GE JSS28BKBB Installation Instructions Manual
30” electric slide-in range
Hide thumbs
Also See for JSS28BKBB:
- Dimensions and installation information (2 pages) ,
- Owner's manual (25 pages)
Table of Contents
Quick Links
See also:
Owner's Manual
Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
•
instructions for local inspector's use.
IMPORTANT
•
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires basic mechanical skills.
• Completion time – 1 to 3 hours
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation
is not covered under the Warranty.
WARNING
be properly grounded.
FOR YOUR SAFETY:
CAUTION:
remove house fuse or open circuit breaker
before beginning installation. Failure to do so
could result in serious injury or even death.
TOOLS YOU WILL NEED
"
Drill with 1/8
Bit
Straight Edge
Hand or Saber Saw
31-10596-2
1-07 JR
— Save these
— Observe all
— This appliance must
— For Personal Safety
Safety Glasses
Tape Measure
Pencil
30" Electric
Slide-In Range
JSS28, JSP39
ANTI-TIP DEVICE
WARNING
of tipping, the appliance must be secured by
properly installed Anti-Tip bracket packed
with this appliance.
If the Anti-Tip device supplied with the range
does not fit this application, use the universal
Anti-Tip device WB2X7909.
If you pull the range out and away from the
wall for any reason, make sure the Anti-Tip
bracket is engaged when the range is pushed
back against the wall.
FOR YOUR SAFETY:
All rough-in and spacing dimensions must be
met for safe use of your range. Electricity to
the range can be disconnected at the outlet
without moving the range if the outlet is in
the preferred location (remove lower drawer).
To reduce the risk of burns or fire when
reaching over hot surface elements, cabinet
storage space above the cooktop should be
avoided. If cabinet storage space is to be
provided above the cooktop, the risk can
be reduced by installing a range hood that
sticks out at least 5" beyond the front of the
cabinets. Cabinets installed above a cooktop
must be no deeper than 13".
Be sure your appliance is properly installed
and grounded by a qualified technician.
1
— To reduce the risk
WARNING
• All ranges can tip
• Injury to persons could result
• Install Anti-Tip bracket packed
with range
• See Installation Instructions
—
Table of Contents
Related Manuals for GE JSS28BKBB
Summary of Contents for GE JSS28BKBB
-
Page 1: Installation Instructions
Installation Instructions Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT • — Save these instructions for local inspector’s use. IMPORTANT • — Observe all governing codes and ordinances. -
Page 2: Prepare To Install The Range
PREPARE TO INSTALL THE RANGE • Move range indoors in front of cabinet opening. • Protect the kitchen floor! Flatten and place a piece of the shipping carton in front of the installation location to protect the flooring. • Remove packing materials. Remove labels on door, plastic on trim and panel, and all tape around the range. -
Page 3: Minimum Clearances
• All rough-in and spacing dimensions must be met for safe use of your range. The location of the electrical outlet may be changed as needed, but electricity to the range can be... -
Page 4: Removing Packaging Material
4″ Backguard, Model #JXS32XX or a Main Top Rear Filler Kit, Model #JXS66XX. These kits are available through your GE dealer, if the existing cutout is in a counter that has a backsplash (post- formed top) we recommend that you use the 4″... -
Page 5: Side Trim Extension Kit
SIDE TRIM EXTENSION KIT (CONT.) If there is a small gap between the sides of the range and the cabinets (up to 1/4″ each side), you can order a side trim extension kit, JXS86XX, through the GE service center. -
Page 6: Electrical Connections
Failure to wire your oven according to governing codes could result in a hazardous condition. If there are no local codes, your range must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70—... -
Page 7: Power Cord And Strain Relief Installation
NOTE: Do not install the power cord without a strain relief. The strain relief bracket should be installed before reinstalling the rear range wiring cover. Strain relief Power cord Skip to applicable power cord installation. - Page 8 The 4th grounding lead must be connected to the frame of the range with the ground plate and the ground screw. Remove the 3 lower terminal screws from the terminal block. Remove the ground screw and ground plate and retain them.
-
Page 9: 3-Wire Conduit Installation
Cut and discard the ground strap. DO NOT DISCARD ANY SCREWS. Insert the ground bare wire tip between the range frame and the ground plate (removed earlier) and secure it in place with the ground screw (removed earlier). Insert the bare wire (white/neutral) tip through the bottom center of the terminal block opening. -
Page 10: Install The Range
SLIDE RANGE INTO OPENING On models with a power cord, plug it into the receptacle. Locate the cord in the back of the range in a manner that it will not touch or be moved by the drawer. Position range cord so that... -
Page 11: Replacing The Oven Door
Installation Instructions REPLACING THE OVEN DOOR NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. Lift the oven door by placing one hand on each side. -
Page 12: Final Installation Checklist
When the range is elevated to the maximum height, there is a large space between the bottom of the range and the floor, referred to as the toe space. This may be visually objectionable. The legs should not be extended any further than to provide a maximum of 3″...