1. Manuals
  2. Brands
  3. Sony Manuals
  4. Computer Hardware
  5. DMW-S01NL
  6. Maintenance manual

Sony DMW-S01NL Maintenance Manual

Hide thumbs Also See for DMW-S01NL:
Table of Contents

Quick Links

SDTV NON-LINEAR PRODUCTION SYSTEM
DMW-S01NL
HDTV NON-LINEAR PRODUCTION SYSTEM
DMW-S02NL
FIBRE CHANNEL STORAGE UNIT
DMW-ST001
HDTV INTERFACE BOARD
DMW-IF02
MAINTENANCE MANUAL
Volume 1 1st Edition
Table of Contents
loading

Related Manuals for Sony DMW-S01NL

Summary of Contents for Sony DMW-S01NL

  • Page 1 SDTV NON-LINEAR PRODUCTION SYSTEM DMW-S01NL HDTV NON-LINEAR PRODUCTION SYSTEM DMW-S02NL FIBRE CHANNEL STORAGE UNIT DMW-ST001 HDTV INTERFACE BOARD DMW-IF02 MAINTENANCE MANUAL Volume 1 1st Edition...
  • Page 2 à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. DMW-S01NL (SY) Serial No. 10001 and Higher DMW-S02NL (SY) Serial No. 10001 and Higher DMW-ST001 (SY) Serial No. 10001 and Higher DMW-IF02 (SY) Serial No.
  • Page 3 LASER KLASSE 1 condition due to uneven mechanical loading. PRODUKT This SDTV/HDTV Non-linear Production System is classified as a CLASS 1 LASER PRODUCT. The CLASS 1 LASER PRODUCT label is located on the left panel. 1 (P) DMW-S01NL/S02NL/ST001...
  • Page 4 Brukt batteri returneres sicherzugehen, kleben Sie die Batteriepole z.B. mit apparatleverandøren. einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. Auf welcher Weise die Batterie abzunehmen ist, siehe den entsprechenden Hinweis in dieser Anleitung. 2 (P) DMW-S01NL/S02NL/ST001...

  • Page 5: Table Of Contents

    Installing Applications Programs ..........1-43 1-9-5. Reinstalling Application Programs .......... 1-45 1-9-6. Fibre Channel Storage Unit Setup Configuring Logical Drives ........... 1-46 1-10. Installation of DMW-IF02 ................ 1-48 1-10-1. Installing to DMW-S01NL ............1-48 1-10-2. Setup after installing ..............1-51 DMW-S01NL/S02NL/ST001...
  • Page 6 2. DMW-S01NL/DMW-S02NL/DMW-IF02 Service Overview 2-1. Digital media workstation/AV I/O block ............ 2-1 2-1-1. Location of Main Parts ............... 2-1 2-1-2. Removal of AV I/O Block ............2-2 2-1-3. Replacement of Main Parts ............2-2 2-2. Audio Control Panel .................. 2-19 2-2-1.
  • Page 7 4-4-12. Reading of AlertManager Setting File ........4-17 4-4-13. Setting the ESMPRO Report Service ........4-17 4-4-14. Other Additional Setting Items ..........4-22 4-4-15. Installation of Board Drivers ............ 4-24 4-4-16. Copy of Graphic Board Driver ..........4-24 4-4-17. System Initial Setup ..............4-24 DMW-S01NL/S02NL/ST001...

  • Page 9: Manual Structure

    If these manuals are required, please contact your local Sony Sales Office/Service Center..Operation Manual (CD-ROM) (Supplied with the DMW-S01NL/S02NL) This manual is necessary for application and operation (and installation) of this unit. Part number : 3-631-518-0X .

  • Page 10: Contents

    Using the Utility Software volume 2 This section explains the using processes of respective utility software, using by (9-967-947- ) DMW-S01NL/S02NL, DMW-ST001 and DMW-IF02. Section 6 Troubleshooting This section explains the error message and troubleshooting of this unit. Section 7 Electrical Alignment This section explains the electrical alignment for the maintenance of this unit.

  • Page 11: Trademarks

    In this manual such names are not indicated by R or TM. Note on system setting If setting of software or hardware is changed with method that not describes on this manual, can not guarantee the operation of unit. DMW-S01NL/S02NL/ST001...

  • Page 13: Installation

    Storage temperature : _20 dC to +60 dC units. Mass : ..DMW-S01NL/DMW-S02NL DMW-S01NL/DMW-S02NL Power requirements : AC 100 to 120 V/AC 220 to 240 V ±10 % Main unit (workstation with AV I/O block) 28 kg Media bar control panel 0.7 kg...

  • Page 14: Power Cord

    1-2-2. Power Cord 1. DMW-S01NL/DMW-S02NL and AC Adaptor Items USA/CANADA EUROPE Receptacle IEC320 IEC320 IEC320 . The power cord is not supplied with the DMW-S01NL/ Straight Straight Straight DMW-S02NL/DMW-ST001. Plug NEMA 5-15P CEE7type BS1363 Be sure to use the power cord that is applicable to places Cord type in the area as shown below.

  • Page 15: Installation Space

    1-3. Installation Space 1-3. Installation Space 1-3-1. DMW-S01NL/DMW-S02NL The following shows outward dimensions of the unit and each control panels. 1. Digital Media Workstation/AV I/O Block 205.7 Unit : mm DMW-S01NL/S02NL/ST001...
  • Page 16 1-3. Installation Space 2. Audio Control Panel Unit : mm DMW-S01NL/S02NL/ST001...
  • Page 17 1-3. Installation Space 3. Trackball Control Panel Unit : mm DMW-S01NL/S02NL/ST001...
  • Page 18 1-3. Installation Space 4. Media Bar Control Panel Unit : mm DMW-S01NL/S02NL/ST001...
  • Page 19 1-3. Installation Space 5. Jog & Shuttle Control Panel SHUTTLE Unit : mm DMW-S01NL/S02NL/ST001...

  • Page 20: Dmw-St001

    1-3. Installation Space 1-3-2. DMW-ST001 The following shows outward dimensions of the DMW-ST001. Unit : mm DMW-S01NL/S02NL/ST001...

  • Page 21: Connectors And Cables For Connection

    1-4. Connectors and Cables for Connection 1-4. Connectors and Cables for Connection Use the connector and the cable below or the equivalent at the tip when cables are connected to each connector on the unit. 1-4-1. DMW-S01NL/DMW-S02NL/DMW-IF02 1. Digital Media Workstation Panel display...

  • Page 22: Dmw-St001

    MONITOR OUT 3P jack 3P plug cable – UPSTREAM PORT USB (series B) USB (series B) cable 1-757-429-11 Accessory of the DMW-S01NL USB PORT 1-3 USB (series A) USB (series A) cable – 4. Trackball Control Panel Panel display Cable name Matching connector/cable Sony Part No.

  • Page 23: Input/Output Signals Of Connectors

    1-5. Input/Output Signals of Connectors 1-5. Input/Output Signals of Connectors The following shows input and output signals of each connector of the DMW-S01NL and DMW-ST001. 1-5-1. DMW-S01NL/DMW-S02NL/DMW-IF02 1. Digital Media Workstation DMW-S01NL AGP PCI1 PCI2 PCI3 PCI4 PCI5 PCI6...
  • Page 24 – - Outside view - 6 Line input/output : Phone jack Signal standard : Analog audio signal input/output Pin No. Signal name DCD1 RXD1 TXD1 DTR1 Pin No. Signal name – LINE IN DSR1 LINE OUT RTS1 CTS1 1-12 DMW-S01NL/S02NL/ST001...
  • Page 25 9 REF, IN A/B, OUT A/B : BNC x x x x x 5 Signal standard : Video input/output signal (SDI input/ output) Conform to SMPTE 259 M, level C, D Resolution ability 10 bit Audio input/output signal (embeded audio signal) Sampling frequency 48 kHz Resolution ability 20 bit 1-13 DMW-S01NL/S02NL/ST001...
  • Page 26 Signal standard : Conponent analog C Signal (BETACAM/D1-CAV) Video format 4 MON OUT L/R : Phono jack (RCA type) Signal standard : Analog audio signal output (unbalanced) Reference output level : _10 dBV Output impedance : Less than 50 Z 1-14 DMW-S01NL/S02NL/ST001...
  • Page 27 5 AUX1 IN L/R : Phono jack (RCA type) != REMOTE 1/2 : D-sub 9P, female Signal standard : Analog audio signal output (unbalanced) Signal standard : Conform to sony 9pin standard Reference input level : _10 dBV - Outside view - Input impedance : 10 kZ or more 6 AUX2 IN : 3P 1/8"...
  • Page 28 Reference output level : _10 dBV Output impedance : 470 Z 4 UPSTREAM PORT : USB (Seris B) Signal standard : USB standard Ver1.1 - Outside view - Pin No. Signal name – Vcc (+5 V) DATA (_) DATA (+) – 1-16 DMW-S01NL/S02NL/ST001...

  • Page 29: Dmw-St001

    Signal standard : Conform to FC-AL Public Loop standard Data transfer speed 100 Mbite/second DATA (_) DATA (+) - Outside view - – Pin No. Signal name FC_OUT (+) Vcc (+5 V) MIA_FAULT – KEY (not connection) FC_IN (+) FC_OUT (_) MIA_DISABLE – FC_IN (_) 1-17 DMW-S01NL/S02NL/ST001...

  • Page 30: Switch And Jumper-Pin Setting And Led Functions

    1-6. Switch and jumper-pin setting and LED functions 1-6. Switch and jumper-pin setting and . Fibre channel interface board LED functions 1-6-1. DMW-S01NL/DMW-S02NL/DMW-IF02 D102 D301 - D316 D103 1. Digital media workstation D901 - D904 D501 - D504 S302 S301 D101 .
  • Page 31 COR242 COR243 COR244 COR245 COR241 Switch S1 : System reset Press this S1 when hard resetting the CPU of AV I/O block S2 : Selector switch between 525 system and 625 system Factory setting S3 : BOOT_ROM Not used 1-19 DMW-S01NL/S02NL/ST001...
  • Page 32 S1004 CH-2 data for IC2301 (FPGA) to IC2401. Factory setting : Open S1103 CH-3 COR242, COR243 : For monitoring HIF . 3 Sound at DMW-S01NL S1104 CH-4 Factory setting Factory setting COR242, COR243 : Open AUD_HARNES is connected at DMW-S02NL S1003, S1004, S1103, S1104 : +24 dBu (Input level) ΧOR244, COR245 : For SDI input/output expander...
  • Page 33 CN304 : Connector for RS232C testing Press this S100 when reset the CPU and their peripheral circuit Factory use S102 (S102-1 to S102-4) : For design testing Use the following factory setting Factory setting S102-1 to S102-4 : OFF of all 1-21 DMW-S01NL/S02NL/ST001...

  • Page 34: Dmw-St001

    When several sets of the DMW-ST001 connects to the S300 D303 D302 S200 DMW-S01NL, different address number (0 to 11) sets to D301 D300 each set respectively. When one of DMW-ST001 connect to the DMW-S01NL, address number set to 0.

  • Page 35: Rack Mounting

    When more than two minutes passed during abnormal status, HDD is turned off automatically LCC check indicator : (umber) Light up when LCC or connection is abnormally LCC operate indicator : (green) Light up when turned on the LCC 1-23 DMW-S01NL/S02NL/ST001...

  • Page 36: Dmw-S01Nl/Dmw-S02Nl

    : 2 pcs (Supplied with DMW-S01NL/ Use B4 x 6 screws. Using other screws may cause DMW-S02NL) . Rack plate attaching screws : 4 pcs (Supplied with DMW-S01NL/ problems in the operations of the unit. (B4 x 8 : 7-682-561-09)
  • Page 37 B5 x 12 Unit : mm Claws (6) Tighten the screws (B4 x 6 : two screws each on the right and left) for adjusting the length of the adapter completely [the screws that were loosened in step (4)]. 1-25 DMW-S01NL/S02NL/ST001...

  • Page 38: Dmw-St001

    (The figure below shows the right rail.) Rear channel Clip nuts Clip nuts Securing nut and washer Adjusting slots Maximum depth of rail : 715 mm Minimum depth of rail : 504 mm 1-26 DMW-S01NL/S02NL/ST001...
  • Page 39 (6) Press the lock release button and open the front panel. (7) Fix the unit in the rack using supplied two screws and close the front panel. 10-32UNF x 1/2 10-32UNF x 1/2 10-32UNF x 1/2 44.45 Unit : mm Lock release button 10-32UNF x 1/2 Front panel 1-27 DMW-S01NL/S02NL/ST001...

  • Page 40: System Connection Example

    1-8. System Connection Example 1-8. System Connection Example 1-8-1. Connection with Betacam VTR . System using one analog VTR The figure below shows a system using one BVW-75/75P VTR. (When connecting with DMW-S01NL) Video monitor Audio monitor ANALOG VIDEO OUTPUT COMP...

  • Page 41: Connection With Digital Betacam Vtr

    1-8. System Connection Example 1-8-2. Connection with Digital Betacam VTR 1. System using one digital VTR The figure below shows a system using one DVW-A500/A500P VTR. (When connecting with DMW-S01NL) Video monitor Audio monitor REFERENCE THRU Reference signal MON OUT L/R...
  • Page 42 1-8. System Connection Example 2. System using two digital VTRs The figure shows a system using two DVW-A500/A500P VTRs. (When connecting with DMW-S01NL) a) AC power cord (Option) Video monitor Audio monitor b) 75 Z coaxial cable (Option) c) 9-pin remote control cable (Option)
  • Page 43 1-8. System Connection Example 3. System using one analog and one digital VTR The figure below shows a system using DVW-A500/A500P and BVW-75/75P VTRs. (When connecting with DMW-S01NL) a) AC power cord (Option) Video monitor Audio monitor b) 75 Z coaxial cable (Option)

  • Page 44: Connection With Hd Vtr

    1-8-3. Connection with HD VTR 1. System editing with 1080/50i or 1080/59.94i mode The figure below shows a system editing with 1080/50i or 1080/59.94i mode when using one HDW-F500 VTR. (When connecting with DMW-S02NL/DMW-S01NL with DMW-IF02) CH-1 HD monitor Audio monitor...
  • Page 45 1-8. System Connection Example 2. System editing with 1080/24PsF mode The figure below shows a system editing with 1080/24PsF mode when using one HDW-F500 VTR. (When connecting with DMW-S02NL/DMW-S01NL with DMW-IF02) CH-1 Audio monitor HD monitor CH-2 MON OUT L/R...

  • Page 46: System Initial Setup

    1) Start D : \CODI\CODI_v1.1.exe 2) Confirm the auto registration of Multi Media Control Driver after Re-boot 4. Application Software Installation ------ 1) Start D : \Setup.exe 2) Accept the License Agreement 3) Input User Name and Organization 1-34 DMW-S01NL/S02NL/ST001...

  • Page 47: System Startup And Shutdown

    If required, you can interrupt POST to change your BIOS starts. settings. The results of the POST are recorded in the DMW-S01NL/ S02NL mother board. You can change settings while POST is executing, but POST stops executing if you do. If you do not intend to change any settings you should not touch the mouse Normally the SONY logo is displayed.
  • Page 48 1-9. System Initial Setup Information displayed by POST The SONY logo is displayed while POST is running (except during the SCSI check), but the information in the following figure appears if you press the key. POST starts Memory count: Memory check...
  • Page 49 (1) Shut down Windows 2000. incorrect. (2) Power peripherals off. If this occurs, press the key to restart POST, and use the BIOS Setup Utility to set or change the board configuration. 1-37 DMW-S01NL/S02NL/ST001...

  • Page 50: Installing Graphic Board Driver

    3. Make sure to use the provided file for driver operation. (1) After log-in, Window appears. Go to step 2 directly. (3) Activate (In this case, do not click “Cancel”.) “C : \Programfiles\Sony\DMW\G400\Setup”. a) Click “My Computer”. b) Click “Local disk”. c) Click “Program Files”.
  • Page 51 (8) Click “Finish”. (5) Click “Next >”. (9) Wait until the computer restarts. After the computer restarts, be sure to log in again with administrator. (6) Click “Next >”. (The default administrator is without password.) (10)Click “Yes”, DualHead setting appears. 1-39 DMW-S01NL/S02NL/ST001...
  • Page 52 Change to the CRT monitor so that the screen area can be b) Set the screen color to “True Color (32 bit)”. set to “2560 x 1024” and the screen color to “True Color c) Click “Apply”. (32 bit)”. (15)Click “Advanced”. (13)Click “OK”. 1-40 DMW-S01NL/S02NL/ST001...
  • Page 53 1-9. System Initial Setup (16)Remove the check mark of “Use bus master- (17)Click “Close”. ing” in the option tab, and click “Apply”. (18)Click “Yes” to restart the system. 1-41 DMW-S01NL/S02NL/ST001...

  • Page 54: Installing Av Processing Board Driver

    Click “CODI”. d) Double click “CODI_v1.1. exe”. (4) As shown below, the AV processing board installer starts. Click “Next >”. (7) After restart, log in with administrator and confirm that the multi-media controller driver is registered automatically. 1-42 DMW-S01NL/S02NL/ST001...

  • Page 55: Installing Applications Programs

    (2) Start “D : \Setup.exe” from the explorer. (3) As shown below, the application installer is set up. Click “Next >”. (5) Enter the user name and position, select “All users who use this computer”, and click “Next >”. 1-43 DMW-S01NL/S02NL/ST001...
  • Page 56 1-9. System Initial Setup (6) Select “All” and click “Next >”. (9) After the installation end, the screen below appears. Click “Finish”. (7) Click “Install”. (8) The installation begins. (10)The restart confirmation screen appears. Click “Yes” to restart the system. 1-44 DMW-S01NL/S02NL/ST001...

  • Page 57: Reinstalling Application Programs

    (3) A shown below, the application installer is set up. Click “Next >”. (6) The uninstallation starts. (7) After the uninstallation end, the screen below appears. Click “Finish”. (4) Select “Remove,” and click “Next >”. (8) Install the applications while reference to “Sec. 1-9-4”. 1-45 DMW-S01NL/S02NL/ST001...

  • Page 58: Fibre Channel Storage Unit Setup

    3. Creating RAID HDD. However, note that RAID 0 uses no redundant parity When using the Sony Editing Software, two RAID must be bits. Therefore, all of the data on a logical drive is lost if created: one for video data and one for audio data.
  • Page 59 When processing ends, the following dialog appears. If you want to enable the settings immediately, click “Reboot Now” button to reboot the Main Unit. If you want to continue by creating or releasing more RAID, click the “CLOSE” button to close the dialog. 1-47 DMW-S01NL/S02NL/ST001...

  • Page 60: Installation Of Dmw-If02

    1. Turn off the power of all systems, disconnect of all the “Reboot Now” button to reboot the Main Unit. cables connected to a DMW-S01NL. If you want to continue by creating or releasing more 2. Remove the three screws (+B4 x 6) on the rear panel RAID, click the “CLOSE”...
  • Page 61 EX-848 board EX-849 board IF02 Assy CN102 Contacting face Flexible flat cable When connecting, make sure put contacting face of the flexible flat cable to bottom side, then connect it to CN102 on the EX-848 board. Slot 6 1-49 DMW-S01NL/S02NL/ST001...
  • Page 62 AUD cable AUD cable CP2401 170mm MPU-120 board IF02 Assy side Ferrite core CP2402 (20P) When installing, press the reverse side of the board (the opposite of connector inserting side) by finger etc. not to bend it. 1-50 DMW-S01NL/S02NL/ST001...

  • Page 63: Setup After Installing

    AUD cable HDVD cable 1 Turn on the power of the unit. 2 When the “SONY” logo appears on the screen, press the key. 3 Wait until BIOS setting screen is displayed. 4 Select the “Advanced” menu using arrow key USB cable <→>.

  • Page 65: Dmw-S01Nl/Dmw-S02Nl/Dmw-If02 Service Overview

    Section 2 DMW-S01NL/DMW-S02NL/DMW-IF02 Service Overview 2-1. Digital media workstation/AV I/O block 2-1-1. Location of Main Parts 1. Digital media workstation 2. AV I/O block 1 Power module 9 Graphic board !' CN-2068 board 2 FDD 0 AV processing board...

  • Page 66: Removal Of Av I/O Block

    (Set the stamp number on the flange facing in back and the flash side to the right side direction.) working it more than two persons. . When removing the AV I/O block, be careful not to pull the two connected cables as well as not to damage them. DMW-S01NL/S02NL/ST001...
  • Page 67 (4) Remove the three screws (PSW3 x 6) and remove the parts. . When reinstalling the front mask (PC), be sure to put CPU duct. back the handle of the power module to its place. CPU duct PSW3 x 6 DMW-S01NL/S02NL/ST001...
  • Page 68 (5) Remove the two screws (PSW4 x 8) and remove the (7) Remove the two screws (BVTP5 x 10) of each three fan assembly. finger guards and remove them. 1 DMW-S01NL Serial No. 30001 to 30015 (for J) Serial No. 10001 to 10050 (for SY) BVTP5 x 10 Finger guard...
  • Page 69 After replacing the FDD, be sure to perform the operation check, then confirm the reassembling of each parts. Note on reassembling the FDD Be sure tightening the screws while holding down the gasket that is situated on the panel surface portions of the FDD side of the unit. DMW-S01NL/S02NL/ST001...
  • Page 70 CD-ROM drive, FDD and blank panel makes evenly. PSW3 x 6 Audio cable Screw holes CD-ROM drive 5-inch bay holder PSW3 x 6 PSW3 x 6 DMW-S01NL/S02NL/ST001...
  • Page 71 (5) Remove the four screws (PSW3 x 6) and remove the HDD assembly by sliding it toward backward. (6) Remove the four screws (#6-32UNC x 6) and remove the HDD. #6-32UNC x 6 #6-32UNC x 6 PSW3 x 6 DMW-S01NL/S02NL/ST001...
  • Page 72 BIOS setting menu. And also, make sure to (Refer to “Sec. 5-1”.) erasing the error information of the DIMM. (Refer to “Sec. 5-1”.) . After replacing the DIMM, perform the operation check using the utility software “I-Ciser”. (Refer to “Sec. 5-2-1”.) DMW-S01NL/S02NL/ST001...
  • Page 73 Mother board After replacement of the battery, BIOS setting contents becomes indefinite status, perform the BIOS setting. (Refer to “Sec. 5-1”.) Adjustment after replacing the battery After replacement the battery, perform the BIOS setting. (Refer to “Sec. 5-1”.) DMW-S01NL/S02NL/ST001...
  • Page 74 (2) Confirm and test the following items using the disk utility. (Refer to “Sec. 5-6-3”.) If the disk utility does not set up normally, it considers that poor contact may occurs. Therefore, insert the DSK-11 board in the PCI slot again. 2-10 DMW-S01NL/S02NL/ST001...
  • Page 75 6 Click “Test Start” button. After the test ends, confirm the message “Test is Completed !” is displayed on the window. 7 Press “Open Log File” button to open the inputting log file. 8 Confirm the “CompErr = 0” of result-A in log con- tents. 2-11 DMW-S01NL/S02NL/ST001...
  • Page 76 Adjustment after replacement of the IF02 Assy (DMW-IF02) Confirm the version No. using the utility software of IF02 Assy (DMW-IF02), and confirm that the no error is found by self diagnosis. (Refer to “Sec. 5-7-2, 5-7-3”.) 2-12 DMW-S01NL/S02NL/ST001...
  • Page 77 (Refer to “Sec. 1-6-1”.) . After replacing the mother board, perform the BIOS setting. (Refer to “Sec. 5-1”.) . Service tool required Box driver (For M12) ... Part No. : 7-700-751-05 Box driver (For M7) ... Part No. : 7-640-005-30 2-13 DMW-S01NL/S02NL/ST001...
  • Page 78 After replacing the AH-65 board, be sure to perform the operation check, then reassembling of each parts. Adjustment after replacement of the AH-65 board After replacing the AH-65 board, confirm the output voltage of the DC-DC converter is correct. (Refer to “Sec. 7-2”.) 2-14 DMW-S01NL/S02NL/ST001...
  • Page 79 Black CP2402(20P) SDI OUT CN3001, PGM OUT SYSTEM I/F IN CN2701, FRM PC Orange * When DMW-IF02 is installed in DMW-S01NL. SYSTEM I/F OUT CN2601, TO PC Yellow MON OUT CN3201, MON OUT 1 Green Adjustment after replacement of the MPU-120 board...
  • Page 80 (4) Disconnect the three cables and one coaxial cable. PWH3 x 5 In case of DMW-S02NL (or DMW-S01NL with DMW- IF02), disconnect the HDVD cable to add to above the cables. (5) Remove the fourteen screws (BVTP3 x 8) of the rear...
  • Page 81 Section 7, Electrical Alignment. B3 x 5 B3 x 5 CN-2069 board CN-2068 board CN102 CN101 Cables After replacing the CN-2068 and CN-2069 boards, be sure to perform the operation check and adjustment, then perform the reassembling of each parts. 2-17 DMW-S01NL/S02NL/ST001...
  • Page 82 . When wiring the cable, fasten it with wire holder on the Panel indication MTS-11 board Color CN-2080 board to have no loosing. REF OUT2 CN5401, BB_OUT2 Black 2-18 DMW-S01NL/S02NL/ST001...

  • Page 83: Audio Control Panel

    2-2. Audio Control Panel 2-2. Audio Control Panel 2-2-1. Location of Boards 1 CN-2002 board 2 CPU-315 board 3 KY-471 board 4 KY-472 board 5 SV-220 board 2-19 DMW-S01NL/S02NL/ST001...

  • Page 84: Removing Of Cabinet

    BVTP3 x 8 BVTP3 CN405 Flat Spring (B) cables Fader panel (lower) assembly SV-220 board assembly CPU-315 board BVTP3 x 8 Ferrite cores CN404 Fader panel assembly CN403 When disconnecting / re-connecting the flat cable, be careful not damage it. 2-20 DMW-S01NL/S02NL/ST001...

  • Page 85: Replacement Of Main Parts

    CPU-315 board bracket assembly SV-220 board B3 x 6 Fader Fader panel (lower) assembly (5) Install the fader in the reverse order of steps (1) through (4). . Setting and adjustment are no necessity after replace- ment of fader. 2-21 DMW-S01NL/S02NL/ST001...
  • Page 86 No. to version up is equal to existing panel version No., there is no necessity to version up of the firmware.) Refer to Sec. 5-4-3 Step 2, Program download for version up procedure and version confirmation of this firmware. 2-22 DMW-S01NL/S02NL/ST001...

  • Page 87: Trackball Control Panel

    2-3. Trackball Control Panel 2-3. Trackball Control Panel 2-3-1. Location of Main Parts 1 Trackball 2 KY-473 board 3 CPU-316 board 2-23 DMW-S01NL/S02NL/ST001...

  • Page 88: Removing Of Cabinet

    (6) Peel the base sheet from the trackball panel to remove CN100 Board assembly Trackball panel CPU-316 Earth terminal board BVTP3 x 8 USB bracket PWH3 x 5 Connection cord (USB) Trackball panel BVTP3 x 8 Base sheet 2-24 DMW-S01NL/S02NL/ST001...

  • Page 89: Replacement Of Main Parts

    No. to version up is equal to existing panel version No., there is no necessity to version up of the firmware.) Refer to Sec. 5-4-3 Step 2, Program download for version up procedure and version confirmation of this firmware. 2-25 DMW-S01NL/S02NL/ST001...

  • Page 90: Media Bar Control Panel

    2-4. Media Bar Control Panel 2-4. Media Bar Control Panel 2-4-1. Location of Boards 1 CPU-319 board 2 KEY-48 board 2-26 DMW-S01NL/S02NL/ST001...

  • Page 91: Removal Of Cabinet

    (bottom) from the knob case (top). BVTP3 x 8 CN101 CN209 P3 x 4 CPU-319 board Knob shield (bottom) Connection cord (USB) Encorder Harness knobs BVTP3 x 8 KEY-48 board PWB support Knob case (Top) BVTP3 x 8 Screw covers 2-27 DMW-S01NL/S02NL/ST001...

  • Page 92: Replacement Of Main Parts

    No. to version up is equal to existing panel version No., Nuts there is no necessity to version up of the firmware.) Refer Rubber to Sec. 5-4-3 Step 2, Program download for version up procedure and version confirmation of this firmware. Hinge Hinge Hinge 2-28 DMW-S01NL/S02NL/ST001...

  • Page 93: Jog & Shuttle Control Panel

    2-5. Jog & Shuttle Control Panel 2-5. Jog & Shuttle Control Panel 2-5-1. Location of Main Parts 1 Clutch assembly, electromagnetic 2 KY-470 board 3 CPU-314 board 2-29 DMW-S01NL/S02NL/ST001...

  • Page 94: Removing Of Cabinet

    KY-470 board Lens Device control Device control Device control panel panel (lower) panel (lower) (top) CPU-314 board CPU-314 board BVTP3 x 8 BVTP3 x 8 CN400 CN400 When disconnecting/re-connecting the flat cable, be careful not to damage it. 2-30 DMW-S01NL/S02NL/ST001...

  • Page 95: Replacement Of Main Parts

    Rear panel BVTP3 x 8 CPU-314 board Harness Shield plate (lower) Shield plate (lower) B3 x 6 Device control Device control panel (top) assembly panel (lower) When disconnecting/re-connecting the flat cable, be careful not to damage it. 2-31 DMW-S01NL/S02NL/ST001...
  • Page 96 (7) Install the electromagnetic clutch assembly in the reverse order of steps (1) through (6). Adjustment after replacement After replacement of the electromagnetic clutch assembly, make sure to "Search Dial Pulse Amplifier Adjustment" of the DET-11 board. (Refer to Section 7.) 2-32 DMW-S01NL/S02NL/ST001...

  • Page 97: Dmw-St001 Service Overview

    Section 3 DMW-ST001 Service Overview 3-1. Location of the boards 1 Disk module 2 Power supply unit 3 Drive fan pack 4 Link control card DMW-S01NL/S02NL/ST001...

  • Page 98: Replacement Of Main Parts

    Power Supply . When replacement of the drive fan pack, it can removing . When replacing the power supply unit, confirm the DMW-S01NL system was stopped. and reassembling just as remaining ON the power of the DMW-ST001. . When drive fan pack was removed, cooling check indicator Adjustment after replacing the power supply unit of power supply unit will blinking.
  • Page 99 Adjustment after replacing the disk module After replacement of the disk module, performs the remaking of the logical drive using disk utility. (Refer to Sec. 5-6-5, 2) 18GB Disk Module : EMC Parts No. SONY18 DMW-S01NL/S02NL/ST001...

  • Page 100: Caution Of Transportation

    When transporting the DMW-ST001, using the provided (exclusive use) packing case and fixed to the pallet as shown in follows figure. Shipping carton box : EMC Part No. SDAEPKG Outside box Inside box DMW-ST001 10-32UNF x 1/2 (With spring washer and plain washer) Pallet 10-32UNF x 1/2 (With spring washer and plain washer) DMW-S01NL/S02NL/ST001...

  • Page 101: Upgrading Of Software Version And Reinstallation

    Program Files Sony Proc Sys ....Device driver folder of AV I/O block and Control panels SonyDTF ........ Device driver folder of Sony tape driver Setup.exe ....... Installer of application programs QuickTime ......Quick Time Folder English ......For English version Japanese ......

  • Page 102: Replacement Of Hard Disk

    2. The installer of Windows 2000 is started. 3. Carry out the installation according to the given instructions. 4. Product key is stuck on the top board of the DMW-S01NL/S02NL. 1. Use NTFS for the partition. 2. Before installation, remove all USB devices.
  • Page 103 7. Click “Finsh” button when Windows components wizard is completed. 3. Click “Add/Remove Windows Components” to open 8. Click “Close” button in Add/Remove Programs dialog. Windows components wizard dialog. 9. Double click “Administrative Tools” icon on the control panel to display Administrative Tools dialog. DMW-S01NL/S02NL/ST001...
  • Page 104 “Properties” of Context Menu to display SNMP Service Properties (Local Computer) dialog. “Add to list” button will be disabled, and “Remove from list” button becomes clicable. 13. Click “Add...” button to display SNMP service configuration dialog. 14. Enter IP address “127. 0. 0. 1”. DMW-S01NL/S02NL/ST001...
  • Page 105 “OK” button. 19. Click “OK” button in SNMP Service Properties dialog 16. Click “Security” tab. for local computer. SNMP Service Properties dialog will be closed for local computer. 20. Click “X” button in Service dialog to close it. DMW-S01NL/S02NL/ST001...

  • Page 106: Installation Of Difference Module

    2. Double click “D : \HAL_Update\W2K\update.exe”. Setup Message dialog will be displayed. 3. Click “OK” button. Windows 2000 Setup dialog will be displayed. 4. Click “Restart Computer”. 3. Double click “Computer Management” icon. Computer Management dialog will be displayed. DMW-S01NL/S02NL/ST001...
  • Page 107 5. Click the mouse right button on Group List. Context Menu will be displayed. 7. Enter “NvAdmin” for group name. 8. Click “Create” button. 9. Click “Close” button. New Group dialog will be closed. 10. Close Computer Management dialog. DMW-S01NL/S02NL/ST001...

  • Page 108: Installation Of Serveragent

    3. Carry out the installation according to the given instructions. Install ServerAgent which is an error monitor tool for Set Installation folder to c : \program files\Sony\DMW\Agent. Windows. Use installation CD-ROM for this installation. 1. Insert installation CD-ROM into CD-ROM drive.

  • Page 109: Halt Of Dmi Event Communication Function

    1. Select “Settings” → “Control Panel” from Start Menu. 5. Carry out the installation according to the given instructions. Set Installation folder to c : \program files\Sony\DMW\ESMPRO. 2. Double click “Administrative Tools” icon. Administrative Tools dialog will be displayed. The installation of ESMPRO is completed.

  • Page 110: Dmi Supervisory Function Disable Check

    “Properties” of Context Menu. Dmi Event Watcher Properties for local computer dialog will be displayed. DMI is not used on DMW-S01NL/S02NL, thus DMI supervisory function shall be OFF. 1. Select “Settings” → “Control Panel” from Start Menu.

  • Page 111: Setting Of Memory Dump

    4-4-8. Setting of Memory Dump 3. Click “Advanced” tab. This is made to collect memory dump (debugging informa- tion) in DMW-S01NL/S02NL. 1. Select “Settings” → “Control Panel” from Start Menu. 2. Double click “System” icon. System Properties dialog will be displayed.
  • Page 112 Click “OK” button, close the dialog. and click “Set” button. The size of the virtual memory is set approximately 1.5 times as much as the mounted memory size (800 MB). 6. Click “Performance Options...” button. 9. Click “OK” button. 10. Restart the computer. 4-12 DMW-S01NL/S02NL/ST001...

  • Page 113: Setting Of Dr. Watson

    (log). Following configuration is required to correct diagnostic information. 1. Click “Run...” from Start Menu. 2. Enter “drwtsn32.exe” in “Open” box, and click “OK” button. Dr. Watson dialog will be displayed. 4-13 DMW-S01NL/S02NL/ST001...

  • Page 114: Creating Of Windows 2000 Setup Boot Disk

    Disk” is needed to start and recover the system. Prepare this in advance. 4 floppy disks are necessary for this operation. 1. Insert Windows 2000 Professional CD-ROM into CD- ROM drive. 2. Double click D:\BOOTDISK\MAKEBT32.exe. 5. Click “OK” button. 4-14 DMW-S01NL/S02NL/ST001...

  • Page 115: Setting Of Esmpro Server Manager

    Auto Discover (TCP/IP) dialog will be opened. The following floppy disks will be created: . Windows 2000 Setup Boot Disk . Windows 2000 Setup Disk #2 . Windows 2000 Setup Disk #3 . Windows 2000 Setup Disk #4 4-15 DMW-S01NL/S02NL/ST001...
  • Page 116 The destination for connection will be searched and recorded. 4. Click “Range” Radio button to select it. 8. Click “Close” button when it becomes active. Close Auto Discover (TCP/IP) dialog. 5. Enter “127. 0. 0. 1” in both Start Address and End Address boxes. 4-16 DMW-S01NL/S02NL/ST001...

  • Page 117: Reading Of Alertmanager Setting File

    5. Select AmsetingDMW. dat from ESMPRO folder in Installation CD-ROM, and click “Open” button. Restore Alert Manager Setting dialog will be opened. 6. Click “OK” button. Setting information will be read. (3) Select “Tools” → “Report Settings...” from Menu. AlertManager will be started. 4-17 DMW-S01NL/S02NL/ST001...
  • Page 118 (7) Also click the “OK” button to close the Base Setting dialog. (8) Click “Setting” → “Destination Setting...” from Alert Manager dialog menu. Destination Setting dialog will be displayed. Internet Mail Base Setting dialog will be displayed. (9) Click the “Internet Mail”, and click the “Modify ID...” button. 4-18 DMW-S01NL/S02NL/ST001...
  • Page 119 Via the SMTP Server you have previously set, make sure that you can send a mail to the “To:” address. (12)Click the “OK” button to close the Internet Mail Destination Setting dialog. Close the ID Setting dialog as well. The Group Setting dialog will be displayed. 4-19 DMW-S01NL/S02NL/ST001...
  • Page 120 The time table is initially set at one hour interval. Modify the setting appropriate to each services. At the same time, an Alert Message is also sent to the mail address. 4-20 DMW-S01NL/S02NL/ST001...
  • Page 121 Link Destination dialog below will be displayed. (3) Clicking the mouse right button for this error code displays the context menu. You can configure the reporting setting for each error. However, note that a disabled item at the Base setting section is invalid. 4-21 DMW-S01NL/S02NL/ST001...

  • Page 122: Other Additional Setting Items

    (4) Change the settings according to the following instruc- tions : . Select “Show hidden files and folders” radio button. . Uncheck “Hide file extension for known file types” check box. (5) Click “OK” button to close the dialog. 4-22 DMW-S01NL/S02NL/ST001...
  • Page 123 2. Cancel of Driver’s Signature Check (3) Click “Hardware” tab, and click “Driver Signing...” button. The Driver developed by SONY has not been approved by Driver Signature Option dialog will be displayed. Microsoft. Consequently, Signature verification is promp- ted for every installation. The following setting can be carried out so as to avoid such procedure.

  • Page 124: Installation Of Board Drivers

    3. Click “My Computer” icon from Explorer. 4. Click Local Disk drive (C :). 5. Click “Program Files” folder. 6. Click “Sony” folder. 7. Click the right-side mouse button on “DMW” folder, click “Paste” from Context Menu. 8. Click “DMW” folder, then confirm that “G400” folder is copied under “DMW”...
  • Page 125 The material contained in this manual consists of digital multimeters that have a 20 V AC range information that is property of Sony Corporation and is are suitable. (See Fig. A) intend solely for use by the purchasers of the equipment described in this manual.
  • Page 126 DMW-S01NL (SY) DMW-S02NL (SY) Printed in Japan Sony Corporation DMW-ST001 (SY) E 2001. 4 26 Communication System Solutions Network Company 9-967-930-01 ©2001...

This manual is also suitable for:

Dmw-s02nlDmw-st001Dmw-if02

Table of Contents