Related Manuals for Dell OptiPlex 3000 Tower
Summary of Contents for Dell OptiPlex 3000 Tower
- Page 1 OptiPlex 3000 Tower Service Manual Regulatory Model: D32M Regulatory Type: D32M002 March 2022 Rev. A00...
- Page 2 A WARNING indicates a potential for property damage, personal injury, or death. © 2022 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.
-
Page 3: Table Of Contents
After working inside your computer..........................9 BitLocker..................................9 Chapter 2: Removing and installing components................10 Recommended tools................................10 Screw list..................................... 10 Major components of OptiPlex 3000 Tower........................11 Side cover.................................... 13 Removing the side cover............................13 Installing the side cover.............................. 15 Front bezel ..................................17 Removing the front bezel............................17... - Page 4 Removing the graphics card............................. 40 Installing the graphics card............................42 Removing optional SMA module..........................43 Installing optional SMA module..........................44 Removing the Dell Ultra Speed Drive Gen4 card....................45 Installing the Dell Ultra Speed Drive Gen4 card....................45 Slim optical-drive................................46 Removing the Slim optical drive..........................46 Installing the Slim optical drive..........................47...
- Page 5 Deleting or changing an existing system setup password................104 Clearing CMOS settings..............................105 Clearing BIOS (System Setup) and System passwords..................105 Chapter 5: Troubleshooting....................... 106 Dell SupportAssist Pre-boot System Performance Check diagnostics.............. 106 Running the SupportAssist Pre-Boot System Performance Check.............. 106 Power-Supply Unit Built-in Self-Test ........................106 System-diagnostic lights..............................107 Recovering the operating system..........................108...
-
Page 6: Chapter 1: Working Inside Your Computer
You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance. -
Page 7: Safety Precautions
ESD protection is an increasing concern. Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable. -
Page 8: Esd Field Service Kit
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while performing service and that they use anti-static bags for transporting sensitive components. -
Page 9: Transporting Sensitive Components
Transporting sensitive components When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport. Lifting equipment Adhere to the following guidelines when lifting heavy weight equipment: CAUTION: Do not lift greater than 50 pounds. -
Page 10: Chapter 2: Removing And Installing Components
Removing and installing components NOTE: The images in this document may differ from your computer depending on the configuration you ordered. Recommended tools The procedures in this document may require the following tools: ● Phillips screwdriver #0 ● Phillips screwdriver #1 ●... -
Page 11: Major Components Of Optiplex 3000 Tower
Table 1. Screw list (continued) Component Screw type Quantity Screw image System board #6-32 M2x4 6-32 Major components of OptiPlex 3000 Tower The following image shows the major components of OptiPlex 3000 Tower. Removing and installing components... - Page 12 1. Side cover 2. 3.5-inch hard-disk drive 3. Slim ODD 4. Heat sink 5. WLAN card 6. Memory module 7. M.2 2280 solid-state drive 8. Power button Removing and installing components...
-
Page 13: Side Cover
17. 2.5-inch hard-disk drive NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for purchase options. - Page 14 Removing and installing components...
-
Page 15: Installing The Side Cover
Steps 1. Loosen the two thumbscrews that secure the side cover to the computer. 2. Slide the side cover towards the rear of the computer and lift the side cover away from the chassis. Installing the side cover Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the side cover and provides a visual representation of the installation procedure. - Page 16 Removing and installing components...
-
Page 17: Front Bezel
Steps 1. Align the tabs on the side cover with the slots on the chassis. 2. Slide the side cover towards the front of the computer to install it. 3. Tighten the two thumbscrews to secure the side cover to the chassis. Next steps 1. -
Page 18: Installing The Front Bezel
Steps 1. Pry the retention tabs to release the front bezel from the computer. 2. Slightly pull the front bezel and gently rotate to release the other tabs on the bezel from the slots in the computer chassis. 3. Remove the front bezel from the computer. Installing the front bezel Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. - Page 19 Steps 1. Position the front bezel to align the tabs on the bezel with the slots on the chassis. 2. Press the bezel until the tabs clicks into place. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer.
-
Page 20: Hard-Drive Assembly
Hard-drive assembly Removing the 2.5-inch hard drive assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the duct. About this task The following images indicate the location of the 2.5-inch hard drive assembly and provide a visual representation of the removal procedure. - Page 21 Steps 1. Disconnect the hard drive data and power cables from the connectors on the 2.5-inch hard drive modules. 2. Press the release tabs on both the sides of the hard drive bracket to release it from the slots on the computer chassis. 3.
-
Page 22: Removing The Secondary 2.5-Inch Hard Drive Assembly
Removing the secondary 2.5-inch hard drive assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. About this task The following images indicate the location of the 2.5-inch hard drive and provide a visual representation of the removal procedure. - Page 23 Steps 1. Remove the two (M3x3.5) screws that secure the primary 2.5-inch hard drive to the hard drive bracket. 2. Lift to remove the primary 2.5-inch hard drive from the hard drive bracket. 3. Remove the two (M3x3.5) screws that secure the secondary 2.5-inch hard drive to the hard drive bracket. 4.
-
Page 24: Installing The 2.5-Inch Hard Drive Bracket
NOTE: The orientation or the SATA connector marking on the hard drive so that you can replace it correctly. Installing the 2.5-inch hard drive bracket Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the 2.5-inch hard drive bracket and provides a visual representation of the installation procedure. - Page 25 Steps 1. Align the screw holes and place the secondary 2.5-inch hard drive into the hard-drive bracket. 2. Replace the two (M3x3.5) screws that secure the secondary 2.5-inch hard drive to the hard-drive bracket. 3. Align the screw holes and place the primary 2.5-inch hard drive into the hard drive bracket. 4.
-
Page 26: Installing The Secondary 2.5-Inch Hard Drive Assembly
Next steps 1. Install the 2.5-inch primary hard drive. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. Installing the secondary 2.5-inch hard drive assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the 2.5-inch hard drive assembly and provides a visual representation of the installation procedure. - Page 27 Steps 1. Align the hard drive assembly at an angle to the slot on the computer. 2. Press the release tabs on the hard drive bracket and slightly align back to insert the hard drive assembly to the slot on the computer chassis.
-
Page 28: 3.5 In. Hard-Drive Assembly
2. Install the side cover. 3. Follow the procedure in after working inside your computer. 3.5 in. hard-drive assembly Removing the 3.5-inch hard drive assembly Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. -
Page 29: Installing The 3.5-Inch Hard Drive Assembly
Installing the 3.5-inch hard drive assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the 3.5-inch hard drive assembly and provides a visual representation of the installation procedure. -
Page 30: Solid-State Drive
Solid-state drive Removing the M.2 2230 PCIe solid-state drive Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. About this task The following images indicate the location of the solid-state drive and provide a visual representation of the removal procedure. Steps 1. -
Page 31: Removing The M.2 2280 Pcie Solid-State Drive
About this task The following image indicates the location of the solid-state drive and provides a visual representation of the installation procedure. Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive connector. 2. Insert the solid-state drive at a 45-degree angle into the connector on the system board. 3. -
Page 32: Installing The M.2 2280 Pcie Solid-State Drive
Steps 1. Remove the screw (M2x3.5) that secures the solid-state drive to the system board. 2. Slide at an angle to lift and remove the solid-state drive from its connector on the system board. Installing the M.2 2280 PCIe solid-state drive Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 33: Wlan Card
Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive connector. 2. Insert the solid-state drive at a 45-degree angle into the connector on the system board. 3. Replace the screw (M2x3.5) to secure the M.2 2280 solid-state drive to the connector on the system board. Next steps 1. - Page 34 Steps 1. Remove the (M2x3.5) screw that secures the WLAN card to the system board. 2. Lift the WLAN card bracket away from the WLAN card. 3. Disconnect the antenna cables from the WLAN card. 4. Slide and remove the WLAN card from the connector on the system board. Removing and installing components...
-
Page 35: Installing The Wlan Card
Installing the WLAN card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the wireless card and provides a visual representation of the installation procedure. Removing and installing components... -
Page 36: Coin-Cell Battery
Steps 1. Connect the antenna cables to the WLAN card. The following table provides the antenna-cable color scheme for the WLAN card of your computer. Table 2. Antenna-cable color scheme Connectors on the wireless card Antenna-cable color Main (white triangle) White Auxiliary (black triangle) Black... -
Page 37: Installing The Coin-Cell Battery
Steps 1. Using a plastic scribe, gently pry the coin-cell battery out of the slot on the system board. 2. Remove the coin-cell battery away from the computer. Installing the coin-cell battery Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the coin-cell battery and provides a visual representation of the installation procedure. -
Page 38: Memory Module
Steps 1. Insert the coin-cell battery with the "+" sign facing up and slide it under the securing tabs at the positive side of the connector. 2. Press the battery into the connector until it locks into place. Next steps 1. -
Page 39: Installing The Memory Module
Steps 1. Pull the securing clips from both side of the memory module until the memory module pops up. 2. Slide and remove the memory module from the memory-module slot. Installing the memory module Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the memory module and provides a visual representation of the installation procedure. -
Page 40: Expansion Card
Steps 1. Align the notch on the memory module with the tab on the memory-module slot. 2. Slide the memory module firmly into the slot and press the memory module down until it clicks into place. NOTE: If you do not hear the click, remove the memory module and reinstall it. Next steps 1. - Page 41 About this task The following images indicate the location of the graphics card and provide a visual representation of the removal procedure. Steps 1. Lift the pull tab to open the PCIe door. 2. Push and hold the securing tab on the graphics-card slot and lift the graphics card from the graphics-card slot. Removing and installing components...
-
Page 42: Installing The Graphics Card
Installing the graphics card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the graphics card and provide a visual representation of the installation procedure. Removing and installing components... -
Page 43: Removing Optional Sma Module
Steps 1. Align the graphics card with the PCI-Express card connector on the system board. 2. Using the alignment post, connect the graphics card in the connector and press down firmly. Ensure that the card is firmly seated. 3. Lift the pull tab to close the PCIe door. Next steps 1. -
Page 44: Installing Optional Sma Module
Installing optional SMA module Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the optional SMA module and provide a visual representation of the installation procedure. -
Page 45: Removing The Dell Ultra Speed Drive Gen4 Card
2. Remove the side cover. About this task The following images indicate the location of the Dell Ultra Speed Drive Gen4 card and provide a visual representation of the removal procedure. Steps 1. Using the tab, lift and open the PCIe door. -
Page 46: Slim Optical-Drive
About this task The following image indicates the location of the Dell Ultra Speed Drive Gen4 card and provides a visual representation of the installation procedure. Steps NOTE: The Dell Ultra Speed Drive Gen4 card must be installed in the PCIe x4 slot. -
Page 47: Installing The Slim Optical Drive
Steps 1. Disconnect the data and power cables from the slim ODD. 2. Pull the securing tab to release the slim ODD from the chassis. 3. Slide and remove the slim ODD from the ODD slot. Installing the Slim optical drive Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 48: Slim Optical-Drive Bracket
Steps 1. Insert the slim ODD assembly into the ODD slot. 2. Slide the slim ODD assembly until it snaps into place. 3. Route the power cable and data cable through the routing guides and connect the cables to the slim ODD. Next steps 1. -
Page 49: Installing The Slim-Odd Bracket
About this task The following images indicate the location of the slim-ODD bracket and provide a visual representation of the removal procedure. Steps 1. Pry the slim-ODD bracket to release it from the slot on the ODD. 2. Remove the slim-ODD bracket off the ODD. Installing the slim-ODD bracket Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 50: Speaker
Steps 1. Align and place the slim-ODD bracket on the ODD slots. 2. Snap the slim-ODD bracket into the slim ODD. Next steps 1. Install the slim Optical Disk Drive. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. -
Page 51: Installing The Speaker
Steps 1. Disconnect the speaker cable from the connector on the system board. 2. Unroute the speaker cable from the routing guides on the chassis. 3. Press the tab and slide the speaker along with the cable from the slot on the chassis. Installing the speaker Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 52: Fan Shroud
Steps 1. Press and slide the speaker in the slot on the chassis until it snaps into place. 2. Route the speaker cable through the routing guide on the chassis. 3. Connect the speaker cable to the connector on the system board. Next steps 1. -
Page 53: Installing The Fan Duct
Steps 1. Press the retention tabs on both sides of the fan duct to release it. 2. Pull and remove the fan duct from the computer. Installing the fan duct Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the fan duct and provides a visual representation of the installation procedure. - Page 54 Steps 1. Position the fan duct to align it with the slots on the computer chassis. 2. Press the fan duct until it clicks into place. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer.
-
Page 55: Power-Supply Unit
Power-supply unit Removing the power-supply unit Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the duct. NOTE: Note the routing of all cables as you remove them so that you can route them correctly while you are replacing the power-supply unit. - Page 56 Steps 1. Lay the computer on the right side. 2. Disconnect the power cables from the system board and unroute them from the routing guides on the chassis. 3. Remove the three (#6-32) screws that secure the power-supply unit to the chassis. 4.
-
Page 57: Installing The Power-Supply Unit
Installing the power-supply unit Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. WARNING: The cables and ports on the back of the power-supply unit are color-coded to indicate the different power wattage. Ensure that you plug in the cable to the correct port. Failure to do so may result in damaging the power-supply unit and/or system components. - Page 58 Steps 1. Slide the power-supply unit into the chassis until the securing tab snaps into position. 2. Replace the three (#6-32) screws to secure the power-supply unit to the chassis. 3. Route the power cable through the routing guides on the chassis and connect the power cables to their respective connectors on the system board.
-
Page 59: Processor Fan And Heat-Sink Assembly
Next steps 1. Install the duct. 2. Install the side cover. 3. Follow the procedure in after working inside your computer. Processor fan and heat-sink assembly Removing the processor fan and heat-sink assembly Prerequisites 1. Follow the procedure in before working inside your computer. -
Page 60: Installing The Processor Fan And Heat-Sink Assembly
Steps 1. Disconnect the processor fan cable from the connector on the system board. 2. Loosen the four captive screws that secure the processor fan and heat-sink assembly to the system board. 3. Lift the processor fan and heat-sink assembly off the system board. Installing the processor fan and heat-sink assembly Prerequisites NOTE:... -
Page 61: Processor
Steps 1. Align the screw holes on the processor fan and heat-sink assembly with the screw holes on the system board. 2. Tighten the four captive screws that secure the processor fan and heat-sink assembly to the system board. 3. Connect the processor-fan cable to the connector on the system board. Next steps 1. -
Page 62: Installing The Processor
NOTE: The processor might still be hot after the computer is shut down. Allow the processor to cool down before removing About this task The following images indicate the location of the processor and provide a visual representation of the removal procedure. Steps 1. -
Page 63: Communication Card
Steps 1. Ensure that the release lever on the processor socket is fully extended in the open position. 2. Align the notches on the processor with the tabs on the processor socket and place the processor in the processor socket. NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor socket. - Page 64 Steps 1. Lift the pull tab to open the PCIe door. 2. Disconnect the communication card cable from its connector on the system board. 3. Unroute the communication card cable from the routing guides. 4. Lift and remove the communication card from the system board. 5.
-
Page 65: Installing The Communication Card
Installing the communication card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following image indicates the location of the communication card and provides a visual representation of the installation procedure. -
Page 66: Power Button
Steps 1. Lift the pull tab to open the PCIe door. 2. Place the communication card on the open PCIe door. 3. Route the communication card cable using the routing guides. 4. Connect the communication card cable to its connector on the system board. 5. -
Page 67: Installing The Power Button
Steps 1. Disconnect the power-button cable from the connector on the system board. 2. Press the release tabs on the power-button head and slide the power-button cable out from the front-side chassis of the computer. 3. Pull the power-button cable out from the computer. Installing the power button Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 68: Intrusion Switch
Steps 1. Insert the power-button cable into the slot from the front-side of the computer, and press the power-button head until it clicks into the place in the chassis. 2. Align and connect the power-button cable to the connector on the system board. Next steps 1. -
Page 69: Installing The Intrusion Switch
About this task The following image indicates the location of the intrusion switch and provides a visual representation of the removal procedure. Steps 1. Disconnect the intruder cable from the connector on the system board. 2. Slide and remove the intrusion switch from the chassis. Installing the intrusion switch Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. -
Page 70: Optional Modules
Steps 1. Insert the intrusion switch into its slot and slide the switch to secure it into the slot. 2. Connect the intruder cable to the connector on the system board. Next steps 1. Install the side cover. 2. Follow the procedure in after working inside your computer. -
Page 71: Installing Optional Displayport Module
About this task The following images indicate the location of the optional DisplayPort module and provide a visual representation of the removal procedure. Steps 1. Remove the two (M3X3) screws that secure the optional DisplayPort module to the computer chassis. 2. - Page 72 Steps 1. To remove the dummy metal bracket, insert a flat-head screwdriver in the hole of the bracket, push the bracket to release the bracket, and then lift the bracket out from the system. 2. Insert the optional DisplayPort module into its slot from the inside of your computer. 3.
-
Page 73: Removing Optional Vga Module
Removing optional VGA module Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel. About this task The following images indicate the location of the optional VGA module and provide a visual representation of the removal procedure. - Page 74 Steps 1. To remove the dummy metal bracket, insert a flat-head screwdriver in the hole of the bracket, push the bracket to release the bracket, and then lift the bracket out from the system. 2. Insert the optional VGA module into its slot from the inside of your computer. 3.
-
Page 75: Removing Optional Hdmi Module
Removing optional HDMI module Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel. About this task The following images indicate the location of the optional HDMI module and provide a visual representation of the removal procedure. - Page 76 Steps 1. To remove the dummy metal bracket, insert a flat-head screwdriver in the hole of the bracket, push the bracket to release the bracket, and then lift the bracket out from the system. 2. Insert the optional HDMI module into its slot from the inside of your computer. 3.
-
Page 77: Removing Optional Serial Module
Removing optional Serial module Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. 3. Remove the front bezel. About this task The following images indicate the location of the optional Serial module and provide a visual representation of the removal procedure. - Page 78 Steps 1. To remove the dummy metal bracket, insert a flat-head screwdriver in the hole of the bracket, push the bracket to release the bracket, and then lift the bracket out from the system. 2. Insert the optional Serial module into its slot from the inside of your computer. 3.
-
Page 79: Removing Internal Antenna
Removing internal antenna Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the side cover. About this task The following images indicate the location of the internal antenna and provide a visual representation of the removal procedure. Steps 1. -
Page 80: System Board
Steps 1. Insert the main-antenna into the ANT-W slot and auxiliary-antenna into the ANT-B slot. 2. Route the antennas using the routing guides and insert the antenna cables through the hole that is provided in the system chassis. 3. Replace the two screws to secure the main and auxiliary antennas to the system chassis. 4. - Page 81 NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can reconnect the cables correctly after you replace the system board. 2. Remove the side cover. 3. Remove the front bezel. 4. Remove the duct.
- Page 82 2. ATX CPU power connector 3. Memory module connectors 4. Power switch connector 5. Coin-cell battery 6. System power connector 7. SATA connector (white) 8. SATA power cable connector 9. SATA1 connector 10. M.2 WLAN connector 11. SATA0 connector (blue) 12.
- Page 83 Removing and installing components...
- Page 84 Removing and installing components...
-
Page 85: Installing The System Board
Steps 1. Remove the (#6-32) screw that secures the front I/O-bracket to the chassis. 2. Slide and remove the front I/O-bracket from the chassis. 3. Disconnect the power and HDD cables that are connected to the system board and unroute them from the routing guides on the chassis. - Page 86 1. Intrusion switch connector 2. ATX CPU power connector 3. Memory module connectors 4. Power switch connector 5. Coin-cell battery 6. System power connector 7. SATA connector (white) 8. SATA power cable connector 9. SATA1 connector 10. M.2 WLAN connector 11.
- Page 87 Removing and installing components...
- Page 88 Removing and installing components...
- Page 89 Removing and installing components...
- Page 90 Steps 1. Slide the front I/O-ports on the system board into the front I/O-slots on the chassis and align the screw holes on the system board with the screw holes on the chassis. 2. Replace the (M2x4) screw screw to secure the system board to the chassis. 3.
-
Page 91: Chapter 3: Drivers And Downloads
Drivers and downloads When troubleshooting, downloading or installing drivers it is recommended that you read the Dell Knowledge Based article, Drivers and Downloads FAQ 000123347. Drivers and downloads... -
Page 92: Chapter 4: Bios Setup
BIOS setup CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program. Certain changes can make your computer work incorrectly. NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed. NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen information for future reference. -
Page 93: System Setup Options
Depending on your computer and its installed devices, the items that are listed in this section may or may not appear. Table 5. System setup options—System information menu Overview OptiPlex 3000 Tower BIOS Version Displays the BIOS version number. Service Tag Displays the Service Tag of the computer. - Page 94 Table 5. System setup options—System information menu (continued) Overview DIMM 1 Size Displays the DIMM 1 memory size. DIMM 2 Size Displays the DIMM 2 memory size. DIMM 3 Size Displays the DIMM 3 memory size. DIMM 4 Size Displays the DIMM 4 memory size. Devices Information Video Controller Displays the video controller type of the computer.
- Page 95 Table 7. System setup options—Integrated Devices menu (continued) Integrated Devices Audio Enable Audio Enable or disable the integrated audio controller. By default, all the options are enabled. Serial Port Serial Port Configuration Enable or disable the serial port address. By default, the COM1: Port is configured at 3F8h with IRQ4 option is enabled.
- Page 96 Table 8. System setup options—Storage menu (continued) Storage Type Displays the SATA HDD type information of the computer. Device Displays the SATA HDD device information of the computer. M.2 PCIe SSD-0 Type Displays the M.2 PCIe SSD-0 type information of the computer. Device Displays the M.2 PCIe SSD-0 device information of the computer.
- Page 97 Table 10. System setup options—Connection menu (continued) Connection HTTPs Boot Mode With Auto Mode, the HTTPs Boot extracts Boot URL from the DHCP. With Manual Mode, the HTTPs Boot reads Boot URL from the user-provided data. By default, the Auto Mode option is enabled. Table 11.
- Page 98 Table 12. System setup options—Security menu (continued) Security By default, the SHA-256 option is enabled. Clear Enables to clear the TPM owner information and returns the TPM to the default state. By default, the Clear option is disabled. PPI ByPass for Clear Commands Controls the TPM Physical Presence Interface (PPI).
- Page 99 Allow Non-Admin PSID Revert Enable Allow Non-Admin PSID Revert Controls access to the Physical Security ID (PSID) revert of NVMe hard-drives from the Dell Security Manager prompt. By default, the option is disabled. Table 14. System setup options—Update, Recovery menu...
- Page 100 By default, the option is disabled. SERR Messages Enable or disable SERR messages. By default, the option is enabled. Dell Development Configuration Enable Flash Updated Signature Override Enable or disable certain features to control BIOS By default, the option is disabled.
- Page 101 Table 17. System setup options—Pre-boot Behavior menu (continued) Pre-boot Behavior Extend BIOS POST Time Set the BIOS POST time. By default, the 0 seconds option is enabled. Table 18. System setup options—Virtualization menu Virtualization Intel Virtualization Technology Enable Intel Virtualization Technology Specify whether a Virtual Machine Monitor (VMM) can utilize the additional (VT) hardware capabilities that are provided by Intel Virtualization Technology.
-
Page 102: Updating The Bios
Updating the BIOS in Windows to download the latest BIOS setup program file. 2. Create a bootable USB drive. For more information, search in the Knowledge Base Resource at www.dell.com/support. 3. Copy the BIOS setup program file to the bootable USB drive. -
Page 103: Updating The Bios From The F12 One-Time Boot Menu
One-Time boot menu on the computer. Most of the Dell computers built after 2012 have this capability, and you can confirm by booting your computer to the F12 One-Time Boot Menu to see if BIOS FLASH UPDATE is listed as a boot option for your computer. If the option is listed, then the BIOS supports this BIOS update option. -
Page 104: System And Setup Password
System and setup password Table 21. System and setup password Password type Description System password Password that you must enter to log in to your system. Setup password Password that you must enter to access and make changes to the BIOS settings of your computer. You can create a system password and a setup password to secure your computer. -
Page 105: Clearing Cmos Settings
Clearing BIOS (System Setup) and System passwords About this task To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell. NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying Windows or your application. -
Page 106: Chapter 5: Troubleshooting
Check diagnostics About this task SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The Dell SupportAssist Pre-boot System Performance Check diagnostics is embedded with the BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device groups allowing you to: ●... -
Page 107: System-Diagnostic Lights
Blinking pattern Amber White Problem description Suggested resolution Unrecoverable SPI Flash Failure CPU failure ● Run the Dell Support Assist/Dell Diagnostics tool. ● If problem persists, replace the system board. System board failure (included ● Flash latest BIOS version BIOS corruption or ROM ●... -
Page 108: Recovering The Operating System
It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its factory state. You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their primary operating system due to software or hardware failures. -
Page 109: Backup Media And Recovery Options
Backup media and recovery options It is recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes multiple options for recovering Windows operating system on your Dell PC. For more information. see... -
Page 110: Chapter 6: Getting Help And Contacting Dell
Getting help and contacting Dell Self-help resources You can get information and help on Dell products and services using these self-help resources: Table 23. Self-help resources Self-help resources Resource location Information about Dell products and services www.dell.com My Dell app...