRAM SELECTION TABLE................6 4.1.
Page 3
HP T2 TOUCHPANEL CUSTOMER SUPPORT SERVICE MANUAL 6.20. Humidity Sensor ........................34 6.21. Door latch ..........................35 6.22. Plinth ........................... 36 6.23. Cooling Fan .......................... 37 6.24. Plinth Cover.......................... 38 6.25. Door ............................. 39 6.26. Drum Bearing Wheel ......................40 6.27.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 1. OVERVIEW AND WORKING PRINCIPLE 1. Top Plate 2. Control Panel 3. Loading Door 4. Plinth 5. Plinth opening slot 6. Ventilation grills 7. Adjustable feet 8. Plinth cover 9. Type plate 10. Lint filter 11.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 2. TECHNICAL SPECIFICATIONS Manufacturer Vestel White Goods Capacity (max) 7 kg 8 kg / 9kg Height Min: 845mm Max: 855 mm Min: 845mm Max: 855 mm Depth 563 mm 609 mm Width 596 mm...
HP T2touch PANEL CUSTOMER SERVICE MANUAL SUPPORT 4. CONTROL PANEL AND PROGRAM SELECTION TABLE 4.1. Control Panel Display Symbols 4.2.Program List KNOB POSITION PROGRAM Cotton Extra Dry Cotton Cupboard Dry Cotton Iron Dry Synthetics Cupboard Dry Synthetics Iron Dry Delicate...
HP T2touch PANEL CUSTOMER SERVICE MANUAL SUPPORT ***Time Drying Program: Humidity sensor is deactivated. The program ends when the time is up, without checking the humidity of the laundry. ***Express 34’/ Shirts 20 ‘: Humidity sensor is activated. The program time may extend, if the customer use different laundry according to the load in the program description.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 5.1. Failure Modes and Warning Leds T3 HEAT PUMP MODEL ERROR CODES ERROR CODE REASON T3 UI board doesn't receive communication from mainboard Aquaswitch connector is disconnected Compressor connector is disconnected Compressor NTC connector is disconnected...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 5.2. Service Autotest Steps Mini Step Error STEPS Control Led Indication Possible Errors code Dura tion* Set program knob at position 3. Push SW5 button. Keeping SW5 button pushed, turn program knob to position 1.
Page 10
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL Service must check Step 5 whether tumble is (Knob Motor CW (Tumble CCW) -Motor moving to CCW *If tumble is moving to Position stops CW again, then motor relay short circuit CCW Step 6...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6. DISASSEMBLY 6.1. Top Plate Remove two screws that fix the top plate at the back . Remove by pulling the top plate to yourself .
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.2. Control Panel Remove 2 screws from the top After the water tank removed, the plastic screw in the center of the control panel should be removed...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.3. Control Panel 1. After removing the screws on the control panel, the control panel is removed as shown in the photo from the upper support bracket. 2. The cables on the control panel are carefully removed from the cable paths.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.4. Electronic Card 1. To remove the electronic card box (PCB box) from the control panel, it is necessary to remove 6 tabs. As shown in the photo, you can take off the tabs with thin screwdriver.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.6. Side Panel Remove 10 screws on side panels...
Page 17
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.6. Side Panel 2. Remove 2 screws from front 3. It should not be forgotten to take bottom screw ( 2 screws) 4. Remove the side plate which is pulled out screws , by pushing up...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.7. Supply Cable 1. Remove the supply cable brown and blue cable socket. 2. Remove the terminals with tool as shown in the photo 3. Remove supply cord by pushing up...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.8. Emi Filter 1. Remove EMI filter sockets Remove the terminals with tool as shown in the photo 3. Remove the EMI filter which is fixed with 2 screws to the rear panel...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.10.Pump 1. Remove the screw on pump cover Remove 2 hoses that is connected with pum 2. After opening the pump holder plastic cover, 3. Remove aqua switch and pump socket. 4. Remove the pump holder plastic from basement plastic as shown in the photo...
Page 22
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.10.Pump 5. Push the pump from plastic. 6. There is a float in the pump housing as shown in the photo.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.11.Process Fan 1. Hold the fan as shown in the photo. 2. First remove washer and nut then remove the process fan.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.12. Rear Panel Remove segment on rear panel 2. Remove 8 screws from panel...
Page 25
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.12. Rear Panel 1. Remove hoses from rear panel 2. Remove the rear panel by pulling to yourself...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.13.Rear Isolation Group 1. For disassembling the rear Isolation group on rear panel, screws are shown in the photo should be removed.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.14. Rear Bearing Group 1. For disassembling the rear bearing group on rear panel, screws are shown in the photo should be removed.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.15.Water Tank Housing 1. Remove 2 hoses from water tank housing. 2. Remove the water tank housing clips . 3. The water tank housing is removed as in the photo.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.16. Drum 1. Motor should be moved up to prevent to press spring. So, belt will be released as shown in the photo. 2. Remove the belt on the drum 3. Pull up the drum to separate with basement plastic. Then, pull back to remove.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.17. Motor 1. Remove capacitor sockets and other sockets from motor. PS: before removing the motor, process fan should be removed. You can apply the same instruction to change the belt...
Page 31
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.17.Motor 2. Remove 4 screws from motor fixing plastic 3. Take the motor from basement plastic as shown in the photo.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.18.Capacitors 1. Remove all sockets from motor. 2. Remove the screw on bottom of capacitor then disassemble the capacitor 3. The capacitor is removed by turning.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.20. Humidity Sensor 1. Remove 5 screws from humidity sensor plastic. 2. Remove the humidity sensor cable as shown in photo.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.21. Door latch 1. Remove door latch screw from front panel. 2. Separate the door latch socket from door latch as shown in the photo.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.23. Cooling Fan 1. Remove screws on cooling fan fixing plastic 2. Remove the cooling fan fixing plastic as shown in the photo. 3. Disassemble the cooling fan by removing the fan screws and fan ground wire.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.27. Drumlight 1. Remove Drumlight group from Front Shield 2. Remove the drum light socket. 3. Remove the drum light card.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.28. Front Panel Remove 16 screws on the front panel While removing the front panel, the cable of the door latch must also be removed.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.29. Door NTC 1. Remove the socket from NTC sensor on the basement plastic. 2. Remove the NTC from basement plastic by hand or tool...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.30. Side Bracket 1. Remove cable holder plastic clips shown in the photo. (For right side bracket) Remove screw from bracket which is fixing side bracket and top bracket . (Rear panel was...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.31. Front Shield 1. Remove 2 screws in the bottom. 2. Open clips on the left side. 3. The front shield should be lifted as shown in the photo.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.32.Front Isolation Foam Sticky paper Front Isolation mark Force direction 1. It is important to install the new felt correctly after it has been removed from the slot at the front shield. 2. Before Sticky paper is opened, front isolation foam should be placed to slot on front shield.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.33. Cable Group 1. Open the cable holder plastic clips on side bracket. 2. Remove cable holder plastic fixing clips as shown in the photo.
Page 48
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 6.34. Cable Group 1. Humidity Sensor Cable 4. Compressor NTS Socket 2. Door Latch Socket Cable 5. Compressor Ground Cable 3. Cable Group of Front Shield 6. Compressor Socket...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 7. 7. COMPONENT SPECIFICATIONS AND MEASUREMENTS 7.1. Motor The dryer has an asynchronous motor. In the photo on the right, the socket on the motor are shown to be measured by multiple counters. It is driven with triac via the electronic card (to give energy) and relay (for direction control).
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 7.2. Pump In Tumble Dryer models, the pump is used to transport the water that accumulates in the condensation chamber to tank in the drawer area. One triac is measured on the electronic card.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 7.3. Electronic Card Technical Features Electronic card is single sided printed circuit board and CEM-1 material 7.4. Door/Compressor NTC Sensor Two NTC sensors are used. The NTC resistance decreases when the temperature rises.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 7.4.1. Door NTC Sensor Measurements 7.5. Compressor The dryer has an compressor with an asynchronous motor. In the photo on the right, the terminal on the compressor are shown to be measured by multiple counters. It is...
Page 55
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL Aux windings: 8.75±7% (25 °C temp.) Motor speed : 2928 rpm (Unloaded) Gas Type: R290 Capacitor value : 20 µF ± %5 Compressor Capacity: 7.8 cm³/rev Component Test Check whether the compressor cable is connected to the compressor terminal.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 7.6. Door Latch Door latch locks when the door is closed. It’s designed to be opened from inside, in case of children are in the drum Component Test When the door is closed, check whether there is electrical transmission from IDC connected to electronic card ...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 7.7. Humidity Sensor The Humidity Sensor measures the amount of dryness of the laundry in the drum. Component Test Each humidity sensor plate is checked whether there is electrical transmission from IDC connected to electronic card.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 7.8. Cooling Fan The dryer has an cooling fan with an asynchronous motor. In the photo on the right, the terminal on the compressor are shown to be measured by multiple counters. It is driven with triac via the...
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 7.8.1. Cooling Fan Measurements 7.9. Drumlight Drumlight lights inside of the drum Component Test Check whether there is electrical transmission from IDC connected to electronic card.
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL 8. TROUBLESHOOTING MACHINE IS NOT WORKING If Machine has no power Is there power Machine has not a failure on power sockets(outlet) ? (220V-50 Hz) Is The Supply Make Electrical Connection Cord Plugged...
Page 62
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL MACHINE IS NOT WORKING If machine has power Is the door Close / Repair the door closed? Is the door latch socket connection Make Electrical Connection correct ? Check the door latch with...
Page 63
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL MACHINE IS NOT DRYING Is the Filter and Clean Filter and / or Condenser Condenser Clean? Is compressor Wait temperature of the compressor surface overload decrease room temperature and check again. protector open...
Page 64
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL DRUM IS NOT ROTATING Is Right and Wheels may be stuck or Is Drum Rotating Left Wheel damaged. Replace the With Hand? Rotating wheels. Is belt position Fix The Position of Is Drum as It...
Page 65
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL E04 ERROR Is connection of compressor Fix Compressor Connections connector correct? Are the measured resistance values Change The Compressor t hrough the compressor connector correct? Is There a Disconnection Between Is machine...
Page 66
HP T2touch PANEL CUSTOMER SUPPORT SERVICE MANUAL E07 ERROR Is Right and Wheels may be stuck or Is Drum Rotating Left Wheel damaged. Replace the With Hand? Rotating wheels. Are all connections btw Fix the connections motor and main board Is there any and try again.