How To Connect Remote Controller For Wire Operation - Toshiba RAS-16N3AV2 Series Installation Manual
Hide thumbs
Also See for RAS-16N3AV2 Series:
- Installation manual (276 pages) ,
- Owner's manual (11 pages) ,
- Owner's manual (8 pages)
Table of Contents
Available languages
Available languages
Connecting cable
Terminal block
Cord clamp
Screw
Screw
Terminal cover
NOTE
• Use stranded wire only.
• Wire type : More than H07RN-F or 245 IEC66 (1.0 mm
How to Connect Remote Controller
for Wire Operation
CAUTION
• Be sure to install control wire along
the wall so that there is no slack and
À x remote controller on the wall.
For indoor unit
1. Open the air inlet grille upward.
2. Securely remove two screws at the front panel.
3. Slightly open the lower part of the front panel then pull the upper part of
the front panel toward you to remove it from the rear plate as shown on
À gure 1.
4. After removing the front panel, remove the Display unit and open the
cover as shown on À gure 2 and 3.
5. Arrange the control wire as detail and speciÀ cation as shown on À gure
4.
6. Securely connect the control wire to terminal of Display unit board as
shown on À gure 5 (tighten À rmly but not over 0.12 N·m (0.01 kgf·m)).
7. Set the control wire throughout at slot on front cover of Display unit then
reassembly Display with main casing by reverse process of À gure 2 and
3. Make sure the control wire must not be pressed by front and rear
cover of Display unit.
8. Set the control wire out from indoor unit same portion as power supply
and connecting cable as shown on À gure 6.
9. Reassembly the indoor unit by reverse process of 1 to 3.
Air inlet grille
Display unit
100 mm
10 mm
10 mm
90 mm
Stripping length of the connecting cable
2
or more)
Indoor unit
Control wire
Remote controller
1
Front panel
2
Display board
* Wire size 28-22AWG
or 0.08-0.32 mm
Outer diameter not over 4.7 mm,
control wire length less than 30 m.
Earth line
Tighten À rmly but
not over 0.12 N·m
(0.01 kgf·m)
For remote controller
1. Remove cover of remote controller by sliding down and take it out.
2. If batteries are exist, please take them out. The combination of using
wire controller and batteries may cause of batteries explosion.
3. Make hole for insert control wire by use screwdriver break the polyester
sheet as shown on À gure 7.
4. Insert control wire from rear side of remote controller as shown on
À gure 8.
5. Fix control wire which arrange as shown on À gure 9 and ! to terminal
by provided screws (tighten À rmly but not over 0.25 N·m (0.03 kgf·m)).
6. Set control wire through gutter way at rear side of remote controller as
shown on À gure ".
7. Fix provided screw (Ø3.1×16L) on the wall to hang remote controller as
shown on À gure #.
8. Mark and arrange hole for À x below screw (Ø3.1×25L) as shown on
À gure #.
9. Assembly battery cover which provided with accessory bag then use
provide screw (Ø3.1×25L) to À x battery cover together with wall as
shown on À gure $ (tighten À rmly but not over 0.15 N·m (0.02 kgf·m)).
10. Reassembly cover of remote controller.
30 mm
10 mm
* Wire size 28-22AWG
2
or 0.08-0.32 mm
Outer diameter not over 4.7 mm,
control wire length less than 30 m.
3
5
70 mm
2
5 mm
5
Terminal
Control wire
7
Polyester sheet
close hole for
insert control wire
9
Control wire
Terminal
Control wire
Hole for hang
remote controller
Remote controller
Remote controller
"
4
Notch for wire out
6
Control wire
8
Control wire
!
Tighten À rmly but
not over 0.25 N·m
(0.03 kgf·m)
Control wire
Screw (Ø3.1×16L)
for hang remote
controller
Wall
Screw (Ø3.1×25L)
for À x battery cover
#
Hide quick links:
Table of Contents
